Stone & Tile Care Resource Guide

Size: px
Start display at page:

Download "Stone & Tile Care Resource Guide"

Transcription

1 2006/2007 EDITION 2005/2006 EDITION Stone & Tile Care Resource Guide Interactive CD To jump directly to a specific topic: 1 Click on the topic title on the Table of Contents page. 2 Alternatively, the Bookmarks and Pages tabs can be used to browse through the pages quickly. KEEPING STONE & TILE BEAUTIFUL

2 Table of Contents CARE INSTRUCTIONS BY SURFACE TYPE Marble Granite Limestone Travertine Polished Marble Unpolished, Honed & Textured Marble Polished Terrazzo & Agglomerate Marble Less Absorptive Polished Granite (Homogenous Granite) More Absorptive Polished Granite (Oriented & Veined Granite) Unpolished, Honed & Textured Granite (Homogenous, Veined & Oriented Granite) Polished Limestone Unpolished, Honed & Textured Limestone Polished Travertine Unpolished, Honed & Textured Travertine Slate Sandstone & Flagstone Terra Cotta & Clay Products Concrete & Masonry Natural Slate Sandstone & Flagstone Saltillo, Terra Cotta & Clay Brick Concrete, Stucco & Cementitious Brick Ceramic & Porcelain Tile Ceramic, Porcelain & Quarry Tile with Cement-based Grout Ceramic, Porcelain & Quarry Tile with Epoxy-based Grout Other 33 Cantera & Adoquin TECHNICAL DATA SHEET (TDS) Protect Clean Transform BulletProof Sealer Heavy Duty Sealer Sealer Heavy Duty Exterior Sealer Grout Sealer Impregnator Pro Sealer Grout Release Revitalizer Cleaner & Protector Stone & Tile Cleaner KlenzAll Restore Oil Stain Remover Polish Enhancer Pro Enhancer High Gloss Lacquer Honing Powder Polishing Powder Shining Powder Copyright DuPont. All Rights Reserved. StoneTech Logo, StoneTech, BulletProof, Impregnator Pro, Revitalizer, DuPont Oval Logo and DuPont are trademarks or registered trademarks of DuPont.

3 Polished Marble READ ALL INSTRUCTIONS AND PRODUCT LABELS COMPLETELY BEFORE USING Pretest in an inconspicuous area prior to application to determine if the desired results will be achieved and that the stone is not adversely affected. NEW INSTALLATIONS Follow the recommended installation methods and procedures of the Marble Institute of America and the Tile Contractors Association. RESTORATIVE CLEANING Depending on the type of soil, stain or other foreign matter present, select one or more of the following options: For stripping off any existing topical acrylic, urethane, epoxy, heavy wax coatings and epoxy grout haze: 3 For heavy, hard to remove coatings, use a commercially available coating stripper. Follow instructions as indicated on bottle. For cleaning of grease, oil, dirt, dry soil and soap scum: 3 Strip off all topical finishes such as waxes and coatings. 4 Prepare a solution of StoneTech Professional KlenzAll mixed with warm or hot water as suggested below: Medium Duty Usage Mix 1 part of KlenzAll to 4 parts of water. Heavy Duty Usage Mix 1 part KlenzAll to 2 parts of water. 5 Apply KlenzAll using a low-pressure chemical-resistant sprayer, sponge or mop. 6 Agitate well using a stiff nylon bristle scrub brush, stiff bristle push broom or a weighted floor machine at 130 lbs.-140 lbs., 175 rpm, fitted with a scrub brush attachment. 7 Rinse well with clean water and mop, sponge or wet vacuum to remove the remaining cleaning solution. A hard surface extraction wand and portable or truck mounted extraction machine may be used. Repeat the rinsing and wet vacuum process to insure that all dirt, soil and cleaner residue have been removed. 8 To remove deep or stubborn oil stains not completely removed by KlenzAll, let the surface dry and use StoneTech Professional Oil Stain Remover. 9 Apply a ¼ inch thick coat of Oil Stain Remover to the oil stained area. Insure that Oil Stain Remover covers an area 1 to 2 beyond the stained area for the purpose of containment. a Allow 2-3 days for the Oil Stain Remover to dry to a powder. b Sweep and wipe up dried powder and evaluate the stained area for removal. c Repeat process if needed. d Remove any remaining Oil Stain Remover using mineral spirits. MECHANICAL REFINISHING OF POLISHED MARBLE For scratch, etch and wear pattern removal and to restore the surface to an even finish. Depending on the severity of the damage to the stone and/or the desired surface appearance, choose one or more of the grit levels of the StoneTech Professional Honing Powders 180/280/400/600/800, StoneTech Professional Polishing Powder and/or StoneTech Professional Shining Powder as appropriate. For refinishing to a honed finish: overspray onto surfaces not intended to be 3 Strip off all topical finishes such as waxes and coatings. 4 Liberally apply Honing Powder to the stone surface. 5 Add water to form a milk-like consistency. 6 Refinish using a hand orbital sander or weighted floor machine at 130 lbs.-140 lbs., 175 rpm, fitted with a natural hair pad. 7 Keep compound wet with plenty of water while refinishing. Add Honing Powder as needed. 8 Refinish area until the desired level of hone has been achieved. 9 Rinse well and use a wet vacuum to remove all excess compound. 10 Clean equipment with water. For refinishing to a polish: Use successively higher grits of Honing Powder to close the face of the stone. Follow with Polishing Powder as applicable. 3 Strip off all topical finishes such as waxes and coatings. 4 Liberally apply Polishing Powder to the stone surface. 5 Add water to form a milk-like consistency. 6 Refinish using a hand orbital sander or weighted floor machine at 130 lbs.-140 lbs., 175 rpm, fitted with a natural hair pad. Care Instructions 7 Keep compound wet with plenty of water while refinishing. Add Polishing Powder as needed. 8 Refinish area until the desired level of polish has been achieved. 9 Rinse well and use a wet vacuum to remove all excess compound. 10 Clean equipment with water. 11 For a highly polished finish: 12 Use Shining Powder as applicable. See Maintenance Polishing. SEALING & PROTECTING Natural stone surfaces must be sealed to prevent or minimize staining. Leaving natural stone untreated may greatly hinder the complete removal of stains in the future. The following suggestions are for impregnating the stone and will allow the stone to breathe. Allow new installations to cure for 72 hours prior to applying sealer. For a natural looking protector on interior and exterior surfaces (heavy duty protection, water and oil repellency): Option 1: Heavy duty protection, water-based formula: overspray onto surfaces not intended to be 3 Insure that surface is clean and residue-free. 4 StoneTech Professional Heavy Duty Sealer may be applied to damp surfaces one hour after standing water has been removed. 5 Liberally apply an even coat of sealer using a paint pad, low-pressure chemical-resistant sprayer, roller or brush. 6 Allow sealer to penetrate the surface for minutes. During this time, distribute excess over entire area to insure even penetration. Wipe off any remaining sealer prior to drying on the surface. 7 A second coat may be needed for porous, absorbent surfaces and should be applied minutes after initial application as directed in steps A minimum of 15 minutes after final application, wipe entire surface with a clean dry towel to remove any residue and excess sealer, if needed. 9 If sealer was not completely wiped off and a residue appears, wipe entire surface with a towel dampened with sealer. Use a white, 10 A full cure is achieved after hours; foot 11 Expected coverage is 800-1,200 sq. ft. per MARBLE GRANITE LIMESTONE TRAVERTINE SLATE StoneTech ProfessioNAL Stone & TILE CARE RESOURCE GUIDE /2007 Edition STONEHELP ( ) 01

4 MARBLE GRANITE LIMESTONE TRAVERTINE SLATE 12 Re-application of Heavy Duty Sealer: A 1-3 year re-application is needed for exterior surfaces. Option 2: Heavy duty protection, solventbased formula: 3 Insure that surface is clean, dry and residuefree. 4 Ensure area is well-ventilated. Use a respirator if unsure that work area is well-ventilated. A NIOSH approved respirator with a combination HEPA/organic vapor cartridge is recommended. Follow respirator manufacturer s instructions for use. 5 Liberally apply an even coat of StoneTech Professional Impregnator Pro Sealer using a paint pad, roller, brush or pump-up garden sprayer. DO NOT USE A POWER SPRAYER. 6 Allow sealer to penetrate the surface for minutes; denser material may require more time for sealer to penetrate. During this time, distribute excess over entire area to insure even penetration. Wipe off any remaining sealer prior to drying on the surface. 7 A second coat may be needed for porous, absorbent surfaces and should be applied one hour after initial application as directed in steps If sealer was not completely wiped off and a residue appears, wipe entire surface with a towel dampened with sealer. Use a white, 9 A full cure is achieved after hours; foot 10 Expected coverage is 800-1,200 sq. ft. per 11 Re-application of Impregnator Pro Sealer: A 1-3 year re-application is needed for exterior surfaces. WARNING: HARMFUL VAPORS. HARMFUL OR FATAL IF SWALLOWED. COMBUSTIBLE. KEEP OUT OF THE REACH OF CHILDREN. Do not ingest. Avoid contact with eyes and skin. Avoid exposure to vapors. Use in a well-ventilated area. For spray application: Use a pump-up garden sprayer. DO NOT USE A POWER SPRAYER. Use a respirator if unsure that work area is wellventilated. A NIOSH approved respirator with a combination HEPA/organic vapor cartridge is recommended. Follow respirator manufacturer s instructions for use. Do not freeze or store above 100 F/38 C. Do not mix with other chemicals. For a natural looking protector on exterior surfaces (heavy duty protection, water repellency only): StoneTech Professional Heavy Duty Exterior Sealer is a water repellent specially designed for exterior projects such as facades, cladding, pool decks, parking areas and driveways. It is very resistant to chemicals (i.e., chlorine) and to the effects of weather (i.e., ultraviolet light/sunlight, driving water/rain). overspray onto surfaces not intended to be 3 Insure that the surface is clean, dry and residue-free. 4 Liberally apply an even coat of Heavy Duty Exterior Sealer with a paint pad, brush, paint roller or low-pressure solvent-resistant sprayer. 5 Allow sealer to penetrate the surface for 5-15 minutes; denser material may require more time for sealer to penetrate. During this time, distribute excess over entire area to insure even penetration. Wipe off any remaining sealer prior to drying on the surface. 6 A second coat may be needed for porous, absorbent surfaces and should be applied one hour after initial application as directed in steps If sealer was not completely wiped off and a residue appears, wipe entire surface with a towel dampened with sealer. Use a white, 8 Do not walk on surface for at least 4-6 hours. Full cure is achieved in hours. 9 Expected coverage is 800-1,200 sq. ft. per 10 Re-application of Heavy Duty Exterior Sealer: A 5-10 year re-application is recommended for exterior surfaces. MAINTENANCE CLEANING Highly alkaline, acidic, ammoniated, abrasive cleaners and/or bleach may break down the sealer, adversely affecting repellency and may not be good for the stone. Use a neutral cleaner specially formulated for natural stone. For routine cleaning with protection: Revitalizer Cleaner & Protector concentrate mixed with warm or hot water as suggested below: Light Duty Usage 1 part Revitalizer Cleaner & Protector to 4 parts water. Medium Duty Usage/Spray Refill 1 part Revitalizer Cleaner & Protector to 1 part water. (One gallon of concentrate makes up to five gallons of ready-to-use solution.) 3 Apply the Revitalizer Cleaner & Protector solution using a low-pressure chemicalresistant sprayer, mop, sponge or automatic scrubbing machine. 4 No rinsing needed. 5 Or use Revitalizer Cleaner & Protector in a ready-to-use spray bottle or wipes. For routine maintenance cleaning: Stone & Tile Cleaner concentrate mixed with warm or hot water as suggested below: 2 ounces Stone & Tile Cleaner in 1 gallon of water. (Do not mix stronger than 2 ounces to a gallon as a maintenance cleaner. One gallon of concentrate makes 65 gallons of cleaning solution.) 3 Apply the solution using a sponge, mop or automatic scrubbing machine, then wipe or rinse off. 4 Or use Stone & Tile Cleaner in a ready-to-use spray bottle or wipes. MAINTENANCE POLISHING To maintain the shine and beauty of polished marble on a routine basis and to minimize the need for restorative polishing: 3 Liberally apply Shining Powder to the surface. 4 Add enough water to form a milk-like consistency. 5 Refinish using a hand orbital sander or weighted floor machine at 130 lbs lbs., 175 rpm, fitted with a natural hair pad. 6 Rinse well and use a wet vacuum to remove all remaining compound. 7 Expected coverage is 1,000-1,700 sq. ft. per 1.5 lb. canister. 8 Re-application: Semi-annually or as needed. For a brilliant shine on countertops, vanities and vertical surfaces: 1 On a cleaned surface, spray a light coat of StoneTech Professional Polish over the entire surface. Do not spray in eyes. 2 Spread the polish evenly with a clean, white terry cloth towel. 3 Buff off polish. Keep turning the towel to insure that a clean section is being used for maximum efficiency. 4 Continue buffing until there is no visible polish left and high shine appears. 5 Reapplication as desired. Note: Polish will work best on stone previously sealed with StoneTech Professional sealers. 02

5 Unpolished, Honed & Textured Marble READ ALL INSTRUCTIONS AND PRODUCT LABELS COMPLETELY BEFORE USING Pretest in an inconspicuous area prior to application to determine if the desired results will be achieved and that the stone is not adversely affected. NEW INSTALLATIONS Follow the recommended installation methods and procedures of the Marble Institute of America and the Tile Contractors Association. PRE-GROUTING For making grout clean up easier on porous stone: 2 Insure that surface temperature of the stone is between 50-80ºF. 3 Apply a single coat of StoneTech Professional Grout Release using a paint pad, low-pressure chemical-resistant sprayer, roller or brush. 4 Allow the Grout Release to completely penetrate the stone for 5-15 minutes. 5 Wipe up all remaining sealer from the surface of the stone. Do not allow pooling or sealer to dry on the surface. Do not over apply. 6 Allow for a minimum of 4 hours cure time prior to grouting. 7 After grouting, remove excess grout. Do not allow grout to completely dry prior to removal. 8 Expected coverage for Grout Release is sq. ft. per RESTORATIVE CLEANING Depending on the type of soil, stain or other foreign matter present, select one or more of the following options: For stripping off any existing topical acrylic, urethane, epoxy, heavy wax coatings and epoxy grout haze: 3 For heavy, hard to remove coatings, use a commercially available coating stripper. Follow instructions as indicated on bottle. For cleaning of grease, oil, dirt, dry soil and soap scum: 3 Strip off all topical finishes such as waxes and coatings. 4 Prepare a solution of StoneTech Professional KlenzAll mixed with warm or hot water as suggested below: Medium Duty Usage Mix 1 part of KlenzAll to 4 parts of water. Heavy Duty Usage Mix 1 part KlenzAll to 2 parts of water. 5 Apply KlenzAll using a low-pressure chemical-resistant sprayer, sponge or mop. 6 Agitate well using a stiff nylon bristle scrub brush, stiff bristle push broom or a weighted floor machine at 130 lbs.-140 lbs., 175 rpm, fitted with a scrub brush attachment. 7 Rinse well with clean water and mop, sponge or wet vacuum to remove the remaining cleaning solution. A hard surface extraction wand and portable or truck mounted extraction machine may be used. Repeat the rinsing and wet vacuum process to insure that all dirt, soil and cleaner residue have been removed. 8 To remove deep or stubborn oil stains not completely removed by KlenzAll, let the surface dry and use StoneTech Professional Oil Stain Remover. a Apply a ¼ inch thick coat of Oil Stain Remover to the oil stained area. Insure that Oil Stain Remover covers an area 1 to 2 beyond the stained area for the purpose of containment. b Allow 2-3 days for the Oil Stain Remover to dry to a powder. c Sweep and wipe up dried powder and evaluate the stained area for removal. d Repeat process if needed. e Remove any remaining Oil Stain Remover using mineral spirits. MECHANICAL REFINISHING OF HONED MARBLE For scratch, etch, wear pattern removal and to restore the surface to an even finish. Depending on the severity of the damage to the stone and/or the desired surface appearance, choose one or more of the grit levels of the StoneTech Professional Honing Powders 180/280/400/600/800. For refinishing to a honed finish: 3 Strip off all topical finishes such as waxes and coatings. 4 Liberally apply Honing Powder to the stone surface. 5 Add water to form a milk-like consistency. 6 Refinish using a hand orbital sander or weighted floor machine at 130 lbs.-140 lbs., 175 rpm, fitted with a natural hair pad. 7 Keep compound wet with plenty of water while refinishing. Add Honing Powder as needed. 8 Refinish area until the desired level of hone has been achieved. 9 Rinse well and use a wet vacuum to remove all compound. 10 Clean equipment with water. SEALING & PROTECTING Natural stone surfaces must be sealed to prevent or minimize staining. Leaving natural stone untreated may greatly hinder the complete removal of stains in the future. The following suggestions are for impregnating the stone and will allow the stone to breathe. Allow new installations to cure for 72 hours prior to applying sealer. Care Instructions For a natural looking protector on interior and exterior surfaces (heavy duty protection, water and oil repellency): Option 1: Heavy duty protection, water-based formula: 3 Insure that surface is clean and residue-free. 4 StoneTech Professional Heavy Duty Sealer may be applied to damp surfaces one hour after standing water has been removed. 5 Liberally apply an even coat of sealer using a paint pad, low-pressure chemical-resistant sprayer, roller or brush. 6 Allow sealer to penetrate the surface for minutes. During this time, distribute excess over entire area to insure even penetration. Wipe off any remaining sealer prior to drying on the surface. 7 A second coat may be needed for porous, absorbent surfaces and should be applied minutes after initial application as directed in steps A minimum of 15 minutes after final application, wipe entire surface with a clean dry towel to remove any residue and excess sealer, if needed. 9 If sealer was not completely wiped off and a residue appears, wipe entire surface with a towel dampened with sealer. Use a white, 10 A full cure is achieved after hours; foot 11 Expected coverage is 600-1,000 sq. ft. per 12 Re-application of Heavy Duty Sealer: A 1-3 year re-application is needed for exterior surfaces. Option 2: Heavy duty protection, solventbased formula: 3 Insure that surface is clean, dry and residuefree. 4 Ensure area is well-ventilated. Use a respirator if unsure that work area is well-ventilated. A NIOSH approved respirator with a combination HEPA/organic vapor cartridge is recommended. Follow respirator manufacturer s instructions for use. 5 Liberally apply an even coat of StoneTech Professional Impregnator Pro Sealer using a paint pad, roller, brush or pump-up garden sprayer. DO NOT USE A POWER SPRAYER. 6 Allow sealer to penetrate the surface for minutes; denser material may require more StoneTech ProfessioNAL Stone & TILE CARE RESOURCE GUIDE /2007 Edition STONEHELP ( ) MARBLE GRANITE LIMESTONE TRAVERTINE SLATE 03

6 MARBLE GRANITE LIMESTONE TRAVERTINE SLATE time for sealer to penetrate. During this time, distribute excess over entire area to insure even penetration. Wipe off any remaining sealer prior to drying on the surface. 7 A second coat may be needed for porous, absorbent surfaces and should be applied one hour after initial application as directed in steps If sealer was not completely wiped off and a residue appears, wipe entire surface with a towel dampened with sealer. Use a white, 9 A full cure is achieved after hours; foot 10 Expected coverage is 600-1,000 sq. ft. per 11 Re-application of Impregnator Pro Sealer: A 1-3 year re-application is needed for exterior surfaces. WARNING: HARMFUL VAPORS. HARMFUL OR FATAL IF SWALLOWED. COMBUSTIBLE. KEEP OUT OF THE REACH OF CHILDREN. Do not ingest. Avoid contact with eyes and skin. Avoid exposure to vapors. Use in a well-ventilated rea. For spray application: Use a pump-up garden sprayer. DO NOT USE A POWER SPRAYER. Use a respirator if unsure that work area is wellventilated. A NIOSH approved respirator with a combination HEPA/organic vapor cartridge is recommended. Follow respirator manufacturer s instructions for use. Do not freeze or store above 100 F/38 C. Do not mix with other chemicals. For a natural looking protector on exterior surfaces (heavy duty protection, water repellency only): StoneTech Professional Heavy Duty Exterior Sealer is a water repellent specially designed for exterior projects such as facades, cladding, pool decks, parking areas and driveways. It is very resistant to chemicals (i.e., chlorine) and to the effects of weather (i.e., ultraviolet light/sunlight, driving water/rain). 3 Insure that the surface is clean, dry and residue-free. 4 Liberally apply an even coat of Heavy Duty Exterior Sealer with a paint pad, brush, paint roller or low-pressure solvent-resistant sprayer. 5 Allow sealer to penetrate the surface for 5-15 minutes; denser material may require more time for sealer to penetrate. During this time, distribute excess over entire area to insure even penetration. Wipe off any remaining sealer prior to drying on the surface. 6 A second coat may be needed for porous, absorbent surfaces and should be applied one hour after initial application as directed in steps If sealer was not completely wiped off and a residue appears, wipe entire surface with a towel dampened with sealer. Use a white, 8 Do not walk on surface for at least 4-6 hours. Full cure is achieved in hours. 9 Expected coverage is sq. ft. per 10 Re-application of Heavy Duty Exterior Sealer: A 5-10 year re-application is recommended for exterior surfaces. WARNING: Avoid exposure to vapors. Use in For a color enhancing, impregnating (non-topical) protector on interior and exterior surfaces (heavy duty protection, water and oil repellency): 3 Insure that surface is clean, dry and residuefree. Surface temperature should be between 50 F and 80 F. 4 Liberally apply an even coat of StoneTech Professional Enhancer Pro using a paint pad, roller, brush or low-pressure solvent-resistant sprayer. 5 Allow to penetrate the surface for minutes; denser material may require more time for Enhancer Pro to penetrate. During this time, distribute excess over entire area to insure even penetration. Completely wipe surface with a clean dry terrycloth towel. DO NOT ALLOW ENHANCER PRO TO DRY COMPLETELY ON SURFACE! Failure to remove enhancer from the surface may result in a film or residue that may need to be mechanically removed. 6 A second coat may be needed for porous, absorbent surfaces or if a darker appearance is required and should be applied one hour after initial application as directed in steps If sealer was not completely wiped off and a residue appears, wipe entire surface with a towel dampened with sealer. Use a white, 8 A full cure is achieved after hours; foot 9 Expected coverage is sq. ft. per 10 Re-application of Enhancer Pro : interior or exterior surfaces. WARNING: HARMFUL VAPORS. HARMFUL OR FATAL IF SWALLOWED. COMBUSTIBLE. KEEP OUT OF THE REACH OF CHILDREN. Do not ingest. Avoid contact with eyes and skin. Avoid exposure to vapors. Use in a well-ventilated rea. For spray application: Use a pump-up garden sprayer. DO NOT USE A POWER SPRAYER. Use a respirator if unsure that work area is wellventilated. A NIOSH approved respirator with a combination HEPA/organic vapor cartridge is recommended. Follow respirator manufacturer s instructions for use. Do not freeze or store above 100 F/38 C. Do not mix with other chemicals. For a color enhancing, impregnating (non-topical) protector on interior surfaces (economical protection, water and oil repellency): Insure that surface is clean, dry and residue-free. 3 Liberally apply an even coat of StoneTech Professional Enhancer using a paint pad, low-pressure chemical-resistant sprayer, roller or brush. 4 Allow to penetrate the surface for minutes; denser material may require maximum time for enhancer to penetrate. During this time, distribute excess over entire area to insure even penetration. Completely wipe surface dry. DO NOT ALLOW ENHANCER TO DRY COMPLETELY ON SURFACE! 5 A second coat may be needed for porous, absorbent surfaces or if a darker appearance is required and should be applied one hour after initial application as directed in steps If sealer was not completely wiped off and a residue appears, wipe entire surface with 7 A full cure is achieved after hours; foot 8 Expected coverage is sq. ft. per 9 Re-application of Enhancer: MAINTENANCE CLEANING Highly alkaline, acidic, ammoniated, abrasive cleaners and/or bleach may break down the sealer, adversely affecting repellency and may not be good for the stone. Use a neutral cleaner specially formulated for natural stone. For routine cleaning with protection: Revitalizer Cleaner & Protector concentrate mixed with warm or hot water as suggested below: Light Duty Usage 1 part Revitalizer Cleaner & Protector to 4 parts water. Medium Duty Usage/Spray Refill 1 part Revitalizer Cleaner & Protector to 1 part water. (One gallon of concentrate makes up to five gallons of ready-to-use solution.) 3 Apply the Revitalizer Cleaner & Protector solution using a low-pressure chemicalresistant sprayer, mop, sponge or automatic scrubbing machine. 4 No rinsing needed. 5 Or use Revitalizer Cleaner & Protector in a ready-to-use spray bottle or wipes. For routine maintenance cleaning: Stone & Tile Cleaner concentrate mixed with warm or hot water as suggested below: 2 ounces Stone & Tile Cleaner in 1 gallon of water. (Do not mix stronger than 2 ounces to a gallon as a maintenance cleaner. One gallon of concentrate makes 65 gallons of cleaning solution.) 3 Apply the solution using a sponge, mop or automatic scrubbing machine, then wipe or rinse off. 4 Or use Stone & Tile Cleaner in a ready-to-use spray bottle or wipes. 04

7 Polished Terrazzo & Agglomerate Marble READ ALL INSTRUCTIONS AND PRODUCT LABELS COMPLETELY BEFORE USING Pretest in an inconspicuous area prior to application to determine if the desired results will be achieved and that the stone is not adversely affected. NEW INSTALLATIONS Follow the recommended installation methods and procedures of the Marble Institute of America and the Tile Contractors Association. RESTORATIVE CLEANING Depending on the type of soil, stain or other foreign matter present, select one or more of the following options: For stripping off any existing topical acrylic, urethane, epoxy, heavy wax coatings and epoxy grout haze: 3 For heavy, hard to remove coatings, use a commercially available coating stripper. Follow instructions as indicated on bottle. For cleaning of grease, oil, dirt, dry soil and soap scum: 3 Strip off all topical finishes such as waxes and coatings. 4 Prepare a solution of StoneTech Professional KlenzAll mixed with warm or hot water as suggested below: Medium Duty Usage Mix 1 part of KlenzAll to 4 parts of water. Heavy Duty Usage Mix 1 part KlenzAll to 2 parts of water. 5 Apply KlenzAll using a low-pressure chemical-resistant sprayer, sponge or mop. 6 Agitate well using a stiff nylon bristle scrub brush, stiff bristle push broom or a weighted floor machine at 130 lbs.-140 lbs., 175 rpm, fitted with a scrub brush attachment. 7 Rinse well with clean water and mop, sponge or wet vacuum to remove the remaining cleaning solution. A hard surface extraction wand and portable or truck mounted extraction machine may be used. Repeat the rinsing and wet vacuum process to insure that all dirt, soil and cleaner residue have been removed. 8 To remove deep or stubborn oil stains not completely removed by KlenzAll, let the surface dry and use StoneTech Professional Oil Stain Remover. a Apply a ¼ inch thick coat of Oil Stain Remover to the oil stained area. Insure that Oil Stain Remover covers an area 1 to 2 beyond the stained area for the purpose of containment. b Allow 2-3 days for the Oil Stain Remover to dry to a powder. c Sweep and wipe up dried powder and evaluate the stained area for removal. d Repeat process if needed. e Remove any remaining Oil Stain Remover using mineral spirits. MECHANICAL REFINISHING OF POLISHED TERRAZZO & AGGLOMERATE MARBLE For scratch, etch and wear pattern removal and to restore the surface to an even finish. Depending on the severity of the damage to the stone and/or the desired surface appearance, choose one or more of the grit levels of the StoneTech Professional Honing Powder 180/280/400/600/800, StoneTech Professional Polishing Powder and/or StoneTech Professional Shining Powder as appropriate. For refinishing to a honed finish: 3 Strip off all topical finishes such as waxes and coatings. 4 Liberally apply Honing Powder to the stone surface. 5 Add water to form a milk-like consistency. 6 Refinish using a hand orbital sander or weighted floor machine at 130 lbs.-140 lbs., 175 rpm, fitted with a natural hair pad. 7 Keep compound wet with plenty of water while refinishing. Add Honing Powder as needed. 8 Refinish area until the desired level of hone has been achieved. 9 Rinse well and use a wet vacuum to remove all excess compound. 10 Clean equipment with water. For refinishing to a polish: Use successively higher grits of Honing Powder to close the face of the stone. Follow with Polishing Powder as applicable. 3 Strip off all topical finishes such as waxes and coatings. 4 Liberally apply Polishing Powder to the stone surface. 5 Add water to form a milk-like consistency. 6 Refinish using a hand orbital sander or weighted floor machine at 130 lbs.-140 lbs., 175 rpm, fitted with a natural hair pad. 7 Keep compound wet with plenty of water while refinishing. Add Polishing Powder as needed. 8 Refinish area until the desired level of polish has been achieved. 9 Rinse well and use a wet vacuum to remove all excess compound. 10 Clean equipment with water. For a highly polished finish: Use Shining Powder as applicable. See Maintenance Polishing. Care Instructions SEALING & PROTECTING Natural stone surfaces must be sealed to prevent or minimize staining. Leaving natural stone untreated may greatly hinder the complete removal of stains in the future. The following suggestions are for impregnating the stone and will allow the stone to breathe. Allow new installations to cure for 72 hours prior to applying sealer. For a natural looking protector on interior and exterior surfaces (heavy duty protection, water and oil repellency): Option 1: Heavy duty protection, water-based formula: 3 Insure that surface is clean and residue-free. 4 StoneTech Professional Heavy Duty Sealer may be applied to damp surfaces one hour after standing water has been removed. 5 Liberally apply an even coat of sealer using a paint pad, low-pressure chemical-resistant sprayer, roller or brush. 6 Allow sealer to penetrate the surface for minutes. During this time, distribute excess over entire area to insure even penetration. Wipe off any remaining sealer prior to drying on the surface. 7 A second coat may be needed for porous, absorbent surfaces and should be applied minutes after initial application as directed in steps A minimum of 15 minutes after final application, wipe entire surface with a clean dry towel to remove any residue and excess sealer, if needed. 9 If sealer was not completely wiped off and a residue appears, wipe entire surface with a towel dampened with sealer. Use a white, 10 A full cure is achieved after hours; foot 11 Expected coverage is 800-1,200 sq. ft. per StoneTech ProfessioNAL Stone & TILE CARE RESOURCE GUIDE /2007 Edition STONEHELP ( ) MARBLE GRANITE LIMESTONE TRAVERTINE SLATE 05

8 MARBLE GRANITE LIMESTONE TRAVERTINE SLATE 12 Re-application of Heavy Duty Sealer: A 1-3 year re-application is needed for exterior surfaces. Option 2: Heavy duty protection, solventbased formula: 3 Insure that surface is clean, dry and residuefree. 4 Ensure area is well-ventilated. Use a respirator if unsure that work area is well-ventilated. A NIOSH approved respirator with a combination HEPA/organic vapor cartridge is recommended. Follow respirator manufacturer s instructions for use. 5 Liberally apply an even coat of StoneTech Professional Impregnator Pro Sealer using a paint pad, roller, brush or pump-up garden sprayer. DO NOT USE A POWER SPRAYER. 6 Allow sealer to penetrate the surface for minutes; denser material may require more time for sealer to penetrate. During this time, distribute excess over entire area to insure even penetration. Wipe off any remaining sealer prior to drying on the surface. 7 A second coat may be needed for porous, absorbent surfaces and should be applied one hour after initial application as directed in steps If sealer was not completely wiped off and a residue appears, wipe entire surface with a towel dampened with sealer. Use a white, 9 A full cure is achieved after hours; foot 10 Expected coverage is 800-1,200 sq. ft. per 11 Re-application of Impregnator Pro Sealer: A 1-3 year re-application is needed for exterior surfaces. WARNING: HARMFUL VAPORS. HARMFUL OR FATAL IF SWALLOWED. COMBUSTIBLE. KEEP OUT OF THE REACH OF CHILDREN. Do not ingest. Avoid contact with eyes and skin. Avoid exposure to vapors. Use in a well-ventilated rea. For spray application: Use a pump-up garden sprayer. DO NOT USE A POWER SPRAYER. Use a respirator if unsure that work area is wellventilated. A NIOSH approved respirator with a combination HEPA/organic vapor cartridge is recommended. Follow respirator manufacturer s instructions for use. Do not freeze or store above 100 F/38 C. Do not mix with other chemicals For a natural looking protector on exterior surfaces (heavy duty protection, water repellency only): StoneTech Professional Heavy Duty Exterior Sealer is a water repellent specially designed for exterior projects such as facades, cladding, pool decks, parking areas and driveways. It is very resistant to chemicals (i.e., chlorine) and to the effects of weather (i.e., ultraviolet light/sunlight, driving water/rain). 3 Insure that the surface is clean, dry and residue-free. 4 Liberally apply an even coat of Heavy Duty Exterior Sealer with a paint pad, brush, paint roller or low-pressure solvent-resistant sprayer. 5 Allow sealer to penetrate the surface for 5-15 minutes; denser material may require more time for sealer to penetrate. During this time, distribute excess over entire area to insure even penetration. Wipe off any remaining sealer prior to drying on the surface. 6 A second coat may be needed for porous, absorbent surfaces and should be applied one hour after initial application as directed in steps If sealer was not completely wiped off and a residue appears, wipe entire surface with a towel dampened with sealer. Use a white, 8 Do not walk on surface for at least 4-6 hours. Full cure is achieved in hours. 9 Expected coverage is 800-1,200 sq. ft. per 10 Re-application of Heavy Duty Exterior Sealer: A 5-10 year re-application is recommended for exterior surfaces. MAINTENANCE CLEANING Highly alkaline, acidic, ammoniated, abrasive cleaners and/or bleach may break down the sealer, adversely affecting repellency and may not be good for the stone. Use a neutral cleaner specially formulated for natural stone. For routine cleaning with protection: Revitalizer Cleaner & Protector concentrate mixed with warm or hot water as suggested below: Light Duty Usage 1 part Revitalizer Cleaner & Protector to 4 parts water. Medium Duty Usage/Spray Refill 1 part Revitalizer Cleaner & Protector to 1 part water. (One gallon of concentrate makes up to five gallons of ready-to-use solution.) 3 Apply the Revitalizer Cleaner & Protector solution using a low-pressure chemicalresistant sprayer, mop, sponge or automatic scrubbing machine. 4 No rinsing needed. 5 Or use Revitalizer Cleaner & Protector in a ready-to-use spray bottle or wipes. For routine maintenance cleaning: Stone & Tile Cleaner concentrate mixed with warm or hot water as suggested below: 2 ounces Stone & Tile Cleaner in 1 gallon of water. (Do not mix stronger than 2 ounces to a gallon as a maintenance cleaner. One gallon of concentrate makes 65 gallons of cleaning solution.) 3 Apply the solution using a sponge, mop or automatic scrubbing machine, then wipe or rinse off. 4 Or use Stone & Tile Cleaner in a ready-to-use spray bottle or wipes. MAINTENANCE POLISHING To maintain the shine and beauty of polished terrazzo & agglomerate marble on a routine basis and to minimize the need for restorative polishing: 3 Liberally apply Shining Powder to the surface. 4 Add enough water to form a milk-like consistency. 5 Refinish using a hand orbital sander or weighted floor machine at 130 lbs.-140 lbs., 175 rpm, fitted with a natural hair pad. 6 Rinse well and use a wet vacuum to remove all remaining compound. 7 Expected coverage is 1,000-1,700 sq. ft. per 1.5 lb. canister. 8 Re-application: Semi-annually or as needed. For a brilliant shine on countertops, vanities and vertical surfaces: 1 On a cleaned surface, spray a light coat of StoneTech Professional Polish over the entire surface. Do not spray in eyes. 2 Spread the polish evenly with a clean, white terry cloth towel. 3 Buff off polish. Keep turning the towel to insure that a clean section is being used for maximum efficiency. 4 Continue buffing until there is no visible polish left and high shine appears. 5 Reapplication as desired. Note: Polish will work best on stone previously sealed with StoneTech Professional sealers. 06

9 Less Absorptive Polished Granite Homogenous Granite READ ALL INSTRUCTIONS AND PRODUCT LABELS COMPLETELY BEFORE USING Pretest in an inconspicuous area prior to application to determine if the desired results will be achieved and that the stone is not adversely affected. NEW INSTALLATIONS Follow the recommended installation methods and procedures of the Marble Institute of America and the Tile Contractors Association. RESTORATIVE CLEANING Depending on the type of soil, stain or other foreign matter present, select one or more of the following options: For stripping off any existing topical acrylic, urethane, epoxy, heavy wax coatings and epoxy grout haze: 3 For heavy, hard to remove coatings, use a commercially available coating stripper. Follow instructions as indicated on bottle. For cleaning of grease, oil, dirt, dry soil and soap scum: 3 Strip off all topical finishes such as waxes and coatings. 4 Prepare a solution of StoneTech Professional KlenzAll mixed with warm or hot water as suggested below: Medium Duty Usage Mix 1 part KlenzAll to 4 parts of water. Heavy Duty Usage Mix 1 part KlenzAll to 2 parts of water. 5 Apply KlenzAll using a low-pressure chemical-resistant sprayer, sponge or mop. 6 Agitate well using a stiff nylon bristle scrub brush, stiff bristle push broom or a weighted floor machine at 130 lbs.-140 lbs., 175 rpm, fitted with a scrub brush attachment. 7 Rinse well with clean water and mop, sponge or wet vacuum to remove the remaining cleaning solution. A hard surface extraction wand and portable or truck mounted extraction machine may be used. Repeat the rinsing and wet vacuum process to insure that all dirt, soil and cleaner residue have been removed. 8 To remove deep or stubborn oil stains not completely removed by KlenzAll, let the surface dry and use StoneTech Professional Oil Stain Remover. a Apply a ¼ inch thick coat of Oil Stain Remover to the oil stained area. Insure that Oil Stain Remover covers an area 1 to 2 beyond the stained area for the purpose of containment. b Allow 2-3 days for the Oil Stain Remover to dry to a powder. c Sweep and wipe up dried powder and evaluate the stained area for removal. d Repeat process if needed. e Remove any remaining Oil Stain Remover using mineral spirits. For removal of efflorescence, grout haze, salts, mineral deposits and all other calcium-based stains (acidic cleaning): Restore may damage stainless steel and other metals. 3 Strip off all wax, acrylic, urethane and all topical finishes. 4 Prepare a solution of Restore mixed with warm or hot water as suggested below: Medium Duty Usage Mix 1 part of Restore to 4 parts of water. Heavy Duty Usage Mix 1 part of Restore to 1 part of water. 5 Liberally apply using a low-pressure chemicalresistant sprayer, sponge or mop. 6 Agitate well using a stiff nylon bristle scrub brush, stiff bristle push broom or a weighted floor machine at 130 lbs.-140 lbs., 175 rpm, fitted with a scrub brush attachment. 7 Rinse well with clean water and mop, sponge or wet vacuum to remove the remaining solution. A hard surface extraction wand and portable or truck mounted extraction machine may be used. Repeat the rinsing and wet vacuum process to insure that all dirt, soil and cleaner residue have been removed. Thoroughly rinse all metal surfaces. SEALING & PROTECTING Natural stone surfaces must be sealed to prevent or minimize staining. Leaving natural stone untreated may greatly hinder the complete removal of stains in the future. The following suggestions are for impregnating the stone and will allow the stone to breathe. Allow new installations to cure for 72 hours prior to applying sealer. For a natural looking protector on interior and exterior surfaces (heavy duty protection, water and oil repellency): Option 1: Heavy duty protection, water-based formula: 3 Insure that surface is clean and residue-free. 4 StoneTech Professional Heavy Duty Sealer may be applied to damp surfaces one hour after standing water has been removed. 5 Liberally apply an even coat of sealer using a paint pad, low-pressure chemical-resistant sprayer, roller or brush. 6 Allow sealer to penetrate the surface for minutes. During this time, distribute excess over entire area to insure even penetration. Wipe off any remaining sealer prior to drying on the surface. 7 A second coat may be needed for porous, absorbent surfaces and should be applied minutes after initial application as directed in steps 5-6. Care Instructions 8 A minimum of 15 minutes after final application, wipe entire surface with a clean dry towel to remove any residue and excess sealer, if needed. 9 If sealer was not completely wiped off and a residue appears, wipe entire surface with a towel dampened with sealer. Use a white, 10 A full cure is achieved after hours; foot 11 Expected coverage is 800-1,500 sq. ft. per 12 Re-application of Heavy Duty Sealer: A 1-3 year re-application is needed for exterior surfaces. Option 2: Heavy duty protection, solventbased formula: 3 Insure that surface is clean, dry and residuefree. 4 Ensure area is well-ventilated. Use a respirator if unsure that work area is well-ventilated. A NIOSH approved respirator with a combination HEPA/organic vapor cartridge is recommended. Follow respirator manufacturer s instructions for use. 5 Liberally apply an even coat of StoneTech Professional Impregnator Pro Sealer using a paint pad, roller, brush or pump-up garden sprayer. DO NOT USE A POWER SPRAYER. 6 Allow sealer to penetrate the surface for minutes; denser material may require more time for sealer to penetrate. During this time, distribute excess over entire area to insure even penetration. Wipe off any remaining sealer prior to drying on the surface. 7 A second coat may be needed for porous, absorbent surfaces and should be applied one hour after initial application as directed in steps If sealer was not completely wiped off and a residue appears, wipe entire surface with a towel dampened with sealer. Use a white, 9 If sealer was not completely wiped off and a residue appears, wipe entire surface with a towel dampened with sealer. Use a white, 10 A full cure is achieved after hours; foot 11 Expected coverage is 800-1,500 sq. ft. per 12 Re-application of Impregnator Pro Sealer: StoneTech ProfessioNAL Stone & TILE CARE RESOURCE GUIDE /2007 Edition STONEHELP ( ) MARBLE GRANITE LIMESTONE TRAVERTINE SLATE 07

10 MARBLE GRANITE LIMESTONE TRAVERTINE SLATE A 1-3 year re-application is needed for exterior surfaces. WARNING: HARMFUL VAPORS. HARMFUL OR FATAL IF SWALLOWED. COMBUSTIBLE. KEEP OUT OF THE REACH OF CHILDREN. Do not ingest. Avoid contact with eyes and skin. Avoid exposure to vapors. Use in a well-ventilated rea. For spray application: Use a pump-up garden sprayer. DO NOT USE A POWER SPRAYER. Use a respirator if unsure that work area is wellventilated. A NIOSH approved respirator with a combination HEPA/organic vapor cartridge is recommended. Follow respirator manufacturer s instructions for use. Do not freeze or store above 100 F/38 C. Do not mix with other chemicals. For a natural looking protector on exterior surfaces (heavy duty protection, water repellency only): StoneTech Professional Heavy Duty Exterior Sealer is a water repellent specially designed for exterior projects such as facades, cladding, pool decks, parking areas and driveways. It is very resistant to chemicals (i.e., chlorine) and to the effects of weather (i.e., ultraviolet light/sunlight, driving water/rain). 3 Insure that the surface is clean, dry and residue-free. 4 Liberally apply an even coat of Heavy Duty Exterior Sealer with a paint pad, brush, paint roller or low-pressure solvent-resistant sprayer. 5 Allow sealer to penetrate, about 5-15 minutes. 6 Wipe off any remaining sealer prior to drying on surface. 7 Do not walk on surface for at least 4-6 hours. Full cure is achieved in hours. 8 Expected coverage is 800-1,500 sq. ft. per 9 Re-application of Heavy Duty Exterior Sealer: A 5-10 year re-application is needed for exterior surfaces. For a color enhancing, impregnating (non-topical) protector on interior and exterior surfaces (heavy duty protection, water and oil repellency): 3 Insure that surface is clean, dry and residuefree. Surface temperature should be between 50 F and 80 F. 4 Ensure area is well-ventilated. Use a respirator if unsure that work area is well-ventilated. A NIOSH approved respirator with a combination HEPA/organic vapor cartridge is recommended. Follow respirator manufacturer s instructions for use. 5 Liberally apply an even coat of StoneTech Professional Enhancer Pro Sealer using a paint pad, roller, brush or pump-up garden sprayer. DO NOT USE A POWER SPRAYER. Ensure that Enhancer Pro is distributed evenly over the entire surface to ensure even penetration. Uneven penetration will result in a blotchy appearance. 6 Allow to penetrate the surface for minutes; denser material may require maximum time for Enhancer Pro to penetrate. During this time, distribute excess over entire area to insure even penetration. Completely wipe surface dry with a clean dry terrycloth towel. DO NOT ALLOW ENHANCER PRO TO DRY COMPLETELY ON SURFACE! Failure to remove enhancer from the surface may result in a film or residue that may need to be mechanically removed. 7 A second coat is recommended for porous, absorbent surfaces or if a darker appearance is required and should be applied one hour after initial application as directed in steps If sealer was not completely wiped off and a residue appears, wipe entire surface with a towel dampened with sealer. Use a white, 9 A full cure is achieved after hours; foot 10 Expected coverage is 800-1,200 sq. ft. per 11 Re-application of Enhancer Pro : interior or exterior surfaces. WARNING: HARMFUL VAPORS. HARMFUL OR FATAL IF SWALLOWED. COMBUSTIBLE. KEEP OUT OF THE REACH OF CHILDREN. Do not ingest. Avoid contact with eyes and skin. Avoid exposure to vapors. Use in a well-ventilated rea. For spray application: Use a pump-up garden sprayer. DO NOT USE A POWER SPRAYER. Use a respirator if unsure that work area is wellventilated. A NIOSH approved respirator with a combination HEPA/organic vapor cartridge is recommended. Follow respirator manufacturer s instructions for use. Do not freeze or store above 100 F/38 C. Do not mix with other chemicals. For color enhancement of edges on resin-treated granite: 1 Polish edge as customary with mechanical processes. 2 Insure that surface is clean, dry and residuefree. Surface temperature should be between 50 F and 80 F. 3 Ensure area is well-ventilated. Use a respirator if unsure that work area is well-ventilated. A NIOSH approved respirator with a combination HEPA/organic vapor cartridge is recommended. Follow respirator manufacturer s instructions for use. 4 Liberally apply an even coat of StoneTech Professional Enhancer Pro Sealer using a paint pad, roller, brush or pump-up garden sprayer. DO NOT USE A POWER SPRAYER. Ensure that Enhancer Pro is distributed evenly over the entire surface to ensure even penetration. Uneven penetration will result in a blotchy appearance. 5 Allow to penetrate the surface for minutes; denser material may require maximum time for Enhancer Pro to penetrate. During this time, distribute excess over entire area to insure even penetration. Completely wipe surface dry. WITH A CLEAN DRY TERRYCLOTH TOWEL. DO NOT ALLOW ENHANCER PRO TO DRY COMPLETELY ON SURFACE! Failure to remove enhancer from the surface may result in a film or residue that may need to be mechanically removed. 6 If sealer was not completely wiped off and a residue appears, wipe entire surface with a towel dampened with sealer. Use a white, 7 A second coat is recommended for porous, absorbent surfaces or if a darker appearance is required and should be applied one hour after initial application as directed in steps 4-5. WARNING: HARMFUL VAPORS. HARMFUL OR FATAL IF SWALLOWED. COMBUSTIBLE. KEEP OUT OF THE REACH OF CHILDREN. Do not ingest. Avoid contact with eyes and skin. Avoid exposure to vapors. Use in a well-ventilated rea. For spray application: Use a pump-up garden sprayer. DO NOT USE A POWER SPRAYER. Use a respirator if unsure that work area is wellventilated. A NIOSH approved respirator with a combination HEPA/organic vapor cartridge is recommended. Follow respirator manufacturer s instructions for use. Do not freeze or store above 100 F/38 C. Do not mix with other chemicals. MAINTENANCE CLEANING Highly alkaline, acidic, ammoniated, abrasive cleaners and/or bleach may break down the sealer, adversely affecting repellency and may not be good for the stone. Use a neutral cleaner specially formulated for natural stone. For routine cleaning with protection: Revitalizer Cleaner & Protector concentrate mixed with warm or hot water as suggested below: Light Duty Usage 1 part Revitalizer Cleaner & Protector to 4 parts water. Medium Duty Usage/Spray Refill 1 part Revitalizer Cleaner & Protector to 1 part water. (One gallon of concentrate makes up to five gallons of ready-to-use solution.) 3 Apply the Revitalizer Cleaner & Protector solution using a low-pressure chemicalresistant sprayer, mop, sponge or automatic scrubbing machine. 4 No rinsing needed. 5 Or use Revitalizer Cleaner & Protector in a ready-to-use spray bottle or wipes. For routine maintenance cleaning: Stone & Tile Cleaner concentrate mixed with warm or hot water as suggested below: 2 ounces Stone & Tile Cleaner in 1 gallon of water. (Do not mix stronger than 2 ounces to a gallon as a maintenance cleaner. One gallon of concentrate makes 65 gallons of cleaning solution.) 3 Apply the solution using a sponge, mop or automatic scrubbing machine, then wipe or rinse off. 4 Or use Stone & Tile Cleaner in a ready-to-use spray bottle or wipes. MAINTENANCE POLISHING For a brilliant shine on countertops, vanities and vertical surfaces: 1 On a cleaned surface, spray a light coat of StoneTech Professional Polish over the entire surface. Do not spray in eyes. 2 Spread the polish evenly with a clean, white terry cloth towel. 3 Buff off polish. Keep turning the towel to insure that a clean section is being used for maximum efficiency. 4 Continue buffing until there is no visible polish left and high shine appears. 5 Reapplication as desired. Note: Polish will work best on stone previously sealed with StoneTech Professional sealers. 08

11 More Absorptive Polished Granite Oriented & Veined Granite READ ALL INSTRUCTIONS AND PRODUCT LABELS COMPLETELY BEFORE USING Pretest in an inconspicuous area prior to application to determine if the desired results will be achieved and that the stone is not adversely affected. NEW INSTALLATIONS Follow the recommended installation methods and procedures of the Marble Institute of America and the Tile Contractors Association. PRE-GROUTING For making grout clean up easier on porous stone: 2 Insure that surface temperature of the stone is between 50-80ºF. 3 Apply a single coat of StoneTech Professional Grout Release using a paint pad, low-pressure chemical-resistant sprayer, roller or brush. 4 Allow the Grout Release to completely penetrate the stone for 5-15 minutes. 5 Wipe up all remaining sealer from the surface of the stone. Do not allow pooling or sealer to dry on the surface. Do not over apply. 6 Allow for a minimum of 4 hours cure time prior to grouting. 7 After grouting, remove excess grout. Do not allow grout to completely dry prior to removal. 8 Expected coverage for Grout Release is sq. ft. per RESTORATIVE CLEANING Depending on the type of soil, stain or other foreign matter present, select one or more of the following options: For stripping off any existing topical acrylic, urethane, epoxy, heavy wax coatings and epoxy grout haze: 3 For heavy, hard to remove coatings, use a commercially available coating stripper. Follow instructions as indicated on bottle. For cleaning of grease, oil, dirt, dry soil and soap scum: 3 Strip off all topical finishes such as waxes and coatings. 4 Prepare a solution of StoneTech Professional KlenzAll mixed with warm or hot water as suggested below: Medium Duty Usage Mix 1 part KlenzAll to 4 parts of water. Heavy Duty Usage Mix 1 part KlenzAll to 2 parts of water. 5 Apply KlenzAll using a low-pressure chemical-resistant sprayer, sponge or mop. 6 Agitate well using a stiff nylon bristle scrub brush, stiff bristle push broom or a weighted floor machine at 130 lbs.-140 lbs., 175 rpm, fitted with a scrub brush attachment. 7 Rinse well with clean water and mop, sponge or wet vacuum to remove the remaining cleaning solution. A hard surface extraction wand and portable or truck mounted extraction machine may be used. Repeat the rinsing and wet vacuum process to insure that all dirt, soil and cleaner residue have been removed. 8 To remove deep or stubborn oil stains not completely removed by KlenzAll, let the surface dry and use StoneTech Professional Oil Stain Remover. a Apply a ¼ inch thick coat of Oil Stain Remover to the oil stained area. Insure that Oil Stain Remover covers an area 1 to 2 beyond the stained area for the purpose of containment. b Allow 2-3 days for the Oil Stain Remover to dry to a powder. c Sweep and wipe up dried powder and evaluate the stained area for removal. d Repeat process if needed. e Remove any remaining Oil Stain Remover using mineral spirits. For removal of efflorescence, grout haze, salts, mineral deposits and all other calcium-based stains (acidic cleaning): Restore may damage stainless steel and other surfaces. 3 Strip off all wax, acrylic, urethane and all topical finishes. 4 Prepare a solution of Restore mixed with warm or hot water as suggested below: Medium Duty Usage Mix 1 part of Restore to 4 parts of water. Heavy Duty Usage Mix 1 part of Restore to 1 part of water. 5 Liberally apply using a low-pressure chemicalresistant sprayer, sponge or mop. 6 Agitate well using a stiff nylon bristle scrub brush, stiff bristle push broom or a weighted floor machine at 130 lbs.-140 lbs., 175 rpm, fitted with a scrub brush attachment. 7 Rinse well with clean water and mop, sponge or wet vacuum to remove the remaining solution. A hard surface extraction wand and portable or truck mounted extraction machine may be used. Repeat the rinsing and wet vacuum process to insure that all dirt, soil and cleaner residue have been removed. Thoroughly rinse all metal surfaces. SEALING & PROTECTING Natural stone surfaces must be sealed to prevent or minimize staining. Leaving natural stone untreated may greatly hinder the complete removal of stains in the future. The following Care Instructions suggestions are for impregnating the stone and will allow the stone to breathe. Allow new installations to cure for 72 hours prior to applying sealer. For a natural looking protector on interior and exterior surfaces (maximum protection, water and oil repellency): 3 Insure that surface is clean and residue-free. 4 StoneTech Professional BulletProof Sealer may be applied to damp surfaces one hour after standing water has been removed. 5 Liberally apply an even coat of sealer using a paint pad, low-pressure chemical-resistant sprayer, roller or brush. 6 Allow sealer to penetrate the surface for minutes. During this time, distribute excess over entire area to insure even penetration. Wipe off any remaining sealer prior to drying on the surface. 7 A second coat may be needed for porous, absorbent surfaces and should be applied minutes after initial application as directed in steps A minimum of 15 minutes after final application, wipe entire surface with a towel dampened with sealer to remove any residue and excess sealer, if needed. 9 If sealer was not completely wiped off and a residue appears, wipe entire surface with 10 A full cure is achieved after hours; foot 11 Expected coverage is sq. ft. per 12 Re-application of BulletProof Sealer: A 1-3 year re-application is needed for exterior surfaces. For a natural looking protector on exterior surfaces (heavy duty protection, water repellency only): StoneTech Professional Heavy Duty Exterior Sealer is a water repellent specially designed for exterior projects such as facades, cladding, pool decks, parking areas and driveways. It is very resistant to chemicals (i.e., chlorine) and to the effects of weather (i.e., ultraviolet light/sunlight, driving water/rain). 3 Insure that the surface is clean, dry and residue-free. StoneTech ProfessioNAL Stone & TILE CARE RESOURCE GUIDE /2007 Edition STONEHELP ( ) MARBLE GRANITE LIMESTONE TRAVERTINE SLATE 09

12 MARBLE GRANITE LIMESTONE TRAVERTINE SLATE 4 Liberally apply an even coat of Heavy Duty Exterior Sealer with a paint pad, brush, paint roller or low-pressure solvent-resistant sprayer. 5 Allow sealer to penetrate the surface for 5-15 minutes; denser material may require more time for sealer to penetrate. During this time, distribute excess over entire area to insure even penetration. Wipe off any remaining sealer prior to drying on the surface. 6 A second coat may be needed for porous, absorbent surfaces and should be applied one hour after initial application as directed in steps If sealer was not completely wiped off and a residue appears, wipe entire surface with a towel dampened with sealer. Use a white, non-abrasive nylon brush or pad to loosen residue and follow with a clean, white 8 Do not walk on surface for at least 4-6 hours. Full cure is achieved in hours. 9 Expected coverage is sq. ft. per 10 Re-application of Heavy Duty Exterior Sealer: A 5-10 year re-application is recommended for exterior surfaces. For a color enhancing, impregnating (non-topical) protector on interior and exterior surfaces (heavy duty protection, water and oil repellency): 3 Insure that surface is clean, dry and residuefree. Surface temperature should be between 50 F and 80 F. 4 Ensure area is well-ventilated. Use a respirator if unsure that work area is well-ventilated. A NIOSH approved respirator with a combination HEPA/organic vapor cartridge is recommended. Follow respirator manufacturer s instructions for use. 5 Liberally apply an even coat of StoneTech Professional Enhancer Pro Sealer using a paint pad, roller, brush or pump-up garden sprayer. DO NOT USE A POWER SPRAYER. Ensure that Enhancer Pro is distributed evenly over the entire surface to ensure even penetration. Uneven penetration will result in a blotchy appearance. 6 Allow to penetrate the surface for minutes; denser material may require more time for Enhancer Pro to penetrate. During this time, distribute excess over entire area to insure even penetration. Completely wipe surface dry. DO NOT ALLOW ENHANCER PRO TO DRY COMPLETELY ON SURFACE! Failure to remove enhancer from the surface may result in a film or residue that may need to be mechanically removed. 7 A second coat may be needed for porous, absorbent surfaces or if a darker appearance is required and should be applied one hour after initial application as directed in steps If sealer was not completely wiped off and a residue appears, wipe entire surface with a towel dampened with sealer. Use a white, 9 A full cure is achieved after hours; foot 10 Expected coverage is sq. ft. per 11 Re-application of Enhancer Pro : interior or exterior surfaces. WARNING: HARMFUL VAPORS. HARMFUL OR FATAL IF SWALLOWED. COMBUSTIBLE. KEEP OUT OF THE REACH OF CHILDREN. Do not ingest. Avoid contact with eyes and skin. Avoid exposure to vapors. Use in a well-ventilated area. For spray application: Use a pump-up garden sprayer. DO NOT USE A POWER SPRAYER. Use a respirator if unsure that work area is wellventilated. A NIOSH approved respirator with a combination HEPA/organic vapor cartridge is recommended. Follow respirator manufacturer s instructions for use. Do not freeze or store above 100 F/38 C. Do not mix with other chemicals. For color enhancement of edges on resin-treated granite: 1 Polish edge as customary with mechanical processes. 2 Insure that surface is clean, dry and residuefree. Surface temperature should be between 50 F and 80 F. 3 Ensure area is well-ventilated. Use a respirator if unsure that work area is well-ventilated. A NIOSH approved respirator with a combination HEPA/organic vapor cartridge is recommended. Follow respirator manufacturer s instructions for use. 4 Liberally apply an even coat of StoneTech Professional Enhancer Pro Sealer using a paint pad, roller, brush or pump-up garden sprayer. DO NOT USE A POWER SPRAYER. Ensure that Enhancer Pro is distributed evenly over the entire surface to ensure even penetration. Uneven penetration will result in a blotchy appearance. 5 Allow to penetrate the surface for minutes; denser material may require maximum time for Enhancer Pro to penetrate. During this time, distribute excess over entire area to insure even penetration. Completely wipe surface with a clean dry terrycloth towel. DO NOT ALLOW ENHANCER PRO TO DRY COMPLETELY ON SURFACE! Failure to remove enhancer from the surface may result in a film or residue that may need to be mechanically removed. 6 If sealer was not completely wiped off and a residue appears, wipe entire surface with a towel dampened with sealer. Use a white, 7 A second coat is recommended for porous, absorbent surfaces or if a darker appearance is required and should be applied one hour after initial application as directed in steps 4-5. WARNING: HARMFUL VAPORS. HARMFUL OR FATAL IF SWALLOWED. COMBUSTIBLE. KEEP OUT OF THE REACH OF CHILDREN. Do not ingest. Avoid contact with eyes and skin. Avoid exposure to vapors. Use in a well-ventilated area. For spray application: Use a pump-up garden sprayer. DO NOT USE A POWER SPRAYER. Use a respirator if unsure that work area is wellventilated. A NIOSH approved respirator with a combination HEPA/organic vapor cartridge is recommended. Follow respirator manufacturer s instructions for use. Do not freeze or store above 100 F/38 C. Do not mix with other chemicals. MAINTENANCE CLEANING Highly alkaline, acidic, ammoniated, abrasive cleaners and/or bleach may break down the sealer, adversely affecting repellency and may not be good for the stone. Use a neutral cleaner specially formulated for natural stone. For routine cleaning with protection: Revitalizer Cleaner & Protector concentrate mixed with warm or hot water as suggested below: Light Duty Usage 1 part Revitalizer Cleaner & Protector to 4 parts water. Medium Duty Usage/Spray Refill 1 part Revitalizer Cleaner & Protector to 1 part water. (One gallon of concentrate makes up to five gallons of ready-to-use solution.) 3 Apply the Revitalizer Cleaner & Protector solution using a low-pressure chemicalresistant sprayer, mop, sponge or automatic scrubbing machine. 4 No rinsing needed. 5 Or use Revitalizer Cleaner & Protector in a ready-to-use spray bottle or wipes. For routine maintenance cleaning: All Purpose Stone and Tile Cleaner concentrate mixed with warm or hot water as suggested below: 2 ounces Stone & Tile Cleaner in 1 gallon of water. (Do not mix stronger than 2 ounces to a gallon as a maintenance cleaner. One gallon of concentrate makes 65 gallons of cleaning solution.) 3 Apply the solution using a sponge, mop or automatic scrubbing machine, then wipe or rinse off. 4 Or use Stone & Tile Cleaner in a ready-to-use spray bottle or wipes. MAINTENANCE POLISHING For a brilliant shine on countertops, vanities and vertical surfaces: 1 On a cleaned surface, spray a light coat of StoneTech Professional Polish over the entire surface. Do not spray in eyes. 2 Spread the polish evenly with a clean, white terry cloth towel. 3 Buff off polish. Keep turning the towel to insure that a clean section is being used for maximum efficiency. 4 Continue buffing until there is no visible polish left and high shine appears. 5 Reapplication as desired. Note: Polish will work best on stone previously sealed with StoneTech Professional sealers. 10

13 Unpolished, Honed & Textured Granite Homogenous, Veined & Oriented Granite READ ALL INSTRUCTIONS AND PRODUCT LABELS COMPLETELY BEFORE USING Pretest in an inconspicuous area prior to application to determine if the desired results will be achieved and that the stone is not adversely affected. NEW INSTALLATIONS Allow the recommended installation methods and procedures of the Marble Institute of America and the Tile Contractors Association. PRE-GROUTING For making grout clean up easier on porous stone: 2 Insure that surface temperature of the stone is between 50-80ºF. 3 Apply a single coat of StoneTech Professional Grout Release using a paint pad, low-pressure chemical-resistant sprayer, roller or brush. 4 Allow the Grout Release to completely penetrate the stone for 5-15 minutes. 5 Wipe up all remaining sealer from the surface of the stone. Do not allow pooling or sealer to dry on the surface. Do not over apply. 6 Allow for a minimum of 4 hours cure time prior to grouting. 7 After grouting, remove excess grout. Do not allow grout to completely dry prior to removal. 8 Expected coverage for Grout Release is sq. ft. per RESTORATIVE CLEANING Depending on the type of soil, stain or other foreign matter present, select one or more of the following options: For stripping off any existing topical acrylic, urethane, epoxy, heavy wax coatings and epoxy grout haze: 3 For heavy, hard to remove coatings, use a commercially available coating stripper. Follow instructions as indicated on bottle. For cleaning of grease, oil, dirt, dry soil and soap scum: 3 Strip off all topical finishes such as waxes and coatings. 4 Prepare a solution of StoneTech Professional KlenzAll mixed with warm or hot water as suggested below: Medium Duty Usage Mix 1 part KlenzAll to 4 parts of water. Heavy Duty Usage Mix 1 part KlenzAll to 2 parts of water. 5 Apply KlenzAll using a low-pressure chemical-resistant sprayer, sponge or mop. 6 Agitate well using a stiff nylon bristle scrub brush, stiff bristle push broom or a weighted floor machine at 130 lbs.-140 lbs., 175 rpm, fitted with a scrub brush attachment. 7 Rinse well with clean water and mop, sponge or wet vacuum to remove the remaining cleaning solution. A hard surface extraction wand and portable or truck mounted extraction machine may be used. Repeat the rinsing and wet vacuum process to insure that all dirt, soil and cleaner residue have been removed. 8 To remove deep or stubborn oil stains not completely removed by KlenzAll, let the surface dry and use StoneTech Professional Oil Stain Remover. a Apply a ¼ inch thick coat of Oil Stain Remover to the oil stained area. Insure that Oil Stain Remover covers an area 1 to 2 beyond the stained area for the purpose of containment. b Allow 2-3 days for the Oil Stain Remover to dry to a powder. c Sweep and wipe up dried powder and evaluate the stained area for removal. d Repeat process if needed. e Remove any remaining Oil Stain Remover using mineral spirits. For removal of efflorescence, grout haze, salts, mineral deposits and all other calcium-based stains (acidic cleaning): Restore may damage stainless steel and other surfaces. 3 Strip off all wax, acrylic, urethane and all topical finishes. 4 Prepare a solution of Restore mixed with warm or hot water as suggested below: Medium Duty Usage Mix 1 part of Restore to 4 parts of water. Heavy Duty Usage Mix 1 part of Restore to 1 part of water. 5 Liberally apply using a low-pressure chemicalresistant sprayer, sponge or mop. 6 Agitate well using a stiff nylon bristle scrub brush, stiff bristle push broom or a weighted floor machine at 130 lbs.-140 lbs., 175 rpm, fitted with a scrub brush attachment. 7 Rinse well with clean water and mop, sponge or wet vacuum to remove the remaining solution. A hard surface extraction wand and portable or truck mounted extraction machine may be used. Repeat the rinsing and wet vacuum process to insure that all dirt, soil and cleaner residue have been removed. Thoroughly rinse all metal surfaces. SEALING & PROTECTING Care Instructions Natural stone surfaces must be sealed to prevent or minimize staining. Leaving natural stone untreated may greatly hinder the complete removal of stains in the future. The following suggestions are for impregnating the stone and will allow the stone to breathe. Allow new installations to cure for 72 hours prior to applying sealer. For a natural looking protector on interior and exterior surfaces (heavy duty or maximum protection, water and oil repellency): Option 1: Maximum protection, water-based formula: 3 Insure that surface is clean and residue-free. 4 StoneTech Professional BulletProof Sealer may be applied to damp surfaces one hour after standing water has been removed. 5 Liberally apply an even coat of sealer using a paint pad, low-pressure chemical-resistant sprayer, roller or brush. 6 Allow sealer to penetrate the surface for minutes. During this time, distribute excess over entire area to insure even penetration. Wipe off any remaining sealer prior to drying on the surface. 7 A second coat may be needed for porous, absorbent surfaces and should be applied minutes after initial application as directed in steps A minimum of 15 minutes after final application, wipe entire surface with a towel dampened with sealer to remove any residue and excess sealer, if needed. 9 If sealer was not completely wiped off and a residue appears, wipe entire surface with a towel dampened with sealer. Use a white, 10 A full cure is achieved after hours; foot 11 Expected coverage is sq. ft. per 12 Re-application of BulletProof Sealer: A 1-3 year re-application is needed for exterior surfaces. Option 2: Heavy duty protection for less absorptive unpolished, honed and textured granite, water-based formula: MARBLE GRANITE LIMESTONE TRAVERTINE SLATE StoneTech ProfessioNAL Stone & TILE CARE RESOURCE GUIDE /2007 Edition STONEHELP ( ) 11

14 MARBLE GRANITE LIMESTONE TRAVERTINE SLATE 3 Insure that surface is clean and residue-free. 4 StoneTech Professional Heavy Duty Sealer may be applied to damp surfaces one hour after standing water has been removed. 5 Liberally apply an even coat of sealer using a paint pad, low-pressure chemical-resistant sprayer, roller or brush. 6 Allow sealer to penetrate the surface for minutes. During this time, distribute excess over entire area to insure even penetration. Wipe off any remaining sealer prior to drying on the surface. 7 A second coat is recommended for porous, absorbent surfaces and should be applied minutes after initial application as directed in steps A minimum of 15 minutes after final application, wipe entire surface with a clean dry towel to remove any residue and excess sealer, if needed. 9 If sealer was not completely wiped off and a residue appears, wipe entire surface with 10 A full cure is achieved after hours; foot 11 Expected coverage is sq. ft. per 12 Re-application of Heavy Duty Sealer: A 1-3 year re-application is needed for exterior surfaces. For a natural looking protector on exterior surfaces (heavy duty protection, water repellency only): StoneTech Professional Heavy Duty Exterior Sealer is a water repellent specially designed for exterior projects such as facades, cladding, pool decks, parking areas and driveways. It is very resistant to chemicals (i.e., chlorine) and to the effects of weather (i.e., ultraviolet light/sunlight, driving water/rain). 3 Insure that the surface is clean, dry and residue-free. 4 Liberally apply an even coat of Heavy Duty Exterior Sealer with a paint pad, brush, paint roller or low-pressure solvent-resistant sprayer. 5 Allow sealer to penetrate the surface for 5-15 minutes; denser material may require more time for sealer to penetrate. During this time, distribute excess over entire area to insure even penetration. Wipe off any remaining sealer prior to drying on the surface. 6 A second coat may be needed for porous, absorbent surfaces and should be applied one hour after initial application as directed in steps If sealer was not completely wiped off and a residue appears, wipe entire surface with a towel dampened with sealer. Use a white, 8 Do not walk on surface for at least 4-6 hours. Full cure is achieved in hours. 9 Expected coverage is sq. ft. per 10 Re-application of Heavy Duty Exterior Sealer: A 5-10 year re-application is recommended for exterior surfaces. For a color enhancing, impregnating (non-topical) protector on interior and exterior surfaces (heavy duty protection, water and oil repellency): 3 Insure that surface is clean, dry and residuefree. Surface temperature should be between 50 F and 80 F. 4 Ensure area is well-ventilated. Use a respirator if unsure that work area is well-ventilated. A NIOSH approved respirator with combination HEPA/organic vapor cartridge is recommended. Follow respirator manufacturer s instructions for use. 5 Liberally apply an even coat of StoneTech Professional Enhancer Pro Sealer using a paint pad, roller, brush or pump-up garden sprayer. DO NOT USE A POWER SPRAYER. Ensure that Enhancer Pro is distributed evenly over the entire surface to ensure even penetration. Uneven penetration will result in a blotchy appearance. 6 Allow to penetrate the surface for minutes; denser material may require more time for Enhancer Pro to penetrate. During this time, distribute excess over entire area to insure even penetration. Completely wipe surface with a clean dry terrycloth towel. DO NOT ALLOW ENHANCER PRO TO DRY COMPLETELY ON SURFACE! Failure to remove enhancer from the surface may result in a film or residue that may need to be mechanically removed. 7 A second coat may be needed for porous, absorbent surfaces or if a darker appearance is required and should be applied one hour after initial application as directed in steps If sealer was not completely wiped off and a residue appears, wipe entire surface with 9 A full cure is achieved after hours; foot 10 Expected coverage is sq. ft. per 11 Re-application of Enhancer Pro : interior or exterior surfaces. WARNING: HARMFUL VAPORS. HARMFUL OR FATAL IF SWALLOWED. COMBUSTIBLE. KEEP OUT OF THE REACH OF CHILDREN. Do not ingest. Avoid contact with eyes and skin. Avoid exposure to vapors. Use in a well-ventilated area. For spray application: Use a pump-up garden sprayer. DO NOT USE A POWER SPRAYER. Use a respirator if unsure that work area is wellventilated. A NIOSH approved respirator with a combination HEPA/organic vapor cartridge is recommended. Follow respirator manufacturer s instructions for use. Do not freeze or store above 100 F/38 C. Do not mix with other chemicals. MAINTENANCE CLEANING Highly alkaline, acidic, ammoniated, abrasive cleaners and/or bleach may break down the sealer, adversely affecting repellency and may not be good for the stone. Use a neutral cleaner specially formulated for natural stone. For routine cleaning with protection: Revitalizer Cleaner & Protector concentrate mixed with warm or hot water as suggested below: Light Duty Usage 1 part Revitalizer Cleaner & Protector to 4 parts water. Medium Duty Usage/Spray Refill 1 part Revitalizer Cleaner & Protector to 1 part water. (One gallon of concentrate makes up to five gallons of ready-to-use solution.) 3 Apply the Revitalizer Cleaner & Protector solution using a low-pressure chemicalresistant sprayer, mop, sponge or automatic scrubbing machine. 4 No rinsing needed. 5 Or use Revitalizer Cleaner & Protector in a ready-to-use spray bottle or wipes. For routine maintenance cleaning: Stone & Tile Cleaner concentrate mixed with warm or hot water as suggested below: 2 ounces Stone & Tile Cleaner in 1 gallon of water. (Do not mix stronger than 2 ounces to a gallon as a maintenance cleaner. One gallon of concentrate makes 65 gallons of cleaning solution.) 3 Apply the solution using a sponge, mop or automatic scrubbing machine, then wipe or rinse off. 4 Or use Stone & Tile Cleaner in a ready-to-use spray bottle or wipes. 12

15 Polished Limestone READ ALL INSTRUCTIONS AND PRODUCT LABELS COMPLETELY BEFORE USING Pretest in an inconspicuous area prior to application to determine if the desired results will be achieved and that the stone is not adversely affected. NEW INSTALLATIONS Follow the recommended installation methods and procedures of the Marble Institute of America and the Tile Contractors Association. PRE-GROUTING For making grout clean up easier on porous stone: 2 Insure that surface temperature of the stone is between 50-80ºF. 3 Apply a single coat of StoneTech Professional Grout Release using a paint pad, low-pressure chemical-resistant sprayer, roller or brush. 4 Allow the Grout Release to completely penetrate the stone for 5-15 minutes. 5 Wipe up all remaining sealer from the surface of the stone. Do not allow pooling or sealer to dry on the surface. Do not over apply. 6 Allow for a minimum of 4 hours cure time prior to grouting. 7 After grouting, remove excess grout. Do not allow grout to completely dry prior to removal. 8 Expected coverage for Grout Release is sq. ft. per RESTORATIVE CLEANING Depending on the type of soil, stain or other foreign matter present, select one or more of the following options: For stripping off any existing topical acrylic, urethane, epoxy, heavy wax coatings and epoxy grout haze: 3 For heavy, hard to remove coatings, use a commercially available coating stripper. Follow instructions as indicated on bottle. For cleaning of grease, oil, dirt, dry soil and soap scum: 3 Strip off all topical finishes such as waxes and coatings. 4 Prepare a solution of StoneTech Professional KlenzAll mixed with warm or hot water as suggested below: Medium Duty Usage Mix 1 part of KlenzAll to 4 parts of water. Heavy Duty Usage Mix 1 part KlenzAll to 2 parts of water. 5 Apply KlenzAll using a low-pressure chemical-resistant sprayer, sponge or mop. 6 Agitate well using a stiff nylon bristle scrub brush, stiff bristle push broom or a weighted floor machine at 130 lbs.-140 lbs., 175 rpm, fitted with a scrub brush attachment. 7 Rinse well with clean water and mop, sponge or wet vacuum to remove the remaining cleaning solution. A hard surface extraction wand and portable or truck mounted extraction machine may be used. Repeat the rinsing and wet vacuum process to insure that all dirt, soil and cleaner residue have been removed. 8 To remove deep or stubborn oil stains not completely removed by KlenzAll, let the surface dry and use StoneTech Professional Oil Stain Remover. a Apply a ¼ inch thick coat of Oil Stain Remover to the oil stained area. Insure that Oil Stain Remover covers an area 1 to 2 beyond the stained area for the purpose of containment. b Allow 2-3 days for the Oil Stain Remover to dry to a powder. c Sweep and wipe up dried powder and evaluate the stained area for removal. d Repeat process if needed. e Remove any remaining Oil Stain Remover using mineral spirits. MECHANICAL REFINISHING OF POLISHED LIMESTONE For scratch, etch and wear pattern removal and to restore the surface to an even finish. Depending on the severity of the damage to the stone and/or the desired surface appearance, choose one or more of the grit levels of the StoneTech Professional Honing Powders 180/280/400/600/800, StoneTech Professional Polishing Powder and/or StoneTech Professional Shining Powder as appropriate. For refinishing to a honed finish: 3 Strip off all topical finishes such as waxes and coatings. 4 Liberally apply Honing Powder to the stone surface. 5 Add water to form a milk-like consistency. 6 Refinish using a hand orbital sander or weighted floor machine at 130 lbs.-140 lbs., 175 rpm, fitted with a natural hair pad. 7 Keep compound wet with plenty of water while refinishing. Add Honing Powder as needed. 8 Refinish area until the desired level of hone has been achieved. 9 Rinse well and use a wet vacuum to remove all excess compound. 10 Clean equipment with water. For refinishing to a polish: Use successively higher grits of Honing Powder to close the face of the stone. Follow with Polishing Powder as applicable. 3 Strip off all topical finishes such as waxes and coatings. 4 Liberally apply Polishing Powder to the stone surface. 5 Add water to form a milk-like consistency. 6 Refinish using a hand orbital sander or weighted floor machine at 130 lbs.-140 lbs., 175 rpm, fitted with a natural hair pad. 7 Keep compound wet with plenty of water while refinishing. Add Polishing Powder as needed. 8 Refinish area until the desired level of polish has been achieved. 9 Rinse well and use a wet vacuum to remove all excess compound. 10 Clean equipment with water. For a highly polished finish: Use Shining Powder as applicable. See Maintenance Polishing. Care Instructions SEALING & PROTECTING Natural stone surfaces must be sealed to prevent or minimize staining. Leaving natural stone untreated may greatly hinder the complete removal of stains in the future. The following suggestions are for impregnating the stone and will allow the stone to breathe. Allow new installations to cure for 72 hours prior to applying sealer. For a natural looking protector on interior and exterior surfaces (heavy duty protection, water and oil repellency): Option 1: Heavy duty protection, water-based formula: 3 Insure that surface is clean and residue-free. 4 StoneTech Professional Heavy Duty Sealer may be applied to damp surfaces one hour after standing water has been removed. 5 Liberally apply an even coat of sealer using a paint pad, low-pressure chemical-resistant sprayer, roller or brush. 6 Allow sealer to penetrate the surface for minutes. During this time, distribute excess over entire area to insure even penetration. Wipe off any remaining sealer prior to drying on the surface. StoneTech ProfessioNAL Stone & TILE CARE RESOURCE GUIDE /2007 Edition STONEHELP ( ) MARBLE GRANITE LIMESTONE TRAVERTINE SLATE 13

16 MARBLE GRANITE LIMESTONE TRAVERTINE SLATE 7 A second coat may be needed for porous, absorbent surfaces and should be applied minutes after initial application as directed in steps A minimum of 15 minutes after final application, wipe entire surface with a clean dry towel to remove any residue and excess sealer, if needed. 9 If sealer was not completely wiped off and a residue appears, wipe entire surface with 10 A full cure is achieved after hours; foot 11 Expected coverage is sq. ft. per 12 Re-application of Heavy Duty Sealer: A 1-3 year re-application is needed for exterior surfaces. Option 2: Heavy duty protection, solventbased formula: 3 Insure that surface is clean, dry and residuefree. 4 Ensure area is well-ventilated. Use a respirator if unsure that work area is well-ventilated. A NIOSH approved respirator with a combination HEPA/organic vapor cartridge is recommended. Follow respirator manufacturer s instructions for use. 5 Liberally apply an even coat of StoneTech Professional Impregnator Pro Sealer using a paint pad, roller, brush or pump-up garden sprayer. DO NOT USE A POWER SPRAYER. 6 Allow sealer to penetrate the surface for minutes; denser material may require more time for sealer to penetrate. During this time, distribute excess over entire area to insure even penetration. Wipe off any remaining sealer prior to drying on the surface. 7 A second coat may be needed for porous, absorbent surfaces and should be applied one hour after initial application as directed in steps If sealer was not completely wiped off and a residue appears, wipe entire surface with 9 A full cure is achieved after hours; foot 10 Expected coverage is sq. ft. per 11 Re-application of Impregnator Pro Sealer: A 1-3 year re-application is needed for exterior surfaces. WARNING: HARMFUL VAPORS. HARMFUL OR FATAL IF SWALLOWED. COMBUSTIBLE. KEEP OUT OF THE REACH OF CHILDREN. Do not ingest. Avoid contact with eyes and skin. Avoid exposure to vapors. Use in a well-ventilated area. For spray application: Use a pump-up garden sprayer. DO NOT USE A POWER SPRAYER. Use a respirator if unsure that work area is wellventilated. A NIOSH approved respirator with a combination HEPA/organic vapor cartridge is recommended. Follow respirator manufacturer s instructions for use. Do not freeze or store above 100 F/38 C. Do not mix with other chemicals. For a natural looking protector on exterior surfaces (heavy duty protection, water repellency only): StoneTech Professional Heavy Duty Exterior Sealer is a water repellent specially designed for exterior projects such as facades, cladding, pool decks, parking areas and driveways. It is very resistant to chemicals (i.e., chlorine) and to the effects of weather (i.e., ultraviolet light/sunlight, driving water/rain). 3 Insure that the surface is clean, dry and residue-free. 4 Liberally apply an even coat of Heavy Duty Exterior Sealer with a paint pad, brush, paint roller or low-pressure solvent-resistant sprayer. 5 Allow sealer to penetrate the surface for 5-15 minutes; denser material may require more time for sealer to penetrate. During this time, distribute excess over entire area to insure even penetration. Wipe off any remaining sealer prior to drying on the surface. 6 A second coat may be needed for porous, absorbent surfaces and should be applied one hour after initial application as directed in steps If sealer was not completely wiped off and a residue appears, wipe entire surface with 8 Do not walk on surface for at least 4-6 hours. Full cure is achieved in hours. 9 Expected coverage is sq. ft. per 10 Re-application of Heavy Duty Exterior Sealer: A 5-10 year re-application is recommended for exterior surfaces. MAINTENANCE CLEANING Highly alkaline, acidic, ammoniated, abrasive cleaners and/or bleach may break down the sealer, adversely affecting repellency and may not be good for the stone. Use a neutral cleaner specially formulated for natural stone. For routine cleaning with protection: Revitalizer Cleaner & Protector concentrate mixed with warm or hot water as suggested below: Light Duty Usage 1 part Revitalizer Cleaner & Protector to 4 parts water. Medium Duty Usage/Spray Refill 1 part Revitalizer Cleaner & Protector to 1 part water. (One gallon of concentrate makes up to five gallons of ready-to-use solution.) 3 Apply the Revitalizer Cleaner & Protector solution using a low-pressure chemicalresistant sprayer, mop, sponge or automatic scrubbing machine. 4 No rinsing needed. 5 Or use Revitalizer Cleaner & Protector in a ready-to-use spray bottle or wipes. For routine maintenance cleaning: Stone & Tile Cleaner concentrate mixed with warm or hot water as suggested below: 2 ounces Stone & Tile Cleaner in 1 gallon of water. (Do not mix stronger than 2 ounces to a gallon as a maintenance cleaner. One gallon of concentrate makes 65 gallons of cleaning solution.) 3 Liberally apply Shining Powder powder to the surface. 4 Or use Stone & Tile Cleaner in a ready-to-use spray bottle or wipes. MAINTENANCE POLISHING To maintain the shine and beauty of polished limestone on a routine basis and to minimize the need for restorative polishing: 3 Liberally apply Shining Powder powder to the surface. 4 Add enough water to form a milk-like consistency. 5 Refinish using a hand orbital sander or weighted floor machine at 130 lbs.-140 lbs., 175 rpm, fitted with a natural hair pad. 6 Rinse well and use a wet vacuum to remove all remaining compound. 7 Expected coverage is 750-1,500 sq. ft. per 1.5 lb. canister. 8 Re-application: Semi-annually or as needed. For a brilliant shine on countertops, vanities and vertical surfaces: 1 On a cleaned surface, spray a light coat of StoneTech Professional Polish over the entire surface. Do not spray in eyes. 2 Spread the polish evenly with a clean, white terry cloth towel. 3 Buff off polish. Keep turning the towel to insure that a clean section is being used for maximum efficiency. 4 Continue buffing until there is no visible polish left and high shine appears. 5 Reapplication as desired. Note: Polish will work best on stone previously sealed with StoneTech Professional sealers. 14

17 Unpolished, Honed & Textured Limestone READ ALL INSTRUCTIONS AND PRODUCT LABELS COMPLETELY BEFORE USING Pretest in an inconspicuous area prior to application to determine if the desired results will be achieved and that the stone is not adversely affected. NEW INSTALLATIONS Follow the recommended installation methods and procedures of the Marble Institute of America and the Tile Contractors Association. PRE-GROUTING For making grout clean up easier on porous stone: 2 Insure that surface temperature of the stone is between 50-80ºF. 3 Apply a single coat of StoneTech Professional Grout Release using a paint pad, low-pressure chemical-resistant sprayer, roller or brush. 4 Allow the Grout Release to completely penetrate the stone for 5-15 minutes. 5 Wipe up all remaining sealer from the surface of the stone. Do not allow pooling or sealer to dry on the surface. Do not over apply. 6 Allow for a minimum of 4 hours cure time prior to grouting. 7 After grouting, remove excess grout. Do not allow grout to completely dry prior to removal. 8 Expected coverage for Grout Release is sq. ft. per RESTORATIVE CLEANING Depending on the type of soil, stain or other foreign matter present, select one or more of the following options: For stripping off any existing topical acrylic, urethane, epoxy, heavy wax coatings and epoxy grout haze: 3 For heavy, hard to remove coatings, use a commercially available coating stripper. Follow instructions as indicated on bottle. For cleaning of grease, oil, dirt, dry soil and soap scum: 3 Strip off all topical finishes such as waxes and coatings. 4 Prepare a solution of StoneTech Professional KlenzAll mixed with warm or hot water as suggested below: Medium Duty Usage Mix 1 part of KlenzAll to 4 parts of water. Heavy Duty Usage Mix 1 part KlenzAll to 2 parts of water. 5 Apply KlenzAll using a low-pressure chemical-resistant sprayer, sponge or mop. 6 Agitate well using a stiff nylon bristle scrub brush, stiff bristle push broom or a weighted floor machine at 130 lbs.-140 lbs., 175 rpm, fitted with a scrub brush attachment. 7 Rinse well with clean water and mop, sponge or wet vacuum to remove the remaining cleaning solution. A hard surface extraction wand and portable or truck mounted extraction machine may be used. Repeat the rinsing and wet vacuum process to insure that all dirt, soil and cleaner residue have been removed. 8 To remove deep or stubborn oil stains not completely removed by KlenzAll, let the surface dry and use StoneTech Professional Oil Stain Remover. a Apply a ¼ inch thick coat of Oil Stain Remover to the oil stained area. Insure that Oil Stain Remover covers an area 1 to 2 beyond the stained area for the purpose of containment. b Allow 2-3 days for the Oil Stain Remover to dry to a powder. c Sweep and wipe up dried powder and evaluate the stained area for removal. d Repeat process if needed. e Remove any remaining Oil Stain Remover using mineral spirits. MECHANICAL REFINISHING OF HONED LIMESTONE For scratch, etch, wear pattern removal and to restore the surface to an even finish. Depending on the severity of the damage to the stone and/or the desired surface appearance, choose one or more of the grit levels of the StoneTech Professional Honing Powders 180/280/400/600/800. For refinishing to a honed finish: 3 Strip off all topical finishes such as waxes and coatings. 4 Liberally apply Honing Powder to the stone surface. 5 Add water to form a milk-like consistency. 6 Refinish using a hand orbital sander or weighted floor machine at 130 lbs.-140 lbs., 175 rpm, fitted with a natural hair pad. 7 Keep compound wet with plenty of water while refinishing. Add Honing Powder as needed. 8 Refinish area until the desired level of hone has been achieved. 9 Rinse well and use a wet vacuum to remove all compound. 10 Clean equipment with water. SEALING & PROTECTING Natural stone surfaces must be sealed to prevent or minimize staining. Leaving natural stone untreated may greatly hinder the complete removal of stains in the future. The following suggestions are for impregnating the stone and will allow the stone to breathe. Allow new installations to cure for 72 hours prior to applying sealer. For a natural looking protector on interior and exterior surfaces (heavy duty protection, water and oil repellency): Care Instructions Option 1: Heavy duty protection, water-based formula: 3 Insure that surface is clean and residue-free. 4 StoneTech Professional Heavy Duty Sealer may be applied to damp surfaces one hour after standing water has been removed. 5 Liberally apply an even coat of sealer using a paint pad, low-pressure chemical-resistant sprayer, roller or brush. 6 Allow sealer to penetrate the surface for minutes. During this time, distribute excess over entire area to insure even penetration. Wipe off any remaining sealer prior to drying on the surface. 7 A second coat may be needed for porous, absorbent surfaces and should be applied minutes after initial application as directed in steps A minimum of 15 minutes after final application, wipe entire surface with a clean dry towel to remove any residue and excess sealer, if needed. 9 If sealer was not completely wiped off and a residue appears, wipe entire surface with 10 A full cure is achieved after hours; foot 11 Expected coverage is sq. ft. per 12 Re-application of Heavy Duty Sealer: A 1-3 year re-application is needed for exterior surfaces. Option 2: Heavy duty protection, solventbased formula: 3 Insure that surface is clean, dry and residue-free. 4 Ensure area is well-ventilated. Use a respirator if unsure that work area is well-ventilated. A NIOSH approved respirator with a combination HEPA/organic vapor cartridge is recommended. Follow respirator manufacturer s instructions for use. 5 Liberally apply an even coat of StoneTech Professional Impregnator Pro Sealer using a paint pad, roller, brush or pump-up garden sprayer. DO NOT USE A POWER SPRAYER. 6 Allow sealer to penetrate the surface for minutes; denser material may require more time for sealer to penetrate. During this time, distribute excess over entire area to insure even penetration. Wipe off any remaining sealer prior to drying on the surface. 7 A second coat may be needed for porous, StoneTech ProfessioNAL Stone & TILE CARE RESOURCE GUIDE /2007 Edition STONEHELP ( ) MARBLE GRANITE LIMESTONE TRAVERTINE SLATE 15

18 MARBLE GRANITE LIMESTONE TRAVERTINE SLATE absorbent surfaces and should be applied one hour after initial application as directed in steps If sealer was not completely wiped off and a residue appears, wipe entire surface with 9 A full cure is achieved after hours; foot 10 Expected coverage is sq. ft. per 11 Re-application of Impregnator Pro Sealer: A 1-3 year re-application is needed for exterior surfaces. WARNING: HARMFUL VAPORS. HARMFUL OR FATAL IF SWALLOWED. COMBUSTIBLE. KEEP OUT OF THE REACH OF CHILDREN. Do not ingest. Avoid contact with eyes and skin. Avoid exposure to vapors. Use in a well-ventilated area. For spray application: Use a pump-up garden sprayer. DO NOT USE A POWER SPRAYER. Use a respirator if unsure that work area is wellventilated. A NIOSH approved respirator with a combination HEPA/organic vapor cartridge is recommended. Follow respirator manufacturer s instructions for use. Do not freeze or store above 100 F/38 C. Do not mix with other chemicals. For a natural looking protector on exterior surfaces (heavy duty protection, water repellency only): StoneTech Professional Heavy Duty Exterior Sealer is a water repellent specially designed for exterior projects such as facades, cladding, pool decks, parking areas and driveways. It is very resistant to chemicals (i.e., chlorine) and to the effects of weather (i.e., ultraviolet light/sunlight, driving water/rain). 3 Insure that the surface is clean, dry and residue-free. 4 Liberally apply an even coat of Heavy Duty Exterior Sealer with a brush, paint roller or low-pressure solvent-resistant sprayer. 5 Allow sealer to penetrate the surface for 5-15 minutes; denser material may require more time for sealer to penetrate. During this time, distribute excess over entire area to insure even penetration. Wipe off any remaining sealer prior to drying on the surface. 6 A second coat may be needed for porous, absorbent surfaces and should be applied one hour after initial application as directed in steps If sealer was not completely wiped off and a residue appears, wipe entire surface with 8 Do not walk on surface for at least 4-6 hours. Full cure is achieved in hours. 9 Expected coverage is sq. ft. per 10 Re-application of Heavy Duty Exterior Sealer: A 5-10 year re-application is recommended for exterior surfaces. For a color enhancing, impregnating (non-topical) protector on interior and exterior surfaces (heavy duty protection, water and oil repellency): 3 Insure that surface is clean, dry and residuefree. Surface temperature should be between 50 F and 80 F. 4 Ensure area is well-ventilated. Use a respirator if unsure that work area is well-ventilated. A NIOSH approved respirator with a combination HEPA/organic vapor cartridge is recommended. Follow respirator manufacturer s instructions for use. 5 Liberally apply an even coat of StoneTech Professional Enhancer Pro Sealer using a paint pad, roller, brush or pump-up garden sprayer. DO NOT USE A POWER SPRAYER. Ensure that Enhancer Pro is distributed evenly over the entire surface to ensure even penetration. Uneven penetration will result in a blotchy appearance. 6 Allow to penetrate the surface for minutes; denser material may require more time for Enhancer Pro to penetrate. During this time, distribute excess over entire area to insure even penetration. Completely wipe surface with a clean dry terrycloth towel. DO NOT ALLOW ENHANCER PRO TO DRY COMPLETELY ON SURFACE! Failure to remove enhancer from the surface may result in a film or residue that may need to be mechanically removed. 7 A second coat may be needed for porous, absorbent surfaces or if a darker appearance is required and should be applied one hour after initial application as directed in steps If sealer was not completely wiped off and a residue appears, wipe entire surface with a towel dampened with sealer. Use a white, 9 A full cure is achieved after hours; foot 10 Expected coverage is sq. ft. per 11 Re-application of Enhancer Pro : interior or exterior surfaces. WARNING: HARMFUL VAPORS. HARMFUL OR FATAL IF SWALLOWED. COMBUSTIBLE. KEEP OUT OF THE REACH OF CHILDREN. Do not ingest. Avoid contact with eyes and skin. Avoid exposure to vapors. Use in a well-ventilated area. For spray application: Use a pump-up garden sprayer. DO NOT USE A POWER SPRAYER. Use a respirator if unsure that work area is wellventilated. A NIOSH approved respirator with a combination HEPA/organic vapor cartridge is recommended. Follow respirator manufacturer s instructions for use. Do not freeze or store above 100 F/38 C. Do not mix with other chemicals. For a color enhancing, impregnating (non-topical) protector on interior surfaces (economical protection, water and oil repellency): 3 Insure that surface is clean, dry and residue-free. 4 Liberally apply an even coat of StoneTech Professional Enhancer using a paint pad, low-pressure chemical-resistant sprayer, roller or brush. 5 Allow to penetrate the surface for minutes; denser material may require maximum time for enhancer to penetrate. During this time, distribute excess over entire area to insure even penetration. Completely wipe surface dry. DO NOT ALLOW ENHANCER TO DRY COMPLETELY ON SURFACE! 6 A second coat may be needed for porous, absorbent surfaces or if a darker appearance is required and should be applied one hour after initial application as directed in steps If sealer was not completely wiped off and a residue appears, wipe entire surface with a towel dampened with sealer. Use a white, 8 A full cure is achieved after hours; foot 9 Expected coverage is sq. ft. per 10 Re-application of Enhancer: MAINTENANCE CLEANING Highly alkaline, acidic, ammoniated, abrasive cleaners and/or bleach may break down the sealer, adversely affecting repellency and may not be good for the stone. Use a neutral cleaner specially formulated for natural stone. For routine cleaning with protection: Revitalizer Cleaner & Protector concentrate mixed with warm or hot water as suggested below: Light Duty Usage 1 part Revitalizer Cleaner & Protector to 4 parts water. Medium Duty Usage/Spray Refill 1 part Revitalizer Cleaner & Protector to 1 part water. (One gallon of concentrate makes up to five gallons of ready-to-use solution.) 3 Apply the Revitalizer Cleaner & Protector solution using a low-pressure chemicalresistant sprayer, mop, sponge or automatic scrubbing machine. 4 No rinsing needed. 5 Or use Revitalizer Cleaner & Protector in a ready-to-use spray bottle or wipes. For routine maintenance cleaning: All Purpose Stone and Tile Cleaner concentrate mixed with warm or hot water as suggested below: 2 ounces Stone & Tile Cleaner in 1 gallon of water. (Do not mix stronger than 2 ounces to a gallon as a maintenance cleaner. One gallon of concentrate makes 65 gallons of cleaning solution.) 3 Apply the solution using a sponge, mop or automatic scrubbing machine, then wipe or rinse off. 4 Or use Stone & Tile Cleaner in a ready-to-use spray bottle or wipes. 16

19 Polished Travertine READ ALL INSTRUCTIONS AND PRODUCT LABELS COMPLETELY BEFORE USING Pretest in an inconspicuous area prior to application to determine if the desired results will be achieved and that the stone is not adversely affected. NEW INSTALLATIONS Follow the recommended installation methods and procedures of the Marble Institute of America and the Tile Contractors Association. PRE-GROUTING For making grout clean up easier on porous stone: 2 Insure that surface temperature of the stone is between 50-80ºF. 3 Apply a single coat of StoneTech Professional Grout Release using a paint pad, low-pressure chemical-resistant sprayer, roller or brush. 4 Allow the Grout Release to completely penetrate the stone for 5-15 minutes. 5 Wipe up all remaining sealer from the surface of the stone. Do not allow pooling or sealer to dry on the surface. Do not over apply. 6 Allow for a minimum of 4 hours cure time prior to grouting. 7 After grouting, remove excess grout. Do not allow grout to completely dry prior to removal. 8 Expected coverage for Grout Release is sq. ft. per RESTORATIVE CLEANING Depending on the type of soil, stain or other foreign matter present, select one or more of the following options: For stripping off any existing topical acrylic, urethane, epoxy, heavy wax coatings and epoxy grout haze: 3 For heavy, hard to remove coatings, use a commercially available coating stripper. Follow instructions as indicated on bottle. For cleaning of grease, oil, dirt, dry soil and soap scum: 3 Strip off all topical finishes such as waxes and coatings. 4 Prepare a solution of StoneTech Professional KlenzAll mixed with warm or hot water as suggested below: Medium Duty Usage Mix 1 part of KlenzAll to 4 parts of water. Heavy Duty Usage Mix 1 part KlenzAll to 2 parts of water. 5 Apply KlenzAll using a low-pressure chemical-resistant sprayer, sponge or mop. 6 Agitate well using a stiff nylon bristle scrub brush, stiff bristle push broom or a weighted floor machine at 130 lbs.-140 lbs., 175 rpm, fitted with a scrub brush attachment. 7 Rinse well with clean water and mop, sponge or wet vacuum to remove the remaining cleaning solution. A hard surface extraction wand and portable or truck mounted extraction machine may be used. Repeat the rinsing and wet vacuum process to insure that all dirt, soil and cleaner residue have been removed. 8 To remove deep or stubborn oil stains not completely removed by KlenzAll, let the surface dry and use StoneTech Professional Oil Stain Remover. a Apply a ¼ inch thick coat of Oil Stain Remover to the oil stained area. Insure that Oil Stain Remover covers an area 1 to 2 beyond the stained area for the purpose of containment. b Allow 2-3 days for the Oil Stain Remover to dry to a powder. c Sweep and wipe up dried powder and evaluate the stained area for removal. d Repeat process if needed. e Remove any remaining Oil Stain Remover using mineral spirits. MECHANICAL REFINISHING OF POLISHED TRAVERTINE For scratch, etch and wear pattern removal and to restore the surface to an even finish. Depending on the severity of the damage to the stone and/or the desired surface appearance, choose one or more of the grit levels of the StoneTech Professional Honing Powder 180/280/400/600/800, StoneTech Professional Polishing Powder and/or StoneTech Professional Shining Powder as appropriate. For refinishing to a honed finish: 3 Strip off all topical finishes such as waxes and coatings. 4 Liberally apply Honing Powder to the stone surface. 5 Add water to form a milk-like consistency. 6 Refinish using a hand orbital sander or weighted floor machine at 130 lbs.-140 lbs., 175 rpm, fitted with a natural hair pad. 7 Keep compound wet with plenty of water while refinishing. Add Honing Powder as needed. 8 Refinish area until the desired level of hone has been achieved. 9 Rinse well and use a wet vacuum to remove all excess compound. 10 Clean equipment with water. For refinishing to a polish: Use successively higher grits of Honing Powder to close the face of the stone. Follow with Polishing Powder as applicable. 3 Strip off all topical finishes such as waxes and coatings. 4 Liberally apply Polishing Powder to the stone surface. 5 Add water to form a milk-like consistency. 6 Refinish using a hand orbital sander or weighted floor machine at 130 lbs.-140 lbs., 175 rpm, fitted with a natural hair pad. 7 Keep compound wet with plenty of water while refinishing. Add Polishing Powder as needed. 8 Refinish area until the desired level of polish has been achieved. 9 Rinse well and use a wet vacuum to remove all excess compound. 10 Clean equipment with water. For a highly polished finish: Use Shining Powder as applicable. See Maintenance Polishing. Care Instructions SEALING & PROTECTING Natural stone surfaces must be sealed to prevent or minimize staining. Leaving natural stone untreated may greatly hinder the complete removal of stains in the future. The following suggestions are for impregnating the stone and will allow the stone to breathe. Allow new installations to cure for 72 hours prior to applying sealer. For a natural looking protector on interior and exterior surfaces (heavy duty protection, water and oil repellency): Option 1: Heavy duty protection, water-based formula: 3 Insure that surface is clean and residue-free. 4 StoneTech Professional Heavy Duty Sealer may be applied to damp surfaces one hour after standing water has been removed. 5 Liberally apply an even coat of sealer using a paint pad, low-pressure chemical-resistant sprayer, roller or brush. 6 Allow sealer to penetrate the surface for minutes. During this time, distribute excess over entire area to insure even penetration. Wipe off any remaining sealer prior to drying on the surface. 7 A second coat may be needed for porous, StoneTech ProfessioNAL Stone & TILE CARE RESOURCE GUIDE /2007 Edition STONEHELP ( ) MARBLE GRANITE LIMESTONE TRAVERTINE SLATE 17

20 MARBLE GRANITE LIMESTONE TRAVERTINE SLATE absorbent surfaces and should be applied minutes after initial application as directed in steps A minimum of 15 minutes after final application, wipe entire surface with a clean dry towel to remove any residue and excess sealer, if needed. 9 If sealer was not completely wiped off and a residue appears, wipe entire surface with a towel dampened with sealer. Use a white, 10 A full cure is achieved after hours; foot 11 Expected coverage is sq. ft. per 12 Re-application of Heavy Duty Sealer: A 1-3 year re-application is needed for exterior surfaces. Option 2: Heavy duty protection, solventbased formula: 3 Insure that surface is clean, dry and residuefree. 4 Ensure area is well-ventilated. Use a respirator if unsure that work area is well-ventilated. A NIOSH approved respirator with a combination HEPA/organic vapor cartridge is recommended. Follow respirator manufacturer s instructions for use. 5 Liberally apply an even coat of StoneTech Professional Impregnator Pro Sealer using a paint pad, roller, brush or pump-up garden sprayer. DO NOT USE A POWER SPRAYER. 6 Allow sealer to penetrate the surface for minutes; denser material may require more time for sealer to penetrate. During this time, distribute excess over entire area to insure even penetration. Wipe off any remaining sealer prior to drying on the surface. 7 A second coat may be needed for porous, absorbent surfaces and should be applied one hour after initial application as directed in steps If sealer was not completely wiped off and a residue appears, wipe entire surface with 9 A full cure is achieved after hours; foot 10 Expected coverage is sq. ft. per 11 Re-application of Impregnator Pro Sealer: A 1-3 year re-application is needed for exterior surfaces. WARNING: HARMFUL VAPORS. HARMFUL OR FATAL IF SWALLOWED. COMBUSTIBLE. KEEP OUT OF THE REACH OF CHILDREN. Do not ingest. Avoid contact with eyes and skin. Avoid exposure to vapors. Use in a well-ventilated area. For spray application: Use a pump-up garden sprayer. DO NOT USE A POWER SPRAYER. Use a respirator if unsure that work area is wellventilated. A NIOSH approved respirator with a combination HEPA/organic vapor cartridge is recommended. Follow respirator manufacturer s instructions for use. Do not freeze or store above 100 F/38 C. Do not mix with other chemicals. For a natural looking protector on exterior surfaces (heavy duty protection, water repellency only): StoneTech Professional Heavy Duty Exterior Sealer is a water repellent specially designed for exterior projects such as facades, cladding, [pool decks, parking areas and driveways. It is very resistant to chemicals (i.e., chlorine) and to the effects of weather (i.e., ultraviolet light/sunlight, driving water/rain). 3 Insure that the surface is clean, dry and residue-free. 4 Liberally apply an even coat of Heavy Duty Exterior Sealer with a paint pad, brush, paint roller or low-pressure solvent-resistant sprayer. 5 Allow sealer to penetrate the surface for 5-15 minutes; denser material may require more time for sealer to penetrate. During this time, distribute excess over entire area to insure even penetration. Wipe off any remaining sealer prior to drying on the surface. 6 A second coat may be needed for porous, absorbent surfaces and should be applied one hour after initial application as directed in steps If sealer was not completely wiped off and a residue appears, wipe entire surface with 8 Do not walk on surface for at least 4-6 hours. Full cure is achieved in hours. 9 Expected coverage is sq. ft. per 10 Re-application of Heavy Duty Exterior Sealer: A 5-10 year re-application is recommended for exterior surfaces. MAINTENANCE CLEANING Highly alkaline, acidic, ammoniated, abrasive cleaners and/or bleach may break down the sealer, adversely affecting repellency and may not be good for the stone. Use a neutral cleaner specially formulated for natural stone. For routine cleaning with protection: Revitalizer Cleaner & Protector concentrate mixed with warm or hot water as suggested below: Light Duty Usage 1 part Revitalizer Cleaner & Protector to 4 parts water. Medium Duty Usage/Spray Refill 1 part Revitalizer Cleaner & Protector to 1 part water. (One gallon of concentrate makes up to five gallons of ready-to-use solution.) 3 Apply the Revitalizer Cleaner & Protector solution using a low-pressure chemicalresistant sprayer, mop, sponge or automatic scrubbing machine. 4 No rinsing needed. 5 Or use Revitalizer Cleaner & Protector in a ready-to-use spray bottle or wipes. For routine maintenance cleaning: Stone & Tile Cleaner concentrate mixed with warm or hot water as suggested below: 2 ounces Stone & Tile Cleaner in 1 gallon of water. (Do not mix stronger than 2 ounces to a gallon as a maintenance cleaner. One gallon of concentrate makes 65 gallons of cleaning solution.) 3 Apply the solution using a sponge, mop or automatic scrubbing machine, then wipe or rinse off. 4 Or use Stone & Tile Cleaner in a ready-to-use spray bottle or wipes. MAINTENANCE POLISHING To maintain the shine and beauty of polished travertine on a routine basis and to minimize the need for restorative polishing: 3 Liberally apply Shining Powder to the surface. 4 Add enough water to form a milk-like consistency. 5 Refinish using a hand orbital sander or weighted floor machine at 130 lbs.-140 lbs., 175 rpm, fitted with a natural hair pad. 6 Rinse well and use a wet vacuum to remove all remaining compound. 7 Expected coverage is 750-1,500 sq. ft. per 1.5 lb. canister. 8 Re-application: Semi-annually or as needed. For a brilliant shine on countertops, vanities and vertical surfaces: 1 On a cleaned surface, spray a light coat of StoneTech Professional Polish over the entire surface. Do not spray in eyes. 2 Spread the polish evenly with a clean, white terry cloth towel. 3 Buff off polish. Keep turning the towel to insure that a clean section is being used for maximum efficiency. 4 Continue buffing until there is no visible polish left and high shine appears. 5 Reapplication as desired. Note: Polish will work best on stone previously sealed with StoneTech Professional sealers. 18

21 Unpolished, Honed & Textured Travertine READ ALL INSTRUCTIONS AND PRODUCT LABELS COMPLETELY BEFORE USING Pretest in an inconspicuous area prior to application to determine if the desired results will be achieved and that the stone is not adversely affected. NEW INSTALLATIONS Follow the recommended installation methods and procedures of the Marble Institute of America and the Tile Contractors Association. PRE-GROUTING For making grout clean up easier on porous stone: 2 Insure that surface temperature of the stone is between 50-80ºF. 3 Apply a single coat of StoneTech Professional Grout Release using a paint pad, low-pressure chemical-resistant sprayer, roller or brush. 4 Allow the Grout Release to completely penetrate the stone for 5-15 minutes. 5 Wipe up all remaining sealer from the surface of the stone. Do not allow pooling or sealer to dry on the surface. Do not over apply. 6 Allow for a minimum of 4 hours cure time prior to grouting. 7 After grouting, remove excess grout. Do not allow grout to completely dry prior to removal. 8 Expected coverage for Grout Release is sq. ft. per RESTORATIVE CLEANING Depending on the type of soil, stain or other foreign matter present, select one or more of the following options: For stripping off any existing topical acrylic, urethane, epoxy, heavy wax coatings and epoxy grout haze: 3 For heavy, hard to remove coatings, use a commercially available coating stripper. Follow instructions as indicated on bottle. For cleaning of grease, oil, dirt, dry soil and soap scum: 3 Strip off all topical finishes such as waxes and coatings. 4 Prepare a solution of StoneTech Professional KlenzAll mixed with warm or hot water as suggested below: Medium Duty Usage Mix 1 part of KlenzAll to 4 parts of water. Heavy Duty Usage Mix 1 part KlenzAll to 2 parts of water. 5 Apply KlenzAll using a low-pressure chemical-resistant sprayer, sponge or mop. 6 Agitate well using a stiff nylon bristle scrub brush, stiff bristle push broom or a weighted floor machine at 130 lbs.-140 lbs., 175 rpm, fitted with a scrub brush attachment. 7 Rinse well with clean water and mop, sponge or wet vacuum to remove the remaining cleaning solution. A hard surface extraction wand and portable or truck mounted extraction machine may be used. Repeat the rinsing and wet vacuum process to insure that all dirt, soil and cleaner residue have been removed. 8 To remove deep or stubborn oil stains not completely removed by KlenzAll, let the surface dry and use StoneTech Professional Oil Stain Remover. a Apply a ¼ inch thick coat of Oil Stain Remover to the oil stained area. Insure that Oil Stain Remover covers an area 1 to 2 beyond the stained area for the purpose of containment. b Allow 2-3 days for the Oil Stain Remover to dry to a powder. c Sweep and wipe up dried powder and evaluate the stained area for removal. d Repeat process if needed. e Remove any remaining Oil Stain Remover using mineral spirits. MECHANICAL REFINISHING OF HONED TRAVERTINE For scratch, etch, wear pattern removal and to restore the surface to an even finish. Depending on the severity of the damage to the stone and/or the desired surface appearance, choose one or more of the grit levels of the StoneTech Professional Honing Powder 180/280/400/600/800. For refinishing to a honed finish: 3 Strip off all topical finishes such as waxes and coatings. 4 Liberally apply Honing Powder to the stone surface. 5 Add water to form a milk-like consistency. 6 Refinish using a hand orbital sander or weighted floor machine at 130 lbs.-140 lbs., 175 rpm, fitted with a natural hair pad. 7 Keep compound wet with plenty of water while refinishing. Add Honing Powder as needed. 8 Refinish area until the desired level of hone has been achieved. 9 Rinse well and use a wet vacuum to remove all compound. 10 Clean equipment with water. SEALING & PROTECTING Natural stone surfaces must be sealed to prevent or minimize staining. Leaving natural stone untreated may greatly hinder the complete removal of stains in the future. The following suggestions are for impregnating the stone and will allow the stone to breathe. Allow new installations to cure for 72 hours prior to applying sealer. For a natural looking protector on interior and exterior surfaces (heavy duty protection, water and oil repellency): Care Instructions Option 1: Heavy duty protection, water-based formula: 3 Insure that surface is clean and residue-free. 4 StoneTech Professional Heavy Duty Sealer may be applied to damp surfaces one hour after standing water has been removed. 5 Liberally apply an even coat of sealer using a paint pad, low-pressure chemical-resistant sprayer, roller or brush. 6 Allow sealer to penetrate the surface for minutes. During this time, distribute excess over entire area to insure even penetration. Wipe off any remaining sealer prior to drying on the surface. 7 A second coat may be needed for porous, absorbent surfaces and should be applied minutes after initial application as directed in steps A minimum of 15 minutes after final application, wipe entire surface with a clean dry towel to remove any residue and excess sealer, if needed. 9 If sealer was not completely wiped off and a residue appears, wipe entire surface with 10 A full cure is achieved after hours; foot 11 Expected coverage is sq. ft. per 12 Re-application of Heavy Duty Sealer: A 1-3 year re-application is needed for exterior surfaces. Option 2: Heavy duty protection, solventbased formula: 3 Insure that surface is clean, dry and residuefree. 4 Ensure area is well-ventilated. Use a respirator if unsure that work area is well-ventilated. A NIOSH approved respirator with a combination HEPA/organic vapor cartridge is recommended. Follow respirator manufacturer s instructions for use. 5 Liberally apply an even coat of StoneTech Professional Impregnator Pro Sealer using a paint pad, roller, brush or pump-up garden sprayer. DO NOT USE A POWER SPRAYER. 6 Allow sealer to penetrate the surface for minutes; denser material may require more time for sealer to penetrate. During this time, distribute excess over entire area to insure even penetration. Wipe off any remaining sealer prior to drying on the surface. StoneTech ProfessioNAL Stone & TILE CARE RESOURCE GUIDE /2007 Edition STONEHELP ( ) MARBLE GRANITE LIMESTONE TRAVERTINE SLATE 19

22 MARBLE GRANITE LIMESTONE TRAVERTINE SLATE 7 A second coat may be needed for porous, absorbent surfaces and should be applied one hour after initial application as directed in steps If sealer was not completely wiped off and a residue appears, wipe entire surface with 9 A full cure is achieved after hours; foot 10 Expected coverage is sq. ft. per 11 Re-application of Impregnator Pro Sealer: A 1-3 year re-application is needed for exterior surfaces. WARNING: HARMFUL VAPORS. HARMFUL OR FATAL IF SWALLOWED. COMBUSTIBLE. KEEP OUT OF THE REACH OF CHILDREN. Do not ingest. Avoid contact with eyes and skin. Avoid exposure to vapors. Use in a well-ventilated area. For spray application: Use a pump-up garden sprayer. DO NOT USE A POWER SPRAYER. Use a respirator if unsure that work area is wellventilated. A NIOSH approved respirator with a combination HEPA/organic vapor cartridge is recommended. Follow respirator manufacturer s instructions for use. Do not freeze or store above 100 F/38 C. Do not mix with other chemicals. For a natural looking protector on exterior surfaces (heavy duty protection, water repellency only): StoneTech Professional Heavy Duty Exterior Sealer is a water repellent specially designed for exterior projects such as facades, cladding, pool decks, parking areas and driveways. It is very resistant to chemicals (i.e., chlorine) and to the effects of weather (i.e., ultraviolet light/sunlight, driving water/rain). 3 Insure that the surface is clean, dry and residue-free. 4 Liberally apply an even coat of Heavy Duty Exterior Sealer with a paint pad, brush, paint roller or low-pressure solvent-resistant sprayer. 5 Allow sealer to penetrate the surface for 5-15 minutes; denser material may require more time for sealer to penetrate. During this time, distribute excess over entire area to insure even penetration. Wipe off any remaining sealer prior to drying on the surface. 6 A second coat may be needed for porous, absorbent surfaces and should be applied one hour after initial application as directed in steps If sealer was not completely wiped off and a residue appears, wipe entire surface with 8 Do not walk on surface for at least 4-6 hours. Full cure is achieved in hours. 9 Expected coverage is sq. ft. per 10 Re-application of Heavy Duty Exterior Sealer: A 5-10 year re-application is recommended for exterior surfaces. For a color enhancing, impregnating (non-topical) protector on interior and exterior surfaces (heavy duty protection, water and oil repellency): 3 Insure that surface is clean, dry and residuefree. Surface temperature should be between 50 F and 80 F. 4 Ensure area is well-ventilated. Use a respirator if unsure that work area is well-ventilated. A NIOSH approved respirator with a combination HEPA/organic vapor cartridge is recommended. Follow respirator manufacturer s instructions for use. 5 Liberally apply an even coat of StoneTech Professional Enhancer Pro Sealer using a paint pad, roller, brush or pump-up garden sprayer. DO NOT USE A POWER SPRAYER. Ensure that Enhancer Pro is distributed evenly over the entire surface to ensure even penetration. Uneven penetration will result in a blotchy appearance. 6 Allow to penetrate the surface for minutes; denser material may require more time for Enhancer Pro to penetrate. During this time, distribute excess over entire area to insure even penetration. Completely wipe surface with a clean dry terrycloth towel. DO NOT ALLOW ENHANCER PRO TO DRY COMPLETELY ON SURFACE! Failure to remove enhancer from the surface may result in a film or residue that may need to be mechanically removed. 7 A second coat may be needed for porous, absorbent surfaces or if a darker appearance is required and should be applied one hour after initial application as directed in steps If sealer was not completely wiped off and a residue appears, wipe entire surface with 9 A full cure is achieved after hours; foot 10 Expected coverage is sq. ft. per 11 Re-application of Enhancer Pro : interior or exterior surfaces. WARNING: HARMFUL VAPORS. HARMFUL OR FATAL IF SWALLOWED. COMBUSTIBLE. KEEP OUT OF THE REACH OF CHILDREN. Do not ingest. Avoid contact with eyes and skin. Avoid exposure to vapors. Use in a well-ventilated area. For spray application: Use a pump-up garden sprayer. DO NOT USE A POWER SPRAYER. Use a respirator if unsure that work area is wellventilated. A NIOSH approved respirator with a combination HEPA/organic vapor cartridge is recommended. Follow respirator manufacturer s instructions for use. Do not freeze or store above 100 F/38 C. Do not mix with other chemicals. For a color enhancing, impregnating (non-topical) protector on interior surfaces (economical protection, water and oil repellency): 3 Insure that surface is clean, dry and residue-free. 4 Liberally apply an even coat of StoneTech Professional Enhancer using a paint pad, low-pressure chemical-resistant sprayer, roller or brush. 5 Allow to penetrate the surface for minutes; denser material may require maximum time for enhancer to penetrate. During this time, distribute excess over entire area to insure even penetration. Completely wipe surface dry. DO NOT ALLOW ENHANCER TO DRY COMPLETELY ON SURFACE! 6 A second coat may be needed for porous, absorbent surfaces or if a darker appearance is required and should be applied one hour after initial application as directed in steps A full cure is achieved after hours; foot 8 Expected coverage is sq. ft. per 9 Re-application of Enhancer: MAINTENANCE CLEANING Highly alkaline, acidic, ammoniated, abrasive cleaners and/or bleach may break down the sealer, adversely affecting repellency and may not be good for the stone. Use a neutral cleaner specially formulated for natural stone. For routine cleaning with protection: Revitalizer Cleaner & Protector Cleaner & Protector concentrate mixed with warm or hot water as suggested below: Light Duty Usage 1 part Revitalizer Cleaner & Protector Cleaner & Protector to 4 parts water. Medium Duty Usage/Spray Refill 1 part Revitalizer Cleaner & Protector Cleaner & Protector to 1 part water. (One gallon of concentrate makes up to five gallons of ready-to-use solution.) 3 Apply the Revitalizer Cleaner & Protector Cleaner & Protector solution using a lowpressure chemical-resistant sprayer, mop, sponge or automatic scrubbing machine. 4 No rinsing needed. 5 Or use Revitalizer Cleaner & Protector Cleaner & Protector in a ready-to-use spray bottle or wipes. For routine maintenance cleaning: Stone & Tile Cleaner concentrate mixed with warm or hot water as suggested below: 2 ounces Stone & Tile Cleaner in 1 gallon of water. (Do not mix stronger than 2 ounces to a gallon as a maintenance cleaner. One gallon of concentrate makes 65 gallons of cleaning solution.) 3 Apply the solution using a sponge, mop or automatic scrubbing machine, then wipe or rinse off. 4 Or use Stone & Tile Cleaner in a ready-to-use spray bottle or wipes. 20

23 Natural Slate READ ALL INSTRUCTIONS AND PRODUCT LABELS COMPLETELY BEFORE USING Pretest in an inconspicuous area prior to application to determine if the desired results will be achieved and that the stone is not adversely affected. NEW INSTALLATIONS Follow the recommended installation methods and procedures of the Marble Institute of America and the Tile Contractors Association. PRE-GROUTING For making grout clean up easier on porous stone: 2 Insure that surface temperature of the stone is between 50-80ºF. 3 Apply a single coat of StoneTech Professional Grout Release using a paint pad, low-pressure chemical-resistant sprayer, roller or brush. 4 Allow the Grout Release to completely penetrate the stone for 5-15 minutes. 5 Wipe up all remaining sealer from the surface of the stone. Do not allow pooling or sealer to dry on the surface. Do not over apply. 6 Allow for a minimum of 4 hours cure time prior to grouting. 7 After grouting, remove excess grout. Do not allow grout to completely dry prior to removal. 8 Expected coverage for Grout Release is sq. ft. per RESTORATIVE CLEANING Depending on the type of soil, stain or other foreign matter present, select one or more of the following options: For stripping off any existing topical acrylic, urethane, epoxy, heavy wax coatings and epoxy grout haze: 3 For heavy, hard to remove coatings, use a commercially available coating stripper. Follow instructions as indicated on bottle. For cleaning of grease, oil, dirt, dry soil and soap scum: 3 Strip off all topical finishes such as waxes and coatings. 4 Prepare a solution of StoneTech Professional KlenzAll mixed with warm or hot water as suggested below: Medium Duty Usage Mix 1 part KlenzAll to 4 parts of water. Heavy Duty Usage Mix 1 part KlenzAll to 2 parts of water. 5 Apply KlenzAll using a low-pressure chemical-resistant sprayer, sponge or mop. 6 Agitate well using a stiff nylon bristle scrub brush, stiff bristle push broom or a weighted floor machine at 110 lbs.-140 lbs., 175 rpm, fitted with a scrub brush attachment. Some softer slate may not require as much weight on the floor machine, up to lbs. may be sufficient. Test first, in an inconspicuous area, to insure that the slate surface is not being damaged. 7 Rinse well with clean water and mop, sponge or wet vacuum to remove the remaining cleaning solution. A hard surface extraction wand and portable or truck mounted extraction machine may be used. Repeat the rinsing and wet vacuum process to insure that all dirt, soil and cleaner residue have been removed. 8 To remove deep or stubborn oil stains not completely removed by KlenzAll, let the surface dry and use StoneTech Professional Oil Stain Remover. a Apply a ¼ inch thick coat of Oil Stain Remover to the oil stained area. Insure that Oil Stain Remover covers an area 1 to 2 beyond the stained area for the purpose of containment. b Allow 2-3 days for the Oil Stain Remover to dry to a powder. c Sweep and wipe up dried powder and evaluate the stained area for removal. d Repeat process if needed. e Remove any remaining Oil Stain Remover using mineral spirits. For removal of efflorescence, grout haze, salts, mineral deposits and all other calcium-based stains (acidic cleaning): Test in an inconspicuous area, as some materials are acid sensitive and may etch when acidic cleaners like StoneTech Professional Restore are applied. Restore may damage stainless steel and other surfaces. 3 Strip off all wax, acrylic, urethane and all topical finishes. 4 Prepare a solution of Restore mixed with warm or hot water as suggested below: Medium Duty Usage Mix 1 part of Restore to 4 parts of water. Heavy Duty Usage Mix 1 part of Restore to 1 part of water. 5 Liberally apply using a low-pressure chemicalresistant sprayer, sponge or mop. 6 Agitate well using a stiff nylon bristle scrub brush, stiff bristle push broom or a weighted floor machine at 110 lbs.-140 lbs., 175 rpm, fitted with a scrub brush attachment. Some softer slate may not require as much weight on the floor machine, up to lbs. may be sufficient. Test first, in an inconspicuous area, to insure that the slate surface is not being damaged. 7 Rinse well with clean water and mop, sponge or wet vacuum to remove the remaining solution. A hard surface extraction wand and portable or truck mounted extraction machine may be used. Repeat the rinsing and wet vacuum process to insure that all dirt, soil and cleaner residue have been removed. Thoroughly rinse all metal surfaces. SEALING & PROTECTING Care Instructions Natural stone surfaces must be sealed to prevent or minimize staining. Leaving natural stone untreated may greatly hinder the complete removal of stains in the future. The following suggestions are for impregnating the stone and will allow the stone to breathe. Allow new installations to cure for 72 hours prior to applying sealer. For a natural looking protector on interior and exterior surfaces (heavy duty protection, water and oil repellency): 3 Insure that surface is clean and residue-free. 4 StoneTech Professional Heavy Duty Sealer may be applied to damp surfaces one hour after standing water has been removed. 5 Liberally apply an even coat of sealer using a paint pad, low-pressure chemical-resistant sprayer, roller or brush. 6 Allow sealer to penetrate the surface for minutes. During this time, distribute excess over entire area to insure even penetration. Wipe off any remaining sealer prior to drying on the surface. 7 A second coat may be needed for porous, absorbent surfaces and should be applied minutes after initial application as directed in steps A minimum of 15 minutes after final application, wipe entire surface with a clean dry towel to remove any residue and excess sealer, if needed. 9 If sealer was not completely wiped off and a residue appears, wipe entire surface with 10 A full cure is achieved after hours; foot 11 Expected coverage is sq. ft. per 12 Re-application of Heavy Duty Sealer: A 1-3 year re-application is needed for exterior surfaces. For a natural looking protector on exterior surfaces (heavy duty protection, water repellency only): StoneTech Professional Heavy Duty Exterior Sealer is a water repellent specially designed for exterior projects such as facades, cladding, pool decks, parking areas and driveways. It is very resistant to chemicals (i.e., chlorine) and to the effects of weather (i.e., ultraviolet light/sunlight, driving water/rain). StoneTech ProfessioNAL Stone & TILE CARE RESOURCE GUIDE /2007 Edition STONEHELP ( ) MARBLE GRANITE LIMESTONE TRAVERTINE SLATE 21

24 MARBLE GRANITE LIMESTONE TRAVERTINE SLATE 3 Insure that the surface is clean, dry and residue-free. 4 Liberally apply an even coat of Heavy Duty Exterior Sealer with a paint pad, brush, paint roller or low-pressure solvent-resistant sprayer. 5 Allow sealer to penetrate the surface for 5-15 minutes; denser material may require more time for sealer to penetrate. During this time, distribute excess over entire area to insure even penetration. Wipe off any remaining sealer prior to drying on the surface. 6 A second coat may be needed for porous, absorbent surfaces and should be applied one hour after initial application as directed in steps If sealer was not completely wiped off and a residue appears, wipe entire surface with 8 Do not walk on surface for at least 4-6 hours. Full cure is achieved in hours. 9 Expected coverage is sq. ft. per 10 Re-application of Heavy Duty Exterior Sealer: A 5-10 year re-application is recommended for exterior surfaces. a well-ventilated area with an approved respirator device. For a color enhancing, impregnating (non-topical) protector on interior and exterior surfaces (heavy duty protection, water and oil repellency): Insure that surface is clean, dry and residue-free. Surface temperature should be between 50 F and 80 F. 3 Ensure area is well-ventilated. Use a respirator if unsure that work area is well-ventilated. A NIOSH approved respirator with a combination HEPA/organic vapor cartridge is recommended. Follow respirator manufacturer s instructions for use. 4 Liberally apply an even coat of StoneTech Professional Enhancer Pro Sealer using a paint pad, roller, brush or pump-up garden sprayer. DO NOT USE A POWER SPRAYER. Ensure that Enhancer Pro is distributed evenly over the entire surface to ensure even penetration. Uneven penetration will result in a blotchy appearance. 5 Allow to penetrate the surface for minutes; denser material may require more time for Enhancer Pro to penetrate. During this time, distribute excess over entire area to insure even penetration. Completely wipe surface with a clean dry terrycloth towel. DO NOT ALLOW ENHANCER PRO TO DRY COMPLETELY ON SURFACE! Failure to remove enhancer from the surface may result in a film or residue that may need to be mechanically removed. 6 A second coat may be needed for porous, absorbent surfaces or if a darker appearance is required and should be applied one hour after initial application as directed in steps A full cure is achieved after hours; foot 8 If sealer was not completely wiped off and a residue appears, wipe entire surface with 9 Expected coverage is sq. ft. per 10 Re-application of Enhancer Pro : interior or exterior surfaces. WARNING: HARMFUL VAPORS. HARMFUL OR FATAL IF SWALLOWED. COMBUSTIBLE. KEEP OUT OF THE REACH OF CHILDREN. Do not ingest. Avoid contact with eyes and skin. Avoid exposure to vapors. Use in a well-ventilated area. For spray application: Use a pump-up garden sprayer. DO NOT USE A POWER SPRAYER. Use a respirator if unsure that work area is wellventilated. A NIOSH approved respirator with a combination HEPA/organic vapor cartridge is recommended. Follow respirator manufacturer s instructions for use. Do not freeze or store above 100 F/38 C. Do not mix with other chemicals. For a color enhancing, impregnating (non-topical) protector on interior surfaces (economical protection, water and oil repellency): 3 Liberally apply an even coat of StoneTech Professional Enhancer using a paint pad, low-pressure chemical-resistant sprayer, roller or brush. 4 Allow to penetrate the surface for minutes; denser material may require maximum time for enhancer to penetrate. During this time, distribute excess over entire area to insure even penetration. Completely wipe surface dry. DO NOT ALLOW ENHANCER TO DRY COMPLETELY ON SURFACE! 5 A second coat may be needed for porous, absorbent surfaces or if a darker appearance is required and should be applied one hour after initial application as directed in steps A full cure is achieved after hours; foot 7 Expected coverage is sq. ft. per 8 Re-application of Enhancer: For a wet look, high gloss, color enhancing, topical protector on interior and exterior surfaces (maximum protection, water and oil repellency, resistant to acid etches): 1 Thoroughly pre-clean all debris, dirt, oil, grease and general stains from the surface using KlenzAll. Removes waxes, coatings, paint, and previously applied sealers first with a commercially available coating stripper. 2 Allow newly cleaned surface to completely dry prior to applying StoneTech Professional High Gloss Lacquer. 3 Mask off and protect any baseboards or 4 Avoid using in direct sunlight. Apply in air temperatures between 55 F to 80 F and on a cool dry surface. Use only in well ventilated area. 5 While wearing an organic vapor respirator, apply 2-3 even coats with a solvent-resistant natural hair bristle brush, roller or low pressure sprayer. 6 Allow 1-3 hours between coats or until surface is completely dry to the touch. 7 After final application, do not walk on surface until High Gloss Lacquer is completely cured. High Gloss Lacquer will cure in hours. 8 Clean up equipment with ordinary lacquer thinner, except as restricted by your local air quality management district. 9 Coverage varies depending on the porosity of the surface, method of application and desired thickness of coating. Approximately sq. ft. per 10 Re-application of High Gloss Lacquer: 1-3 years based upon wear. Note: Not recommended for areas with high moisture intrusion from below the surface, showers or counter tops. a well-ventilated area with an approved respirator device. MAINTENANCE CLEANING Highly alkaline, acidic, ammoniated, abrasive cleaners and/or bleach may break down the sealer, adversely affecting repellency and may not be good for the stone. Use a neutral cleaner specially formulated for natural stone. For routine cleaning with protection (not recommended for lacquered surfaces): Revitalizer Cleaner & Protector Cleaner & Protector concentrate 3 mixed with warm or hot water as suggested below: Light Duty Usage 1 part Revitalizer Cleaner & Protector Cleaner & Protector to 4 parts water. Medium Duty Usage/Spray Refill 1 part to 1 part water. (One gallon of concentrate makes up to five gallons of ready-touse solution.) 4 Apply the Revitalizer Cleaner & Protector solution using a low-pressure chemicalresistant sprayer, mop, sponge or automatic scrubbing machine. 5 No rinsing needed. 6 Or use Revitalizer Cleaner & Protector in a ready-to-use spray bottle or wipes. For routine maintenance cleaning: Stone & Tile Cleaner concentrate mixed with warm or hot water as suggested below: 2 ounces Stone & Tile Cleaner in 1 gallon of water. (Do not mix stronger than 2 ounces to a gallon as a maintenance cleaner. One gallon of concentrate makes 65 gallons of cleaning solution.) 3 Apply the solution using a sponge, mop or automatic scrubbing machine, then wipe or rinse off. 4 Or use Stone & Tile Cleaner in a ready-to-use spray bottle or wipes. 22

25 Sandstone & Flagstone READ ALL INSTRUCTIONS AND PRODUCT LABELS COMPLETELY BEFORE USING Pretest in an inconspicuous area prior to application to determine if the desired results will be achieved and that the stone is not adversely affected. NEW INSTALLATIONS Follow the recommended installation methods and procedures of the Marble Institute of America and the Tile Contractors Association. PRE-GROUTING For making grout clean up easier on cement brick: 2 Insure that surface temperature of the brick is between 50-80ºF. 3 Apply a single coat of StoneTech Professional Grout Release using a paint pad, low-pressure chemical-resistant sprayer, roller or brush. 4 Allow Grout Release to completely penetrate the surface for 5-15 minutes. 5 Wipe up all remaining sealer from the surface. Do not allow pooling or sealer to dry on the surface. Do not over apply. 6 Allow for a minimum of 4 hours cure time prior to grouting. 7 After grouting, remove excess grout. Do not allow grout to completely dry prior to removal. 8 Expected coverage for Grout Release is sq. ft. per RESTORATIVE CLEANING Depending on the type of soil, stain or other foreign matter present, select one or more of the following options: For stripping off any existing topical acrylic, urethane, epoxy, heavy wax coatings and epoxy grout haze: 3 For heavy, hard to remove coatings, use a commercially available coating stripper. Follow instructions as indicated on bottle. For cleaning of grease, oil, dirt, dry soil and soap scum: 3 Strip off all topical finishes such as waxes and coatings. 4 Prepare a solution of StoneTech Professional KlenzAll mixed with warm or hot water as suggested below: Medium Duty Usage Mix 1 part KlenzAll to 4 parts of water. Heavy Duty Usage Mix 1 part KlenzAll to 2 parts of water. 5 Apply KlenzAll using a low-pressure chemical-resistant sprayer, sponge or mop. 6 Agitate well using a stiff nylon bristle scrub brush, stiff bristle push broom or a weighted floor machine at 130 lbs.-140 lbs., 175 rpm, fitted with a scrub brush attachment. 7 Rinse well with clean water and mop, sponge or wet vacuum to remove the remaining cleaning solution. A hard surface extraction wand and portable or truck mounted extraction machine may be used. Repeat the rinsing and wet vacuum process to insure that all dirt, soil and cleaner residue have been removed. 8 To remove deep or stubborn oil stains not completely removed by KlenzAll, let the surface dry and use StoneTech Professional Oil Stain Remover. a Apply a ¼ inch thick coat of Oil Stain Remover to the oil stained area. Insure that Oil Stain Remover covers an area 1 to 2 beyond the stained area for the purpose of containment. b Allow 2-3 days for the Oil Stain Remover to dry to a powder. c Sweep and wipe up dried powder and evaluate the stained area for removal. d Repeat process if needed. e Remove any remaining Oil Stain Remover using mineral spirits. For removal of efflorescence, grout haze, salts, mineral deposits and all other calcium-based stains (acidic cleaning): Test in an inconspicuous area, as some materials are acid sensitive and may etch when acidic cleaners like StoneTech Professional Restore are applied. Restore may damage stainless steel and other metals. 3 Strip off all wax, acrylic, urethane and all topical finishes. 4 Prepare a solution of Restore mixed with warm or hot water as suggested below: Medium Duty Usage Mix 1 part of Restore to 4 parts of water. Heavy Duty Usage Mix 1 part of Restore to 1 part of water. 5 Liberally apply using a low-pressure chemicalresistant sprayer, sponge or mop. 6 Agitate well using a stiff nylon bristle scrub brush, stiff bristle push broom or a weighted floor machine at 130 lbs.-140 lbs., 175 rpm, fitted with a scrub brush attachment. 7 Rinse well with clean water and mop, sponge or wet vacuum to remove the remaining solution. A hard surface extraction wand and portable or truck mounted extraction machine may be used. Repeat the rinsing and wet vacuum process to insure that all dirt, soil and cleaner residue have been removed. Thoroughly rinse all metal surfaces. SEALING & PROTECTING Natural stone surfaces must be sealed to prevent or minimize staining. Leaving natural stone untreated may greatly hinder the complete removal of stains in the future. The following suggestions are for impregnating the stone and will allow the stone to breathe. Allow new installations to cure for 72 hours prior to applying sealer. Care Instructions For a natural looking protector on interior and exterior surfaces (heavy duty protection, water and oil repellency): 3 Insure that surface is clean and residue-free. 4 StoneTech Professional Heavy Duty Sealer may be applied to damp surfaces one hour after standing water has been removed. 5 Liberally apply an even coat of sealer using a paint pad, low-pressure chemical-resistant sprayer, roller or brush. 6 Allow sealer to penetrate the surface for minutes. During this time, distribute excess over entire area to insure even penetration. Wipe off any remaining sealer prior to drying on the surface. 7 A second coat may be needed for porous, absorbent surfaces and should be applied minutes after initial application as directed in steps A minimum of 15 minutes after final application, wipe entire surface with a clean dry towel to remove any residue and excess sealer, if needed. 9 If sealer was not completely wiped off and a residue appears, wipe entire surface with 10 A full cure is achieved after hours; foot 11 Expected coverage is sq. ft. per 12 Re-application of Heavy Duty Sealer: A 1-3 year re-application is needed for exterior surfaces. For a natural looking protector on exterior surfaces (heavy duty protection, water repellency only): StoneTech Professional Heavy Duty Exterior Sealer is a water repellent specially designed for exterior projects such as facades, cladding, pool decks, parking areas and driveways. It is very resistant to chemicals (i.e., chlorine) and to the effects of weather (i.e., ultraviolet light/sunlight, driving water/rain). 3 Insure that the surface is clean, dry and residue-free. 4 Liberally apply an even coat of Heavy Duty Exterior Sealer with a paint pad, brush, paint roller or low-pressure solvent-resistant sprayer. 5 Allow sealer to penetrate the surface for 5-15 minutes; denser material may require more time for sealer to penetrate. During this time, distribute excess over entire area to insure even penetration. StoneTech ProfessioNAL Stone & TILE CARE RESOURCE GUIDE /2007 Edition STONEHELP ( ) MARBLE GRANITE LIMESTONE TRAVERTINE SLATE 23

26 MARBLE GRANITE LIMESTONE TRAVERTINE SLATE 6 Wipe off any remaining sealer prior to drying on the surface. A second coat may be needed for porous, absorbent surfaces and should be applied one hour after initial application as directed in steps If sealer was not completely wiped off and a residue appears, wipe entire surface with 8 Do not walk on surface for at least 4-6 hours. Full cure is achieved in hours. 9 Expected coverage is sq. ft. per 10 Re-application of Heavy Duty Exterior Sealer: A 5-10 year re-application is recommended for exterior surfaces. For a color enhancing, impregnating (non-topical) protector on interior and exterior surfaces (heavy duty protection, water and oil repellency): Insure that surface is clean, dry and residue-free. Surface temperature should be between 50 F and 80 F. 3 Ensure area is well-ventilated. Use a respirator if unsure that work area is well-ventilated. A NIOSH approved respirator with a combination HEPA/organic vapor cartridge is recommended. Follow respirator manufacturer s instructions for use. 4 Liberally apply an even coat of StoneTech Professional Enhancer Pro Sealer using a paint pad, roller, brush or pump-up garden sprayer. DO NOT USE A POWER SPRAYER. Ensure that Enhancer Pro is distributed evenly over the entire surface to ensure even penetration. Uneven penetration will result in a blotchy appearance. 5 Allow to penetrate the surface for minutes; denser material may require more time for Enhancer Pro to penetrate. During this time, distribute excess over entire area to insure even penetration. Completely wipe surface with a clean dry terrycloth towel. DO NOT ALLOW ENHANCER PRO TO DRY COMPLETELY ON SURFACE! Failure to remove enhancer from the surface may result in a film or residue that may need to be mechanically removed. 6 A second coat may be needed for porous, absorbent surfaces or if a darker appearance is required and should be applied one hour after initial application as directed in steps If sealer was not completely wiped off and a residue appears, wipe entire surface with 8 A full cure is achieved after hours; foot 9 Expected coverage is sq. ft. per 10 Re-application of Enhancer Pro : interior or exterior surfaces. WARNING: HARMFUL VAPORS. HARMFUL OR FATAL IF SWALLOWED. COMBUSTIBLE. KEEP OUT OF THE REACH OF CHILDREN. Do not ingest. Avoid contact with eyes and skin. Avoid exposure to vapors. Use in a well-ventilated area. For spray application: Use a pump-up garden sprayer. DO NOT USE A POWER SPRAYER. Use a respirator if unsure that work area is wellventilated. A NIOSH approved respirator with a combination HEPA/organic vapor cartridge is recommended. Follow respirator manufacturer s instructions for use. Do not freeze or store above 100 F/38 C. Do not mix with other chemicals. For a color enhancing, impregnating (non-topical) protector on interior surfaces (economical protection, water and oil repellency): 3 Insure that surface is clean, dry and residuefree. 4 Liberally apply an even coat of StoneTech Professional Enhancer using a paint pad, low-pressure chemical-resistant sprayer, roller or brush. 5 Allow to penetrate the surface for minutes; denser material may require maximum time for enhancer to penetrate. During this time, distribute excess over entire area to insure even penetration. Completely wipe surface dry. DO NOT ALLOW ENHANCER TO DRY COMPLETELY ON SURFACE! 6 A second coat may be needed for porous, absorbent surfaces or if a darker appearance is required and should be applied one hour after initial application as directed in steps A full cure is achieved after hours; foot 8 Expected coverage is sq. ft. per Re-application of Enhancer: For a wet look, high gloss, color enhancing, topical protector on interior and exterior surfaces (maximum protection, water and oil repellency, resistant to acid etches): 1 Thoroughly pre-clean all debris, dirt, oil, grease and general stains from the surface using KlenzAll. Remove waxes, coatings, paint, and previously applied sealers first with a commercially available coating stripper. 2 Allow newly cleaned surface to completely dry prior to applying StoneTech Professional High Gloss Lacquer. 3 Mask off and protect any baseboards or 4 Avoid using in direct sunlight. Apply in air temperatures between 55 F to 80 F and on a cool dry surface. Use only in well ventilated area. 5 While wearing an organic vapor respirator, apply 2-3 even coats with a solvent-resistant natural hair bristle brush, roller or lowpressure sprayer. 6 Allow 1-3 hours between coats or until surface is completely dry to the touch. 7 After final application, do not walk on surface until High Gloss Lacquer is completely cured. High Gloss Lacquer will cure in hours. 8 Clean up equipment with ordinary lacquer thinner, except as restricted by your local air quality management district. 9 Coverage varies depending on the porosity of the surface, method of application and desired thickness of coating. Approximately sq. ft. per 10 Re-application of High Gloss Lacquer: 1-3 years based upon wear. Note: Not recommended for areas with high moisture intrusion from below the surface, showers or counter tops. a well-ventilated area with an approved respirator device. MAINTENANCE CLEANING Highly alkaline, acidic, ammoniated, abrasive cleaners and/or bleach may break down the sealer, adversely affecting repellency and may not be good for the stone. Use a neutral cleaner specially formulated for natural stone. For routine cleaning with protection (not recommended for lacquered surfaces): Revitalizer Cleaner & Protector concentrate mixed with warm or hot water as suggested below: Light Duty Usage 1 part Revitalizer Cleaner & Protector to 4 parts water. Medium Duty Usage/Spray Refill 1 part Revitalizer Cleaner & Protector to 1 part water. (One gallon of concentrate makes up to five gallons of ready-to-use solution.) 3 Apply the Revitalizer Cleaner & Protector solution using a low-pressure chemicalresistant sprayer, mop, sponge or automatic scrubbing machine. 4 No rinsing needed. 5 Or use Revitalizer Cleaner & Protector in a ready-to-use spray bottle or wipes. For routine maintenance cleaning: Stone & Tile Cleaner concentrate mixed with warm or hot water as suggested below: 2 ounces Stone & Tile Cleaner in 1 gallon of water. (Do not mix stronger than 2 ounces to a gallon as a maintenance cleaner. One gallon of concentrate makes 65 gallons of cleaning solution.) 3 Apply the solution using a sponge, mop or automatic scrubbing machine, then wipe or rinse off. 4 Or use Revitalizer Cleaner & Protector in a ready-to-use spray bottle or wipes. 24

27 Saltillo, Terra Cotta & Clay Brick READ ALL INSTRUCTIONS AND PRODUCT LABELS COMPLETELY BEFORE USING Pretest in an inconspicuous area prior to application to determine if the desired results will be achieved and that the stone is not adversely affected. NEW INSTALLATIONS Follow the recommended manufacturer s installation instructions and procedures. PRE-GROUTING For making grout clean up easier on porous tile and brick: 2 Insure that surface temperature is between 50-80ºF. 3 Apply a single coat of StoneTech Professional Grout Release using a paint pad, low-pressure chemical-resistant sprayer, roller or brush. 4 Allow Grout Release to completely penetrate the surface for 5-15 minutes. 5 Wipe up all remaining sealer from the surface. Do not allow pooling or sealer to dry on the surface. Do not over apply. 6 A second coat of Grout Release is recommended for raw Saltillo tile. 7 Allow for a minimum of 4 hours cure time prior to grouting. 8 After grouting, remove excess grout. Do not allow grout to completely dry prior to removal. 9 Expected coverage for Grout Release is sq. ft. per RESTORATIVE CLEANING Depending on the type of soil, stain or other foreign matter present, select one or more of the following options: For stripping off any existing topical acrylic, urethane, epoxy, heavy wax coatings and epoxy grout haze: 3 For heavy, hard to remove coatings, use a commercially available coating stripper. Follow instructions as indicated on bottle. For cleaning of grease, oil, dirt, dry soil and soap scum: 3 Strip off all topical finishes such as waxes and coatings. 4 Prepare a solution of StoneTech Professional KlenzAll mixed with warm or hot water as suggested below: Medium Duty Usage Mix 1 part KlenzAll to 4 parts of water. Heavy Duty Usage Mix 1 part KlenzAll to 2 parts of water. 5 Apply KlenzAll using a low-pressure chemical-resistant sprayer, sponge or mop. 6 Agitate well using a stiff nylon bristle scrub brush, stiff bristle push broom or a weighted floor machine at 110 lbs.-140 lbs., 175 rpm, fitted with a scrub brush attachment. 7 Rinse well with clean water and mop, sponge or wet vacuum to remove the remaining cleaning solution. A hard surface extraction wand and portable or truck mounted extraction machine may be used. Repeat the rinsing and wet vacuum process to insure that all dirt, soil and cleaner residue have been removed. 8 To remove deep or stubborn oil stains not completely removed by KlenzAll, let the surface dry and use StoneTech Professional Oil Stain Remover. a Apply a ¼ inch thick coat of Oil Stain Remover to the oil stained area. Insure that Oil Stain Remover covers an area 1 to 2 beyond the stained area for the purpose of containment. b Allow 2-3 days for the Oil Stain Remover to dry to a powder. c Sweep and wipe up dried powder and evaluate the stained area for removal. d Repeat process if needed. e Remove any remaining Oil Stain Remover using mineral spirits. For removal of efflorescence, grout haze, salts, mineral deposits and all other calcium-based stains (acidic cleaning): Test in an inconspicuous area, as some materials are acid sensitive and may etch when acidic cleaners like StoneTech Professional Restore are applied. Restore may damage stainless steel and other metals. Strip off all wax, acrylic, urethane and all topical finishes. 3 Prepare a solution of Restore mixed with warm or hot water as suggested below: Medium Duty Usage Mix 1 part of Restore to 4 parts of water. Heavy Duty Usage Mix 1 part of Restore to 1 part of water. 4 Liberally apply using a low-pressure chemicalresistant sprayer, sponge or mop. 5 Agitate well using a stiff nylon bristle scrub brush, stiff bristle push broom or a weighted floor machine at 110 lbs.-140 lbs., 175 rpm, fitted with a scrub brush attachment. 6 Rinse well with clean water and mop, sponge or wet vacuum to remove the remaining solution. A hard surface extraction wand and Care Instructions portable or truck mounted extraction machine may be used. 7 Repeat the rinsing and wet vacuum process to insure that all dirt, soil and cleaner residue have been removed. Thoroughly rinse all metal surfaces. SEALING & PROTECTING Clay surfaces must be sealed to prevent or minimize staining. Leaving clay surfaces unsealed may greatly hinder the complete removal of stains in the future. The following suggestions are for impregnating the surface and will allow the surface to breathe. Allow new installations to cure for 72 hours prior to applying sealer. For a natural looking protector on interior and exterior surfaces (maximum protection, water and oil repellency): 3 Insure that surface is clean and residue-free. 4 StoneTech Professional BulletProof Sealer may be applied to damp surfaces one hour after standing water has been removed. 5 Liberally apply an even coat of sealer using a paint pad, low-pressure chemical-resistant sprayer, roller or brush. 6 Allow sealer to penetrate the surface for minutes. During this time, distribute excess over entire area to insure even penetration. Wipe off any remaining sealer prior to drying on the surface. 7 A second coat may be needed for porous, absorbent surfaces and should be applied minutes after initial application as directed in steps A minimum of 15 minutes after final application, wipe entire surface with a towel dampened with sealer to remove any residue and excess sealer, if needed. 9 If sealer was not completely wiped off and a residue appears, wipe entire surface with 10 A full cure is achieved after hours; foot 11 Expected coverage is sq. ft. per 12 Re-application of BulletProof Sealer: A 1-3 year re-application is needed for exterior surfaces. StoneTech ProfessioNAL Stone & TILE CARE RESOURCE GUIDE /2007 Edition STONEHELP ( ) MARBLE GRANITE LIMESTONE TRAVERTINE SLATE 25

28 MARBLE GRANITE LIMESTONE TRAVERTINE SLATE For a natural looking protector on exterior surfaces (economical or heavy duty protection, water repellency only): These recommended sealers are specially designed for exterior projects such as facades, cladding, pool decks, parking areas and driveways. They are resistant to chemicals (i.e., chlorine) and to the effects of weather (i.e., ultraviolet light/ sunlight, driving water/rain). 3 Insure that the surface is clean, dry and residue-free. 4 Liberally apply one coat of StoneTech Professional Heavy Duty Exterior Sealer with a paint pad, brush, paint roller or low-pressure solvent-resistant sprayer. 5 Allow sealer to penetrate, about 5-15 minutes. 6 Allow first coat to cure for one hour. 7 Liberally apply a second coat as directed in steps Wipe off any remaining sealer prior to drying on surface. 9 If sealer was not completely wiped off and a residue appears, wipe entire surface with 10 Do not walk on surface for at least 4 hours. Full cure is achieved in 24 hours. 11 Expected coverage is sq. ft. per 12 Re-application of Heavy Duty Exterior Sealer: A 5-10 year re-application is recommended for exterior surfaces. For a color enhancing, impregnating (non-topical) protector on interior and exterior surfaces (heavy duty protection, water and oil repellency): Insure that surface is clean, dry and residue-free. Surface temperature should be between 50 F and 80 F. 3 Ensure area is well-ventilated. Use a respirator if unsure that work area is well-ventilated. A NIOSH approved respirator with a combination HEPA/organic vapor cartridge is recommended. Follow respirator manufacturer s instructions for use. 4 Liberally apply an even coat of StoneTech Professional Enhancer Pro Sealer using a paint pad, roller, brush or pump-up garden sprayer. DO NOT USE A POWER SPRAYER. Ensure that Enhancer Pro is distributed evenly over the entire surface to ensure even penetration. Uneven penetration will result in a blotchy appearance. 5 Allow to penetrate the surface for minutes; denser material may require maximum time for enhancer to penetrate. During this time, distribute excess over entire area to insure even penetration. Completely wipe surface with a clean dry terrycloth towel. DO NOT ALLOW ENHANCER PRO TO DRY COMPLETELY ON SURFACE! Failure to remove enhancer from the surface may result in a film or residue that may need to be mechanically removed. 6 A second coat is recommended for porous, absorbent surfaces or if a darker appearance is required and should be applied one hour after initial application as directed in steps If sealer was not completely wiped off and a residue appears, wipe entire surface with 8 A full cure is achieved after hours; foot 9 Expected coverage is sq. ft. per 10 Re-application of Enhancer Pro : interior or exterior surfaces. WARNING: HARMFUL VAPORS. HARMFUL OR FATAL IF SWALLOWED. COMBUSTIBLE. KEEP OUT OF THE REACH OF CHILDREN. Do not ingest. Avoid contact with eyes and skin. Avoid exposure to vapors. Use in a well-ventilated area. For spray application: Use a pump-up garden sprayer. DO NOT USE A POWER SPRAYER. Use a respirator if unsure that work area is wellventilated. A NIOSH approved respirator with a combination HEPA/organic vapor cartridge is recommended. Follow respirator manufacturer s instructions for use. Do not freeze or store above 100 F/38 C. Do not mix with other chemicals. For a wet look, high gloss, color enhancing, topical protector on interior and exterior surfaces (maximum protection, water and oil repellency, resistant to acid etches): 1 Thoroughly pre-clean all debris, dirt, oil, grease and general stains from the surface using KlenzAll. Remove waxes, coatings, paint, and previously applied sealers first with a commercially available coating stripper. 2 Allow newly cleaned surface to completely dry prior to applying StoneTech Professional High Gloss Lacquer. 3 Mask off and protect any baseboards or 4 Avoid using in direct sunlight. Apply in air temperatures between 55 F to 80 F and on a cool dry surface. Use only in well ventilated area. 5 While wearing an organic vapor respirator, apply 2-3 even coats with a solvent-resistant natural hair bristle brush, roller or lowpressure sprayer. More coats may be applied if desired. 6 Allow 1-3 hours between coats or until surface is completely dry to touch. 7 After final application, do not walk on surface until High Gloss Lacquer is completely cured. High Gloss Lacquer will cure in hours. 8 Clean up equipment with ordinary lacquer thinner, except as restricted by your local air quality management district. 9 Coverage varies depending on the porosity of the surface, method of application and desired thickness of coating. Approximately sq. ft. per 10 Re-application of High Gloss Lacquer: 1-3 years based upon wear. Note: Not recommended for areas with high moisture intrusion from below the surface, showers or counter tops. a well-ventilated area with an approved respirator device. MAINTENANCE CLEANING Highly alkaline, acidic, ammoniated, abrasive cleaners and/or bleach may break down the sealer, adversely affecting repellency and may not be good for the surface. Use a neutral cleaner specially formulated for clay surfaces. For routine cleaning with protection (not recommended for lacquered surfaces): Revitalizer Cleaner & Protector concentrate mixed with warm or hot water as suggested below: Light Duty Usage 1 part Revitalizer Cleaner & Protector to 4 parts water. Medium Duty Usage/Spray Refill 1 part Revitalizer Cleaner & Protector to 1 part water. (One gallon of concentrate makes up to five gallons of ready-to-use solution.) 3 Apply the Revitalizer Cleaner & Protector solution using a low-pressure chemicalresistant sprayer, mop, sponge or automatic scrubbing machine. 4 No rinsing needed. 5 Or use Revitalizer Cleaner & Protector in a ready-to-use spray bottle or wipes. For routine maintenance cleaning: Stone & Tile Cleaner concentrate mixed with warm or hot water as suggested below: 2 ounces Stone & Tile Cleaner in 1 gallon of water. (Do not mix stronger than 2 ounces to a gallon as a maintenance cleaner. One gallon of concentrate makes 65 gallons of cleaning solution.) 3 Apply the solution using a sponge, mop or automatic scrubbing machine, then wipe or rinse off. 4 Or use Stone & Tile Cleaner in a ready-to-use spray bottle or wipes. 26

29 Concrete, Stucco & Cementitious Brick READ ALL INSTRUCTIONS AND PRODUCT LABELS COMPLETELY BEFORE USING Pretest in an inconspicuous area prior to application to determine if the desired results will be achieved and that the stone is not adversely affected. NEW INSTALLATIONS Follow the recommended manufacturer s installation instructions and procedures. PRE-GROUTING For making grout clean up easier on cement brick: 2 Insure that surface temperature is between 50-80ºF. 3 Apply a single coat of StoneTech Professional Grout Release using a paint pad, low-pressure chemical-resistant sprayer, roller or brush. 4 Allow Grout Release to completely penetrate the surface for 5-15 minutes. 5 Wipe up all remaining sealer from the surface. Do not allow pooling or sealer to dry on the surface. Do not over apply. 6 A second coat of Grout Release is recommended for raw Saltillo tile. 7 Allow for a minimum of 4 hours cure time prior to grouting. 8 After grouting, remove excess grout. Do not allow grout to completely dry prior to removal. 9 Expected coverage for Grout Release is sq. ft. per RESTORATIVE CLEANING Depending on the type of soil, stain or other foreign matter present, select one or more of the following options: For stripping off any existing topical acrylic, urethane, epoxy, heavy wax coatings and epoxy grout haze: 3 For heavy, hard to remove coatings, use a commercially available coating stripper. Follow instructions as indicated on bottle. For cleaning of grease, oil, dirt, dry soil and soap scum: 3 Strip off all topical finishes such as waxes and coatings. 4 Prepare a solution of StoneTech Professional KlenzAll mixed with warm or hot water as suggested below: Medium Duty Usage Mix 1 part KlenzAll to 4 parts of water. Heavy Duty Usage Mix 1 part KlenzAll to 2 parts of water. 5 Apply KlenzAll using a low-pressure chemical-resistant sprayer, sponge or mop. 6 Agitate well using a stiff nylon bristle scrub brush, stiff bristle push broom or a weighted floor machine at 130 lbs.-140 lbs., 175 rpm, fitted with a scrub brush attachment. 7 Rinse well with clean water and mop, sponge or wet vacuum to remove the remaining cleaning solution. A hard surface extraction wand and portable or truck mounted extraction machine may be used. Repeat the rinsing and wet vacuum process to insure that all dirt, soil and cleaner residue have been removed. 8 To remove deep or stubborn oil stains not completely removed by KlenzAll, let the surface dry and use StoneTech Professional Oil Stain Remover. a Apply a ¼ inch thick coat of Oil Stain Remover to the oil stained area. Insure that Oil Stain Remover covers an area 1 to 2 beyond the stained area for the purpose of containment. b Allow 2-3 days for the Oil Stain Remover to dry to a powder. c Sweep and wipe up dried powder and evaluate the stained area for removal. d Repeat process if needed. e Remove any remaining Oil Stain Remover using mineral spirits. For removal of efflorescence, grout haze, salts, mineral deposits and all other calcium-based stains (acidic cleaning): Test in an inconspicuous area, as some materials are acid sensitive and may etch when acidic cleaners like StoneTech Professional Restore are applied. Restore may damage stainless steel and other metals. Strip off all wax, acrylic, urethane and all topical finishes. 3 Prepare a solution of Restore mixed with warm or hot water as suggested below: Light Duty Usage Mix 1 part of Restore to 16 parts of water. 4 Liberally apply using a low-pressure chemicalresistant sprayer, sponge or mop. 5 Agitate well using a stiff nylon bristle scrub brush, stiff bristle push broom or a weighted floor machine at 130 lbs.-140 lbs., 175 rpm, fitted with a scrub brush attachment. 6 Rinse well with clean water and mop, sponge or wet vacuum to remove the remaining solution. A hard surface extraction wand and portable or truck mounted extraction machine may be used. 7 Repeat the rinsing and wet vacuum process to insure that all dirt, soil and cleaner residue Care Instructions have been removed. Thoroughly rinse all metal surfaces. SEALING & PROTECTING Masonry surfaces must be sealed to prevent or minimize staining. Leaving many masonry surfaces unsealed may greatly hinder the complete removal of stains in the future. The following suggestions are for impregnating the surface and will allow the surface to breathe. Allow new installations to cure for 72 hours prior to applying sealer. Note: Because the specific composition of masonry products may vary, it is strongly recommended that a mock-up or pretest be performed to insure attainment of the desired results in both repellency and appearance. For a natural looking protector on interior and exterior surfaces (maximum protection, water and oil repellency): 3 Insure that surface is clean and residue-free. 4 StoneTech Professional BulletProof Sealer may be applied to damp surfaces one hour after standing water has been removed. 5 Liberally apply an even coat of sealer using a paint pad, low-pressure chemical-resistant sprayer, roller or brush. 6 Allow sealer to penetrate the surface for minutes. During this time, distribute excess over entire area to insure even penetration. Wipe off any remaining sealer prior to drying on the surface. 7 A second coat may be needed for porous, absorbent surfaces and should be applied minutes after initial application as directed in steps A minimum of 15 minutes after final application, wipe entire surface with a towel dampened with sealer to remove any residue and excess sealer, if needed. 9 If sealer was not completely wiped off and a residue appears, wipe entire surface with 10 A full cure is achieved after hours; foot 11 Expected coverage is sq. ft. per 12 Re-application of BulletProof Stone Sealer: A 1-3 year re-application is needed for exterior surfaces. StoneTech ProfessioNAL Stone & TILE CARE RESOURCE GUIDE /2007 Edition STONEHELP ( ) MARBLE GRANITE LIMESTONE TRAVERTINE SLATE 27

30 MARBLE GRANITE LIMESTONE TRAVERTINE SLATE For a natural looking protector on exterior surfaces (economical or heavy duty protection, water repellency only): These recommended sealers are specially designed for exterior projects such as facades, cladding, pool decks, parking areas and driveways. They are resistant to chemicals (i.e., chlorine) and to the effects of weather (i.e., ultraviolet light/ sunlight, driving water/rain). 3 Insure that the surface is clean, dry and residue-free. 4 Liberally apply one coat of StoneTech Professional Heavy Duty Exterior Sealer with a paint pad, brush, paint roller or low-pressure solvent-resistant sprayer. 5 Allow sealer to penetrate, about 5-15 minutes. 6 Allow first coat to cure for one hour. 7 Liberally apply a second coat as directed in steps Wipe off any remaining sealer prior to drying on surface. 9 If sealer was not completely wiped off and a residue appears, wipe entire surface with 10 Do not walk on surface for at least 4 hours. Full cure is achieved in 24 hours. 11 Expected coverage is sq. ft. per 12 Re-application of Heavy Duty Exterior Sealer: A 5-10 year re-application is recommended for exterior surfaces. For a color enhancing, impregnating (non-topical) protector on interior and exterior surfaces (heavy duty protection, water and oil repellency): 3 Insure that surface is clean, dry and residue-free. 4 Ensure area is well-ventilated. Use a respirator if unsure that work area is well-ventilated. A NIOSH approved respirator with a combination HEPA/organic vapor cartridge is recommended. Follow respirator manufacturer s instructions for use. 5 Liberally apply an even coat of StoneTech Professional Enhancer Pro Sealer using a paint pad, roller, brush or pump-up garden sprayer. DO NOT USE A POWER SPRAYER. Ensure that Enhancer Pro is distributed evenly over the entire surface to ensure even penetration. Uneven penetration will result in a blotchy appearance. 6 Allow to penetrate the surface for minutes; denser material may require maximum time for enhancer to penetrate. During this time, distribute excess over entire area to insure even penetration. Completely wipe surface with a clean dry terrycloth towel. DO NOT ALLOW ENHANCER PRO TO DRY COMPLETELY ON SURFACE! Failure to remove enhancer from the surface may result in a film or residue that may need to be mechanically removed. 7 A second coat is recommended for porous, absorbent surfaces or if a darker appearance is required and should be applied one hour after initial application as directed in steps If sealer was not completely wiped off and a residue appears, wipe entire surface with 9 A full cure is achieved after hours; foot 10 Expected coverage is sq. ft. per 11 Re-application of Enhancer Pro : interior or exterior surfaces. Note: Pretest Enhancer Pro in an inconspicuous area on concrete prior to application to ensure even results. Concrete can vary in porosity and can result in uneven enhancement. WARNING: HARMFUL VAPORS. HARMFUL OR FATAL IF SWALLOWED. COMBUSTIBLE. KEEP OUT OF THE REACH OF CHILDREN. Do not ingest. Avoid contact with eyes and skin. Avoid exposure to vapors. Use in a well-ventilated area. For spray application: Use a pump-up garden sprayer. DO NOT USE A POWER SPRAYER. Use a respirator if unsure that work area is wellventilated. A NIOSH approved respirator with a combination HEPA/organic vapor cartridge is recommended. Follow respirator manufacturer s instructions for use. Do not freeze or store above 100 F/38 C. Do not mix with other chemicals. For a wet look, high gloss, color enhancing, topical protector on interior and exterior surfaces (maximum protection, water and oil repellency, resistant to acid etches): 1 Thoroughly pre-clean all debris, dirt, oil, grease and general stains from the surface using KlenzAll. Remove waxes, coatings, paint, and previously applied sealers first with a commercially available coating stripper. 2 Allow newly cleaned surface to completely dry prior to applying StoneTech Professional High Gloss Lacquer. 3 Mask off and protect any baseboards or 4 Avoid using in direct sunlight. Apply in air temperatures between 55 F to 80 F and on a cool dry surface. Use only in well ventilated area. 5 While wearing an organic vapor respirator, apply 2-3 even coats with a solvent-resistant natural hair bristle brush, roller or low- pressure sprayer. More coats may be applied if desired. 6 Allow 1-3 hours between coats or until surface is completely dry to touch. 7 After final application, do not walk on surface until High Gloss Lacquer is completely cured. High Gloss Lacquer will cure in hours. 8 Clean up equipment with ordinary lacquer thinner, except as restricted by your local air quality management district. 9 Coverage varies depending on the porosity of the surface, method of application and desired thickness of coating. Approximately sq. ft. per 10 Re-application of High Gloss Lacquer: 1-3 years based upon wear. Note: Not recommended for areas with high moisture intrusion from below the surface, showers or counter tops. a well-ventilated area with an approved respirator device. MAINTENANCE CLEANING Highly alkaline, acidic, ammoniated, abrasive cleaners and/or bleach may break down the sealer, adversely affecting repellency and may not be good for the surface. Use a neutral cleaner specially formulated for clay surfaces. For routine cleaning with protection (not recommended for lacquered surfaces): Revitalizer Cleaner & Protector concentrate mixed with warm or hot water as suggested below: Light Duty Usage 1 part Revitalizer Cleaner & Protector to 4 parts water. Medium Duty Usage/Spray Refill 1 part Revitalizer Cleaner & Protector to 1 part water. (One gallon of concentrate makes up to five gallons of ready-to-use solution.) 3 Apply the Revitalizer Cleaner & Protector solution using a low-pressure chemicalresistant sprayer, mop, sponge or automatic scrubbing machine. 4 No rinsing needed. 5 Or use Revitalizer Cleaner & Protector in a ready-to-use sprayer or wipes. For routine maintenance cleaning: Stone & Tile Cleaner concentrate mixed with warm or hot water as suggested below: 2 ounces Stone & Tile Cleaner in 1 gallon of water. (Do not mix stronger than 2 ounces to a gallon as a maintenance cleaner. One gallon of concentrate makes 65 gallons of cleaning solution.) 3 Apply the solution using a sponge, mop or automatic scrubbing machine, then wipe or rinse off. 4 Or use Stone & Tile Cleaner in a ready-to-use spray bottle or wipes. 28

31 Ceramic, Porcelain & Quarry Tile with Cement-based Grout READ ALL INSTRUCTIONS AND PRODUCT LABELS COMPLETELY BEFORE USING Pretest in an inconspicuous area prior to application to determine if the desired results will be achieved and that the stone is not adversely affected. NEW INSTALLATIONS Follow the recommended installation methods and procedures of the Tile Contractors Association. PRE-GROUTING Most glazed ceramic and porcelain tile do not need a grout release process to make grout clean up easier. However, unglazed porcelain tile may sometimes need a grout release process because grout and color pigments can nestle themselves within the surface pores. 2 Insure that surface temperature of the tile is between 50-80ºF. 3 Apply a light coat of StoneTech Professional Grout Sealer using a paint pad, low-pressure chemical-resistant sprayer, roller or brush across the surface of the tile. 4 Allow the Grout Sealer to completely penetrate the tile for 5-15 minutes. 5 Wipe up all remaining sealer from the surface. Do not allow pooling or sealer to dry on the surface. Do not over apply. 6 Allow for a minimum of 2 hours cure time prior to grouting. 7 After grouting, remove excess grout. Do not allow grout to completely dry prior to removal. 8 Expected coverage for Grout Sealer is 1,000-1,500 sq. ft. per RESTORATIVE CLEANING Depending on the type of soil, stain or other foreign matter present, select one or more of the following options: For stripping off any existing topical acrylic, urethane, epoxy, heavy wax coatings and epoxy grout haze: 3 For heavy, hard to remove coatings, use a commercially available coating stripper. Follow instructions as indicated on bottle. For cleaning of grease, oil, dirt, dry soil and soap scum: 3 Strip off all topical finishes such as waxes and coatings. 4 Prepare a solution of StoneTech Professional KlenzAll mixed with warm r hot water as suggested below: Medium Duty Usage Mix 1 part KlenzAll to 4 parts of water. Heavy Duty Usage Mix 1 part KlenzAll to 2 parts of water. 5 Apply KlenzAll using a low-pressure chemical-resistant sprayer, sponge or mop. 6 Agitate well using a stiff nylon bristle scrub brush, stiff bristle push broom or a weighted floor machine at 130 lbs.-140 lbs., 175 rpm, fitted with a scrub brush attachment. 7 Rinse well with clean water and mop, sponge or wet vacuum to remove the remaining cleaning solution. A hard surface extraction wand and portable or truck mounted extraction machine may be used. Repeat the rinsing and wet vacuum process to insure that all dirt, soil and cleaner residue have been removed. 8 To remove deep or stubborn oil stains not completely removed by KlenzAll, let the surface dry and use StoneTech Professional Oil Stain Remover. a Apply a ¼ inch thick coat of Oil Stain Remover to the oil stained area. Insure that Oil Stain Remover covers an area 1 to 2 beyond the stained area for the purpose of containment. b Allow 2-3 days for the Oil Stain Remover to dry to a powder. c Sweep and wipe up dried powder and evaluate the stained area for removal. d Repeat process if needed. e Remove any remaining Oil Stain Remover using mineral spirits. For removal of efflorescence, grout haze, salts, mineral deposits and all other calcium-based stains (acidic cleaning): Test in an inconspicuous area to determine if the desired results will be achieved. Restore may damage stainless steel and other surfaces. 3 Strip off all wax, acrylic, urethane and all topical finishes. 4 Prepare a solution of Restore mixed with warm or hot water as suggested below: Medium Duty Usage Mix 1 part of Restore to 4 parts of water. Heavy Duty Usage Mix 1 part of Restore to 1 part of water. 5 Liberally apply using a low-pressure chemicalresistant sprayer, sponge or mop. 6 Agitate well using a stiff nylon bristle scrub brush, stiff bristle push broom or a weighted floor machine at 130 lbs.-140 lbs., 175 rpm, fitted with a scrub brush attachment. 7 Rinse well with clean water and mop, sponge or wet vacuum to remove the remaining Care Instructions solution. A hard surface wand and portable or truck mounted extraction machine may be used for this process. Repeat the rinsing and wet vacuum process to insure that all dirt, soil and cleaner residues have been removed. Thoroughly rinse all metal surfaces. SEALING & PROTECTING Cementitious grout must be sealed to prevent or minimize staining. Leaving these surfaces unsealed may greatly hinder the ability to completely remove stains in the future. Allow new installations to cure for 72 hours prior to applying sealer. For a natural looking protector on interior and exterior surfaces (heavy duty protection, water and oil repellency): 3 Insure that the surface is clean, dry and residue-free. 4 Liberally apply StoneTech Professional Grout Sealer using a paint pad, low-pressure chemical-resistant sprayer, narrow roller or natural hairbrush, focusing on the grout joints. 5 Allow sealer to completely penetrate into the grout, 5-15 minutes. 6 Liberally apply a second coat of Grout Sealer following steps Wipe up all sealer from the surface of the tile. Use a clean, dry, lint-free, cotton towel or mop to remove excess sealer. 8 If sealer was not completely wiped off and a residue appears, wipe entire surface with 9 A full cure is achieved after hours; foot traffic may begin in 4 hours. Cover with red rosin paper, if foot traffic must resume before the recommended time periods have passed. 10 Expected coverage is 600-1,000 sq. ft. per gallon based upon grout joint width. 11 Re-application of Grout Sealer: A 1-3 year re-application is needed for exterior surfaces. MAINTENANCE CLEANING Highly alkaline, acidic, ammoniated, abrasive cleaners and/or bleach may break down the sealer, adversely affecting repellency and may not be good for the grout. Use a neutral cleaner specially formulated for tile and grout. For routine maintenance cleaning: StoneTech ProfessioNAL Stone & TILE CARE RESOURCE GUIDE /2007 Edition STONEHELP ( ) MARBLE GRANITE LIMESTONE TRAVERTINE SLATE 29

32 SLATE TRAVERTINE LIMESTONE GRANITE MARBLE Stone & Tile Cleaner concentrate mixed with warm or hot water as suggested below: 2 ounces Stone & Tile Cleaner in 1 gallon of water. (Do not mix stronger than 2 ounces to a gallon as a maintenance cleaner. One gallon of concentrate makes 65 gallons of cleaning solution.) 3 Apply the solution using a sponge, mop or automatic scrubbing machine, then wipe or rinse off. 4 Or use Stone & Tile Cleaner in a ready-to-use spray bottle or wipes. For routine cleaning with protection: Revitalizer Cleaner & Protector concentrate mixed with warm or hot water as suggested below: Light Duty Usage 1 part Revitalizer Cleaner & Protector to 4 parts water. Medium Duty Usage/Spray Refill 1 part Revitalizer Cleaner & Protector to 1 part water. (One gallon of concentrate makes up to five gallons of ready-to-use solution.) 3 Apply the Revitalizer Cleaner & Protector solution using a low-pressure chemicalresistant sprayer, mop, sponge or automatic scrubbing machine. 4 No rinsing needed. 5 Or use Revitalizer Cleaner & Protector in a ready-to-use spray bottle or wipes. 30

33 Ceramic, Porcelain & Quarry Tile with Epoxy-based Grout READ ALL INSTRUCTIONS AND PRODUCT LABELS COMPLETELY BEFORE USING Pretest in an inconspicuous area prior to application to determine if the desired results will be achieved and that the stone is not adversely affected. NEW INSTALLATIONS Follow the recommended installation methods and procedures of the Tile Contractors Association. PRE-GROUTING Most glazed ceramic and porcelain tile do not need a grout release process to make grout clean up easier. However, unglazed porcelain tile may sometimes need a grout release process because grout and color pigments can nestle themselves within the surface pores. 2 Insure that surface temperature of the tile is between 50-80F. 3 Apply a light coat of StoneTech Professional Grout Sealer using a paint pad, low-pressure chemical-resistant sprayer, roller or brush across the surface of the tile. 4 Allow the Grout Sealer to completely penetrate the tile for 5-15 minutes. 5 Wipe up all remaining sealer from the surface. Do not allow pooling or sealer to dry on the surface. Do not over apply. 6 Allow for a minimum of 2 hours cure time prior to grouting. 7 After grouting, remove excess grout. Do not allow grout to completely dry prior to removal. 8 Expected coverage for Grout Sealer is 1,000-1,500 sq. ft. per RESTORATIVE CLEANING Depending on the type of soil, stain or other foreign matter present, select one or more of the following options: For stripping off any existing topical acrylic, urethane, epoxy, heavy wax coatings and epoxy grout haze: 3 For heavy, hard to remove coatings, use a commercially available coating stripper. Follow instructions as indicated on bottle. For cleaning of grease, oil, dirt, dry soil and soap scum: 3 Strip off all topical finishes such as waxes and coatings. 4 Prepare a solution of StoneTech Professional KlenzAll mixed with warm or hot water as suggested below: Medium Duty Usage Mix 1 part KlenzAll to 4 parts of water. Heavy Duty Usage Mix 1 part KlenzAll to 2 parts of water. 5 Apply KlenzAll using a low-pressure chemical-resistant sprayer, sponge or mop. 6 Agitate well using a stiff nylon bristle scrub brush, stiff bristle push broom or a weighted floor machine at 130 lbs.-140 lbs., 175 rpm, fitted with a scrub brush attachment. 7 Rinse well with clean water and mop, sponge or wet vacuum to remove the remaining cleaning solution. A hard surface extraction wand and portable or truck mounted extraction machine may be used. Repeat the rinsing and wet vacuum process to insure that all dirt, soil and cleaner residue have been removed. Care Instructions For removal of efflorescence, grout haze, salts, mineral deposits and all other calcium-based stains (acidic cleaning): Test in an inconspicuous area to determine if the desired results will be achieved. Restore may damage stainless steel and other surfaces. 3 Strip off all wax, acrylic, urethane and all topical finishes. 4 Prepare a solution of Restore mixed with warm or hot water as suggested below: Medium Duty Usage Mix 1 part of Restore to 4 parts of water. Heavy Duty Usage Mix 1 part of Restore to 1 part of water. Liberally apply using a low-pressure chemicalresistant sprayer, sponge or mop. 5 Agitate well using a stiff nylon bristle scrub brush, stiff bristle push broom or a weighted floor machine at 130 lbs.-140 lbs., 175 rpm, fitted with a scrub brush attachment. 6 Rinse well with clean water and mop, sponge or wet vacuum to remove the remaining solution. A hard surface wand and portable or truck mounted extraction machine may be used for this process. Repeat the rinsing and wet vacuum process to insure that all dirt, soil and cleaner residues have been removed. Thoroughly rinse all metal surfaces. MARBLE GRANITE LIMESTONE TRAVERTINE SLATE StoneTech ProfessioNAL Stone & TILE CARE RESOURCE GUIDE /2007 Edition STONEHELP ( ) 31

34 TRAVERTINE LIMESTONE GRANITE MARBLE SEALING & PROTECTING Epoxy grout, ceramic, porcelain & quarry tile are generally impervious to liquid stains from both oil and water-based materials and do not require sealing. Maintenance cleaning is required for dirt and dry soil removal. MAINTENANCE CLEANING Use a neutral cleaner specially formulated for tile & grout. For routine maintenance cleaning: Stone & Tile Cleaner concentrate mixed with warm or hot water as suggested below: 2 ounces Stone & Tile Cleaner in 1 gallon of water. (Do not mix stronger than 2 ounces to a gallon as a maintenance cleaner. One gallon of concentrate makes 65 gallons of cleaning solution.) 3 Apply the solution using a sponge, mop or automatic scrubbing machine, then wipe or rinse off. 4 Or use Stone & Tile Cleaner in a ready-to-use spray bottle or wipes. SLATE 32

35 Cantera and Adoquin READ ALL INSTRUCTIONS AND PRODUCT LABELS COMPLETELY BEFORE USING Pretest in an inconspicuous area prior to application to determine if the desired results will be achieved and that the stone is not adversely affected. NEW INSTALLATIONS Follow the recommended installation methods and procedures of the Marble Institute of America and the Tile Contractors Association. PRE-GROUTING For making grout clean up easier on porous stone: 2 Insure that surface temperature of the stone is between 50-80ºF. 3 Apply a single coat of StoneTech Professional Grout Release using a paint pad, low-pressure chemical-resistant sprayer, roller or brush. 4 Allow the Grout Release to completely penetrate the stone for 5-15 minutes. 5 Wipe up all remaining sealer from the surface of the stone. Do not allow pooling or sealer to dry on the surface. Do not over apply. 6 Allow for a minimum of 4 hours cure time prior to grouting. 7 After grouting, remove excess grout. Do not allow grout to completely dry prior to removal. 8 Expected coverage for Grout Release is sq. ft. per RESTORATIVE CLEANING Depending on the type of soil, stain or other foreign matter present, select one or more of the following options: For stripping off any existing topical acrylic, urethane, epoxy, heavy wax coatings and epoxy grout haze: 3 For heavy, hard to remove coatings, use a commercially available coating stripper. Follow instructions as indicated on bottle. a well-ventilated area with an approved respirator device. For cleaning of grease, oil, dirt, dry soil and soap scum: 3 Strip off all topical finishes such as waxes and coatings. 4 Prepare a solution of StoneTech Professional KlenzAll mixed with warm or hot water as suggested below: Medium Duty Usage Mix 1 part KlenzAll to 4 parts of water. Heavy Duty Usage Mix 1 part KlenzAll to 2 parts of water. 5 Apply KlenzAll using a low-pressure chemical-resistant sprayer, sponge or mop. 6 Agitate well using a stiff nylon bristle scrub brush, stiff bristle push broom or a weighted floor machine at 130 lbs.-140 lbs., 175 rpm, fitted with a scrub brush attachment. 7 Rinse well with clean water and mop, sponge or wet vacuum to remove the remaining cleaning solution. A hard surface extraction wand and portable or truck mounted extraction machine may be used. Repeat the rinsing and wet vacuum process to insure that all dirt, soil and cleaner residue have been removed. 8 To remove deep or stubborn oil stains not completely removed by KlenzAll, let the surface dry and use StoneTech Professional Oil Stain Remover. a Apply a ¼ inch thick coat of Oil Stain Remover to the oil stained area. Insure that Oil Stain Remover covers an area 1 to 2 beyond the stained area for the purpose of containment. b Allow 2-3 days for the Oil Stain Remover to dry to a powder. c Sweep and wipe up dried powder and evaluate the stained area for removal. d Repeat process if needed. e Remove any remaining Oil Stain Remover using mineral spirits. For removal of efflorescence, grout haze, salts, mineral deposits and all other calcium-based stains acidic cleaning): Test in an inconspicuous area, as some materials are acid sensitive and may etch when acidic cleaners like StoneTech Professional Restore are applied. Restore may damage stainless steel and other metals. 3 Strip off all wax, acrylic, urethane and all topical finishes. 4 Prepare a solution of Restore mixed with warm or hot water as suggested below: Medium Duty Usage Mix 1 part of Restore to 4 parts of water. Heavy Duty Usage Mix 1 part of Restore to 1 part of water. 5 Liberally apply using a low-pressure chemicalresistant sprayer, sponge or mop. 6 Agitate well using a stiff nylon bristle scrub brush, stiff bristle push broom or a weighted floor machine at 130 lbs.-140 lbs., 175 rpm, fitted with a scrub brush attachment. 7 Rinse well with clean water and mop, sponge or wet vacuum to remove the remaining solution. A hard surface extraction wand and portable or truck mounted extraction machine may be used. Repeat the rinsing and wet vacuum process to insure that all dirt, soil and cleaner residue have been removed. Thoroughly rinse all metal surfaces. SEALING & PROTECTING Natural stone surfaces must be sealed to prevent or minimize staining. Leaving natural stone untreated may greatly hinder the complete removal of stains in the future. The following suggestions are for impregnating the stone and will allow the stone to breathe. Allow new installations to cure for 72 hours prior to applying sealer. Care Instructions For a natural looking protector on interior and exterior surfaces (heavy duty protection, water and oil repellency): 3 Insure that surface is clean and residue-free. 4 StoneTech Professional Heavy Duty Sealer may be applied to damp surfaces one hour after standing water has been removed. 5 Liberally apply an even coat of sealer using a paint pad, low-pressure chemical-resistant sprayer, roller or brush. 6 Allow sealer to penetrate the surface for minutes. During this time, distribute excess over entire area to insure even penetration. Wipe off any remaining sealer prior to drying on the surface. 7 A second coat may be needed for porous, absorbent surfaces and should be applied minutes after initial application as directed in steps A minimum of 15 minutes after final application, wipe entire surface with a clean dry towel to remove any residue and excess sealer, if needed. 9 If sealer was not completely wiped off and a residue appears, wipe entire surface with a towel dampened with sealer. Use a white, 10 A full cure is achieved after hours; foot 11 Expected coverage is sq. ft. per 12 Re-application of Heavy Duty Sealer: A 1-3 year re-application is needed for exterior surfaces. For a natural looking protector on exterior surfaces (heavy duty protection, water repellency only): StoneTech Professional Heavy Duty Exterior Sealer is a water repellent specially designed for exterior projects such as facades, cladding, pool decks, parking areas and driveways. It is very resistant to chemicals (i.e., chlorine) and to the effects of weather (i.e., ultraviolet light/sunlight, driving water/rain). 3 Insure that the surface is clean, dry and residue-free. 4 Liberally apply an even coat of Heavy Duty Exterior Sealer with a paint pad, brush, paint roller or low-pressure solvent-resistant sprayer. 5 Allow sealer to penetrate the surface for 5-15 minutes; denser material may require more time for sealer to penetrate. During this time, distribute excess over entire area to insure StoneTech ProfessioNAL Stone & TILE CARE RESOURCE GUIDE /2007 Edition STONEHELP ( ) MARBLE GRANITE LIMESTONE TRAVERTINE SLATE 33

36 MARBLE GRANITE LIMESTONE TRAVERTINE SLATE even penetration. Wipe off any remaining sealer prior to drying on the surface. 6 A second coat may be needed for porous, absorbent surfaces and should be applied one hour after initial application as directed in steps If sealer was not completely wiped off and a residue appears, wipe entire surface with 8 Do not walk on surface for at least 4-6 hours. Full cure is achieved in hours. 9 Expected coverage is sq. ft. per 10 Re-application of Heavy Duty Exterior Sealer: A 5-10 year re-application is recommended for exterior surfaces. For a color enhancing, impregnating (non-topical) protector on interior and exterior surfaces (heavy duty protection, water and oil repellency): Insure that surface is clean, dry and residue-free. Surface temperature should be between 50 F and 80 F. 3 Ensure area is well-ventilated. Use a respirator if unsure that work area is well-ventilated. A NIOSH approved respirator with a combination HEPA/organic vapor cartridge is recommended. Follow respirator manufacturer s instructions for use. 4 Liberally apply an even coat of StoneTech Professional Enhancer Pro Sealer using a paint pad, roller, brush or pump-up garden sprayer. DO NOT USE A POWER SPRAYER. Ensure that Enhancer Pro is distributed evenly over the entire surface to ensure even penetration. Uneven penetration will result in a blotchy appearance. 5 Allow to penetrate the surface for minutes; denser material may require more time for Enhancer Pro to penetrate. During this time, distribute excess over entire area to insure even penetration. Completely wipe surface with a clean dry terrycloth towel. DO NOT ALLOW ENHANCER PRO TO DRY COMPLETELY ON SURFACE! Failure to remove enhancer from the surface may result in a film or residue that may need to be mechanically removed. 6 A second coat may be needed for porous, absorbent surfaces or if a darker appearance is required and should be applied one hour after initial application as directed in steps If sealer was not completely wiped off and a residue appears, wipe entire surface with a towel dampened with sealer. Use a white, 8 A full cure is achieved after hours; foot 9 Expected coverage is sq. ft. per 10 Re-application of Enhancer Pro : interior or exterior surfaces. WARNING: HARMFUL VAPORS. HARMFUL OR FATAL IF SWALLOWED. COMBUSTIBLE. KEEP OUT OF THE REACH OF CHILDREN. Do not ingest. Avoid contact with eyes and skin. Avoid exposure to vapors. Use in a well-ventilated area. For spray application: Use a pump-up garden sprayer. DO NOT USE A POWER SPRAYER. Use a respirator if unsure that work area is wellventilated. A NIOSH approved respirator with a combination HEPA/organic vapor cartridge is recommended. Follow respirator manufacturer s instructions for use. Do not freeze or store above 100 F/38 C. Do not mix with other chemicals. For a color enhancing, impregnating (non-topical) protector on interior surfaces (economical protection, water and oil repellency): Insure that surface is clean, dry and residue-free. 3 Liberally apply an even coat of StoneTech Professional Enhancer using a paint pad, low-pressure chemical-resistant sprayer, roller or brush. 4 Allow to penetrate the surface for minutes; denser material may require maximum time for enhancer to penetrate. During this time, distribute excess over entire area to insure even penetration. Completely wipe surface dry. DO NOT ALLOW ENHANCER TO DRY COMPLETELY ON SURFACE! 5 A second coat may be needed for porous, absorbent surfaces or if a darker appearance is required and should be applied one hour after initial application as directed in steps A full cure is achieved after hours; foot 7 Expected coverage is sq. ft. per 8 Re-application of Enhancer: For a wet look, high gloss, color enhancing, topical protector on interior and exterior surfaces (maximum protection, water and oil repellency, resistant to acid etches): 1 Thoroughly pre-clean all debris, dirt, oil, grease and general stains from the surface using KlenzAll. Remove waxes, coatings, paint, and previously applied sealers first with a commercially available coating stripper. 2 Allow newly cleaned surface to completely dry prior to applying StoneTech Professional High Gloss Lacquer. 3 Mask off and protect any baseboards or 4 Avoid using in direct sunlight. Apply in air temperatures between 55 F to 80 F and on a cool dry surface. Use only in well ventilated area. 5 While wearing an organic vapor respirator, apply 2-3 even coats with a solvent-resistant natural hair bristle brush, roller or lowpressure sprayer. 6 Allow 1-3 hours between coats or until surface is completely dry to the touch. 7 After final application, do not walk on surface until High Gloss Lacquer is completely cured. High Gloss Lacquer will cure in hours. 8 Clean up equipment with ordinary lacquer thinner, except as restricted by your local air quality management district. 9 Coverage varies depending on the porosity of the surface, method of application and desired thickness of coating. Approximately sq. ft. per 10 Re-application of High Gloss Lacquer: 1-3 years based upon wear. Note: Not recommended for areas with high moisture intrusion from below the surface, showers or counter tops. a well-ventilated area with an approved respirator device. MAINTENANCE CLEANING Highly alkaline, acidic, ammoniated, abrasive cleaners and/or bleach may break down the sealer, adversely affecting repellency and may not be good for the stone. Use a neutral cleaner specially formulated for natural stone. For routine cleaning with protection (not recommended for lacquered surfaces): Revitalizer Cleaner & Protector concentrate mixed with warm or hot water as suggested below: Light Duty Usage 1 part Revitalizer Cleaner & Protector to 4 parts water. Medium Duty Usage/Spray Refill 1 part Revitalizer Cleaner & Protector to 1 part water. (One gallon of concentrate makes up to five gallons of ready-to-use solution.) 3 Apply the Revitalizer Cleaner & Protector solution using a low-pressure chemicalresistant sprayer, mop, sponge or automatic scrubbing machine. 4 No rinsing needed. 5 Or use Revitalizer Cleaner & Protector in a ready-to-use spray bottle or wipes. For routine maintenance cleaning: Stone & Tile Cleaner concentrate mixed with warm or hot water as suggested below: 2 ounces Stone & Tile Cleaner in 1 gallon of water. (Do not mix stronger than 2 ounces to a gallon as a maintenance cleaner. One gallon of concentrate makes 65 gallons of cleaning solution.) 3 Apply the solution using a sponge, mop or automatic scrubbing machine, then wipe or rinse off. 4 Or use Stone & Tile Cleaner in a ready-to-use spray bottle or wipes. 34

37 TECHNICAL DATA SHEET BulletProof MAXIMUM SEALER PRODUCT BENEFITS Advanced microbond protection Maximum protection against all stains Makes cleaning stone easier Natural look Water-based low-solids coating Interior & exterior SURFACES Natural stone such as marble, granite, limestone, slate, travertine, sandstone & terrazzo Best suited for the most porous stone surfaces DIRECTIONS: Always test in a small inconspicuous area with a 24-hour cure time to determine ease of application and desired results. Allow new grout installations to cure for a minimum of 72 hours prior to application. Make sure surface is clean, dry and free of waxes and coatings. 1 Mask off and protect any baseboards or adjacent areas to avoid splashing and overspray onto surfaces not intended to be 2 Sealer may be applied to damp surfaces one hour after standing water has been removed. 3 Liberally apply an even coat using a paint pad, low-pressure chemicalresistant sprayer, roller or brush. 4 Allow sealer to penetrate the surface for minutes. During this time, distribute excess over entire area to insure even penetration. Wipe entire surface thoroughly with clean dry towel. 5 A second coat may be needed for porous, absorbent surfaces and should be applied minutes after initial application as directed in steps A minimum of 15 minutes after final application, wipe entire surface with a clean dry towel to remove any excess sealer. If needed, dampen white nylon pad with sealer to remove residue and dry again thoroughly with clean dry towel. 7 A full cure is achieved after hours; foot traffic may begin in 6-8 hours. Cover with red rosin paper, if foot traffic must resume before the recommended time periods have passed. 8 Clean equipment with water. COVERAGE: 200-1,500 sq. ft. per EXPECTED WEAR: 3-5 years on interior surfaces & 1-3 years on exterior surfaces. HANDLING INSTRUCTIONS: Do not ingest. Avoid contact with eyes and skin. Avoid prolonged exposure to vapors. KEEP OUT OF REACH OF CHILDREN. DO NOT FREEZE OR STORE ABOVE 100 F/38 C. DO NOT MIX WITH CHEMICALS. EMERGENCY FIRST AID PROCEDURES: Ingestion: Do not induce vomiting. Call poison control center. Consult a physician. Eye Contact: Flush thoroughly with water for at least 15 minutes and consult a physician if irritation persists. Skin Contact: Wash skin with mild soap and water. Inhalation: Remove to fresh air. Consult a physician if irritation persists. REGULATORY INFORMATION: Per SCAQMD, Rule 1113 regulation for Low-Solids Coatings, VOC = 24 g/l. PROTECT CLEAN TRANSFORM AVAILABLE SIZES 2 oz. Sample Quart Gallon 5 Gallon 55 Gallon StoneTech ProfessioNAL Stone & TILE CARE RESOURCE GUIDE /2007 Edition STONEHELP ( ) 35

38 TECHNICAL DATA SHEET PROTECT HEAVY DUTY Sealer CLEAN TRANSFORM PRODUCT BENEFITS Advanced microbond protection Heavy duty protection against all stains Makes cleaning stone easier Natural look Water-based low-solids coating Interior & exterior SURFACES Natural stone such as marble, granite, limestone, slate, travertine, sandstone, flagstone & terrazzo DIRECTIONS: Always test in a small inconspicuous area with a 24-hour cure time to determine ease of application and desired results. Allow new grout installations to cure for a minimum of 72 hours prior to application. Make sure surface is clean, dry and free of waxes and coatings. 1 Mask off and protect any baseboards or adjacent areas to avoid splashing and overspray onto surfaces not intended to be 2 Sealer may be applied to damp surfaces one hour after standing water has been removed. 3 Liberally apply an even coat using a paint pad, low-pressure chemicalresistant sprayer, roller or brush. 4 Allow sealer to penetrate the surface for minutes. During this time, distribute excess over entire area to insure even penetration. Wipe entire surface thoroughly with clean dry towel. 5 A second coat may be needed for porous, absorbent surfaces and should be applied minutes after initial application as directed in steps A minimum of 15 minutes after final application, wipe entire surface with a clean dry towel to remove any excess sealer. If needed, dampen white nylon pad with sealer to remove residue and dry again thoroughly with clean dry towel. 7 A full cure is achieved after hours; foot traffic may begin in 6-8 hours. Cover with red rosin paper, if foot traffic must resume before the recommended time periods have passed. 8 Clean equipment with water. COVERAGE: 200-1,000 sq. ft. per EXPECTED WEAR: 3-5 years on interior surfaces & 1-3 years on exterior surfaces. HANDLING INSTRUCTIONS: Do not ingest. Avoid contact with eyes and skin. Avoid prolonged exposure to vapors. KEEP OUT OF REACH OF CHILDREN. DO NOT FREEZE OR STORE ABOVE 100 F/38 C. DO NOT MIX WITH CHEMICALS. EMERGENCY FIRST AID PROCEDURES: Ingestion: Do not induce vomiting. Call poison control center. Consult a physician. Eye Contact: Flush thoroughly with water for at least 15 minutes and consult a physician if irritation persists. Skin Contact: Wash skin with mild soap and water. Inhalation: Remove to fresh air. Consult a physician if irritation persists. REGULATORY INFORMATION: Per SCAQMD, Rule 1113 regulation for Low-Solids Coatings, VOC = 18 g/l. AVAILABLE SIZES 2 oz. Sample Quart Gallon 5 Gallon 55 Gallon 36 StoneTech ProfessioNAL Stone & TILE CARE RESOURCE GUIDE /2007 Edition STONEHELP ( )

39 TECHNICAL DATA SHEET Sealer PRODUCT BENEFITS Advanced microbond protection Standard protection against all stains Makes cleaning stone easier Natural look Water-based low-solids coating Interior & exterior SURFACES Natural stone such as marble, granite, limestone, slate, travertine, sandstone, flagstone & terrazzo DIRECTIONS: Always test in a small inconspicuous area with a 24-hour cure time to determine ease of application and desired results. Allow new grout installations to cure for a minimum of 72 hours prior to application. Make sure surface is clean, dry and free of waxes and coatings. 1 Mask off and protect any baseboards or adjacent areas to avoid splashing and overspray onto surfaces not intended to be 2 Sealer may be applied to damp surfaces one hour after standing water has been removed. 3 Liberally apply an even coat using a paint pad, low-pressure chemicalresistant sprayer, roller or brush. 4 Allow sealer to penetrate the surface for minutes. During this time, distribute excess over entire area to insure even penetration. Wipe entire surface thoroughly with clean dry towel. 5 A second coat may be needed for porous, absorbent surfaces and should be applied minutes after initial application as directed in steps A minimum of 15 minutes after final application, wipe entire surface with a clean dry towel to remove any excess sealer. If needed, dampen white nylon pad with sealer to remove residue and dry again thoroughly with clean dry towel. 7 A full cure is achieved after24-72 hours; foot traffic may begin in 6-8 hours. Cover with red rosin paper, if foot traffic must resume before the recommended time periods have passed. 8 Clean equipment with water. COVERAGE: 200-1,000 sq. ft. per EXPECTED WEAR: 3-5 years on interior surfaces & 1-3 years on exterior surfaces. HANDLING INSTRUCTIONS: Do not ingest. Avoid contact with eyes and skin. Avoid prolonged exposure to vapors. KEEP OUT OF REACH OF CHILDREN. DO NOT FREEZE OR STORE ABOVE 100 F/38 C. DO NOT MIX WITH CHEMICALS. EMERGENCY FIRST AID PROCEDURES: Ingestion: Do not induce vomiting. Call poison control center. Consult a physician. Eye Contact: Flush thoroughly with water for at least 15 minutes and consult a physician if irritation persists. Skin Contact: Wash skin with mild soap and water. Inhalation: Remove to fresh air. Consult a physician if irritation persists. REGULATORY INFORMATION: Per SCAQMD, Rule 1113 regulation for Low-Solids Coatings, VOC = 12 g/l. PROTECT CLEAN TRANSFORM AVAILABLE SIZES 2 oz. Sample Quart Gallon 5 Gallon 55 Gallon StoneTech ProfessioNAL Stone & TILE CARE RESOURCE GUIDE /2007 Edition STONEHELP ( ) 37

40 TECHNICAL DATA SHEET PROTECT HEAVY DUTY Exterior Sealer CLEAN TRANSFORM PRODUCT BENEFITS Repels water Weather resistant Heavy duty protection against water-based stains Minimizes efflorescence Natural look Solvent-based Exterior use SURFACES Natural stone such as limestone, granite, slate, flagstone & sandstone Masonry & concrete DIRECTIONS: Always test in a small inconspicuous area with a 24-hour cure time to determine ease of application and desired results. Allow new grout installations to cure for a minimum of 72 hours prior to application. Make sure surface is clean, thoroughly dry and free of waxes and coatings. Surface temperature should be between 50 F and 80 F. 1 Mask off and protect any baseboards or adjacent areas to avoid splashing and overspray onto surfaces not intended to be 2 Liberally apply an even coat with a paint pad, paintbrush, paint roller or low-pressure solvent-resistant sprayer. 3 Allow to penetrate the surface for 5-15 minutes; denser material may require more time for sealer to penetrate. During this time, distribute excess over entire area to insure even penetration. 4 Thoroughly wipe the entire surface with a clean dry cloth to completely remove all excess sealer from the surface. DO NOT ALLOW SEALER TO DRY ON THE SURFACE. 5 A second coat may be needed for porous, absorbent surfaces and should be applied one hour after initial application as directed in steps If sealer was not completely wiped off and a residue appears, wipe entire surface with a towel dampened with sealer. Use a white nylon pad to loosen residue and follow with a clean, white absorbent towel to remove. 7 Do not walk on surface for at least 4-6 hours. Full cure is achieved in hours. 8 Clean equipment with mineral spirits. COVERAGE: 200-1,000 sq. ft. per EXPECTED WEAR: 5-10 years. HANDLING INSTRUCTIONS: Do not ingest. Avoid contact with eyes and skin. Avoid exposure to vapors. Use in a well-ventilated area or with an approved KEEP OUT OF REACH OF CHILDREN. DO NOT FREEZE OR STORE ABOVE 100 F/38 C. DO NOT MIX WITH CHEMICALS. EMERGENCY FIRST AID PROCEDURES: Ingestion: Do not induce vomiting. Call poison control center. Consult a physician. Eye Contact: Flush thoroughly with water for at least 15 minutes and get medical attention. Skin Contact: Wash skin with mild soap and water. Consult physician if irritation is observed and persists. Launder affected clothing before re-wearing. Inhalation: Remove to fresh air. Consult a physician if irritation, nausea, dizziness or respiratory problems persist. AVAILABLE SIZES 2 oz. Sample Quart Gallon 5 Gallon 55 Gallon 38 StoneTech ProfessioNAL Stone & TILE CARE RESOURCE GUIDE /2007 Edition STONEHELP ( )

41 TECHNICAL DATA SHEET HEAVY DUTY Grout Sealer PRODUCT BENEFITS Keeps grout looking new Makes cleaning easier Mold and mildew resistant sealer Heavy duty protection against all stains Natural look Water-based low-solids coating Interior & exterior SURFACES Grout for ceramic & porcelain tile DIRECTIONS: Always test in a small inconspicuous area with a 24-hour cure time to determine ease of application and desired results. Allow new grout installations to cure for a minimum of 72 hours prior to application. Make sure surface is clean, thoroughly dry and free of waxes and coatings. 1 Mask off and protect any baseboards or adjacent areas to avoid splashing and overspray onto surfaces not intended to be 2 Liberally apply using a paint pad, low-pressure chemical-resistant sprayer, narrow roller or natural hairbrush, focusing on the grout joints. 3 Allow sealer to completely penetrate into the grout, 5-15 minutes. 4 Liberally apply a second coat following steps Wipe up all sealer from the surface of the tile. Use a clean, dry, lint-free, cotton towel. 6 If sealer was not completely wiped off and a residue appears, wipe entire surface with a towel dampened with sealer. Use a white nylon pad to loosen residue and follow with a clean, white absorbent towel to remove. 7 A full cure is achieved after hours; foot traffic may begin in 4 hours. Cover with red rosin paper, if foot traffic must resume before the recommended time periods have passed. 8 Clean equipment with water. COVERAGE: 600-1,000 sq. ft. per EXPECTED WEAR: 3-5 years on interior surfaces & 1-3 years on exterior surfaces. HANDLING INSTRUCTIONS: Do not ingest. Avoid contact with eyes and skin. Avoid prolonged exposure to vapors. KEEP OUT OF REACH OF CHILDREN. DO NOT FREEZE OR STORE ABOVE 100 F/38 C. DO NOT MIX WITH CHEMICALS. EMERGENCY FIRST AID PROCEDURES: Ingestion: Do not induce vomiting. Call poison control center. Consult a physician. Eye Contact: Flush thoroughly with water for at least 15 minutes and get medical attention. Skin Contact: Wash skin with mild soap and water. Consult physician if irritation is observed and persists. Launder affected clothing before re-wearing. Inhalation: Remove to fresh air. Consult a physician if irritation persists. REGULATORY INFORMATION: Per SCAQMD, Rule 1113 regulation for Low-Solids Coatings, VOC = 10 g/l. PROTECT CLEAN TRANSFORM AVAILABLE SIZES 2 oz. Sample Pint 24 oz. Spray Quart Gallon 5 Gallon 55 Gallon StoneTech ProfessioNAL Stone & TILE CARE RESOURCE GUIDE /2007 Edition STONEHELP ( ) 39

42 TECHNICAL DATA SHEET PROTECT ORIGINAL Impregnator Pro SEALER CLEAN TRANSFORM PRODUCT BENEFITS Heavy duty protection against all stains Original fluorochemical technology Natural look Solvent-based Interior & exterior SURFACES Natural stone such as marble, granite, limestone, slate, travertine, sandstone & terrazzo DIRECTIONS: Always test in a small inconspicuous area with 24-hour cure time to determine ease of application and desired results. Allow new grout installations to cure for a minimum of 72 hours prior to applying sealer. Make sure surface is clean, dry and free of waxes and coatings. Surface temperature should be between 50 F and 80 F. 1 Mask off baseboards and adjacent areas to avoid overspray onto surfaces not intended to be 2 Liberally apply an even coat using a paint pad, roller, brush or lowpressure solvent-resistant sprayer. 3 Allow sealer to penetrate surface for minutes; denser material may require more time for sealer to penetrate. During this time, distribute excess over entire area to insure even penetration. 4 Thoroughly wipe entire surface with dry cloth to remove excess Impregnator Pro from surface. DO NOT ALLOW IMPREGNATOR PRO TO DRY ON SURFACE. 5 A second coat may be needed for more porous surfaces and should be applied one hour after initial application, as directed in steps If sealer was not completely wiped off and a residue appears, wipe entire surface with a towel dampened with sealer. Use a white nylon pad to loosen residue and follow with white 7 Full cure is achieved after hours; foot traffic may begin in 6-8 hours. Cover with red rosin paper, if foot traffic must resume before the recommended time periods have passed. 8 Clean equipment with mineral spirits. COVERAGE: 200-1,500 sq. ft. per EXPECTED WEAR: 3-5 years on interior surfaces & 1-3 years on exterior surfaces. HANDLING INSTRUCTIONS: Do not ingest. Avoid contact with eyes and skin. Avoid exposure to vapors. Use in a well ventilated area with an approved Do not use a high-pressure sprayer. KEEP OUT OF REACH OF CHILDREN. DO NOT FREEZE OR STORE ABOVE 100 F/38 C. DO NOT MIX WITH CHEMICALS. EMERGENCY FIRST AID PROCEDURES: Ingestion: Do not induce vomiting. Call poison control center. Consult a physician. Eye Contact: Flush thoroughly with water for at least 15 minutes and get medical attention. Skin Contact: Wash skin with mild soap and water. Consult physician if irritation or burning is observed and persists. Launder affected clothing before re-wearing. Inhalation: Remove to fresh air. Consult a physician if irritation, nausea, dizziness or respiratory problems persist. AVAILABLE SIZES 2 oz. Sample Pint Quart Gallon 5 Gallon 55 Gallon 40 StoneTech ProfessioNAL Stone & TILE CARE RESOURCE GUIDE /2007 Edition STONEHELP ( )

43 TECHNICAL DATA SHEET Grout Release PRODUCT BENEFITS Makes grout clean-up easier Reduces grout staining Water-based low-solids coating Interior & exterior SURFACES Natural stone such as marble, limestone, travertine, slate, sandstone & tumbled stone Masonry & concrete DIRECTIONS: Always test in a small inconspicuous area to determine ease of application and desired results. Make sure surface is clean, dry and free of loose debris. Not recommended for use on ceramic tile and dense (low absorbency) stone. Surface temperature should be between 50ºF-80ºF. 1 Mask off and protect any baseboards or adjacent areas to avoid splashing and overspray onto surfaces not intended to be 2 Apply an even coat with a paint pad, paintbrush, paint roller or lowpressure sprayer. 3 Allow Grout Release to completely penetrate the surface for 5-15 minutes. 4 Wipe up all remaining sealer from the surface. Do not allow pooling or sealer to dry on the surface. Do not over apply. 5 Allow for a minimum of 4 hours cure time prior to grouting. 6 After grouting, remove excess grout. Do not allow grout to completely dry prior to removal. 7 Clean equipment with water. COVERAGE: 200-1,000 sq. ft. per HANDLING INSTRUCTIONS: Do not ingest. Avoid contact with eyes and skin. Avoid exposure to vapors. Wear protective gloves and eyewear. KEEP OUT OF REACH OF CHILDREN. DO NOT FREEZE OR STORE ABOVE 100 F/38 C. DO NOT MIX WITH CHEMICALS. EMERGENCY FIRST AID PROCEDURES: Ingestion: Do not induce vomiting. Call poison control center. Consult a physician. Eye Contact: Flush thoroughly with water for at least 15 minutes and get immediate medical attention. Skin contact: Wash skin thoroughly with mild soap and water. Consult physician if irritation or burning is observed and persists. Launder affected clothing before re-wearing. Inhalation: Remove to fresh air. Consult a physician if irritation persists. REGULATORY INFORMATION: Per SCAQMD, Rule 1113 regulation for Low-Solids Coatings, VOC = 15 g/l. PROTECT CLEAN TRANSFORM AVAILABLE SIZES Gallon 5 Gallon 55 Gallon StoneTech ProfessioNAL Stone & TILE CARE RESOURCE GUIDE /2007 Edition STONEHELP ( ) 41

44 TECHNICAL DATA SHEET PROTECT Revitalizer CONCENTRATE CLEANER & PROTECTOR CLEAN TRANSFORM PRODUCT BENEFITS Cleans everyday messes Mold & mildew resistant protector Built-in sealer reinforces protection Make surfaces easier to clean Neutral, gentle formula Available in citrus scent and cucumber scent SURFACES Natural stone such as marble, granite, limestone, travertine, slate, sandstone & terrazzo DIRECTIONS: Dilute concentrated cleaner with warm water to the following mixing chart: Use Heavy duty Spray refill Light duty Revitalizer Use as is 1 part 1 part 1 Apply mixed solution with a mop, sponge or sprayer. 2 Agitate with a mop, towel or sponge as needed. 3 Remove using a clean mop, towel or sponge. No need to rinse. 4 Repeat if necessary for heavily soiled areas. 5 Let area dry completely before using to prevent soiling or accidents. Warm Water 1 part 4 parts COVERAGE: 2,000-10,000 sq. ft. per One gallon of concentrate makes up to 5 gallons of ready-to-use solution. HANDLING INSTRUCTIONS: Do not ingest. Avoid contact with eyes and skin. Avoid prolonged exposure to vapors. KEEP OUT OF REACH OF CHILDREN. DO NOT FREEZE OR STORE ABOVE 100 F/38 C. DO NOT MIX WITH CHEMICALS. EMERGENCY FIRST AID PROCEDURES: Ingestion: Do not induce vomiting. Call poison control center. Consult a physician. Eye Contact: Flush thoroughly with water for at least 15 minutes and get medical attention. Skin Contact: Wash skin with mild soap and water. Consult physician if irritation is observed and persists. Launder affected clothing before re-wearing. Inhalation: Remove to fresh air. Consult a physician if irritation persists. AVAILABLE SIZES Sample Wipe (citrus) 2 oz. Spray Sample (ready-to-use, citrus and cucumber) 35 Wipes Canister (citrus) 24 oz. Spray (ready-to-use, citrus and cucumber) Gallon Refill (ready-to-use, citrus) Gallon (concentrate, citrus) 5 Gallon (concentrate, citrus) 55 Gallon (concentrate, citrus) 42 StoneTech ProfessioNAL Stone & TILE CARE RESOURCE GUIDE /2007 Edition STONEHELP ( )

45 TECHNICAL DATA SHEET CONCENTRATE Stone & Tile Cleaner PRODUCT BENEFITS Cleans everyday messes Neutral, gentle formula Great for stone & ceramic tile floors Clean scent DIRECTIONS: Dilute concentrated cleaner with warm water to the following mixing chart: Use Heavy duty Light duty Cleaner 4 oz. 2 oz. 1 Apply mixed solution with a damp mop, sponge or appropriate professional cleaning equipment. 2 Clean entire area, changing mop water often to insure that soil is not redeposited. Wipe or rinse off. 3 Let area dry completely before using to prevent soiling or accidents. Warm Water 1 Gallon 1 Gallon COVERAGE: 15,000-30,000 sq. ft. per One gallon of concentrate makes more than 64 gallons of cleaning solution. HANDLING INSTRUCTIONS: Do not ingest. Avoid contact with eyes and skin. Avoid prolonged exposure to vapors. KEEP OUT OF REACH OF CHILDREN. DO NOT FREEZE OR STORE ABOVE 100 F/38 C. DO NOT MIX WITH CHEMICALS. PROTECT CLEAN TRANSFORM SURFACES Natural stone such as marble, granite, limestone, travertine, slate, sandstone & terrazzo Ceramic tile, porcelain tile & grout EMERGENCY FIRST AID PROCEDURES: Ingestion: Do not induce vomiting. Call poison control center. Consult a physician. Eye Contact: Flush thoroughly with water for at least 15 minutes and consult a physician if irritation persists. Skin Contact: Wash skin with mild soap and water. Inhalation: Remove to fresh air. Consult a physician if irritation persists. AVAILABLE SIZES 2 oz. Sample (concentrate) 2 oz. Spray Sample (ready-to-use) 35 Wipes Canister 24 oz. Spray (ready-to-use) Quart (concentrate) Gallon (concentrate) 5 Gallon (concentrate) 55 Gallon (concentrate) StoneTech ProfessioNAL Stone & TILE CARE RESOURCE GUIDE /2007 Edition STONEHELP ( ) 43

46 TECHNICAL DATA SHEET PROTECT CONCENTRATE KlenzAll CLEAN TRANSFORM PRODUCT BENEFITS Heavy duty cleaner Powers through stubborn grease & soils Safe on stone, will not etch Professional strength, alkaline formula DIRECTIONS: Always test in a small inconspicuous area to determine ease of use and desired results. Make sure all surfaces to be cleaned are swept or vacuumed to remove loose debris. Dilute concentrated cleaner with warm water to the following mixing chart: Use KlenzAll Warm Water Heavy duty Spray refill Light duty 1 part 1 part 1 part 2 parts 4 parts 8 parts Acid neutralizer 1 part 32 parts SURFACES Natural stone such as marble, granite, limestone, travertine, slate, sandstone & terrazzo Ceramic tile, porcelain tile & grout Masonry & concrete 1 Apply mixed solution with a mop, sponge or sprayer. Do not overspray on surfaces not to be cleaned. 2 Agitate with a scrub brush or floor machine as needed. 3 Remove using a sponge, wet/dry vacuum or damp mop. 4 Rinse area well with clean water. 5 Reseal cleaned area. COVERAGE: 2,000-10,000 sq. ft. per HANDLING INSTRUCTIONS: Do not ingest. Avoid contact with eyes and skin. Avoid prolonged exposure to vapors. Use protective eyewear and gloves. KEEP OUT OF REACH OF CHILDREN. DO NOT FREEZE OR STORE ABOVE 100 F/38 C. DO NOT MIX WITH CHEMICALS. EMERGENCY FIRST AID PROCEDURES: Ingestion: Do not induce vomiting. Call poison control center. Consult a physician. Eye Contact: Flush thoroughly with water for at least 15 minutes and get medical attention. Skin Contact: Flush thoroughly with water for 15 minutes. If burns persist, get medical attention. Launder affected clothing before re-wearing. Inhalation: Remove to fresh air. Consult a physician if irritation persists. AVAILABLE SIZES 2 oz. Sample (concentrate) 24 oz. Spray (ready-to-use) Quart (concentrate) Gallon (concentrate) 5 Gallon (concentrate) 44 StoneTech ProfessioNAL Stone & TILE CARE RESOURCE GUIDE /2007 Edition STONEHELP ( )

47 TECHNICAL DATA SHEET CONCENTRATE Restore PRODUCT BENEFITS Heavy duty cleaner Makes tile & grout look new Cleans away hard water deposits, grout haze, efflorescence & soap scum Professional strength, acidic formula DIRECTIONS: Always test in a small inconspicuous area to determine ease of use and desired results. Make sure all surfaces to be cleaned are swept or vacuumed to remove loose debris. Heavy duty mixture may darken some surfaces. This acidbased cleaner will etch most marble, limestone and travertine surfaces. Will etch or corrode most metal surfaces. Dilute concentrated cleaner with warm water to the following mixing chart: Use Heavy duty Spray refill Light duty Restore 1 part 1 part 1 part Warm Water 1 part 4 parts 16 parts PROTECT CLEAN TRANSFORM SURFACES Ceramic tile, porcelain tile & grout Masonry 1 Mask off and protect any metals, baseboards or adjacent areas to avoid splashing, dripping, and overspray onto surfaces not intended to be cleaned. 2 Apply mixed solution with a clean mop, towel, sponge or sprayer. 3 Agitate with a scrub brush or floor machine as needed. 4 Remove using a sponge, wet/dry vacuum or damp mop. 5 Rinse area well with clean water and wipe dry. Thoroughly rinse all metal surfaces with clean water. 6 Clean and rinse equipment with water. 7 Reseal cleaned area. COVERAGE: 2,000-8,000 sq. ft. per HANDLING INSTRUCTIONS: Do not ingest. Avoid contact with eyes and skin. Avoid prolonged exposure to vapors. KEEP OUT OF REACH OF CHILDREN. DO NOT FREEZE OR STORE ABOVE 95 F/35 C. DO NOT MIX WITH CHEMICALS ESPECIALLY BLEACH AS TOXIC FUMES MAY RESULT. EMERGENCY FIRST AID PROCEDURES: Ingestion: Do not induce vomiting. Call poison control center. Consult a physician. Eye Contact: Flush thoroughly with water for at least 15 minutes and get medical attention. Skin Contact: Flush thoroughly with water for 15 minutes. If burns persist, get medical attention. Launder affected clothing before re-wearing. Inhalation: Remove to fresh air. Consult a physician if irritation persists. AVAILABLE SIZES 2 oz. Sample (concentrate) 24 oz. Spray (ready-to-use) Quart (concentrate) Gallon (concentrate) 5 Gallon (concentrate) 55 Gallon (concentrate) StoneTech ProfessioNAL Stone & TILE CARE RESOURCE GUIDE /2007 Edition STONEHELP ( ) 45

48 TECHNICAL DATA SHEET PROTECT Oil Stain Remover CLEAN TRANSFORM PRODUCT BENEFITS Pulls out deep oil stains Leaves no residue Will not discolor stone Easy to use, no messy plastic wrap needed SURFACES Natural stone such as marble, granite, limestone, travertine, slate, sandstone & terrazzo Grout for ceramic & porcelain tile Masonry & concrete DIRECTIONS: Always test in a small inconspicuous area to determine that the desired results will be achieved. Make sure surface is clean, dry and free of waxes and coatings. 1 Using a plastic or wood spatula, stir thoroughly to mix the paste. 2 Apply a 1/4 thick layer of paste to the stain. Insure that the paste extends at least 1-2 beyond the edge of the stain. 3 Do not cover. 4 Allow hours for paste to completely dry to a powder. 5 Remove powder and discard. 6 Allow solvent to completely dry from the stone. 7 If stain is not completely gone after drying, repeat process. 8 Clean up residue and tools with mineral spirits. 9 Reseal cleaned area. COVERAGE: ½-1 sq. ft. of surface at 1/4 thickness. HANDLING INSTRUCTIONS: Do not ingest. Avoid contact with eyes and skin. Avoid exposure to vapors. Use in a well-ventilated area or with an approved KEEP OUT OF REACH OF CHILDREN. DO NOT FREEZE OR STORE ABOVE 100 F/38 C. DO NOT MIX WITH CHEMICALS. EMERGENCY FIRST AID PROCEDURES: Ingestion: Do not induce vomiting. Call poison control center. Consult a physician. Eye Contact: Flush thoroughly with water for at least 15 minutes and get medical attention. Skin Contact: Wash skin with mild soap and water. Consult physician if irritation is observed and persists. Launder affected clothing before re-wearing. Inhalation: Remove to fresh air. Consult a physician if irritation persists. AVAILABLE SIZES 3 oz. Can Pint 46 StoneTech ProfessioNAL Stone & TILE CARE RESOURCE GUIDE /2007 Edition STONEHELP ( )

49 TECHNICAL DATA SHEET TRANSFORM Polish PRODUCT BENEFITS Adds quick, brilliant shine to polished stone No greasy film Easy to use Great for kitchen countertops & bathroom vanities SURFACES Polished natural stone such as marble, granite, limestone & travertine DIRECTIONS: Always test in a small inconspicuous area to determine that the desired results will be achieved. Make sure surface is clean, dry and free of waxes and coatings. Not for use on floors. May create slipping hazard. 1 Spray a light coat over the entire surface. 2 Spread the polish evenly with a clean, white terry cloth towel. 3 Buff off polish. 4 Continue buffing until there is no visible polish left and high shine appears. HANDLING INSTRUCTIONS: Do not ingest. Avoid contact with eyes and skin. Avoid prolonged exposure to vapors. KEEP OUT OF REACH OF CHILDREN. DO NOT FREEZE OR STORE ABOVE 100 F/38 C. DO NOT MIX WITH CHEMICALS. EMERGENCY FIRST AID PROCEDURES: Ingestion: Do not induce vomiting. Call poison control center. Consult a physician. Eye Contact: Flush thoroughly with water for at least 15 minutes and consult a physician if irritation persists. Skin Contact: Wash skin with mild soap and water. Inhalation: Remove to fresh air. Consult a physician if irritation persists. PROTECT CLEAN TRANSFORM AVAILABLE SIZES 2 oz. Spray Sample 24 oz. Spray StoneTech ProfessioNAL Stone & TILE CARE RESOURCE GUIDE /2007 Edition STONEHELP ( ) 47

50 TECHNICAL DATA SHEET PROTECT RICH COLOR Enhancer Pro CLEAN TRANSFORM PRODUCT BENEFITS Richens color Heavy duty protection against all stains Weather resistant Chlorine resistant Solvent-based Interior & exterior SURFACES Natural stone such as marble, limestone, slate, travertine, sandstone, flagstone, tumbled stone, flamed stone & textured stone Masonry & concrete DIRECTIONS: Always test in a small inconspicuous area with a 24-hour cure time to determine ease of application and desired results. Allow new grout installations to cure for a minimum of 72 hours prior to application. Make sure surface is clean, dry, and free of waxes and coatings. Before application, surface should dry for hours. Surface temperature should be between 50 F and 80 F. 1 Mask off and protect any baseboards or adjacent areas to avoid splashing and overspray onto surfaces not intended to be 2 Liberally apply an even coat using a paint pad, roller, brush or lowpressure solvent-resistant sprayer. Do not use a towel or sponge. Distribute Enhancer Pro evenly over entire surface. Uneven penetration will result in blotchy appearance. 3 Allow Enhancer Pro to penetrate surface for minutes. Denser material may require more time to penetrate. 4 Thoroughly wipe surface with dry cloth to remove all excess Enhancer Pro. DO NOT ALLOW ENHANCER PRO TO DRY ON SURFACE. Failure to remove Enhancer Pro from surface may result in residue that may need to be mechanically removed. 5 A second coat may be needed for more absorbent surfaces. If darker appearance is required Enhancer Pro should be applied one hour after initial application, as directed in steps Full cure is achieved after hours; foot traffic may begin in 6-8 hours. 7 Clean equipment with mineral spirits. COVERAGE: 200-1,000 sq. ft. per EXPECTED WEAR: 3-5 years. HANDLING INSTRUCTIONS: Do not ingest. Avoid contact with eyes and skin. Avoid exposure to vapors. Use in a well ventilated area with an approved Do not use a high-pressure sprayer. KEEP OUT OF REACH OF CHILDREN. DO NOT FREEZE OR STORE ABOVE 100 F/38 C. DO NOT MIX WITH CHEMICALS. EMERGENCY FIRST AID PROCEDURES: Ingestion: Do not induce vomiting. Call poison control center. Consult a physician. Eye Contact: Flush thoroughly with water for at least 15 minutes and get medical attention. Skin Contact: Wash skin with mild soap and water. Consult physician if irritation is observed and persists. Launder affected clothing before re-wearing. Inhalation: Remove to fresh air. Consult a physician if irritation, nausea, dizziness or respiratory problems persist. AVAILABLE SIZES 2 oz. Sample Pint Quart Gallon 5 Gallon 55 Gallon 48 StoneTech ProfessioNAL Stone & TILE CARE RESOURCE GUIDE /2007 Edition STONEHELP ( )

51 TECHNICAL DATA SHEET TRANSFORM RICH COLOR Enhancer PRODUCT BENEFITS Richens color Standard protection against all stains Water-based Interior use only SURFACES Natural stone such as marble, limestone, slate, travertine, tumbled stone, flamed stone & textured stone Masonry & concrete DIRECTIONS: Always test in a small inconspicuous area with a 24-hour cure time to determine ease of application and desired results. Allow new grout installations to cure for a minimum of 72 hours prior to application. Make sure surface is clean, thoroughly dry and free of waxes and coatings. Not recommended for exterior surfaces. 1 Mask off and protect any baseboards or adjacent areas to avoid splashing and overspray onto surfaces not intended to be 2 Liberally apply an even coat using a paint pad, low-pressure chemicalresistant sprayer, roller or brush. 3 Allow to penetrate the surface for minutes; denser material may require maximum time for Enhancer to penetrate. During this time, distribute excess over entire area to insure even penetration. Completely wipe surface dry with clean, dry terrycloth towel. DO NOT ALLOW ENHANCER TO DRY COMPLETELY ON SURFACE. 4 A second coat may be needed for porous, absorbent surfaces or if a darker appearance is required and should be applied one hour after initial application as directed in steps A full cure is achieved after hours; foot traffic may begin in 6-8 hours. Cover with red rosin paper, if foot traffic must resume before the recommended time periods have passed. 6 Clean equipment with water. COVERAGE: 200-1,000 sq. ft. per EXPECTED WEAR: 3-5 years. HANDLING INSTRUCTIONS: Do not ingest. Avoid contact with eyes and skin. Avoid prolonged exposure to vapors. Wear protective gloves and eyewear. KEEP OUT OF REACH OF CHILDREN. DO NOT FREEZE OR STORE ABOVE 100 F/38 C. DO NOT MIX WITH CHEMICALS. EMERGENCY FIRST AID PROCEDURES: Ingestion: Do not induce vomiting. Call poison control center. Consult a physician. Eye Contact: Flush thoroughly with water for at least 15 minutes and get medical attention. Skin Contact: Wash skin with mild soap and water. Consult physician if irritation is observed and persists. Launder affected clothing before re-wearing. Inhalation: Remove to fresh air. Consult a physician if irritation persists. PROTECT CLEAN TRANSFORM AVAILABLE SIZES 2 oz. Sample Quart Gallon 5 Gallon 55 Gallon StoneTech ProfessioNAL Stone & TILE CARE RESOURCE GUIDE /2007 Edition STONEHELP ( ) 49

52 TECHNICAL DATA SHEET PROTECT HIGH GLOSS Lacquer CLEAN TRANSFORM PRODUCT BENEFITS Topical high gloss look & richens color Maximum protection against all stains Weather resistant Solvent-based Interior & exterior SURFACES Natural stone Masonry & concrete (outdoor patios, walkways, driveways, garage floors, concrete slabs, sidewalks, retaining walls & BBQ areas) AVAILABLE SIZES 4 oz. Sample Gallon 5 Gallon DIRECTIONS: Always test in an inconspicuous area to determine that the desired results will be achieved. If applying over a previously sealed or coated surface, test to insure good adhesion. Surface must be thoroughly clean and dry before application. Lacquer should not be applied to a wet or moist surface. Not recommended for areas with high moisture intrusion from below the surface. Application to a dirty or dusty surface will affect adhesion. Not intended for use on dense, glazed, polished, or non-absorbing surfaces (ceramic tile, porcelain tile), wood floors & decks. 1 Use KlenzAll or Restore as needed to thoroughly clean surface. To remove previously applied lacquers and coatings, use Coating Stripper. 2 Allow newly cleaned surface to completely dry prior to applying Lacquer. 3 Fresh concrete requires a minimum of 28 days to cure before applying Lacquer. 4 Avoid applying in direct sunlight. Apply in air temperatures between 55ºF-80ºF and on a cool, dry surface. Use only in a well-ventilated area. 5 While wearing an organic vapor respirator, liberally apply 2-4 even coats with a solvent-resistant natural bristle brush, roller or low-pressure sprayer. Failure to apply a sufficient amount of Lacquer to the surface may result in chipping or degradation of the coating. More coats may be applied if desired. Formulated to be used without thinning. 6 Allow 1-3 hours between coats or until surface is dry to the touch. 7 After application, do not walk on surface until Lacquer is completely cured. Lacquer will cure in hours. 8 Clean up equipment with ordinary lacquer thinner, except as restricted by your local air quality management district. 9 Lacquer can be reapplied over existing coat of Lacquer to touch up scratches, bubbles, footprints, etc. No stripping is required. Finished surfaces may be slippery when wet. COVERAGE: sq. ft. per HANDLING INSTRUCTIONS: Do not ingest. Avoid contact with eyes and skin. Avoid exposure to vapors. Open all windows and doors to prevent vapor build-up. Wear protective gloves, eyewear and organic vapor respirator when applying. Keep away from heat, sparks and open flames. Properly discard used rags, brushes or rollers in a sealed, water-filled metal container, after use. KEEP OUT OF REACH OF CHILDREN. DO NOT FREEZE OR STORE ABOVE 100 F/38 C. DO NOT MIX WITH CHEMICALS. EMERGENCY FIRST AID PROCEDURES: Ingestion: Do not induce vomiting. Call poison control center. Consult a physician. Eye Contact: Flush thoroughly with water for at least 15 minutes and get immediate medical attention. Skin Contact: Wash skin thoroughly with mild soap and water. Consult physician if irritation or burning is observed and persists. Launder affected clothing before re-wearing. Inhalation: Remove to fresh air. Consult a physician if irritation, dizziness or respiratory problems persist. REGULATORY INFORMATION: VOC = 275 g/l 50 StoneTech ProfessioNAL Stone & TILE CARE RESOURCE GUIDE /2007 Edition STONEHELP ( )

Stone & Tile Care Resource Guide

Stone & Tile Care Resource Guide 2005/2006 EDITION 2005/2006 EDITION Stone & Tile Care Resource Guide KEEPING STONE & TILE BEAUTIFUL Table of Contents CARE INSTRUCTIONS BY SURFACE TYPE Marble Granite Limestone Travertine 1 3 5 7 9 11

More information

DuPont StoneTech Professional Stone And Tile Care Resource Guide 2008/2009 EDITION

DuPont StoneTech Professional Stone And Tile Care Resource Guide 2008/2009 EDITION Stone And Tile Care Resource Guide 2008/2009 EDITION Table of Contents Click on a product name below to go directly to that page. Care Instructions by Surface Type Marble Granite Limestone Travertine Slate

More information

Clean-it Brick and Masonry

Clean-it Brick and Masonry Brick and Masonry Brick and Masonry is an inhibited acid-based cleaner for the removal of cementand mortar residues. For light cleaning (cleaning of unhardened cement haze), dilute 1 part Brick and Masonry

More information

Dependent on the porosity of the surface typically sq.mt. per litre.

Dependent on the porosity of the surface typically sq.mt. per litre. S.Q.T STAIN BAN Anti Stain Impregnator For Natural Stone, Porcelain and Ceramic Surfaces Available in 5l, 1l and 500ml STAIN BAN is an anti stain, oil and water repellent penetrating impregnator for the

More information

Grout Haze Remover DETERDEK PORCELAIN, CERAMICS, TERRACOTTA, ACID RESISTANT STONE

Grout Haze Remover DETERDEK PORCELAIN, CERAMICS, TERRACOTTA, ACID RESISTANT STONE Grout Haze Remover DETERDEK PORCELAIN, CERAMICS, TERRACOTTA, ACID RESISTANT STONE Removes cement grout haze and construction dirt. Eliminates efflorescence from grout, terracotta and brick. Removes lime

More information

Care & Maintenance guide

Care & Maintenance guide Care & Maintenance guide The natural stone you have in your home, office, or commercial building is an investment that will give you many years of beautiful service. Simple care and maintenance will help

More information

Stone Care Guidelines

Stone Care Guidelines Each stone, created by the earth itself, upholds its own unique properties and geological composition. Because of this, some stones require greater maintenance than others. By following these simple guidelines,

More information

COTTOSOLV Concentrated alkaline-based degreaser. to remove wax, resin, polymers and previous treatments.

COTTOSOLV Concentrated alkaline-based degreaser. to remove wax, resin, polymers and previous treatments. COTTOSOLV Concentrated alkaline-based degreaser. COTTOSOLV is a highly concentrated alkaline-based degreaser that is highly recommended for stripping wax, resin, polymers and other treatments, even when

More information

TECHNICAL SPECIFICATIONS ON NATURAL STONE PRODUCTS MENU

TECHNICAL SPECIFICATIONS ON NATURAL STONE PRODUCTS MENU ON NATURAL STONE PRODUCTS MENU TEC1 TEC2A TEC2B TEC3 TEC4 TEC5 TEC6 TEC7 TEC8 TEC9 TEC10 TEC11 TEC12 TEC13 TEC14 TEC15 TEC16 TEC17 S.Q.T. STAIN BAN S.Q.T. POULTICE POWDER S.Q.T. POULTICE POWDER CONTINUED

More information

HOW TO CLEAN AND CARE FOR MARBLE

HOW TO CLEAN AND CARE FOR MARBLE HOW TO CLEAN AND CARE FOR MARBLE CONTENTS 3 GET TO KNOW YOUR STONE 4 STAIN AND SCRATCH PREVENTION 6 SEALING 7 STAIN INDENTIFICATION AND REMOVAL 9 FINAL THOUGHTS MARBLE CARE GUIDE 2 GET TO KNOW YOUR STONE

More information

PROFESSIONAL SPOTTING KIT

PROFESSIONAL SPOTTING KIT CLEANING SOLUTIONS Table of Contents Fire Restoration Products... 2 Emulsifier/Prespray Products... 3 Interim Cleaning Products... 2-3 Spotting Products... 4 Upholstery Care... 5 Deodorizers... 5 Green

More information

General Finishes

General Finishes General Finishes 2017 Flippin Furniture Expo Classic Oil Finishes: Everything You Ever Wanted to Know Presenter: Rob Szwedo, General Finishes Preparing Raw Wood Sand with progressively finer grits: #100,

More information

Granite warranty. Warranty. Care and maintenance

Granite warranty. Warranty. Care and maintenance Warranty Granite warranty Due to the nature of natural stone we do not warranty stone from discolorations or variations in the stone. Each piece will be inconsistent to the next, although each piece in

More information

Care and Maintenance Guide

Care and Maintenance Guide 1 Care and Maintenance Guide Cal Flame Barbecue Islands, Fireplaces, and Fire Pits This brief guide describes how to clean, protect, and repair your Cal Flame product. It discusses the following topics:

More information

FIRE RESTORATION PRODUCTS. Eliminate A & B Bone Spatula Terry Towel Spotting Brush Spotting Guide Soft Carrying Case

FIRE RESTORATION PRODUCTS. Eliminate A & B Bone Spatula Terry Towel Spotting Brush Spotting Guide Soft Carrying Case CLEANING SOLUTIONS Table of Contents Fire Restoration Products... 2 Restorative Cleaning Products... 3 Interim Cleaning Products... 3 Spotting Products... 4 Upholstery Care... 5 Deodorizers... 5 Green

More information

FIRE RESTORATION PRODUCTS

FIRE RESTORATION PRODUCTS CLEANING SOLUTIONS Table of Contents Fire Restoration Products... 2 Emulsifier/Prespray Products... 3 Interim Cleaning Products... 2-3 Spotting Products... 4 Upholstery Care... 5 Deodorizers... 5 Green

More information

Caring For your Stone

Caring For your Stone Caring For your Stone Care and Precautions Use coasters under all glasses, particularly those containing alcohol or citrus juices. Many common foods and drinks contain acids that will etch or dull the

More information

Discover The Insider Secrets To Keeping Your Hard Surface Areas Clean Without Breaking Your BACK!

Discover The Insider Secrets To Keeping Your Hard Surface Areas Clean Without Breaking Your BACK! Discover The Insider Secrets To Keeping Your Hard Surface Areas Clean Without Breaking Your BACK! SPECIAL REPORT: The Consumer s Inside Guide To Hard Surface Maintenance Dear Homeowner, If you have ANY

More information

Please Read Before Applying General Directions: Note: You may want to print these for future use!

Please Read Before Applying General Directions: Note: You may want to print these for future use! Please Read Before Applying General Directions: Note: You may want to print these for future use! Page One: GENERAL DIRECTIONS Page Two: SPECIAL DIRECTIONS FOR CARPET AND UPHOLSTERY Page Three: SPECIAL

More information

Galleria area. North. West Richmond Ave. Houston, TX P. (713) F. (832) E.

Galleria area. North. West Richmond Ave. Houston, TX P. (713) F. (832) E. C a r e & M a i n t e n a n c e Galleria area 5807 Richmond Ave. Houston, TX 77057 P. (713) 977-4455 F. (832) 834-5480 E. richmond@patio1.com North 3105 Cypress Creek Pkwy Houston TX, 77068 P. (281) 893-9700

More information

Application Guide. Manual Applicators 16 Floor Coating Foam Pad, 18 Paint Tray, NylFoam Stain Pad, Foam Brush, Wiping Rags, Sponges.

Application Guide. Manual Applicators 16 Floor Coating Foam Pad, 18 Paint Tray, NylFoam Stain Pad, Foam Brush, Wiping Rags, Sponges. Application Guide Optional Tools & Supplies Professional Mechanical Equipment High Volume Low Pressure (HVLP) Sprayer, Airless Paint Sprayer w/#11 Tip, Wood Sander, Floor Buffer, Pressure Washer, Commercial

More information

CARE & MAINTENANCE. Natural Stone Care & Maintenance. Get to Know Your Stone: Stone Colors and Appearance:

CARE & MAINTENANCE. Natural Stone Care & Maintenance. Get to Know Your Stone: Stone Colors and Appearance: Get to Know Your Stone: The first step in proper stone care and maintenance is to understand your stone s geological classification and composition. This information will help you to identify what cleaning

More information

MAR GEL PLUS Product to remove rust stains from marble, limestone, travertine and acid-sensitive materials.

MAR GEL PLUS Product to remove rust stains from marble, limestone, travertine and acid-sensitive materials. MAR GEL PLUS Product to remove rust stains from marble, limestone, MAR GEL PLUS is a unique, innovative stain remover specifically formulated to remove rust marks and stains from acid-sensitive materials

More information

sparkle. Natural clinging action saves on the amount of product used. Non-toxic and biodegradable.

sparkle. Natural clinging action saves on the amount of product used. Non-toxic and biodegradable. Laundry Detergent & Softener A naturally derived laundry detergent and pre-spotter made primarily from replenish able natural resources. Cleans, softens, brightens, whitens, deodorizes and removes stains.

More information

PORCELAIN TILES simply clean

PORCELAIN TILES simply clean PORCELAIN TILES PORCELAIN TILES simply clean infos and tips for maintaining floors PORCELAIN TILES cleaning, protecting, maintaining LITHOFIN products have been used with a high degree of success for over

More information

Veterinary Care. Method Bulletin Microcide TB 256 Century Q 64 Millennium Q

Veterinary Care. Method Bulletin Microcide TB 256 Century Q 64 Millennium Q Veterinary Care Method Bulletin 1414 Maintenance and chemicals for cleaning, sanitizing and deodorizing animal care facilities. Microcide TB 256 Century Q 64 Millennium Q 2015 Multi-Clean All rights reserved

More information

How to Keep Your Natural Stone Surface Looking its Best evstone.net

How to Keep Your Natural Stone Surface Looking its Best evstone.net CARE AND MAINTENANCE OF NATURAL LIMESTONE How to Keep Your Natural Stone Surface Looking its Best evstone.net CARE AND MAINTENANCE OF NATURAL LIMESTONE How to Keep Your Natural Stone Surface Looking its

More information

UDATED JANUARY 2016 SPIRALS TEAK FURNITURE PRODUCT CARE WE STRONGLY RECOMMEND USE OF HIGH QUALITY FURNITURE COVERS

UDATED JANUARY 2016 SPIRALS TEAK FURNITURE PRODUCT CARE WE STRONGLY RECOMMEND USE OF HIGH QUALITY FURNITURE COVERS SPIRALS TEAK UDATED JANUARY 2016 SPIRALS TEAK FURNITURE PRODUCT CARE WE STRONGLY RECOMMEND USE OF HIGH QUALITY FURNITURE COVERS The Seasonal Living Spirals Teak Collection is manufactured from Planation

More information

INTERIM CLEANING PRODUCTS

INTERIM CLEANING PRODUCTS CLEANING SOLUTIONS INTERIM CLEANING PRODUCTS Table of Contents Interim Cleaning Products... 1 Fire Restoration Products... 1 Emulsifier/Prespray Products... 2 Spotting Products... 3 Upholstery Care...

More information

Muskogee Public Schools Custodial Procedures for Carpet Care

Muskogee Public Schools Custodial Procedures for Carpet Care CARPET CARE ENTRANCE MATS PURPOSE A. Exterior Mats 1. Remove sand and gravel from shoes prior to entering the building. 2. Minimize the amount of abrading material that will scratch and damage interior

More information

CARE AND MAINTENANCE

CARE AND MAINTENANCE CARE AND MAINTENANCE CARE AND MAINTENANCE 02 CARE AND MAINTENANCE Quartz Surfaces are high-quality, solid, non-porous products that resist scratches, heat, and stains. However, VICOSTONE Quartz Surfaces

More information

Durability Thanks to the unique technology, Viatera withstands most everyday stains, and is scratch and crack resistant.

Durability Thanks to the unique technology, Viatera withstands most everyday stains, and is scratch and crack resistant. Description Viatera Quartz Surfaces In order to create the hardest, most impervious natural countertop material, we combine 93% natural quartz with technologically advanced polymers. The result is Viatera,

More information

CARE AND MAINTENANCE

CARE AND MAINTENANCE CARE AND MAINTENANCE CARE AND MAINTENANCE Vicostone Quartz surfaces are a high quality, solid, non-porous product that is resistant to scratches, heat, and stains. However, Vicostone Quartz surfaces are

More information

FILASYSTEM. The complete catalogue of Fila treatments. TREATMENT CYCLES TREATMENT WHAT TO DO IF STAGES. filasolutions.

FILASYSTEM. The complete catalogue of Fila treatments. TREATMENT CYCLES TREATMENT WHAT TO DO IF STAGES.   filasolutions. FILASYSTEM The complete catalogue of Fila treatments. TREATMENT CYCLES TREATMENT STAGES WHAT TO DO IF Fila has always cared for all your s in stone, porcelain, terracotta and wood, at every stage of treatment:

More information

EX-408 PRIMERS TECHNICAL DATA SHEET PRODUCT DESCRIPTION PRODUCTS SUBSTRATES & PREPARATION

EX-408 PRIMERS TECHNICAL DATA SHEET PRODUCT DESCRIPTION PRODUCTS SUBSTRATES & PREPARATION TECHNICAL DATA SHEET EX-408 PRIMERS PRODUCT DESCRIPTION Commercial Performance Coatings EX-408 Primer is a zinc phosphate containing, polyamide cured epoxy primer, that provides a tough abrasion resistant

More information

Care and Maintenance of Countertops, Bartops, Vanities and other Horizontal Surfaces

Care and Maintenance of Countertops, Bartops, Vanities and other Horizontal Surfaces Care and Maintenance of Countertops, Bartops, Vanities and other Horizontal Surfaces Sensitile Terrazzo, Terrazzo Lumina, and PIXA materials are carefully crafted from a fine concrete mix using state-of-the-art

More information

GUIDE WALLS AND DOORS GENERAL CARE & CLEANING OF SOLUTIONS

GUIDE WALLS AND DOORS GENERAL CARE & CLEANING OF SOLUTIONS GUIDE WALLS AND DOORS GENERAL CARE & CLEANING OF SOLUTIONS Care & Cleaning DIRTT Products_v1-6 - 10May2017 1. CARE AND CLEANING OF EXTRUSIONS Introduction DIRTT s high quality powder coated, veneer wrapped

More information

YOU MAY SAFELY USE: Formula 409R Dow Tub and Tile CleanerR Mr. CleanR

YOU MAY SAFELY USE: Formula 409R Dow Tub and Tile CleanerR Mr. CleanR CARE AND MAINTENANCE GUIDE CARE AND MAINTENANCE GUIDE Thermalfused and High Pressure Laminate Surfaces Vinyl Upholstery Fabrics Cushion Floor Mats Hydraulic Bases Dryers CARE AND CLEANING OF HIGH PRESSURE

More information

TECHNICAL DATA SHEET. PRODUCT DESCRIPTION EX-428 A zinc phosphate polyamide cured epoxy primer. SUBSTRATES & PREPARATION. SUBSTRATE Structural steel

TECHNICAL DATA SHEET. PRODUCT DESCRIPTION EX-428 A zinc phosphate polyamide cured epoxy primer. SUBSTRATES & PREPARATION. SUBSTRATE Structural steel TECHNICAL DATA SHEET PRODUCT DESCRIPTION EX-428 A zinc phosphate polyamide cured epoxy primer. SUBSTRATES & PREPARATION SUBSTRATE Structural steel New steel sheet Aluminium PREPARATION Abrasive blast clean

More information

UPHOLSTERY CLEANING - COMMON QUESTIONS & ANSWERS

UPHOLSTERY CLEANING - COMMON QUESTIONS & ANSWERS UPHOLSTERY CLEANING - COMMON QUESTIONS & ANSWERS COLOUR CHANGE I ve cleaned a sofa in the usual way and now there are pink patches in various places. What can I do? The dyes in the fabric have reacted

More information

Surface Materials Cleaning & Maintenance

Surface Materials Cleaning & Maintenance Surface Materials Cleaning & Maintenance With regular care and maintenance, your Trendway product will continue to provide years of superior performance and satisfaction. Please follow the finish cleaning

More information

FLOOR CARE - CHEMICALS

FLOOR CARE - CHEMICALS FLOOR CARE - CHEMICALS CARPET SPOTTER GENERAL PURPOSE All purpose water-based spotter Low residue formula will not resoil your carpet Gets out tough stains, even the old ones TANNIN CARPET STAIN REMOVER

More information

TECHNICAL DATA SHEET TECHNICAL DATA SHEET

TECHNICAL DATA SHEET TECHNICAL DATA SHEET TECHNICAL DATA SHEET TECHNICAL DATA SHEET PRODUCT DESCRIPTION EX-408 Primer is a zinc phosphate containing, polyamide cured epoxy primer, that provides a tough abrasion resistant film with good build characteristics.

More information

CORIAN SOLID SURFACE CARE AND MAINTENANCE FOR FACILITY MANAGERS

CORIAN SOLID SURFACE CARE AND MAINTENANCE FOR FACILITY MANAGERS CORIAN SOLID SURFACE CARE AND MAINTENANCE FOR FACILITY MANAGERS INTRODUCTION Corian Solid Surface meets the demanding needs of today s commercial surfacing applications. As a solid, nonporous surface,

More information

Project Application Guide Waterlox True Tone Color-Infused Tung Oil Stain & Waterlox Buff-in Tung Oil Finish

Project Application Guide Waterlox True Tone Color-Infused Tung Oil Stain & Waterlox Buff-in Tung Oil Finish Project Application Guide Waterlox True Tone Color-Infused Tung Oil Stain & Waterlox Buff-in Tung Oil Finish As with any finish, special care and attention should be used when applying it. Waterlox delivers

More information

DETAILING SOLUTIONS FOR PAINT & BODY SHOPS

DETAILING SOLUTIONS FOR PAINT & BODY SHOPS DETAILING SOLUTIONS FOR PAINT & BODY SHOPS STEP 1 After wet sanding, first use CP-1012 with a cutting wool pad @ 1000-1400 rpm to remove sand marks. Buff Out Sanding Marks Product Description CP-1012 Item#

More information

ATOMIC CHEMICALS PRODUCT RANGE

ATOMIC CHEMICALS PRODUCT RANGE ATOMIC CHEMICALS PRODUCT RANGE HIGH PERFORMANCE CLEANING SOLUTIONS WHATEVER THE PROBLEM, WE HAVE THE SOLUTION Tel: (03) 9580 2766 Fax: (03) 9580 4922 FLOOR CARE EZYMOP (Colour Code Orange No.1) A concentrated

More information

THE LITHOFIN PRODUCT RANGE Cleaning. Protecting. Maintaining.

THE LITHOFIN PRODUCT RANGE Cleaning. Protecting. Maintaining. THE LITHOFIN PRODUCT RANGE Cleaning. Protecting. Maintaining. Products for ceramic and porcelain tiles, natural and engineered stone, concrete, terrazzo, external pavers and other surfaces. FAMILY COMPANY

More information

Care & Maintenance Guide

Care & Maintenance Guide Care & Maintenance Guide Everyday Cleaning Caesarstone requires very little maintenance to keep the surface looking like new. For everyday, routine cleaning of Caesarstone we recommend wiping the surface

More information

TABLE TOP CARE. Edition information pack

TABLE TOP CARE. Edition information pack TABLE TOP CARE Edition. 001 information pack INSTRUCTIONS Regular maintenance and care will help to lengthen the lifespan of your table tops and ensure they look as good as possible, for as long as possible.

More information

Dulon Polish Application Guide

Dulon Polish Application Guide Dulon Polish Application Guide www.dulon.com.au Dulon Polish Application Guide for Boats This guide is intended to assist in the application of Dulon products and assumes that the users have basic knowledge

More information

Cleaning Instructions

Cleaning Instructions Cleaning Instructions Although Tarimatec no maintenance, if that should be cleaned periodically installation to keep it looking good. It is necessary to clean the space between the slats of organic debris

More information

Care Guide. Residential Care and Maintenance

Care Guide. Residential Care and Maintenance Care Guide Residential Care and Maintenance Caesarstone Delivers Uncompromising Peformance Caesarstone quartz surfaces are hard and nonporous, making them a breeze to clean, so you can always maintain

More information

care and cleaning instructions

care and cleaning instructions care and cleaning instructions maintenance for izzy+ flavors products To preserve the condition and improve the longevity of your products, izzy+ has provided care and cleaning instructions for your convenience.

More information

Masonite. The Beautiful Door. STAINING INSTRUCTIONS FOR MASONITE FIBERGLASS ENTRY SYSTEMS. Staining made easy. 1. Prepare. 2. Stain. 3.

Masonite. The Beautiful Door. STAINING INSTRUCTIONS FOR MASONITE FIBERGLASS ENTRY SYSTEMS. Staining made easy. 1. Prepare. 2. Stain. 3. Masonite. The Beautiful Door. STAINING INSTRUCTIONS FOR MASONITE FIBERGLASS ENTRY SYSTEMS Staining made easy 1. Prepare 2. Stain 3. Top-Coat Fiberglass Door Staining Instructions How to Stain Masonite

More information

A liquid cleansing agent ideal for removing dirt and and all-temperature powder

A liquid cleansing agent ideal for removing dirt and and all-temperature powder LAUNDRY CARE Saver All Purpose Detergent Powder An economical low suds powder detergent recommended for light soiled and medium soiled fabrics. It is versatile enough for hard or soft water, hot or cold.

More information

SKIN CARE AND HAND HYGIENE PRODUCT CATALOGUE PRE-WORK SKIN PROTECTION SKIN CLEANING AND CARE AFTER-WORK SKIN CARE

SKIN CARE AND HAND HYGIENE PRODUCT CATALOGUE PRE-WORK SKIN PROTECTION SKIN CLEANING AND CARE AFTER-WORK SKIN CARE SKIN CARE AND HAND HYGIENE PRODUCT CATALOGUE PRE-WORK SKIN PROTECTION SKIN CLEANING AND CARE AFTER-WORK SKIN CARE SKIN CARE PROGRAMME Americol hand care products: protect, clean and care In today s world

More information

MAINTENANCE GUIDE. Keep your wood floor looking beautiful

MAINTENANCE GUIDE. Keep your wood floor looking beautiful MAINTENANCE GUIDE Keep your wood floor looking beautiful 1 Maintenance products to suit your chosen finish: Oiled floors Lacquered floors Laminate floors Vinyl floors or tiles Waxed floors...to give lasting

More information

Big Sky Product Information Sheet. System 10 Acrylic Enamel Color System

Big Sky Product Information Sheet. System 10 Acrylic Enamel Color System Big Sky Product Information Sheet Technical Support (800) 328-4892 P.I. Sheet #1031 System 10 Acrylic Enamel Color System READ ENTIRE PRODUCT INFORMATION SHEET PRIOR TO USE. IF ANY QUESTIONS ARISE, PLEASE

More information

Care Guide. Care and Maintenance Manual

Care Guide. Care and Maintenance Manual Care Guide Care and Maintenance Manual Caesarstone quartz surfaces are hard and nonporous, making them a breeze to clean, so you can always maintain the Caesarstone shine. In most cases, a little soap

More information

HAND CLEANING & HAND CARE

HAND CLEANING & HAND CARE HAND CLEANING & HAND CARE HAND PROTECTION HAND PROTECT LOTION PRODUCTCODE 871 Pre-work skin protectant Forms a barrier to prevent harmful substances from penetrating the skin. Facilitates rapid cleaning

More information

PRODUCT LIST ONE GRAND - CAR CARE PRODUCTS

PRODUCT LIST ONE GRAND - CAR CARE PRODUCTS ONE GRAND BLITZ CARNAUBA WAX - The ultimate Carnauba paste wax that works equally well on all paint colors and types of paint. Produces a deep, durable, "wet look" shine that protects the paint against

More information

S36. How BodyGard S36 Coating Works. VOC Free Premium Glass Coating for your painted automotive body.

S36. How BodyGard S36 Coating Works. VOC Free Premium Glass Coating for your painted automotive body. BBodyGard S36 Key Benefits : Super hydrophobic and oleophobics Enhance glossiness Smooth Finishing Organic Stains resistant Harsh weather resistant Ultranon-stick properties Chemicals resistant Invisible

More information

Sample Chart. Compare Corian to other materials. Endless design options. (actual colors may differ due to printing process or monitor color)

Sample Chart. Compare Corian to other materials. Endless design options. (actual colors may differ due to printing process or monitor color) Corian is: The surface with extraordinary possibilities Available in over 100 colors and unlimited custom Stain resistant NSF/ANSI Standard 51 Certified for food contact and Class I(A) fire rated Durable:

More information

Adura Care and Maintenance

Adura Care and Maintenance Adura Care and Maintenance You can protect your Mannington Adura Floor by following these easy guidelines. Use doormats outside each entrance to your home to prevent dirt, sand, grit and other substances

More information

RESIN RR + HARDENER BM50H RESIN ABELION A HARDENER ABELION B-BB25 ABELION A ABELION B-BM50H

RESIN RR + HARDENER BM50H RESIN ABELION A HARDENER ABELION B-BB25 ABELION A ABELION B-BM50H RESIN RR + HARDENER BM50H LIQUID EPOXY SYSTEM WITH HIGH VISCOSITY Good transparency Sandwich High viscosity epoxy system without solvent for gluing marble, granite, quartz, ceramic and glass. Good hardness

More information

HAND CLEANER PROMOTION

HAND CLEANER PROMOTION HAND CLEANER PROMOTION 800.868.4326 www.tifco.com PROMOTION GOOD THROUGH 12.31.2018 Buy 1 case of Cherry Fibril-Grit or Fibril-Cleen Hand Cleaner and get the dispenser and Tough Box Portable Shop Towels

More information

DAZZLE NON-BUTYL CLEANER/DEGREASER 420

DAZZLE NON-BUTYL CLEANER/DEGREASER 420 DAZZLE NON-BUTYL CLEANER/DEGREASER 420 Dazzle is the ultimate state of the art product for cleaning effectiveness, safety to personnel, and harmlessness to the surfaces to be cleaned. The particular combination

More information

Smart Cleaning Smar Pr t-cleaning ofessional Cleaning aid

Smart Cleaning Smar Pr t-cleaning ofessional Cleaning aid Smart Cleaning Professional Smart-Cleaning Cleaning aid 02 Toilet & Bathroom Cleaning: Glass-Mirror-Chrome-Acrylic-Porcelain-Marble 03 Always like New: with a small and superior product range NANO-CERAMIC

More information

Feltpen Fadeout For the for the final removal of ink stains and certain spray can shadows on smooth or porous surfaces

Feltpen Fadeout For the for the final removal of ink stains and certain spray can shadows on smooth or porous surfaces Page 1 of 5 PRODUCT DESCRIPTION FELTPEN FADEOUT (FPFO) is designed for the final removal of shadows and traces of inks and dyes and other graffiti markers from all surfaces; porous and non porous. FPFO

More information

Great System. New for Break Through Formula. Extremely Popular FOOD PLANT APPROVED PRODUCTS 20+ AVAILABLE IN ALL CATEGORIES

Great System. New for Break Through Formula. Extremely Popular FOOD PLANT APPROVED PRODUCTS 20+ AVAILABLE IN ALL CATEGORIES www.grimeeater.com New for 2011 Great System Now available with 8 great products Lotion Soap, Cream Soap & Foam Soap Solvent Free & Cherry Solvent Free Hand Cleansers See it all on Page 27 Break Through

More information

PRODUCT LIST ZYMOL - CAR CARE PRODUCTS

PRODUCT LIST ZYMOL - CAR CARE PRODUCTS 11101 Zymol Creame Wax - 8 oz Jar ZYMOL CREAME WAX - 8 OZ JAR - Creame formula is for light colors. A totally abrasive free wax containing nutritive oils, enzymes and 33% Brazilian #1 Carnauba to replenish

More information

SM QUARTZ INSTRUCTIONS FOR CLEANING AND MAINTENANCE OF COUNTERTOPS HONED, BRUSHED, WAVE AND METROPOLIS FINISHES

SM QUARTZ INSTRUCTIONS FOR CLEANING AND MAINTENANCE OF COUNTERTOPS HONED, BRUSHED, WAVE AND METROPOLIS FINISHES SM QUARTZ INSTRUCTIONS FOR CLEANING AND MAINTENANCE OF COUNTERTOPS HONED, BRUSHED, WAVE AND METROPOLIS FINISHES POST-FABRICATION CLEANING Once the slabs have been fabricated, remove any residue with water

More information

carpets dirty? i m your solution

carpets dirty? i m your solution Carpets Dirty? I m Your Solution is a concentrated extraction cleaner formulated to conform with manufacturers recommendations for stain resistant carpet. Low foaming anionic wetting agents are the foundation

More information

ARSENAL. Product description. Design: Alessio Bassan

ARSENAL. Product description. Design: Alessio Bassan Product description Modular bookcase with frame in titanium (GFM11), white (GFM71), black (GFM73) or graphite (GFM69) lacquered steel. Shelves in Canaletto walnut (NC) or burned oak (RB) or white (GF71)

More information

Care & Maintenance. Keep your windows looking and working great.

Care & Maintenance. Keep your windows looking and working great. Care & Maintenance Keep your windows looking and working great. Care and Cleaning of vinyl windows (SINGLE HUNG, DOUBLE HUNG, CASEMENT AND SLIDING WINDOWS) Congratulations on your selection of windows

More information

Chemical. Since The Choice of the Profitable Car Wash. Car Wash Division

Chemical. Since The Choice of the Profitable Car Wash. Car Wash Division Chemical Since 1988 The Choice of the Profitable Car Wash Car Wash Division Our Commitment is to the Professional Car Care Industry. Stinger Chemical is one of the fastest growing companies providing quality

More information

MM FLZ BXTS010 MM FLZ Bp03511 MM FLZ bu03515 MM FLZ CA MM FLZ CA03588 MM FLZ ic03521

MM FLZ BXTS010 MM FLZ Bp03511 MM FLZ bu03515 MM FLZ CA MM FLZ CA03588 MM FLZ ic03521 METAL, PLASTIC & FIBERGLASS POLISH PASTE MM FLZ BXTS010 MM FLZ Bp03511 MM FLZ bu03515 MM FLZ CA03518-6 MM FLZ CA03588 MM FLZ ic03521 2 gr. packet 50 gr. blister tube 150 gr. boxed Tube 906 gr. can 3624

More information

PE2600 2:1 Acrylic Urethane Clear 4.3VOC

PE2600 2:1 Acrylic Urethane Clear 4.3VOC Big Sky Product Information Sheet Technical Support (800) 328-4892 P.I. Sheet #1093 PE2600 2:1 Acrylic Urethane Clear 4.3VOC COMPONENTS SPECIALTY COMPONENTS (OPTIONAL) 1. PE2600 Clear 1. CR22ACC Accelerator

More information

Natural Stone Interiors.com

Natural Stone Interiors.com Taking Care Of Your Natural Stone PRESENTED BY... Natural Stone Interiors.com Your Guide to Natural Stone www.natural-stone-interiors.com GRANITE, MARBLE AND OTHER NATURAL STONE PRODUCTS INFORMATION www.mygranitecare.com

More information

CATEGORY REPORT CARPET/UPHOLSTERY. No-rinse formula removes most common dirt and water based spots. 12 per case

CATEGORY REPORT CARPET/UPHOLSTERY. No-rinse formula removes most common dirt and water based spots. 12 per case 3M AEROSOL CARPET SPOT REMOVER AND UPHOLSTERY CLEANER 12/ MCO-14003 14003 12/ 11.820 0.563 50048011140037 No-rinse formula removes most common dirt and water based spots. 12 per case 3M CARPET PRETREATMENT

More information

Boat Maintenance. If you have an aversion to labor and don't like fixing things, you have no business owning a boat.

Boat Maintenance. If you have an aversion to labor and don't like fixing things, you have no business owning a boat. Page 1 of 5 www.bananawind.us A vessel is deteriorating from the moment it is built. - Willits D. Ansel Boat Maintenance If you have an aversion to labor and don't like fixing things, you have no business

More information

Stone Buff HARD SURFACE RESTORATION AND REFINISHING NATURAL STONE TILE & GROUT WOOD METAL NATURAL STONE. and Tile & Grout. Care and Maintenance of

Stone Buff HARD SURFACE RESTORATION AND REFINISHING NATURAL STONE TILE & GROUT WOOD METAL NATURAL STONE. and Tile & Grout. Care and Maintenance of Care and Maintenance of NATURAL STONE and Tile & Grout PRESENTED BY... Stone Buff HARD SURFACE RESTORATION AND REFINISHING NATURAL STONE TILE & GROUT WOOD METAL A division of Surface Buff, LLC w w w.stonebuff.com

More information

ABOUT US UNIVERSAL SPECIALITY CHEMICALS PVT. LTD (USCPL

ABOUT US UNIVERSAL SPECIALITY CHEMICALS PVT. LTD (USCPL PRODUCT CATALOGUE UNIVERSAL SPECIALITY CHEMICALS PVT. LTD. (USCPL) is a one-of-a-kind specialty chemicals manufacturer and supplier to various speciality chemicals. We at USCPL have used our raw materials

More information

Cleaning. "postinstallation" Non-slip surfaces CLEANING AND MAINTENANCE

Cleaning. postinstallation Non-slip surfaces CLEANING AND MAINTENANCE CLEANING AND MAINTENANCE 1 Cleaning "postinstallation" Post-installation cleaning helps remove residues of joint grouts, cement and lime. This operation is mandatory after installation both for glazed

More information

Product Data 484 Epoxy Primer Undercoat

Product Data 484 Epoxy Primer Undercoat Product Data 484 Epoxy Primer Undercoat PRODUCTS 484 Epoxy Primer Undercoat 484-6997 Pack A 484 Epoxy Primer Hardener 484-9929 Pack B Thinners R202-Normal conditions, R270-Hot conditions Product Description

More information

SUPPLY AND DELIVERY OF CLEANING MATERIAL FOR A PERIOD OF THREE YEARS SPECIFICATION AND PRICE LIST

SUPPLY AND DELIVERY OF CLEANING MATERIAL FOR A PERIOD OF THREE YEARS SPECIFICATION AND PRICE LIST SUPPLY AND DELIVERY OF CLEANING MATERIAL FOR A PERIOD OF THREE YEARS SPECIFICATION AND PRICE LIST Material Material Description Specifications BUn Price No 249 BAG plastic refuse 750X950mm (20 pk) Must

More information

Quickie Commercial Products

Quickie Commercial Products Quickie Commercial Products Over-Sized Sponge Mop and Refill Extremely durable cellulose sponge provides deeper cleaning on hard flooring surfaces. 11 wide (36 sq. ") sponge made especially for the professional

More information

DuPontTM Zodiaq. Quartz Surfaces

DuPontTM Zodiaq. Quartz Surfaces DuPontTM Zodiaq Quartz Surfaces Sparkling beauty, radiant clarity, creative colours, exceptional strength DuPont Zodiaq is a new surfacing material with star quality that s crystal clear. Zodiaq is composed

More information

It Works! Multi Stain Remover Kit with 2 Tubes & 2 Sponges

It Works! Multi Stain Remover Kit with 2 Tubes & 2 Sponges It Works! Multi Stain Remover Kit with 2 Tubes & 2 Sponges USE: It Works for clothing stains, carpets, upholstery, car seats, head liners, all types of over garments, leather, vinyl, aluminum rims, jewelry,

More information

METAL CARE GUIDE STAINLESS STEEL

METAL CARE GUIDE STAINLESS STEEL METAL CARE GUIDE TESKO ENTERPRISES WORKS WITH MANY METALS AND APPRECIATES THAT EACH IS UNIQUE IN ITS APPEARANCE AND PROPERTIES. OUR WORK IS ALWAYS GUARANTEED TO BE OF THE FINEST QUALITY REGARDLESS OF THE

More information

GB

GB GB www.cds.flowey.com rims & wheels p3-6 bodywork p7-12 polish p13-18 finish & protect p19-24 cockpit p25-28 textile & leather p29-32 glass p33-34 air freshner p35-36 www.cds.flowey.com rims wheels p3-6

More information

CARE & MAINTENANCE. Keep your windows looking and working great

CARE & MAINTENANCE. Keep your windows looking and working great CARE & MAINTENANCE Keep your windows looking and working great Care and Cleaning of vinyl windows (SINGLE HUNG, DOUBLE HUNG, CASEMENT AND SLIDING WINDOWS) CARE OF SCREENS Because our screens are made of

More information

Proper vacuuming requires 3 to 5 passes at slow speed over the same area

Proper vacuuming requires 3 to 5 passes at slow speed over the same area CARPET CLEANING & MAINTENANCE GUIDELINES WOOL & VISCOSE & OR SILK --------- ---------- DAILY CLEANING REGULAR VACUUMING Regular vacuuming of the whole carpet should take place even when the carpet does

More information

Cleaning Instructions for Humanscale Seating Products

Cleaning Instructions for Humanscale Seating Products Cleaning Instructions for Humanscale Seating Products HOW TO CLEAN CHAIR ARM PADS & BASES: Please use mild soap (i.e. Ivory Liquid Soap) and water Gently wipe thoroughly with a soft cloth to remove dirt

More information

Healthy Home by Simplicity Cleaning Product Spot Sales Demonstration Guide

Healthy Home by Simplicity Cleaning Product Spot Sales Demonstration Guide Healthy Home by Simplicity Cleaning Product Spot Sales Demonstration Guide The demonstrations you do will have greater influence on your customers than anything you say or do. A demonstration creates the

More information

Product Data EX-408 Epoxy ZP Primer

Product Data EX-408 Epoxy ZP Primer Product Data EX-408 Epoxy ZP Primer PRODUCTS EX-408 Epoxy ZP Primer EX-408 Hardener Thinners EX-408-Pack A 414-9153 Pack B R202-Normal conditions, R270-Hot conditions Product Description A polyamide cured

More information

Maintenance Instructions Flooring Products

Maintenance Instructions Flooring Products MAINTENANCE INSTRUCTIONS GENERAL 1.1 Chilewich Contract flooring is a woven vinyl fabric bonded to commercial grade backing intended for residential and commercial flooring markets. The unique vinyl fibers

More information

Big Sky Product Information Sheet. CRV21 Crystal Clear 2.1 VOC Universal Clearcoat

Big Sky Product Information Sheet. CRV21 Crystal Clear 2.1 VOC Universal Clearcoat Big Sky Product Information Sheet Technical Support (800) 328-4892 P.I. Sheet #1066 CRV21 Crystal Clear 2.1 VOC Universal Clearcoat READ ENTIRE PRODUCT INFORMATION SHEET PRIOR TO USE. IF ANY QUESTIONS

More information

Care instructions. Laminate / melamine. Lacquer matt / gloss / concrete look / stone look. Wood, lacquered. Wood, oiled / waxed

Care instructions. Laminate / melamine. Lacquer matt / gloss / concrete look / stone look. Wood, lacquered. Wood, oiled / waxed Care instructions Laminate / melamine Lacquer matt / gloss / concrete look / stone look Wood, lacquered Wood, oiled / waxed Acrylic finish / organic glass Glass Linoleum Care instructions for furniture

More information