10 PIECE LOW VOLTAGE GARDEN LIGHT SET

Transcription

1 10 PIECE LOW VOLTAGE GARDEN LIGHT SET STOCK No PART No.GL10 INSTRUCTIONS IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY TO ENSURE THE SAFE AND EFFECTIVE USE OF THIS TOOL. 04/2000

2 SPECIFICATION Whilst every effort has been made to ensure that the accuracy of information given in this booklet is correct at time of going to print, the Draper Tools policy of continuous improvement determines the right to change specification without notice. Bulb wattage 7 W Transformer input 230V/50Hz Transformer output 12V/60V.A. 5A Cable length 18 M (approx.) CHECKING CONTENTS 1. Tier A 8 pieces 7. Cable (SPT-1 18ANGx2C 105 1M) 1 piece 2. Tier B 8 pieces 8. Connector 8 pieces 3. Tier C 8 pieces 9. Stem 8 pieces 4. Lampshade 8 pieces 10. Stake 8 pieces 5. Bulb(12V/7W, wedge based) inc. spare 10 pieces 11. Transformer 1 piece 6. Socket 8 pieces 12. Floodlight 2 pieces

3 GARDEN LIGHT ASSEMBLY INSTRUCTIONS This light set contains two garden floodlights which are already assembled. However the louvred garden lights should be assembled as follows: 1. Press the top of the lampshade into Tier A. 2. Slide Tier B onto the tapered end of the lampshade and secure in the slots provided. 3. Secure Tier C onto the bottom of the lampshade by aligning each lug with the slots provided on Tier C. The most efficient way to secure Tier C to the lampshade is to use both thumbs either side of each lug and push down until they click into place. 4. Loop the cable over the top of the connector and push it into the recess provided on each side. Note the arrows moulded on the connectors, indicating the top. 5. Push the connector into the stem and gently pull the cable down. If low level lighting is required, omit the stem and connector and loop the cable over the top of the stake instead. 6. For standard height lighting, push the stake into the other end of the stem. 7. Slide the connector into the socket by aligning the exposed cable with the flat inner walls of the socket. Push the connector firmly in until it is secured. 8. Carefully push the bulb into the top of the socket. 9. Insert the socket into the underside of Tier C by aligning the lugs with the grooves and twist the socket into place. 10. Carefully push the garden light into soft ground. If the ground is hard, prepare a small hole. 11. Repeat the above procedure for each light. 1. Tier A 2. Tier B 3. Tier C 4. Lampshade 5. Bulb Socket 7. Cable 8. Connector (0ptional) 9. Stem (optional) 10. Stake 11. Transformer 12. Floodlight

4 TRANSFORMER INSTALLATION AND OPERATION 1. The transformer supplied with this light set is not weatherproof, therefore it MUST ONLY be installed indoors. 2. Place the transformer in a safe, dry position where there is a protected mains supply power socket. 3. The transformer must not be placed in a confined space, as this may cause it to overheat. 4. The transformer is fitted with a 1.5 metre (approx.) power supply cable and 3 pin 5A fused plug. The cable and plug must not be exposed to harsh treatment. 5. The transformer is also supplied with a 18 metre (approx.) 12 volt, low voltage cable (SPT-1 18AWG x2c 105 ). After the light assemblies have been pushed into the ground, stretch the cable out to the desired route following where the garden lights have been positioned. 6. The garden light kit will be switched "ON" or "OFF" at the mains supply power socket in which the transformer is plugged. GARDEN LIGHT KIT CONNECTION INSIDE OUTSIDE NOTE: Place the transformer in a safe, dry position where there is a protected mains supply power socket

5 BULB REPLACEMENT Spare bulbs are available, quote Stock No (pack of 4). 1. Twist the lampshade while holding the socket and stem/stake firmly. 2. Lift off the lampshade to expose the bulb. 3. Gently pull the bulb out of the socket, to avoid it breaking off (caution: may be hot!). 4. Carefully insert the specified replacement bulb (8W) into the top of the socket, taking great care not to twist or force it, as this will break it. 5. Replace the lampshade and twist into place. GUARANTEE Draper Garden Lights have been carefully tested and inspected before shipment and are guaranteed to be free from defective materials and workmanship for a period of 12 months from the date of purchase except where items are hired out when the guarantee period is ninety days from the date of purchase. Should the unit develop any fault, please return the complete item to your nearest authorized warranty repair agent or contact Draper Tools Limited, Chandler s Ford, Eastleigh, Hampshire. SO53 1YF. England. Telephone: (023) If upon inspection it is found that the fault occurring is due to defective materials or workmanship, repairs will be carried out free of charge. This guarantee does not apply to normal wear and tear, nor does it cover any damage caused by misuse, careless or unsafe handling, alterations, accident, or repairs attempted or made by any personnel other than the authorized Draper warranty repair agent. This guarantee applies in lieu of any other guarantee expressed or implied and variations of its terms are not authorized. Your Draper guarantee is not effective unless you can produce upon request a dated receipt or invoice to verify your proof of purchase within the 12 month period. Please note that this guarantee is an additional benefit and does not affect your statutory rights. Bulbs are consumable item and are not covered by this guarantee. Draper Tools Limited

6 NOTES - 5 -

7 NOTES - 6 -

8 DRAPER TOOLS LIMITED, Hursley Road, Chandler's Ford, Eastleigh, Hants. SO53 1YF. England. Tel: (023) Fax: (023) YOUR DRAPER STOCKIST Published by Draper Tools Ltd. No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic, mechanical photocopying, recording or otherwise without prior permission in writing from Draper Tools Ltd.