CommClean RUST REMOVER

Transcription

1 CommClean Rust Remover CommClean RUST REMOVER Commonwealth Oil's CommClean Rust Remover is a liquid rust remover designed for use on ferrous metals. CommClean Rust Remover can be used at temperatures of ambient to 55 C/130 o F depending upon the severity of rusting and process time. CommClean Rust Remover can be painted over without rinsing CommClean Rust Remover is best used at elevated temperatures. The higher the concentration and the temperature the faster acting the product will be. This is also dependent on the amount of rust to be removed. Temperature should not go above 55 C/130 F. CommClean Rust Remover will leave a light phosphate coat for in process rust protection. CommClean Rust Remover can be applied by spraying or soaking. CommClean Rust Remover is normally recommended at a 10:1dilution (10%) but may be used at varying concentrations depending on the soils being removed. CommClean Rust Remover is especially formulated to deliver the following benefits: Can be painted over without rinsing due to the phosphate coating that acts as a primer. Non-flammable and non-toxic. It will not release toxic fumes Useful on ferrous metal parts Will leave a light phosphate coating which allows for short term in-process corrosion inhibition. If temperature is above 55 C/130 F and/or the concentration is above 25% some types of paint may be removed. Page 1 of 7

2 Test CommClean Rust Remover Appearance Clear to pale yellow, odorless ph of Concentrate ph of 10% Dilution 6.3 Flash Point, COC None Density, lbs./us Gallon Specific Gravity 1.36 These are typical figures and do not constitute a specification. Handling & Safety Information For information on the safe handling and use of this product, refer to the Material Safety Data Sheet obtainable from Commonwealth Oil Corporation. For general safety, it is recommended that when handling an industrial grade cleaner, the operator should wear rubber gloves and splash goggles. Indoor storage, above freezing is preferred If frozen, allow to thaw and mix thoroughly Available in Pails, Drums and One-Way Bulk Containers Page 2 of 7

3 CommClean Rust Remover SECTION 1: Product Information and Company Identification Common Name : CommClean Rust Remover Product Code : 1286 Material Use : Rust Remover Supplier/Manufacturer : Commonwealth Oil, 2080 Ferriss Rd N., Harrow, ON, N0R 1G0 In Case of Emergency : CANUTEC (613) COLLECT 24 Hr SECTION 2: Composition, Information on Ingredients Component CAS Registry No. OSHA PEL ACGIH TLV Concentration % Phosphoric acid mg/m3 (in air) 3mg/m Tetrapotassium Pyrophosphate Sodium Iminodisuccinate Not Available Not Available Not Available Oral 2000mg/kg (rat) 5-10 See Section 8 for Exposure Limits. See Section 11 for Toxicological Data. SECTION 3: Hazards Identification Chemical Family : Complex Mixture Physical State : Liquid Emergency Overview : Use with care. Follow good Industrial Hygiene practices. Routes of Entry : Dermal contact, eye contact, inhalation and ingestion. Potential Acute Health Effects : No known significant effects or critical hazards. Potential Chronic Health Effects : Not applicable for carcinogenic, mutagenic, or teratogenic effects. Medical Conditions Aggravated by : Repeated or prolonged exposure is not known to aggravate Overexposure medical condition. Overexposure Signs and Symptoms : Not available See Toxicological Information (section 11) SECTION 4: First Aid Measures Eye Contact Skin Contact Inhalation Ingestion Notes to Physician : Check for and remove any contact lenses. In case of contact, immediately flush eyes with plenty of water for at least 20 minutes. Cold water may be used. Get medical attention if irritation occurs and or persists. : Remove any contaminated clothing. Wash with soap and water. Get medical attention if irritation occurs and or persists. : If inhaled, remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. Get medical attention. : Do not induce vomiting unless directed to do so by medical personnel. Never give anything by mouth to an unconscious patient. If large amounts of this material are swallowed, call a physician immediately. : Not available Page 3 of 7

4 SECTION 5: Fire Fighting Measures Flammability of the Product : Low hazard. May be combustible or burn at high temperatures where the water has evaporated. Auto Ignition Temperature : N/A Flash Point (COC) : N/A Flammable Limits Hazardous Combustion : Fumes, smoke, and carbon monoxide in case of incomplete combustion. Products Thermal decomposition products may be toxic and may include hydrogen, phosphine, oxides of phosphorus and irritating gases. Fire Hazards in Presence : Possibly flammable once water content has evaporated. of various Substances Explosion Hazard in Presence: Risks of explosion of the product in presence of mechanical impact: Not available. of various substances Risks of explosion of the product in presence of static discharge: Not available. Fire Fighting Media : SMALL FIRE: Use dry chemical powder and Instructions LARGE FIRE: Use water spray, fog or foam. Do not use water jet. Protective Clothing (Fire) : Fire fighters should wear positive pressure self-contained breathing apparatus (SCBA) and full turnout gear. Be sure to use a MSHA/NIOSH approved respirator or equivalent. Special Remarks on : Do not use forced stream as this could cause fire to spread. Self-contained breathing Fire Hazards apparatus should be worn by fire fighters. SECTION 6: Accidental Release Measures Small Spill and Leak : Absorb with an inert material and put spilled material in an appropriate waste disposal. Large Spill and Leak : Absorb with an inert material and put spilled material in an appropriate waste disposal. Do not allow any potentially contaminated water including rainwater, runoff from fire fighting or spills enter any waterway, sewer or drain. Note: See section 8 for personal protective equipment and section 13 for waste disposal. SECTION 7: Handling and Storage Handling Storage : After handling, always wash hands thoroughly with soap and water. Do not cut, weld, heat or pressurize containers. Use with adequate ventilation. : Keep container tightly closed. Store in a dry, cool and well-ventilated area. Do not cut, weld, heat or pressurize empty containers. Do not store near open flames or sources of ignition. SECTION 8: Exposure Controls, Personal Protection Engineering Controls : Good general ventilation should be sufficient to control airborne levels. Local exhaust is recommended to control emissions at the source. Mechanical ventilation is recommended for confined areas. Ensure eyewash stations and safety showers are proximal to the work station location. Personal Protection Eyes : Safety glasses or goggles are advisable. Body : Lab coat or suitable protective clothing is advisable. Respiratory : A respirator is not needed under normal and intended usage conditions. Hands : Chemical resistant or oil impervious gloves are advisable. Feet : Shoes (as required by the work place). Personal Protection in Case : Splash goggles. Full suit. Vapor respirator. Boots. Chemical resistant gloves. A self of a Large Spill contained breathing apparatus should be used to avoid inhalation of the product. Consult local authorities for your acceptable Exposure Limits : ACGIH TLV (United States and Canada) Page 4 of 7

5 CommClean RUST REMOVER SECTION 9: Physical and Chemical Properties Physical State : Liquid Appearance and Colour : Clear to pale yellow solution. Odour : Mild odour. ph : > 6.0 Flash Point (COC) : N/A Boiling/Condensation Point : > 100 C (> 212 F) Pour Point C ( F) : > 0 C (< 32 F) Freezing Point : < 0 C (< 32 F) Specific Gravity : 1.36 (Water = 1) Density, lbs./gallon : Vapor Density % Volatility, By volume Evaporation Rate : Equal to water VOC : N/A Viscosity 40 C Solubility in Water : Soluble SECTION 10: Stability and Reactivity Stability and Reactivity Incompatibility with Various Substances Hazardous Decomposition Products Hazardous Polymerization SECTION 11: Toxicological Information Acute Toxicity Data : The product is stable. : Strong oxidizers. Reducing agents. Strong bases. Combustibles. : Fumes, smoke, and carbon monoxide in case of incomplete combustion. Thermal decomposition products may be toxic and may include hydrogen, phosphine, oxides of phosphorus and irritating gases. : Should not occur : Avoid breathing mist and fumes. Proper ventilation should be utilized. Chronic Effects on Humans: Eyes : Slightly irritating, but will not injure eye tissue in diluted form. Skin : Low toxicity. Frequent or prolonged contact may irritate the skin. Ingestion : Low toxicity in diluted form. Inhalation : Negligible hazard at normal temperatures. Elevated temperatures or mechanical action may form vapors, mists or fumes, which may be irritating to the eyes, nose, throat and lungs. Avoid breathing vapors or mists. Other Toxic Effects on Humans : Low Special Remarks on Toxicity : Low to Animals Special Remarks on Other Toxic : None reported. Effects on Humans SECTION 12: Ecological Information BOD and COD Biodegradability/OECD Mobility Products of Degradation Toxicity of the Products of Biodegradation Special Remarks on the Products of Biodegradation Page 5 of 7

6 SECTION 13: Disposal Considerations Waste Information : Waste should be disposed of in accordance to local, federal and state environmental control regulations. Consult your local or regional authorities. SECTION 14: Transport Information Regulatory Information UN Number Proper Shipping Name United States (DOT) 1760 Corrosive Liquid N.O.S. Canada (TDG) 1760 Corrosive liquid N.O.S. Mexico (NOM-004-SCT2-1994) 1760 Corrosive liquid N.O.S. IMDG Code 1760 Corrosive liquid N.O.S. IATADGR Class 1760 Corrosive liquid N.O.S. NAERG (North American Emergency Response Guide): 154 Class Packing Group Label Additional Information SECTION 15: Regulatory Information United States U.S. Federal Regulations State Regulations Canada WHMIS (Canada) : TSCA 8(b) inventory: All components listed. SARA 302/304/311/312 extremely hazardous substances: No products found. SARA 302/304 emergency planning and notification: No products found. SARA 302/304/311/312 hazardous chemicals: No products found. SARA 311/312 MSDS distribution chemical inventory hazard identification: No products found. : California prop. 65: No products found. Class E, D2B CEPA DSL: All components listed. "This product has been classified in accordance with the hazard criteria of the Controlled Products Regulations and the MSDS contains all of the information required by the Controlled Products Regulations." 1 0 Mexico Flammability: 0 Classification : Health: 1 Reactivity: 0 Special: 0 Page 6 of 7

7 SECTION 16: Other Information Label Requirements : USE WITH CARE. USE AS DIRECTED. Hazardous Material Information System (U.S.A.) : Health 1 Fire Hazard 0 Reactivity 0 Personal B Protection National Fire Protection Association (U.S.A.) : 0 Flammability: 0 Health: 1 0 Instability: 0 Special Date of Issue : Date of Previous Issue : September 27, 2010 Notice to reader To the best of our knowledge, the information contained herein is accurate. However, neither the above named supplier nor any of its subsidiaries assumes any liability whatsoever for the accuracy of completeness of the information contained herein. Final determination of suitability of any material is the sole responsibility of the user. All materials may present unknown hazards and should be used with caution. Although certain hazards are described herein, we cannot guarantee that these are the only hazards that exist. Authored By: Commonwealth Oil Technical Services Department (Tel: ) Page 7 of 7