OutCast & Outcast Jr Skinit Application Guide

Transcription

1 OutCast & Outcast Jr Skinit Application Guide Tools you ll need Adhesive tape 2 Clean cloths Scissors Squeegee tool Introduction: This guide is intended exclusively for OutCast and OutCast Jr. Please feel confident as you work through the application process described in this document as it is simple and easy to follow. Also keep in mind that if you make mistakes you can always remove the skin and reapply it until you are happy with the results. Preparation: Please follow the instructions to prepare your unit prior to installing the skin. Place speaker on a raised flat surface Clean surface of unit with a damp Dry unit with a second clean in well illuminated area. cloth and wipe surface of unit to cloth remove any debris OutCast & Jr Skinit Application Guide Rev 3.0 1

2 Cut large middle section piece of SKINIT into strip Tip: Scissors placed on the cutting line edge will glide smoothly along the edge Separate middle section skin OutCast & Jr Skinit Application Guide Rev 3.0 2

3 Application 1. Top section skin (Head) 1.2 Locate top section skin 1.1 Choose a spot to carefully start removing skin 1.3 Carefully remove skin from backing paper 1.4 Center skin piece as much as possible OutCast & Jr Skinit Application Guide Rev 3.0 3

4 1.5 Apply the skin with hands or Squeegee tool trying to avoid any wrinkles or bubbles 1.6 Remove skin and reapply it if wrinkles and bubbles can not be removed 1.7 Carefully remove any remaining bubbles 1.8 Skin installed on OutCast s head OutCast & Jr Skinit Application Guide Rev 3.0 4

5 2. Top section (surround) 2.1 Locate top section strip 2.2 Bend one of the edges of the top section strip 2.3 Gently remove top strip from backing paper 2.4 Align strip with the Auxiliary input port area before applying OutCast & Jr Skinit Application Guide Rev 3.0 5

6 2.5 Using the unit s lower edge as a point of reference wrap strip around the unit making sure it stays aligned. Carefully remove any remaining bubbles 2.6 Top strip installed on OutCast unit OutCast & Jr Skinit Application Guide Rev 3.0 6

7 3. Middle Section: Please pay special attention to this skin as it is the most prominent piece in the unit. Alignment is critical especially if the skin has an image or a pattern. 3.1 Get the middle section strip that you previously cut with scissors. 3.2 Locate the center of the skin Center 3.3 Locate the center of the unit. This is the point that 3.4 Without removing the backing paper, align skin s center to unit s center and wrap skin around keeping the same the skin piece will be aligned with. distance between the edge of the skin and the line that separates the head from the main body of the unit. OutCast & Jr Skinit Application Guide Rev 3.0 7

8 3.5 Tip: If the skin has an artistic image or pattern, align it in a way that there s continuity between the top and middle section pieces 3.6 Ensure the skin is aligned as much as possible to the speaker s division line 3.7 Once the skin has been aligned around the speaker, secure the right side with adhesive tape. Please note, it is easier if 2 people perform this step, one person holding the skin in place and the second securing it with adhesive tape OutCast & Jr Skinit Application Guide Rev 3.0 8

9 3.8 Secure the left side of the skin with tape 3.10 Carefully remove 4 of skin from the backing paper 3.9 Apply tape on top and bottom edges 3.11 Cut the exposed backing paper OutCast & Jr Skinit Application Guide Rev 3.0 9

10 3.12 Stick the peeled off portion of the skin to the unit. You can use your hands or the Squeegee tool to remove bubbles Remove the right side of the skin unwrapping the unit until you reach the portion that you stuck to the unit in the previous step Once you reach the part that is adhered to the unit, remove the remaining backing paper Re wrap the unit sticking the skin and removing any bubbles or wrinkles as they occur Complete the turn and remove the tape from the skin Remove any remaining wrinkles and bubbles. OutCast & Jr Skinit Application Guide Rev

11 3.18 Unit with middle strip section installed OutCast & Jr Skinit Application Guide Rev

12 4. Bottom section Outcast only (Not applicable to Outcast Jr) 4.1 Locate the bottom strip 4.2 Locate the center of the bottom strip Letter c 4.3 Center and apply the strip to the unit. Tip: The letter c in the OutCast logo can be used as a reference 4.4 Wrap strip around bottom section aligning it evenly along the base of the speaker OutCast & Jr Skinit Application Guide Rev

13 4.5 Remove any wrinkles and bubbles as you go 4.6 Bottom strip installed on OutCast OutCast & Jr Skinit Application Guide Rev

14 Notes: 1. The alignment of the middle section side may not match 100% 2. The skins can be removed and re installed if done carefully OutCast & Jr Skinit Application Guide Rev

15 Finished unit OutCast & Jr Skinit Application Guide Rev