Material Safety Data Sheet

Transcription

1 Material Safety Data Sheet Ingersoll Rand # 10 Oil Section 1. Product and Company Identification Product Name Synonym Product Use : Ingersoll Rand # 10 Oil : Not Available : Lubricant Validation Date : 01/18/2011 In Case of Emergency MSDS authored by: : TOOL HLP Section 2. Hazards identification Emergency Overview : Ingersoll Rand Industrial Technologies 800-A Beaty Street, P.O. Box 1600, Davidson, NC Physical state Odor Colour Hazard Summary OSHA Hazard : Liquid. : Mild. : Amber : May cause eye and skin irritation. : This material is not hazardous under the criteria of the federal OSHA Hazard communication standard 29CFR Potential health effects Primary routes of entry Aggravated medical condition Inhalation Skin Eyes Ingestion Symptoms of overexposure : Eye contact, Skin contact : Skin Disorders : May cause respiratory tract irritation. : May cause skin irritation. Prolonged or repeated contact may dry skin and cause irritation. : May cause eye irritation. : May be harmful if swallowed. Aspiration hazard if swallowed - can enter lungs and cause damage. : No information Available. Carcinogenicity IARC OSHA NTP ACGIH : No component of this product present at levels greater than or equal to 0.1% is identified as probable, possible or confirmed human carcinogen by IARC. : No component of this product present at levels greater than or equal to 0.1% is identified as a carcinogen or potential carcinogen by OSHA. : No component of this product present at levels greater than or equal to 0.1% is identified as a known or anticipated carcinogen by NTP. : No component of this product present at levels greater than or equal to 0.1% is identified as a carcinogen or potential carcinogen by ACGIH. Section 3. Composition / Information on Ingredients Hazardous components No ingredients are hazardous according to HCS criteria. Ingersoll Rand # 10 Oil /Automotive Air Tool Lubricant MSDS Page 1 of 5

2 Section 4. First Aid Measures First Aid Procedures Inhalation Skin contact Eye Contact Ingestion : If inhaled. Move to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. In case of bluish discoloration (lips, ear lobes, fingernails), give oxygen as quickly as possible. If symptoms persist, call a physician. : In case of skin contact, Wash off with soap and water. Remove contaminated clothing and shoes. Wash contaminated clothing before re-use. Get medical attention if irritation develops and persists. : In case of eye contact, Rinse thoroughly with plenty of water, also under the eyelids. If eye irritation persists, consult a specialist. : If swallowed, DO NOT induce vomiting. Consult a physician if necessary. Notes to physician Symptoms Treatment : No information available. : No information available. Section 5. Fire-Fighting Measures Flammable Properties Flash Point : >410 F (210 C), Method: Open cup Ignition temperature : Remarks: not determined Lower explosion limit : Remarks: no data available Upper explosion limit : Remarks: no data available Fire Fighting Suitable : Carbon dioxide (CO 2 ), Dry powder, Foam, Alcohol-resistant foam, Water mist extinguishing media Unsuitable : Water extinguishing media Further information : In the event of fire, cool tanks with water spray. Protective equipment and precautions for firefighters Specific hazards : Burning produces noxious and toxic fumes. during fire fighting Special protective equipment for firefighters : In the event of fire, wear self-contained breathing apparatus. Use personal protective equipment. Section 6. Accidental Release Measures Personal precautions : Use personal protective equipment. Ensure adequate ventilation. Environmental precautions Methods for containment / Methods for cleaning up Additional advice : Should not be released into the environment. Do not contaminate water. Do not flush into surface water or sanitary sewer system. : Contain spillage, soak up with non-combustible absorbent material, (e.g. sand, earth, diatomaceous earth, vermiculite) and transfer to a container for disposal according to local / national regulations (see section 13). : Forms slippery/greasy layers with water. Section 7. Handling and Storage Handling Handling procedures Storage Requirements for storage areas and containers Other data Page 2 of 5 : Handle in accordance with good industrial hygiene and safety practice. Keep container closed when not in use. Do not use pressure to empty drums. Ensure all equipment is electrically grounded before beginning transfer operations. : Keep container tightly closed in a dry and well-ventilated place. : Stable under recommended storage conditions Ingersoll Rand # 10 Oil/Automotive Air Tool Lubricant MSDS

3 Section 8. Exposure Controls / Personal Protection Exposure Guidelines Contains no substances with occupational exposure limit values. Engineering measures Personal protective equipment Eye protection Hand protection Skin and body protection Respiratory protection Hygiene measures : Safety glasses with side-shields. Tightly fitting safety goggles : Neoprene gloves : Impervious clothing : Breathing apparatus needed only when aerosol or mist is formed. In case of vapour formation use a respirator with an approved filter. : Avoid contact with skin, eyes and clothing. Provide adequate ventilation. Do not breath dust or spray mist. Section 9. Physical and Chemical Properties Appearance Physical state : Liquid. Color : Amber. Odor : Mild. Safety Data Flash point : >410 F (210 C), Method: Open cup Ignition temperature : Remarks: not determined Lower explosion limit : Note: no data available Upper explosion limit : Note: no data available ph : Note: not applicable Vapour pressure : Note: no data available Density : g/cm 3 Water solubility : Note: slightly soluble Section 10. Stability and Reactivity Conditions to avoid : Remarks: Heat Materials to avoid : Remarks: Strong acids and strong bases Hazardous decomposition : Note: Carbon oxides products Hazardous reactions : Hazardous polymerisation does not occur. Section 11. Toxicological Information Acute inhalation toxicity Acute dermal toxicity Skin irritation Eye irritation Sensitisation Toxicology Assessment CMR effects Further information : Carcinogenicity: Not classified due lack of data. Mutagenicity: Not classified due lack of data. Reproductive toxicity: Not classified due lack of data. : There is no data available for this product. Ingersoll Rand # 10 Oil /Automotive Air Tool Lubricant MSDS Page 3 of 5

4 Section 12. Ecological Information Ecotoxicity effects Toxicity to fish : Remarks: no data available Toxicity to daphnia : Remarks: no data available and other aquatic invertebrates. Toxicity to algae : Remarks: no data available Elimination information (persistence and degradability) Bioaccumulation : Remarks: no data available Mobility : Remarks: no data available Biodegradability : Results: no data available Further information on ecology Exotoxicology Assessment Results of PBT assessment This substance is not considered to be persistent, bioaccumulating nor toxic (PBT). Additional ecological : There is no data available for this product. information Section 13. Disposal Considerations Further information Contaminated packaging : In accordance with local and national regulations. : Do not burn, or use a cutting torch on, the empty drum. Section 14. Transport Information DOT TDG IATA IMDG RID Section 15. Regulatory Information OSHA Hazards : This material is not hazardous under the criteria of the Federal OSHA Hazard Communication Standard 29CFR EPCRA - Emergency Planning Community Right - to - Know SARA 302 Reportable : Quantity California Prop. 65 Components : This product does not contain any chemicals known to State of California to cause cancer, birth defects, or any other reproductive harm. The components of this product are reported in the following inventories: TSCA : On TSCA Inventory DSL : All components of this product are on the Canadian DSL list. AICS NZIoC ENCS KECI PICCS IECSC CH INV : The formulation contains substances listed on the Swiss Inventory Page 4 of 5 Ingersoll Rand # 10 Oil/Automotive Air Tool Lubricant MSDS

5 Section 16. Other Information Further Information HMIS Classification : Health hazard: 1 Flammability: 1 Reactivity: 0 NFPA Classification : Health hazard: 1 Fire Hazard: 1 Reactivity: Notice to reader The information provided in this Safety Data Sheet is correct to the best of our knowledge, information and belief at the date of its publication. The information given is designed only as a guidance for safe handling, use, processing, storage, transportation, disposal and release and is not to be considered a warranty or quality specification. The information relates only to the specific material designated and may not be valid for such material used in combination with any other materials or in any process, unless specified in the text. Ingersoll Rand # 10 Oil /Automotive Air Tool Lubricant MSDS Page 5 of 5

6 Section 1. Product and Company Identification Material Safety Data Sheet Ingersoll Rand # 105 Grease Product Name : Ingersoll Rand # 105 Grease Product Use : Lubricant Validation Date : 04/26/2010 In Case of Emergency : TOOL HLP MSDS authored by: : Ingersoll Rand Industrial Technologies 800-A Beaty Street, P.O. Box 1600, Davidson, NC Emergency Overview : This product is a semi-solid that is insoluble in water. Direct eye contact may cause minor, short term irritation. Short term skin exposure is not expected to be irritating. Inhalation and ingestion are not anticipated routes of exposure during normal conditions of use. HMIS Rating : Flammability Health 1 1 Ingersoll Rand # 105 Grease /Automotive Air Tool Lubricant MSDS Page 1 of 4 0 PPE Reactivity Section 2. Composition, Information on Ingredients Components listed in this section may contribute to the potential hazards associated with exposure to the concentrate. The product may contain additional non-hazardous or trade-secret components. CAS Number Chemical Name Percentage Proprietary Mineral Oil <85% Exposure Limit ACGIH TLV: 5 mg/m 3 (as mist) ACGIH STEL: 10 mg/m 3 (as mist) OSHA PEL: 5 mg/m 3 (as mist) Proprietary Molybdenum Compounds <5% Exposure Limit ACGIH TLV: 10 mg/m 3 (inhalable); 3 mg/m 3 (resp.) (as insol moly) OSHA PEL: 15 mg/m 3 (as insoluble molybdenum) --- Carcinogenic Components : This product contains no carcinogens. Section 3. Hazards identification Potential Health Effects and Symptoms from Short term/acute Exposure Eye Exposure Skin Exposure Inhalation : This product is not expected to cause eye irritation under normal conditions of use. Symptoms of slight eye irritation may result when direct contact occurs, or when exposed to high mist levels in poorly ventilated areas. : Short term skin contact is not expected to cause skin irritation. Prolonged or repeated direct exposure to the skin may result in symptoms of irritation and redness. : This product has low volatility and so is not expected to cause respiratory tract irritation during normal conditions of use. Exposure to high mist levels in poorly ventilated areas may cause temporary irritation to the upper respiratory tract. : Ingestion may cause slight stomach irritation and discomfort. Ingestion Potential Chronic Health Effects Medical Conditions Aggravated by Exposure Carcinogenicity : This product is not listed as a known or suspected carcinogen by IARC, OSHA, or the NTP. ---

7 Section 4. First aid measures Eye contact Skin contact Inhalation Ingestion Notes to physician : Hold eyelids open and flush with a steady, gentle stream of water for at least 15 minutes. If symptoms persist, contact a physician. : Remove product from the skin by washing with a mild soap and water. Contaminated clothing should be removed to prevent prolonged exposure. If product is injected under the skin, seek treatment immediately. If symptoms of exposure persist, contact a physician. : If signs or symptoms of overexposure occur, remove the employee to fresh air. If symptoms persist, seek medical attention. : If ingested, dilute stomach contents with two glasses of milk or water. (NOTE: DO NOT give anything by mouth to an unconscious person.) Do not induce vomiting without medical supervision. If vomiting occurs spontaneously, keep airway clear. If symptoms of ingestion persist, seek medical attention. Section 5. Fire-fighting measures Fire and Explosive Properties Flashpoint : F COC Flammability Limits : LEL - N/A UEL - N/A Extinguishing Media: In accordance with NFPA guidance, dry chemical, foam, or CO 2 fire extinguishers are all acceptable. Note that while water fog extinguishers are also acceptable, do NOT apply a direct stream of water onto burning product because it may cause spreading and increase fire intensity. Unusual Fire & Explosion Hazards: Fire-Fighting Procedures and Equipment : Emergency responders in the danger area should wear bunker gear and self-contained breathing apparatus for fires beyond the incipient stage. See Section 8 of the MSDS for other PPE to be worn as conditions warrant. Section 6. Accidental release measures Clean-Up Measures : Important: As with any spill or leak, before responding ensure that you are familiar with the potential hazards and recommendations of the MSDS. Appropriate personal protective equipment must be worn. See Section 8 of this MSDS for PPE recommendations. If possible, safely contain the spill with dikes or other spill response equipment appropriate for petroleum or organic material releases. Take measures to prevent spreading of product. Note that while product will ignite it will not readily burn. However, as a precaution eliminate ignition sources. Prevent from entering sewers or waterways. Large volumes may be transferred to an appropriate container for proper disposal. Small volumes or residues may be soaked up with absorbents. Spill response material should be collected for proper disposal. Section 7. Handling and storage Handling Storage Special Comments Page 2 of 4 : As with any industrial chemical, handle the product in a manner that minimizes exposure to practicable levels. Prior to handling, consult Section 8 of this MSDS to evaluate personal protective equipment needs. Open containers slowly to relieve any pressure. Follow all other standard industrial hygiene practices. Empty containers may contain product residue. All safety precautions taken when handling this product should also be taken when handling empty drums and containers. Keep containers closed when not in use. Product residue in empty containers is combustible but will not readily burn. NOTE however, that excessive heating or cutting of empty containers may create an ignition source sufficient to start a fire and in extreme cases, cause an explosion. : Protect product quality by storing indoors and away from extreme temperatures. Close all containers when not in use. Ingersoll Rand # 105 Grease /Automotive Air Tool Lubricant MSDS

8 Section 8. Exposure controls/personal protection Personal Protective Equipment Eye Protection Skin Protection Respiratory Protection Engineering Controls: : Selection of personal protective equipment should be based upon the anticipated exposure and made in accordance with OSHA s Personal Protective Equipment Standard found in 29 CFR 1910 Subpart I. The following information may be used to assist in PPE selection. : Wear eye protection appropriate to prevent eye exposure. Where splashing is not likely, chemical safety glasses with side shields are recommended. Where splashing may occur, chemical goggles or full face shield is recommended. : Gloves are not normally needed during normal conditions of use. If health effects are experienced, oil or chemical resistant gloves such as butyl or nitrile are recommended. Where splashing or soaking is likely, wear oil or chemical resistant clothing to prevent exposure. : A respirator may be worn to reduce exposure to vapors, dust, or mist. Select a NIOSH/MSHA approved respirator appropriate for the type and physical character of the airborne material. A self-contained breathing apparatus is recommended in all situations where airborne contaminant concentration has not been confirmed to be below safe levels. Respirator use should comply with OSHA Respirator Protection Standard found in 29 CFR : Normal general ventilation is expected to be adequate. It is recommended that ventilation be designed in all instances to maintain airborne concentrations at lowest practicable levels. Ventilation should at a minimum, prevent airborne concentrations from exceeding any exposure limits listed in Section 2 of this MSDS. Section 9. Physical and chemical properties Physical Appearance : Black Odor : Mild Petroleum Physical State : Semi-Solid Water Solubility : Insoluble Specific Gravity :.920 Section 10. Stability and reactivity The user may wish to refer to 29 CFR (d)(2) and the ACGIH Threshold Limit Values for Chemical Substances and Physical Agents Biological Exposure Indicies (Appendix C) for the determination of exposure limits of mixtures. An industrial hygienist or similar professional may be consulted to confirm that the calculated exposure limits apply. Incompatibilities Decomposition Products may Include Conditions to Avoid Polymerization: Stability: : This product is incompatible with strong oxidizing agents. : Thermal decomposition products are dependent on combustion conditions. A complex mixture of airborne solid, liquid, particulates and gasses may evolve when the material burns. Combustion byproducts may include: oxides of carbon, oxides of molybdenum, incompletely burned hydrocarbons are fumes and smoke. : Avoid contact with incompatible materials and exposure to extreme temperatures. : This product is not expected to polymerize. : This product is stable. Section 11. Toxicological information Eye Effects: Skin Effects: Oral Effects: Inhalation Effects: Other : No further toxicological data known. : No further toxicological data known. : No further toxicological data known. : No further toxicological data known. Ingersoll Rand # 105 Grease /Automotive Air Tool Lubricant MSDS Page 3 of 4

9 Section 12. Ecological information Ecotoxicological Information Environmental Fate : This product has not been evaluated for ecotoxicity. As with any industrial chemical, exposure to the environment should be prevented and minimized wherever possible. : The degree of biodegradability and persistence of this product has not been determined. Section 13. Disposal considerations Waste disposal : Ensure that collection, transport, treatment, and disposal of waste product, containers and rinsate complies with all applicable laws and regulations. Note that use, mixture, processing, or contamination of the product may cause the material to be classified as a hazardous waste. It is the responsibility of the product user or owner to determine at the time of disposal, whether the product is regulated as a hazardous waste. Section 14. Transport information DOT Hazardous Material Information : * Not otherwise DOT regulated. Section 15. Regulatory information Federal Regulations Sara 313 Clean Water Act / Oil Pollution Act CERCLA Reportable Quantity Toxic Substances Control Act Ozone Depleting Substances Hazardous Air Pollutants: State Regulations: : This product contains NONE of the substances subject to the reporting requirements of Section 313 of Title I I I of the Superfund Amendments and Reauthorization Act of 1986 and 40 CFR Part 372. : This product contains mineral oil and is subject to regulation by Section 311 of the Clean Water Act and the Oil Pollution Act. Releases of the product into or leading to surface waters must be reported to the National Response Center at : Any components listed below have been assigned a reportable quantity (RQ) by the Federal EPA. Releases of the product into the environment that exceed the RQ for a particular component must be reported to the National Response Center at Component RQ * - * - * - * - * - * - * - * - * - * - * - * - * - * - * - * - * - * - * - * - * - * - * - : The components of this product are listed on the TSCA Inventory. : This product contains no ozone depleting substances as defined by the Clean Air Act. : Any components listed below are defined by the Federal EPA as hazardous air pollutants. Component RQ * - * - * - * - * - * - * - * - * - * - * - * - * - * - * - * - * - * - * - * - * - * - * - : This product contains mineral oil, and as used, may be regulated by state used oil regulations. Check with the appropriate state agency to determine whether such a regulation exists. No further data known. Section 16. Other information Prepared by : Corporate Regulatory Compliance Date of issue : 04/26/2010 Last Revision Date : 04/26/ R1 NOTICE: This MSDS provides a good faith representation of information believed to be accurate as of the last revision date. This document does not create any express or implied product warranties. Since conditions of use are beyond the control of Ingersoll Rand Company, all risks associated with product use are assumed by the user. Page 4 of 4 Ingersoll Rand # 105 Grease /Automotive Air Tool Lubricant MSDS