1, Total Depth (All) (ftkb) Original Hole - 20, ,929, Wind Temperature ( F) Road Condition
|
|
- Wilfred Reed
- 5 years ago
- Views:
Transcription
1 NU B-SECTION & FRAC STACK, SET 2 TANKS & FILL W/ 2% KCL AND BIOCIDE. OPEN TOE SLEEVE, PUMP DOWN DART & TEST CSG. 36, :00 07: INACTIVE 07:00 07: PJSM 36, :30 09: CHECK PRESSURE (0 PSI), ND DRY CAP, NU 7" 15M B-SECTION W/ DOUBLE WING ON ONE SIDE & BLANK ON THE OPPOSITE, TEST VOID 10M 15 MIN (GOOD TEST), INSTALL EXTENDED NECK HANGER W/ BPV. 09:30 14: NU 7" 15M MANUAL & 7" 15M HYD VALVE W/ NITE CAP, FILL & TEST VALVES 12,500 PSI 15 MIN, (GOOD TEST), BLEED PRESSURE OFF & ND NITE CAP PULL TBG HANGER W/ BPV, NU 7" 15M FLOW-X W/ DOUBLE 2" & DOUBLE 4" WING VALVES, 7" 15M SWAB VALVE, & 15M GOAT HEAD W/ NITE CAP, TEST 12,500 PSI 15 MIN, (GOOD TEST), SECURE WELL ALL VALVES SI. 14:30 06: WELL SI & SECURE.
2 OPEN TOE SLEEVE, PUMP DOWN DART & TEST CSG 11,700 PSI. WAIT ON DART TO DISSOLVE. PERFORATE STAGE 1 MONDAY , :00 08: INACTIVE 08:00 08: DISCUSS W/ TEAM ABOUT BOUNDARY LINES & PLAN GOING FORWARD. 08:30 09: PJSM 09:00 09: PTST SURFACE LINES & WH 12,500 PSI 56, :45 10: (9:45) OW W/ 0 PSI, PRESSURE UP SLEEVE MAKING PRESSURE 5000, 7500, & 8500 PSI, PUMP SLEEVE 10,494 PSI. 10:00 10: AFTER SLEEVE OPEN PRESSURE FELL 8,450 3 BPM, WALK RATE TO 7 9,400 PSI, PUMPED 130 BBLS 2% KCL W/ BIO, SWAP TO 15% HCL ACID PUMPED 96 BBLS, 10 BBLS 2% KCL W/ BIO, 50 BBLS OF GEL, 25 BBLS 2% KCL W/ BIO & SD, 4,200 SICP. 10:30 13: DROP DART, EQ & OW 4,200 PSI, FINISH PUMPING ACID/ GEL PICKLE, AVG Q 12.9 BPM, AVG P 8,344 PSI. (11:11) AFTER PUMPING CSG CAP 440 BBLS BBLS (590 BBLS) NEVER SEEN DART HIT, SD CLOSED WELL IN & CHECKED FOR DART, DART WAS SETTING ON SWAB VALVE, PUSHED DART BELOW VALVE WITH DRY ROAD & SHUT SWAB VALVE, OW & BEGIN PUMPING CSG CAP (440 BBLS) DART LANDED 467 BBLS. (13:09) PTST CSG 11,700 PSI 15 MIN (GOOD TEST), BLEED PRESSURE TO 4,000 PSI & SWI. 13:30 06: WAIT ON DART TO DISOLVE.
3 STANDBY FOR DART TO DISSOLVE PUMP DOWN CIBP & GUNS, PERF STG 1 6, :00 06: STANDBY FOR DART TO DISSOLVE (FILL PUMP DN TANKS W/ 2% KCL) 62,848.38
4 PUMP DOWN CIBP & GUNS, PERF STG 1, INJECTION TEST. STANDBY FOR FRAC 13, :00 08: INACTIVE 08:00 08: PJSM 08:15 10: MIRU HES WLU. 76, :00 13: STG 1 PLUG & GUN RUN: SIW W/ 3,825 PSI. RU E-LINE ON WELL. PTST 9,000 PSI, EQUALIZE LUBRICATOR AND OPEN WELL W/ 3,850 PSI. RIH W HALLIBURTON (OWEN) 12.5K CIBP AND (4) 2'x3-3/8" GUNS, 5 SPF, 60 DEG. PHASED. GET ON DEPTH W/ SH0RT 13,271'. PUMP DOWN PLUG FROM 13,800' W/ MAX RATE OF AFPM, MAX PRESSURE 8,211 PSI. SET PLUG AT 20,727' PICK UP & 20,675'-77', 20,588'-90', 20,501'-03' & 20,414'-16' (40 TOTAL HOLES). 366 BBL USED FOR PUMP DOWN. POOH. 13:30. SIW. RD WIRELINE. ALL SHOTS FIRED. 13:30 14: BD PERFS W/ 6,200 5 BPM, INCREASE RATE 14 7,750 PSI, PUMPED 100 BBLS, ISIP 6,205 PSI, 5 MIN 5,096 PSI, 10 MIN 4,938 PSI, 15 MIN 4,879 PSI, 4,851 SICP. 14:00 15: RDMO WL & PUMP TRUCKS, EMPTY & RELEASE WORKING TANKS. 15:00 06: INACTIVE
5 STANDBY FOR FRAC DATE STANDBY FOR FRAC DATE 1, :00 06: STANDBY FOR FRAC DATE 77,648.38
6 SPOT ACID TANKS WITH LINER, RU FLOWBACK AND TESTED. SET ANCHORS ON FB IRON. RU FRAC ROW WITH LINER. 14, , :00 08: :00 12: RU ACID TANK CONTAINMENT AND SPOT TANKS, RU FLOW BACK IRON MANIFOLD AND GAS BUSTER. TESTED TO 9,500 PSI. 12:30 14: :00 17: SET ANCHORS. SDFN. 17:00 06: SDFN
7 RU LINER FOR FRAC ROW, SET FRAC TANKS IN LINER. DROP WELL REPORTS UNTIL FRAC DATE. STANDBY FOR FRAC DATE. DROP WELL REPORTS UNTIL FRAC DATE. 13, :00 07: , :00 09: LAY FELT AND PREP FOR FRAC ROW CONTAINMENT. STAGE FRAC TANKS ON SIDE OF LOC. 09:00 13: :00 18: LAYOUT & RU LINER FOR FRAC ROW, SPOT FRAC TANKS. SDFN 18:00 06: SDFN.
8 FINISH SETTING FRAC ROW, PUT UP LAST CONTAINMENT WALL STANDBY FOR FRAC DATE. DROP WELL REPORTS UNTIL FRAC DATE. 5, :00 14: FINISH SETTING FRAC ROW, PUT UP LAST CONTAINMENT WALL 14:00 06: INACTIVE 110,853.38
9 HES CONTINUE TO MIRU FRAC EQUIPMENT AND MAINT AND REPAIRS ON SAME. PRE FILL SAND AND FRAC ROW. SPOT FRAC EQUIPMENT AND RIG IRON. PRESSURE TEST AND BUCKET TEST. RU WL UNIT. ( FRAC DATE) 20, , :00 06: HES CONTINUE TO MIRU FRAC EQUIPMENT AND MAINT AND REPAIRS ON SAME. PRE FILL SAND AND FRAC ROW.
10 SPOT FRAC EQUIPMENT AND RIG IRON. PRIME PUMPS & PRESSURE TEST, BUCKET TEST CHEMICALS. RU WL UNIT. START FRAC OPERATIONS. 18 STAGES 7, , :00 18: FINISH SPOTTING EQUIPMENT, AND RU FRAC IRON. NU WL FLANGE. MIRU WL TRUCK AND CRANE. SPOT CHEMICAL TRAILERS AND RUN LINES. 18:00 20: PRESSURE TESTED FRAC IRON AND STACK TO 12,500 PSI. GOOD TEST. 20:45 05: SDFN. 05:00 06: STARTING EQUIPMENT TO START RT.
11 FRAC STAGE 1, PERF & FRAC STAGE 2, RIH TO PERF STAGE 3, SET PLUG, SHOT GUNS 1 &2, DID NOT SEE ANY INDICATION OF GUN 3 FIRING, ATTEMPT TO FIRE 4TH GUN W/ NO INDICATION OF GUN FIRING, IT APPEARS GUNS 3 & 4 FIRED AT SAME TIME WHEN GUN 2 WAS FIRED. CALLED SUPERVISOR. MU 2 GUNS TO RIH & FINISH STAGE 3 PERFS (CLUSTERS 3 & RT. FINISH STAGE 3 PERF. REPLACE T-BELT. CONTINUE FRAC OPERATIONS 287, , :00 06: JSA MEETING, DISCUSSED ALL RESTRICTED AREAS, EVACUATION ROUTE AND EMERGENCY CONTINGENCIES. 06:30 07: PRIME CHEMICALS AND TOP OFF FRAC ROW WITH PRODUCED WATER 07:15 08: OPEN WELL WITH 3395 PSI, STARTED STAGE. FLUSH WELL AND SD DUE TO BLOWN GASKET ON A PUMP DOWN JOINT. SD DURING 0.2 PPG 100 MESH (2376 LBS PUMPED) 08:15 09: REPLACE GASKET IN PUMP IRON AND PSI TEST. 09:00 11: CONTINUED STAGE TO 0.8 PPG, THEN THE T-BELT STARTED SLIPPING. FLUSH WELL AND ADJUST BELTS. 11:15 12: ADJUST BELTS ON T-BELT. TRIED TO GO DOWN HOLE AGAIN AND BELT WAS STILL SLIPPING, FLUSH AND SI WELL. 12:00 14: WAITED ON MECHANIC ARRIVE AND ADJUST BELTS AGAIN. 14:00 16: (07:15) FRAC STAGE 1 PERFS 20,414' TO 20,677' AS FOLLOWS; TEST PUMP LINES TO 12,500 PSI. OPEN WELL W/ 3,395 PSI. BD ,931 PSI. FRAC W/ 4,000 GAL OF 15% FE ACID. 12,115 BBL OF PERMVIS VFR - 10 WATER, 1,250 BBLS OF PERM VIS W/ MICRO PROP, 10,397 BBLS OF LINEAR GEL, 77,628 LBS 100 COMMON WHITE, 295,332 LBS 40/70, 75,023 LBS 30/50 WHITE, & 52,285 LBS 30/50 OILPLUS SAND FROM 0.5 TO PPG. AIR 87.9 BPM, ATP 10,347 PSI. TOTAL LOAD TO RECOVER = 23,858 BBLS. ISIP 5,939 PSI, (0.85 FG) 5 MINS 5,101 PSI (16:11). NOTE: WE CUT RATE AND ULTIMATELY SD FOR JUST A FEW MINUTES FOR WATER TRANSFER TO REPRIME PUMPS. 16:15 16: NU WL LUBE, PRESSURE TEST TO 9,500 PSI, BLED TO 0 PSI, LD LUBE TO PICK UP GUNS. 16:45 20: STG 2 PLUG & GUN RUN: SIW W/ 4,926 PSI. RU E-LINE ON WELL. EQUALIZE LUBRICATOR AND OPEN WELL W/ 4,466 PSI. RIH W HALLIBURTON 10K CFP AND (4) 2'x3-3/8" GUNS, 5 SPF, 60 DEG. PHASED. GET ON DEPTH W/ SH0RT 13,271'. PUMP DOWN PLUG FROM 14,000' W/ MAX RATE OF AFPM, MAX PRESSURE 8,011 PSI. SET PLUG AT 20,378' PICK UP & 20,336'-38', 20,252'-54', 20,168'-70' & 20,084-86' (40 TOTAL HOLES). 405 BBL USED FOR PUMP DOWN. POOH. 20:45. SIW W/ 4,400 PSI. RD WIRELINE. ALL SHOTS FIRED. DROP BALL. NU FRAC CAP & TURN WELL OVER TO FRAC. 20:45 21: WO WATER TRANSFER, HAD PROBLEMS WITH COMMUNICATION AT WATER SOURCE AND TRANSFER PUMP RPM S. TALKED WITH THE SUPERVISOR HE SAID THE PROBLEMS HAD BEEN CORRECTED. 21:45 01: (21:44) FRAC STAGE 2 PERFS 20,084' TO 20,338' AS FOLLOWS; TEST PUMP LINES TO 12,500 PSI. OPEN WELL W/ 4,243 PSI. BD ,150 PSI. FRAC W/ 4,000 GAL OF 15% FE ACID. 7,683 BBL OF PERMVIS VFR - 10 WATER, 1,250 BBLS OF PERM VIS W/ MICRO PROP, 5,309 BBLS OF LINEAR GEL, 77,572 LBS 100 COMMON WHITE, 295,548 LBS 40/70, 75,257 LBS 30/50 WHITE, & 29,219 LBS 30/50 OILPLUS SAND FROM 0.5 TO PPG. AIR 89 BPM, ATP 10,212 PSI. TOTAL LOAD TO RECOVER = 14,337 BBLS. ISIP 5,866 PSI, (0.84 FG) 5 MINS 5,005 PSI (01:12). NOTE: 96 % OF DESIGNED SAND PLACED. HALLIBURTON HAD THE HYD MOTOR FALL OFF T-BELT WHICH CONTROLLED THE TOP BELT. THIS CAUSED FRAC TO BE 20,000 LBS SHY OF PRIME PLUS GOING DOWNHOLE AND 6,000 LBS LEFT ON THE T-BELT. MECHANIC FINDING PARTS TO MAKE REPAIRS. 01:15 06: STG 3 PLUG & GUN RUN: SIW W/ 5,267 PSI. RU E-LINE ON WELL. EQUALIZE LUBRICATOR AND OPEN WELL W/ 4,800 PSI. RIH W HALLIBURTON 10K CFP AND (4) 2'x3-3/8" GUNS, 5 SPF, 60 DEG. PHASED. GET ON DEPTH W/ SH0RT 13,271'. PUMP DOWN PLUG FROM 14,000' W/ MAX RATE OF AFPM, MAX PRESSURE 6,220 PSI. SET PLUG AT 20,040' PICK UP & 19,994'-96', 19,919'-21', INDICATIONS GUNS 1 & 2 FIRED. NO INDICATION GUN 3 FIRED. PUMPED BACK DOWN AND TRIED GUN 3 AGAIN. CALLED SUPERVISOR. TRIED GUN 4 AT CLUSTER 3 DEPTH, SHOWED SHORT ALSO, NO INDICATION FIRED. (03:50) POOH. (04:7) STOP AT 500 AND HSM. REMOVE ALL UNNECESSARY PERSONNEL FROM LOCATION. (05:00) OOH, ALL GUNS FIRED, WL OPERATOR SAID HE THINKS GUNS 3 & 4 FIRED AT SAME TIME AS GUN 2. CALLED SUPERVISOR. MU 2 GUNS TO RIH & FINISH STAGE 3 PERFS PERFORATING CLUSTERS 3 & RT. Page 1/2 Report Printed: 7/26/2016
12 Page 2/2 Report Printed: 7/26/2016
13 RIH & PERF STG 3 (3RD & 4TH CLUSTER), REPAIR T-BELT, FRAC STG 3, PERF & FRAC STG 4, PERF STG 5, RT. CONTINUE FRAC OPERATIONS 248, , :00 10: STG 3 (SECOND) GUN RUN: SIW W/ 4,400 PSI. RU E-LINE ON WELL. EQUALIZE LUBRICATOR AND OPEN WELL W/ 4,400 PSI. RIH (2) 2'x3-3/8" GUNS, 5 SPF, 60 DEG. PHASED. GET ON DEPTH W/ SH0RT 13,271'. PUMP DOWN PLUG FROM 14,000' W/ MAX RATE OF AFPM, MAX PRESSURE 7,700 PSI. PICK UP & MISFIRED. POOH TO EXAMINE GUNS. 500' AND CLEARED NON ESSENTIAL PERSONNEL TO COME OUT WITH LIVE GUNS. OOH 10:00. SI WITH 4200 PSI. 10:00 11: LD, DISARM AND BD GUNS. GUNS WERE NOT WIRED CORRECTLY, (THEY HAD BEEN WIRED TO SET PLUG, WE RAN DUMMY PLUG). PU NEW GUNS. NOTE: HES BROKE DOWN 1ST SET OF GUNS & FOUND THAT GUNS 2,3, &4 WERE WIRED WITH POSITIVE SWITCHES, (GUN 3 SHOULD HAD BEEN WIRED W/ NEGATIVE SWITCH), THIS ALLOWED ALL 3 GUNS TO SAME TIME. 11:15 14: STG 3 (THIRD) GUN RUN: SIW W/ 4,200 PSI. RU E-LINE ON WELL. EQUALIZE LUBRICATOR AND OPEN WELL W/ 4,100 PSI. RIH W (3) 2'x3-3/8" GUNS, 5 SPF, 60 DEG. PHASED. GET ON DEPTH W/ SH0RT 13,271'. PUMP DOWN PLUG FROM 14,000' W/ MAX RATE OF AFPM, MAX PRESSURE 7,006 PSI. PICK UP & 19,826'-28' & 19,738-40' (20 TOTAL HOLES, 60 TOTAL FOR STG 3) BBL USED FOR PUMP DOWN (ALL 3 RUNS). POOH. 14:30. SIW W/ 4,300 PSI. RD WIRELINE. ALL SHOTS FIRED. DROP BALL. NU FRAC CAP & TURN WELL OVER TO FRAC. 14:30 15: CONTINUE MAKING REPAIRS TO T-BELT. PRIME AND TEST. 15:45 20: (15:45) FRAC STAGE 3 PERFS 19,738' TO 19,996' AS FOLLOWS; TEST PUMP LINES TO 12,500 PSI. OPEN WELL W/ 4,203 PSI. BD ,705 PSI. FRAC W/ 4,000 GAL OF 15% FE ACID. 8,384 BBL OF PERMVIS VFR - 10 WATER, 1,250 BBLS OF PERM VIS W/ MICRO PROP, 5,460 BBLS OF LINEAR GEL, 77,244 LBS 100 COMMON WHITE, 295,480 LBS 40/70, 75,300 LBS 30/50 WHITE, & 50,296 LBS 30/50 OILPLUS SAND FROM 0.5 TO PPG. AIR 90 BPM, ATP 10,295 PSI. TOTAL LOAD TO RECOVER = 15,189 BBLS. ISIP 5,893 PSI, (0.85 FG) 5 MINS 5,037 PSI (20:01). NOTE: SD 10 MINS TO REPLACE AN O-RING ON PUMP IRON & HYD LINE LEAK ON T-BELT. COULD NOT GET GEL TO PUMP CORRECTLY AND HELD 1.3 PPG TO PUMP THE REMAINDER OF THE 40/70 SAND. THIS CAUSED US TO PUMP AN ADDITIONAL 13,850 GALLONS OF SLICKWATER. HELD 1.5 PPG THROUGH 30/50 AND PREMIUM PLUS SANDS. THIS CAUSED US TO PUMP AN ADDITIONAL 11,750 GALLONS OF SLICKWATER. 20:00 23: STG 4 PLUG & GUN RUN: SIW W/ 5,323 PSI. RU E-LINE ON WELL. EQUALIZE LUBRICATOR AND OPEN WELL W/ 4,667 PSI. RIH W HALLIBURTON 10K CFP AND (4) 2'x3-3/8" GUNS, 5 SPF, 60 DEG. PHASED. GET ON DEPTH W/ SH0RT 13,271'. PUMP DOWN PLUG FROM 14,000' W/ MAX RATE OF AFPM, MAX PRESSURE 5,394 PSI. SET PLUG AT 19,706' PICK UP & 19,664'-66', 19,580'-82', 19,496'-98' & 19,412'-14' (40 TOTAL HOLES). 342 BBL USED FOR PUMP DOWN. POOH. 23:08. SIW W/ 4,435 PSI. RD WIRELINE. ALL SHOTS FIRED. DROP BALL. NU FRAC CAP & TURN WELL OVER TO FRAC. 23:00 23: GREASED FRAC STACK. 23:30 00: (23:40) TEST PUMP LINES TO 12,500 PSI. (23:50) STANDBY FOR 2 SAND TRUCKS TO OFF LOAD SAND. (00:10) 00:15 04: (00:11) FRAC STAGE 4 PERFS 19,412' TO 19,666' AS FOLLOWS; TEST PUMP LINES TO 12,500 PSI. OPEN WELL W/ 4,305 PSI. BD ,645 PSI. FRAC W/ 4,000 GAL OF 15% FE ACID. 12,799 BBL OF PERMVIS VFR - 10 WATER, 1,250 BBLS OF PERM VIS W/ MICRO PROP, 905 BBLS OF LINEAR GEL, 77,726 LBS 100 COMMON WHITE, 291,360 LBS 40/70, 75,500 LBS 30/50 WHITE, & 50,120 LBS 30/50 OILPLUS SAND FROM 0.5 TO PPG. AIR 88.8 BPM, ATP 9,761 PSI. TOTAL LOAD TO RECOVER = 15,050 BBLS. ISIP 6,100 PSI, (0.86 FG) 5 MINS 5,043 PSI (03:48). NOTE: USED ALL SLICKWATER DUE TO GEL NOT HYDRATING THROUGH ADP. HIGHEST SAND CONCENTRATION WAS 1.5 PPG. WORKING ON NEW FORMULATIONS FOR GEL WITH PRODUCED WATER 04:00 06: STG 5 PLUG & GUN RUN: SIW W/ 5,430 PSI. RU E-LINE ON WELL. EQUALIZE LUBRICATOR AND OPEN WELL W/ 4,593 PSI. RIH W HALLIBURTON 10K CFP AND (4) 2'x3-3/8" GUNS, 5 SPF, 60 DEG. PHASED. GET ON DEPTH W/ SH0RT 13,271'. PUMP DOWN PLUG FROM 14,000' W/ MAX RATE OF AFPM, MAX PRESSURE 5,746 PSI. SET PLUG AT 19,370' PICK UP & 19,325'-27', 19,239'-41', 19,163'-65' & 19,076'-78' (40 TOTAL HOLES). 310 BBL USED FOR PUMP DOWN. RT. Page 1/2 Report Printed: 7/26/2016
14 Page 2/2 Report Printed: 7/26/2016
15 POOH STG 5 WL, FRAC STG 5, PERF & FRAC STG 6 & 7, PERF STG 8, OFFLOADING SAND FOR STG 8. OPEN 05:53 & FRACING STG RT. CONTINUE FRAC OPERATIONS 358, ,033, :00 07: CONTINUE POOH W/ WL BHA. 07:08. SIW W/ 4,400 PSI. RD WIRELINE. ALL SHOTS FIRED. DROP BALL. NU FRAC CAP & TURN WELL OVER TO FRAC. 07:15 08: REPAIR LEAK ON FRAC IRON, PRIME AND TEST. 08:00 11: (07:54) FRAC STAGE 5 PERFS 19,076' TO 19,327' AS FOLLOWS; TEST PUMP LINES TO 12,500 PSI. OPEN WELL W/ 4,295 PSI. BD ,925 PSI. FRAC W/ 4,000 GAL OF 15% FE ACID. 6,139 BBL OF PERMVIS VFR - 10 WATER, 1,250 BBLS OF PERM VIS W/ MICRO PROP, 6,857 BBLS OF LINEAR GEL, 78,850 LBS 100 COMMON WHITE, 294,976 LBS 40/70, 76,367 LBS 30/50 WHITE, & 49,001 LBS 30/50 OILPLUS SAND FROM 0.5 TO PPG. AIR 90.1 BPM, ATP 9,431 PSI. TOTAL LOAD TO RECOVER = 14,651 BBLS. ISIP 5,553 PSI, (0.82 FG) 5 MINS 5,074 PSI (11:26). 11:30 14: STG 6 PLUG & GUN RUN: SIW W/ 5,074 PSI. RU E-LINE ON WELL. EQUALIZE LUBRICATOR AND OPEN WELL W/ 4,400 PSI. RIH W HALLIBURTON 10K CFP AND (4) 2'x3-3/8" GUNS, 5 SPF, 60 DEG. PHASED. GET ON DEPTH W/ SH0RT 13,271'. PUMP DOWN PLUG FROM 14,000' W/ MAX RATE OF AFPM, MAX PRESSURE 5,500 PSI. SET PLUG AT 19,034' PICK UP & 18,992'-94', 18,908'-10', 18,824'-26' & 18,740'-42' (40 TOTAL HOLES). 305 BBL USED FOR PUMP DOWN. POOH, 14:15. SIW W/ 4,588 PSI. RD WIRELINE. ALL SHOTS FIRED. DROP BALL. NU FRAC CAP & TURN WELL OVER TO FRAC. 14:15 15: OFFLOAD SAND 15:00 15: SAFETY STAND DOWN AFTER HEAT STRESS INCIDENT. 15:15 18: (15:15) FRAC STAGE 6 PERFS 18,740' TO 18,994' AS FOLLOWS; TEST PUMP LINES TO 12,500 PSI. OPEN WELL W/ 4,477 PSI. BD ,131 PSI. FRAC W/ 4,000 GAL OF 15% FE ACID. 8,210 BBL OF PERMVIS VFR - 10 WATER, 1,250 BBLS OF PERM VIS W/ MICRO PROP, 4,208 BBLS OF LINEAR GEL, 78,100 LBS 100 COMMON WHITE, 295,244 LBS 40/70, 75,333 LBS 30/50 WHITE, & 49,579 LBS 30/50 OILPLUS SAND FROM 0.5 TO PPG. AIR 89.7 BPM, ATP 9,907 PSI. TOTAL LOAD TO RECOVER = 13,763 BBLS. ISIP 5,860 PSI, (0.84 FG) 5 MINS 5,051 PSI (18:48). 18:45 21: STG 7 PLUG & GUN RUN: SIW W/ 5,258 PSI. RU E-LINE ON WELL. EQUALIZE LUBRICATOR AND OPEN WELL W/ 4,773 PSI. RIH W HALLIBURTON 10K DFP AND (4) 2'x3-3/8" GUNS, 5 SPF, 60 DEG. PHASED. GET ON DEPTH W/ SH0RT 13,271'. PUMP DOWN PLUG FROM 14,000' W/ MAX RATE OF AFPM, MAX PRESSURE 5,570 PSI. SET PLUG AT 18,698' PICK UP & 18,656'-58', 18,572'-74', 18,488'-90', & 18,404'-06' (40 TOTAL HOLES). 282 BBL USED FOR PUMP DOWN. POOH. 21:40. SIW W/ 4,530 PSI. RD WIRELINE. ALL SHOTS FIRED. DROP BALL. NU FRAC CAP & TURN WELL OVER TO FRAC. 21:45 22: GREASED FRAC STACK. 22:30 02: (22:49) FRAC STAGE 7 PERFS 18,404' TO 18,658' AS FOLLOWS; TEST PUMP LINES TO 12,500 PSI. OPEN WELL W/ 4,439 PSI. BD ,848 PSI. FRAC W/ 4,000 GAL OF 15% FE ACID. 9,065 BBL OF PERMVIS VFR - 10 WATER, 1,250 BBLS OF PERM VIS W/ MICRO PROP, 3,538 BBLS OF LINEAR GEL, 77,780 LBS 100 COMMON WHITE, 296,220 LBS 40/70, 75,460 LBS 30/50 WHITE, & 51,500 LBS 30/50 OILPLUS SAND FROM 0.5 TO PPG. AIR 89.5 BPM, ATP 9,526 PSI. TOTAL LOAD TO RECOVER = 13,948 BBLS. ISIP 5,773 PSI, (0.84 FG) 5 MINS 5,021 PSI (02:13). 02:15 05: STG 8 PLUG & GUN RUN: SIW W/ 5,021 PSI. RU E-LINE ON WELL. EQUALIZE LUBRICATOR AND OPEN WELL W/ 4,731 PSI. RIH W HALLIBURTON 10K CFP AND (4) 2'x3-3/8" GUNS, 5 SPF, 60 DEG. PHASED. GET ON DEPTH W/ SH0RT 13,271'. PUMP DOWN PLUG FROM 14,000' W/ MAX RATE OF AFPM, MAX PRESSURE 5,226 PSI. SET PLUG AT 18,362' PICK UP & 18,320'-22', 18,234'-36', 18,157'-59' & 18,068'-70' (40 TOTAL HOLES). 270 BBL USED FOR PUMP DOWN. POOH. 05:01. SIW W/ 4,512 PSI. RD WIRELINE. ALL SHOTS FIRED. DROP BALL. NU FRAC CAP & TURN WELL OVER TO FRAC. 05:00 05: OFFLOADING SAND FOR STG 8 05:45 06: STG 8 FRAC; PRIME & TEST, OPEN 05:53. FRACING STG RT.
16 FRAC STG 8, PERF & FRAC STG 9 & 10, PERF STG 11, TURNING WELL OVER TO FRAC FOR STG RT. CONTINUE FRAC OPERATIONS. 18 STAGES TOTAL. 358, :00 09: (05:53) FRAC STAGE 8 PERFS 18,068' TO 18,322' AS FOLLOWS; TEST PUMP LINES TO 12,500 PSI. OPEN WELL W/ 4,407 PSI. BD ,144 PSI. FRAC W/ 4,000 GAL OF 15% FE ACID. 9,156 BBL OF PERMVIS VFR - 10 WATER, 1,250 BBLS OF PERM VIS W/ MICRO PROP, 3,123 BBLS OF LINEAR GEL, 78,740 LBS 100 COMMON WHITE, 296,160 LBS 40/70, 75,993 LBS 30/50 WHITE, & 51,180 LBS 30/50 OILPLUS SAND FROM 0.5 TO PPG. AIR 90.5 BPM, ATP 9,787 PSI. TOTAL LOAD TO RECOVER = 13,894 BBLS. ISIP 5,689 PSI, (0.83 FG) 5 MINS 5,045 PSI (09:18). 09:15 12: STG 9 PLUG & GUN RUN: SIW W/ 5,045 PSI. RU E-LINE ON WELL. EQUALIZE LUBRICATOR AND OPEN WELL W/ 4,680 PSI. RIH W HALLIBURTON 10K CFP AND (4) 2'x3-3/8" GUNS, 5 SPF, 60 DEG. PHASED. GET ON DEPTH W/ SH0RT 13,271'. PUMP DOWN PLUG FROM 14,000' W/ MAX RATE OF AFPM, MAX PRESSURE 5,716 PSI. SET PLUG AT 18,026' PICK UP & 17,984'-86', 17,900'-02', 17,816'-18' & 17,732'-34' (40 TOTAL HOLES). 255 BBL USED FOR PUMP DOWN. POOH. 12:30. SIW W/ 4,500 PSI. RD WIRELINE. ALL SHOTS FIRED. DROP BALL. NU FRAC CAP & TURN WELL OVER TO FRAC. 12:30 14: FRAC PUMP MAINT. AND WAITING ON SAND. 14:30 18: (14:29) FRAC STAGE 9 PERFS 17,732' TO 17,986' AS FOLLOWS; TEST PUMP LINES TO 12,500 PSI. OPEN WELL W/ 4,383 PSI. BD 9.9 7,880 PSI. FRAC W/ 4,000 GAL OF 15% FE ACID. 8,691 BBL OF PERMVIS VFR - 10 WATER, 1,250 BBLS OF PERM VIS W/ MICRO PROP, 4,153 BBLS OF LINEAR GEL, 78,012 LBS 100 COMMON WHITE, 299,108 LBS 40/70, 79,497 LBS 30/50 WHITE, & 43,090 LBS 30/50 OILPLUS SAND FROM 0.5 TO PPG. AIR 90 BPM, ATP 10,093 PSI. TOTAL LOAD TO RECOVER = 14,189 BBLS. ISIP 5,782 PSI, (0.84 FG) 5 MINS 5,293 PSI (18:01). 18:00 20: STG 10 PLUG & GUN RUN: SIW W/ 5,293 PSI. RU E-LINE ON WELL. EQUALIZE LUBRICATOR AND OPEN WELL W/ 4,757 PSI. RIH W HALLIBURTON 10K CFP AND (4) 2'x3-3/8" GUNS, 5 SPF, 60 DEG. PHASED. GET ON DEPTH W/ SH0RT 13,271'. PUMP DOWN PLUG FROM 14,000' W/ MAX RATE OF AFPM, MAX PRESSURE 5,662 PSI. SET PLUG AT 17,690' PICK UP & 17,648'-50', 17,564'-66', 17,480'-82' & 17,396'-98' (40 TOTAL HOLES). 223 BBL USED FOR PUMP DOWN. POOH. 20:37. SIW W/ 4,398 PSI. RD WIRELINE. ALL SHOTS FIRED. DROP BALL. NU FRAC CAP & TURN WELL OVER TO FRAC. 20:30 21: GREASED FRAC STACK. 21:00 00: (21:08) FRAC STAGE 10 PERFS 17,396' TO 17,650' AS FOLLOWS; TEST PUMP LINES TO 12,500 PSI. OPEN WELL W/ 4,394 PSI. BD ,395 PSI. FRAC W/ 4,000 GAL OF 15% FE ACID. 8,948 BBL OF PERMVIS VFR - 10 WATER, 1,250 BBLS OF PERM VIS W/ MICRO PROP, 3,498 BBLS OF LINEAR GEL, 76,982 LBS 100 COMMON WHITE, 296,488 LBS 40/70, 75,810 LBS 30/50 WHITE, & 53,366 LBS 30/50 OILPLUS SAND FROM 0.5 TO PPG. AIR 89.6 BPM, ATP 10,346 PSI. TOTAL LOAD TO RECOVER = 13,791 BBLS. ISIP 6,287 PSI, (0.88 FG) 5 MINS 5,267 PSI (00:29). 00:30 03: (00:30) SD WL RUN DUE TO LIGHTNING STORM PASSING OVER LOCATION. HALLIBURTON WL OPERATOR SAID THE COMPANY POLICY IS A LIGHTNING STRIKE WITHIN 10 MILES THEY HAVE TO SD FOR AT LEAST 30 MINS AND THEN CHECK CONDITIONS (03:37). 03:30 06: (03:37) STG 11 PLUG & GUN RUN: SIW W/ 5,267 PSI. RU E-LINE ON WELL. EQUALIZE LUBRICATOR AND OPEN WELL W/ 4,249 PSI. RIH W HALLIBURTON 10K DFP AND (4) 2'x3-3/8" GUNS, 5 SPF, 60 DEG. PHASED. GET ON DEPTH W/ SH0RT 13,271'. PUMP DOWN PLUG FROM 14,000' W/ MAX RATE OF AFPM, MAX PRESSURE 7,002 PSI. SET PLUG AT 17,354' PICK UP & 17,312'-14', 17,228'-30', 17,144'-46', & 17,060'-62' (40 TOTAL HOLES). 209 BBL USED FOR PUMP DOWN. POOH. 06:00. SIW W/ 4305 PSI. RD WIRELINE. ALL SHOTS FIRED. DROP BALL. NU FRAC CAP & TURN WELL OVER TO FRAC.
EP WELLS DAILY OPERATIONS REPORT Report 14 05/04/2017
5/5/27 5:5:26 Report Version: 4..6R9 Report 4 5/4/27 Company Type WBS No/API No PERMIAN Development UNIVERSITY 9 PW UNIT 56H UNIVERSITY 9 PW UNIT 56H 32656 / 4233326. Event Summary Event Type Completion
More informationDaily Drilling Report Onshore
Daily Drilling Well NameWellbore No.: UNIVERSITY EAST 4109KH00 Country: USA StateOCSG TEXAS FieldPermit#: WOLFCAMP EAST Supervisors: EngineerManager: MICHAEL AARON JAMES WILSON MOTLEY, DEREK MANGUM DANNY
More information2/4/15 SAU 1220DH WOCS: Aaron Auld Rig: WSI wireline/ rigless
2/4/15 SAU 1220DH WOCS: Aaron Auld Rig: WSI wireline/ rigless 07:30- Arrive on location. Held PJSM and discussed JSA w/ crew. R/U WSI wireline/ Key pump truck. Run CBL/GR/ CNL Logs. PBTD is 10,214. R/D
More informationAMERICAN ENERGY - PERMIAN BASIN, LLC Daily Completion Report UNIVERSITY SR HS AEPB WELL NO. 115
AMERICAN ENERGY - PERMIAN BASIN, LLC AEPB WELL NO. 115 4/10/16 Number of s (ft) Primary Job - ORIGINAL 57 Ground Elevation (ft) RKB (ft) Secondary Job 10,000 4/8/16 27,948 CONSLTNT, JASON COLLINSWORTH,
More informationFrac Talk Laura Schafer 4 March 2016
Frac Talk Laura Schafer 4 March 2016 My Path to Frac Education MS, BSc Chemical Engineering Colorado School of Mines Career Schlumberger 2002 2010 Well Services Manager Fracturing Cementing Coil Tubing
More informationOptimizing Perforating Charge Design
Optimizing Perforating Charge Design for Stimulation Fracturing Unconventional Reservoirs Deep Penetrating (DP) Charges Natural Completions Focused on depth of Penetration Hole size is usually an after
More informationOptimizing Completion Technology for Eastern European Shales
Optimizing Completion Technology for Eastern European Shales MARK VAN DOMELEN Senior Technical Advisor Technical Advisory Team Europe Halliburton Energy Services Current US Shale Gas Trends Increasing
More informationOil & Gas. Simplified Frac Iron System
Oil & Gas Simplified Frac Iron System 2 The shortest distance between two points is a straight line. Weir introduces that radical idea to the frac site. Simplicity delivered Consider the traditional frac
More informationHow to Simplify Your Frac Site. Presented by Firstname Surname, Job Title
How to Simplify Your Frac Site Presented by Firstname Surname, Job Title Firstname Surname, Job Title Firstname Surname, Job Title We engineer your success. WEIR Oil & Gas is committed to improving the
More informationOperating Instructions
SPIN-PULL THREADED INSERT TOOL Operating Instructions Read All Safety Rules and Instructions Carefully Save this manual for Future Reference Complete Seal Kit IMPORTANT SAFETY WARNINGS: THE SAFETY WARNINGS
More informationPARTS LIST FOR WC-150-0ME3 WATER CANNON. Copyright 2000, Mi-T-M Corporation Issue Date:
PARTS LIST FOR WC-150-0ME3 WATER CANNON Congratulations on the purchase of your new Mi-T-M Water Cannon! This parts listing has been complied for your benefit. You can be assured your Mi-T-M Water Cannon
More informationPARTS LIST FOR WC-100-0ME3 WATER CANNON. Copyright 2000, Mi-T-M Corporation Issue Date:
PARTS LIST FOR WC-100-0ME3 WATER CANNON Congratulations on the purchase of your new Mi-T-M Water Cannon! This parts listing has been complied for your benefit. You can be assured your Mi-T-M Water Cannon
More informationOperating Instructions
SPIN-PULL THREADED INSERT TOOL Operating Instructions Read All Safety Rules and Instructions Carefully Save this manual for Future Reference IMPORTANT SAFETY WARNINGS: THE SAFETY WARNINGS BELOW CANNOT
More informationJJ Joubert is a Data Architect and unofficially official PPDM advocate at Drilling Info. Currently he is working specifically with Completion data,
JJ Joubert is a Data Architect and unofficially official PPDM advocate at Drilling Info. Currently he is working specifically with Completion data, Directional Surveys, and Hydraulic fracturing and the
More informationE-Blotter Operation. Technical Bulletin E-03 MATERIAL PROCEDURE
E-Blotter Operation MATERIAL BSA (1 mg/ml; 0.05 g BSA (Sigma-Aldrich Ltd., St Louis, MO; U.S.A.) dissolve in 50 ml ddh 2 O, aliquot to 1 ml in micro-centrifuge tubes and freeze in -20 C) NK92 cell lysate
More informationFracHOOK TM MULTILATERAL FRACTURING SYSTEM
Mihai Marcu - Baker Hughes 2009 CADE / CAODC Calgary, AB 1 OVERVIEW Preamble What Are The Industry s Requirements? FracHOOK TM System Technical Features And Benefits FracHOOK TM System Economical Benefits
More informationFrac Manifold Systems. Increase operational efficiencies of simultaneous completion operations
Frac Manifold Systems Increase operational efficiencies of simultaneous completion operations Modular, flexible designs save time and money The equipment and technicians required to hydraulically fracture
More informationPTTC/DOE/RPSEA Gas Shales Workshop Marcellus Shale Hydraulic Fracturing
PTTC/DOE/RPSEA Gas Shales Workshop Marcellus Shale Hydraulic Fracturing > Arlington Virginia > September 28 th, 2011 > Jordan Ciezobka - GTI RPSEA Marcellus Gas Shale Project Objective To enhance shale
More information10XE AND 15XE Electric High-Pressure Washer
10XE AND 15XE Electric High-Pressure Washer 1-877-JD-KLEEN (1-877-535-5336) Motor Specs: 10XE 15XE Pump Oil Grade: Pump Oil Capacity: Nozzle Size: 10XE 15XE 1.5 HP / 1 Phase / 120 Volts 2.0 HP / 1 Phase
More informationSTERN TUBE SEAL STERN KEEPER C-TYPE MANUAL
STERN TUBE SEAL STERN KEEPER C-TYPE MANUAL C O N T E N T S CHAPTER 1 DESCRIPTION OF SAFETY 1 LIST OF WARNING 3 2 LIST OF CAUTION 4 CHAPTER 2 OUTLINE 5 1 INTRODUCTION 5 2 SPECIFICATION 5 2.1 SEAL TYPE 5
More informationThe Evolution of. Hydraulic Fracturing In the Bakken Petroleum System
The Evlutin f Hydraulic Fracturing In the Bakken Petrleum System 1 Murex Petrleum Crpratin is Driven t Be a Leader in the Willistn Basin Privately held upstream il & gas cmpany perating primarily in the
More informationComparative Proteomics Kit II: Western Blot Module Quick Guide
Comparative Proteomics Kit II: Western Blot Module Quick Guide Lesson 1 1 Label one 1.5 ml fliptop micro tube for each of five fish samples. Also label one screw-cap micro tube for each fish sample. 2.
More informationWHAT IS GEL ELECTROPHORESIS?
Getting Started With Gel Electrophoresis a world of learning Presented by Peter J Ball, Southern Biological. For further information, please contact the author by phone (03) 9877-4597 or by email peterjball@southernbiological.com.
More informationMilk Jug Glow Skull. Created by John Park. Last updated on :28:36 PM UTC
Milk Jug Glow Skull Created by John Park Last updated on 2018-09-14 09:28:36 PM UTC Guide Contents Guide Contents Overview Parts Materials & Tools Optional Skull/Sculpting Stand Build the Skull Prep the
More informationStandard Operating Procedures
Standard Operating Procedures (V1_4/7/16) Safe Working Practices for Leica Laser Micro Dissection Microscope Table of Contents I. General Information II. Facility Orientation and Training III. Startup
More informationFOOD GRADE EQUIPMENT LUBRICANTS
FOOD GRADE EQUIPMENT LUBRICANTS STOPLIGHT FOOD SAFETY PROGRAM MINIMIZE THE RISK OF FOOD CONTAMINATION Developed in response to a growing need within the industry to minimize the risk of food contamination
More informationAIRBRUSH SERIES. 取扱説明書 Operating Instruction Manual
AIRBRUSH SERIES 取扱説明書 Operating Instruction Manual ABSOLUTE PRECISION Experienced airbrush users who demand absolute precision and unmatched extreme detail spray choose Iwata Custom Micron Series airbrushes.
More informationA2A C172 Trainer. variables list and notes for simpit builders
A2A C172 Trainer variables list and notes for simpit builders Gauges: (L:AirspeedIndicatedNeedle,number) - airspeed needle (L:AirspeedTAS,number) - IAS/TAS conversion chart (range: 0 110) (A:ATTITUDE INDICATOR
More informationFLAKES, LIGHTNING FX & PASTE PEARLS TECHNICAL DATA SHEET
FLAKES, LIGHTNING FX & PASTE PEARLS TECHNICAL DATA SHEET Check local VOC DESCRIPTION Flakes are precision cut, resin coated chips for adding intense sparkle to custom paint jobs. Lightning FX are vibrant,
More informationInstruction Manual OmniPAGE Vertical Electrophoresis Units. Catalogue Numbers
Instruction Manual OmniPAGE Vertical Electrophoresis Units Catalogue Numbers VS10D, VS10DSYS, VS10PRE VS10D, VS10DSYS, VS10PRE, VS10DCAST VS10WD, VS10WDSYS VS20D, VS20DSYS, VS20DCAST, VS30D, VS30DSYS,
More informationInstruction Manual OmniPAGE Vertical Electrophoresis Units. Catalogue Numbers
Instruction Manual OmniPAGE Vertical Electrophoresis Units Catalogue Numbers CVS10D, CVS10DSYS, CVS10PRE VS10D, VS10DSYS, VS10PRE, VS10DCAST VS10WD, VS10WDSYS VS20D, VS20DSYS, VS20DCAST, VS30D, VS30DSYS,
More informationV-Solder BON-7103/7203
V-Solder BON-7103/7203 V-Cut solder machine (Applicable solder wire diameter φ0.3~φ0.8) Instruction manual (User s Manual) Preparation in Jyly 2010 The 7 th edition JAPAN BONKOTE CO.,LTD. Contents 1 Preface
More informationProduct Information. Fibre Glass and SMC should be dry sanded using European P240 / U.S. 240 grit paper. Not recommended for use over body filler
GLOBAL REFINISH SYSTEM AUTOMOTIVE REFINISH Product Information D8006 UHS Sealer D8006 UHS Sealer is a grey 2.8 VOC two-pack sealer for use under Global topcoat colors. D8006 must be activated with D8205
More informationLenis Needle-free Safety Syringe Device User Manual
Lenis Needle-free Safety Syringe Device User Manual 1 Table of Contents Welcome.3 Lenis Kit Components.4 Instructions 5-9 Maintenance and Care..10 Troubleshooting. 11 Warranty.12 Precautions 13 Return
More informationWorkshop Manual, Seal handbook part
Workshop Manual, Seal handbook part Mechanical seals for Large C-Pumps, L-Pumps and P-Pumps equipped with 605-series, 705-series, 805-series, 905-series drive units 894483/01 2 Seal handbook part, Large
More informationQuick Guide Unguator Technology - Competence from the Start
Quick Guide Unguator Technology - Competence from the Start Determinate mixing parameters, based on traditional pharmaceutical compounding: 1. Classification of the formulation according to its appropriate
More informationShaveMaster II. Block Ice Shaver Instruction Manual Model #1005. Cincinnati, OH USA. Part No Revised June 1996
Block Ice Shaver Instruction Manual Model #1005 Part No. 12354 Revised June 1996 Cincinnati, OH 45241-4807 USA SAFETY PRECAUTIONS HOW TO OPERATE THE SHAVEMASTER II MAIN SHAFT Rotates when motor is "ON".
More informationCyclone Sand Pro Debris Blower. Parts Catalog. Form Number Model No and up.
Form Number 3351-356 Cyclone Sand Pro 1000 Debris Blower Model No. 08857-240000001 and up. Parts Catalog Ordering Replacement Parts To order replacement parts, please supply the part number, the quantity,
More informationFiddy - the FTDI Clip
Fiddy - the FTDI Clip Created by Timothy Reese Last updated on 2018-08-22 03:57:42 PM UTC Guide Contents Guide Contents Overview FTDI is Great! Things you'll need: What You'll Learn: 3D Printing Assembly
More informationProperly Applying Loose Fitting Victoria 4 Clothing to Genesis or Genesis 2 Female in DAZ 3D
Properly Applying Loose Fitting Victoria 4 Clothing to Genesis or Genesis 2 Female in DAZ 3D Those of you who have every tried to use Auto-fit to apply loose-fitting, upper torso clothing items for Victoria
More informationwashable start stop washable Contour 5897 charge
washable start stop charge Contour 5897 washable www.braun.co.jp 2 3 4 5 6 1 2 3 4 washable start stop 6 5 11 charge Contour 5897 washable 7 8 9 10 7 7 washable washable start stop ble 8 9 clean charge
More information10,000 prize draw. Register online for HC5800 HC5600 HC5400. EXTRA year guarantee FREE rewards gallery
3 HC5800 HC5600 HC5400 Register online for 10,000 prize draw EXTRA year guarantee FREE rewards gallery Visit www.productregister.co.uk/remington. You must register within 28 days of purchase. Thank you
More informationVertical Gel Electrophoresis System. Instruction Manual
Vertical Gel Electrophoresis System Instruction Manual Catalog Nos. MV-10DSYS MV-10WDSYS MV-20DSYS www.majorsci.com service@majorsci.com Version 02A February 5, 2010 Contents:- 1) Safety Instructions 2
More informationKM-S824 Modern Salon Spa Pedicure Chair Plumbing Free
KM-S824 Modern Salon Spa Pedicure Chair Plumbing Free NOTE: There is a wiring harness (see arrow) that needs to be connected from under the seat cushion to the back of the Chair Back. Keller International
More informationHIGH PERFORMANCE PLUS SERIES MANUAL & PARTS GUIDE ONLY FROM IWATA-MEDEA
HIGH PERFORMANCE PLUS SERIES MANUAL & PARTS GUIDE High-Precision, High-Detail Work distinguish these airbrushes as High Performance Plus! ONLY FROM IWATA-MEDEA Iwata airbrushes are designed for the demanding
More informationFiddy - the FTDI Clip
Fiddy - the FTDI Clip Created by Timothy Reese Last updated on 2016-11-22 09:18:04 PM UTC Guide Contents Guide Contents Overview FTDI is Great! Things you'll need: What You'll Learn: 3D Printing Assembly
More informationSTILL LIFE. Ryan Lee
STILL LIFE by Ryan Lee 1. FADE IN: EXT. RURAL ROAD - NIGHT A rusty 1976 Buick Regal sputters and rolls to a stop on a gravel road. Under the moonlight, plowed fields and thick woods sprawl in all directions.
More informationProfessional Hair Removal System
pearl PRO Professional Hair Removal System Carefully read this manual before using this appliance. Ensure that you know how the appliance functions and how to operate it. Instructions for Use 1 Safety
More informationFruit and Vegetable mask in 3 minutes
100% Natural Mask Machine Fruit and Vegetable mask in 3 minutes User s Manual 1 INTRODUCTION Congratulations on your Vitamask purchase! Now you can enjoy giving your skin the rejuvenation it needs in the
More informationKT-3010D Hair Steamer Rolling Stand Type
KT-3010D Hair Steamer Rolling Stand Type A B C A) Assembled unit reservoir bottle hanging in the front. B) Back of the unit showing the black rubber cap for draining the water. C) Water Bottle and Steamer
More informationArtesian Pedicure System
Installation Requirements Installation of the Collins pedicure unit is straightforward and comparable to installation of a residential hot tub or whirlpool. The utility requirements are as follow: 1 ½
More informationHow to Give a Subcutaneous (SC) Injection to Your Child
How to Give a Subcutaneous (SC) Injection to Your Child Supplies: Needles and syringes Alcohol swabs and gauze Vial with the drug solution Sharps container (Health Facts for You #4587) Band-Aids Distraction
More informationOMNI Coupling System. Cast Couplings Straight & Reducing Transitions IMPORTANT LINKS. Description: Cast Couplings
OMNI Coupling System Cast Couplings Straight & Reducing Transitions 441 IMPORTANT LINKS Click appropriate words to go to: Standard Limited Warranty Sales Terms & Conditions Freight Policy Returns Policy
More informationANEST IWATA CORPORATION Yokohama, Japan +81-(0)
2 NEED ASSISTANCE If you have any issues or warranty service questions, contact your local ANEST IWATA affiliate before returning to your place of purchase. ANEST IWATA-MEDEA, INC. Portland, Oregon U.S.A.
More informationSo... You Want To Use The 3D Printers
So... You Want To Use The 3D Printers 3D Printing Overview When a student would like to use the 3D Printers: 1. They should contact a supervisor and prepare the build plate. 2. Supervisors will level the
More informationCircuit Playground Express Head-Tilt Ears
Circuit Playground Express Head-Tilt Ears Created by Dave Astels Last updated on 2018-10-09 04:07:03 PM UTC Guide Contents Guide Contents Overview Parts Circuit Playground Express Micro servo Lithium Ion
More informationVALUE, QUALITY & PERFORMANCE distinguish these airbrushes!
BS If it s quality your looking for then Iwata will deliver straight from the box with no tweaking required with absolute excellence that comes from the Iwata product. What about parts, Airbrush Megastore
More information3D Printing Guide: MakerBot Replicator 2X
SOUTHERN POLYTECHNIC STATE UNIVERSITY 3D Printing Guide: MakerBot Replicator 2X Operating and Troubleshooting Guide Architecture Department 8/13/2014 Revision Table Version Dated Description By 1.00 06/25/2014
More informationPersonal Care. Global solutions, world class expertise, where you need them, all the time
Personal Care Global solutions, world class expertise, where you need them, all the time Complete Personal Care Packaging Solutions Rieke Dispensing is the global leader in dispensing solutions, offering
More informationProcedure 30 Collecting A Blood Specimen Using The Vacuum-Tube System. Procedure 31 Collecting A Blood Specimen Using A Needle And Syringe
Chapter 6 Phlebotomy Procedure 29 Performing A Venipuncture Procedure 30 Collecting A Blood Specimen Using The Vacuum-Tube System Procedure 31 Collecting A Blood Specimen Using A Needle And Syringe Procedure
More informationXS S M L XL 2XL 3XL 4XL 5XL Chest Collar
INFORMATION Mens Size Guide XS S M L XL 2XL 3XL 4XL 5XL Chest 30-32 34-36 38-40 42-44 46-48 50-52 54-56 58-60 62-64 Collar 14 14.5 15.5 16.5 17.5 18.5 19.5 20.5 21.5 Ladies Size Guide Ladies 8 10 12 14
More informationHammer Time Mini Golf Hazard with Crickit
Hammer Time Mini Golf Hazard with Crickit Created by John Park Last updated on 2018-07-09 06:47:53 AM UTC Guide Contents Guide Contents Overview Please Hammer, Don't Hurt Em Parts Materials & Tools Program
More informationTent Lantern. Created by Timothy Reese. Last updated on :17:25 AM UTC
Tent Lantern Created by Timothy Reese Last updated on 2017-07-14 05:17:25 AM UTC Guide Contents Guide Contents Overview Things you'll need: What You'll Learn: 3D Printing Code Assembly Wiring Diagram Soldering
More informationSlider Crank Mechanism -- from Cardboard and Craft Sticks
Slider Crank Mechanism -- from Cardboard and Craft Sticks Created by John Park Last updated on 2018-08-22 04:07:21 PM UTC Guide Contents Guide Contents Overview Materials Tools Build the Slider Crank Build
More informationModifying Servos for Continuous Rotation
Modifying Servos for Continuous Rotation Created by Rick Winscot Last updated on 2018-01-13 05:46:39 AM UTC Guide Contents Guide Contents Overview Tools / Materials Void the Warranty Breaking Bad Barriers
More informationTattoo Machine Engraving C. Zammiello 2007
Tattoo Machine Engraving C. Zammiello 2007 The tattoo machine is an instrument developed and used by tattoo artists that lends itself directly to the intaglio process as a form of direct engraving on metal
More informationROTARY PEN USER MANUAL
ROTARY PEN USER MANUAL 1. Overview The Helios Rotary Pen was created to give the artist pinpoint precision and unparalleled control during a tattoo procedure. The Helios Rotary Pen is an extremely versatile
More informationMEN S DRIFTER PREMIUM LEATHER JACKET
MEN S DRIFTER PREMIUM LEATHER JACKET rear exhaust vent Built for speed and comfort - this high quality jacket delivers in function as much as it does in style and comfort. MOSSI MEN S DRIFTER PREMIUM LEATHER
More informationComponents and Price List Pricing as at 8th February, 2018
Components and Price List Pricing as at 8th February, 2018 Anything can be organised with Elfa. It's fully customisable with a broad range of specialty components. - Swedish designed durable epoxy bonded
More information4950S ULTRA PRODUCTIVE ADDITIVE
4950S ULTRA PRODUCTIVE ADDITIVE GENERAL DESCRIPTION A flex additive designed to improve the adhesion, chip resistance and flexibility of Cromax ultra productive primer over rigid, semi-flexible and fully-flexible
More informationSterilization A Training Module
Sterilization A Training Module In This Training Module, You Will Learn: Definition of sterilization and disinfection What needs to be sterilized and disinfected What Personal Protective Equipment is required
More informationPrint Promotion conferences Praepen Jangmongkol
Print Promotion conferences 2013 Praepen Jangmongkol E.C.H. Will & Pemco & Kugler-Womako Slide 2 Our companies have a global network With production sites in Europe and North America and a global network
More informationDocument A: The Daily Express
Document A: The Daily Express The Daily Express is an English newspaper founded in 1900. Like other English newspapers, it printed daily news and stories on the war. Here is an excerpt written by correspondent
More informationVERSATILITY, RELIABILITY & PERFORMANCE distinguish these airbrushes as Eclipse!
Congratulations on the purchase of your Iwata Eclipse airbrush, a versatile, reliable and high-performance airbrush. We designed this Eclipse for the exacting needs of the artist who requires a multi-purpose,
More informationTECHNICAL INFORMATION
TECHNICAL INFORMATION TURCO DY-CHEK INDUSTRIAL PENETRANT (STEP 2) BY THE HAND WIPE OR SOLVENT REMOVAL METHOD DESCRIPTION: TURCO DY-CHEK INDUSTRIAL PENETRANT INSPECTION is a method of non-destructive testing
More informationCANDY CONCENTRATES TECHNICAL DATA SHEET
CANDY CONCENTRATES TECHNICAL DATA SHEET Check local VOC DESCRIPTION Candy Concentrates is a vibrant line of transparent pigments that add spectacular color to custom paint jobs. FEATURES Outstanding depth
More informationATS-SOI-5731 Page: 1 of 5. Approval Block. Prepared by: Signature Date Margaret Crouse 18 JUN Reviewed by: Signature Date
ATS-SOI-5731 Page: 1 of 5 Approval Block Prepared by: Signature Date Margaret Crouse 18 JUN 2014 Reviewed by: Signature Date Brian Flynn 18 JUN 2014 Approved by: Signature Date Kristal Jewell 18 JUN 2014
More informationFOR REFERENCE ONLY. TASK Hazards Who is at risk? Rick Level Mitigation Measures required: Working in unfamiliar environments for exhibition/event
FOR REFERENCE ONLY TASK Hazards Who is at risk? Rick Level Mitigation Measures required: Working in unfamiliar environments for exhibition/event Inadequate action due to procedures and facility unfamiliar
More informationOwner s Manual. Table of contents 2. Introuduction & Safty Standard 3. Important considerations 4. Identify Parts & Description 5.
Owner s Manual Table of contents 2 Introuduction & Safty Standard 3 Important considerations 4 Identify Parts & Description 5 Massage System 6 Toepia Chair Assembly 7 Toepia LX Armrest Assembly Toepia
More informationWILLOWWOOD ONE TRANSTIBIAL SYSTEM
WILLOWWOOD ONE TRANSTIBIAL SYSTEM User Instructions Thank you for using the WillowWood One System. Please follow these steps to ensure the most comfort and longest life from the system: Read and follow
More informationnames 1 inch + Black Vis-à-Vis Black Sharpie
Types of Covalent Compounds: Polar and Nonpolar If you ever had a piece of paper get wet, you ve noticed that the ink making up the lines of the paper or the ink from your carefully collected notes travel
More informationB-SERIES CONVERSION INSTRUCTIONS
B-SERIES CONVERSION INSTRUCTIONS The B-SERIES inks are designed to replace the OEM ink set for the Brother GT3 Direct To Garment printer. These inks are designed with high performance capabilities, 35
More informationCongratulations on your purchase of a. airbrush. CN GRAVITY-FEED DUAL-ACTION AIRBRUSH. color cup. main lever. needle cap. nozzle cap.
NEO SERIES MANUAL Congratulations on your purchase of a airbrush. color cup needle cap CN GRAVITY-FEED DUAL-ACTION AIRBRUSH main lever nozzle cap handle TO AIRBRUSH CN GRAVITY-FEED DUAL-ACTION AIRBRUSH
More informationOptiblot Non-Reducing Electrophoresis Kit
Optiblot Non-Reducing Electrophoresis Kit Instructions for Use For the use in non-reducing SDS-PAGE with precast gels This product is for research use only and is not intended for diagnostic use. 1 Table
More informationPLAS-STICK A-2330S POLYOLEFIN ADHESION PROMOTER
PLAS-STICK A-2330S POLYOLEFIN ADHESION PROMOTER GENERAL DESCRIPTION A green-gray polyolefin adhesion promoter designed to enhance the performance of products on unprimed polyolefin or non-polyolefin plastic
More informationKlein Tools Branded Collection. 3 rd Edition
Klein Tools Branded Collection 3 rd Edition Branded Collection Product Index T-Shirts..................... Page 4 Polo Shirts.................. Page 6 Athletic Wear.............. Page 13 Kids........................
More informationCrickit Dancing Marionette Kit Created by Dano Wall. Last updated on :03:11 PM UTC
Crickit Dancing Marionette Kit Created by Dano Wall Last updated on 2019-04-04 07:03:11 PM UTC Overview This project demonstrates how to build a robotic marionette that is controlled with four arcade-style
More informationWind Blowing Emoji Prop
Wind Blowing Emoji Prop Created by John Park Last updated on 2018-08-22 04:05:17 PM UTC Guide Contents Guide Contents Overview Code it with MakeCode Start Up Variables On Loud Sound If - Else Iterate Debounce
More informationCoffee Detonator: The TNT Plunger Grinder
Coffee Detonator: The TNT Plunger Grinder Created by John Park Last updated on 2017-04-12 08:04:36 PM UTC Guide Contents Guide Contents Overview Materials Voltage Conversion AC/DC Voltage Divider Microcontroller
More informationOptiblot SDS-PAGE Gel
Optiblot SDS-PAGE Gel Instructions for Use For the use in SDS-PAGE with precast gels This product is for research use only and is not intended for diagnostic use. 1 Table of Contents 1. Introduction 3
More informationSTAINLESS VALV A MANLEY VALVE FOR EVERY APPLICATION CHOOSE FROM ONE OF FIVE SERIES OF STAINLESS VALVES
1960 SWARTHMORE AVENUE LAKEWOOD, JERSEY 08701 STAINLESS VALV A MANLEY VALVE FOR EVERY APPLICATION CHOOSE FROM ONE OF FIVE SERIES OF STAINLESS V PERFORMANCE SERIES Stainless Steel ( XH-422 Exhaust and NK-840
More informationPART V: Uniform Information
Mackinac Island Honor Scouts Training Manual PART V: Uniform Information UNIFORM INFORMATION 1 UNIFORM INFORMATION The Mackinac Island Honor Scout uniform has remained basically the same over the years.
More informationProduct Data 367 Acrynamel
Product Data 367 Acrynamel PRODUCTS 367 Acrynamel Colour 367 Reducer R303-Normal Conditions, R203-Hot Conditions Product Description 367 Acrynamel is a single pack, fast drying, premium acrylic alkyd based
More informationFresh & Funky Fall by Tracy Meola
Fresh & Funky Fall by Tracy Meola Fresh & Funky Fall By Tracy Meola Palette: DecoArt Americana Antique Gold 13009 Burnt Orange 13016 Burnt Sienna 13063 Cherry Red 13159 Dark Chocolate 13065 Driftwood 13171
More informationHEAT STRESS HEAT STRESS IS 100% PREVENTABLE 276 PHASE CHANGE
BRINGING THE BEST OF THE WORLD TO YOU HEAT STRESS IS 100% PREVENTABLE EACH YEAR, MILLIONS OF WORKERS ARE EXPOSED TO POTENTIAL HEAT STRESS. INJURIES RELATED TO HEAT STRESS RANGE FROM DIZZINESS TO DEATH.
More informationBASKETBALL OUTFIT YOUR TEAM ADULT & YOUTH STOCK UNIFORMS TOPS BOTTOMS LADIES & GIRLS STOCK UNIFORMS TOPS BAGS...
OUTFIT YOUR TEAM UNIFORMS BASKETBALL JERSEYS SHORTS BAGS 1060 197 788 ADULT & YOUTH STOCK UNIFORMS... 60 TOPS... 67 BOTTOMS... 72 1065 865 1770 LADIES & GIRLS STOCK UNIFORMS... 76 TOPS... 81 BAGS... 82
More information3-D Printed Parts (Part 2)
3-D Printed Parts (Part 2) Post-processing 3-D printing with ABS plastic provides tremendous versatility when it comes to post-processing of your part. When we refer to post-processing, we are simply talking
More informationWINDOWS, DOORS AND FAÇADE ELEMENTS MADE OF ALUMINIUM. Operation, maintenance and care
RAICO WINDOWS, DOORS AND FAÇADE ELEMENTS MADE OF ALUMINIUM Operation, maintenance and care Contents 1. Hazard Notes 2. Operation Windows and French doors 2.1 Tilt & Turn element 2.2 Turn-Only element 2.3
More informationCustomer Service Manual
Customer Service Manual Updated: March 27, 2017 Table of Contents Uniforms/Attire. 3 Name Tags.. 3 Shirt/s Uniforms...... 3 Personal Appearance.... 4 Communication Etiquette...5 Phones.. 5 In Person..
More information3DPrinted Custom Keycaps
3DPrinted Custom Keycaps Created by Ruiz Brothers Last updated on 2016-09-05 07:20:30 PM UTC Guide Contents Guide Contents Overview Custom Keycaps Easy to install Accessibility Project Expectations Parts
More information