Operating Instructions...1 Setting The Time Movement And Precession

Transcription

1 INFORMATION MANUAL Operating Instructions....1 Setting The Time Movement And Precession Product Care Precautions And Recommendations Changing The Battery Bands Water Resistance Warranty Contact Information

2 OPERATING INSTRUCTIONS SETTING THE TIME 1. Pull the crown out to Position Turn the crown to set the hour, minute and seconds hands to the desired time. 3. Push the crown back in to Position 1. MOVEMENT AND PRECISION RAKANI uses Japanese quartz movements to ensure the most accurate time precision. Quartz movements are battery powered and do not require any additional winding. PRODUCT CARE PRECAUTIONS AND RECOMMENDATIONS Temperature: Chemical products: Cleaning: Avoid exposing the watch to extreme temperatures (less than 0 C/32 F or greater than 60 C/140 F) or extreme temperature changes. Avoid any part of the watch or band being in direct contact with strong chemical products such as solvents, detergents, cleaning supplies, perfumes, cosmetics, etc. Clean your watch regularly to maintain the aesthetic appeal and good working condition. A soft cloth or brush can be used for cleaning. CHANGING THE BATTERY A worn out battery should be replaced immediately to reduce the risk of damaging other parts of the watch. RAKANI watches utilize a fit case back to provide the most protection against air and water. Due to the air tight pressure of fit case backs a watch press tool is needed to securely fit the case back after it has been removed. Therefore, RAKANI recommends having the battery replaced by a jeweler or professional that has a watch press. Instructions on manually changing the battery are below

3 Battery Type: SR626SW Tools Needed: Flathead Screwdriver and Watch Press Instructions: 1. Find the slightly raised opening between the case back and the case. 2. Insert the edge of the flathead screwdriver in this opening. 3. Slightly force the screwdriver into the opening and lift up until the case back pops off. 4. Remove any protective casings. 5. Remove and replace the existing battery. 6. Replace any removed protective casings. 7. Put the case back in place by matching the small notch in the case back with the crown of the watch. 8. Use the watch press to securely fit the case back on. Make sure to align the watch press tool with the outer watch case and NOT on the watch crystal. Continue pressing until the entire case back is securely fit in place. BANDS Leather Bands Product Care and Cleaning: Avoid contact with water or damp items. Avoid prolonged exposure to sunlight. Avoid contact with products that have strong chemicals or greasy substances. Clean leather bands with a soft cloth. Metal Bands Product Care and Cleaning: Clean metal bands periodically using a soft brush with mild, soapy water. Be sure to dry the band thoroughly with a soft cloth. Adjusting Links: Tools Needed: Bracelet Holder, Pin Pusher, Pliers Instructions To Remove Links: 1. Open the clasp on the bracelet. 2. Look on the inside of the bracelet and locate the arrows near the clasp. 3. Place the band into the appropriate slot of the bracelet holder with the arrows pointing down. 4. Center the desired pin to be removed over one of the holes in the bottom of the bracelet holder. 5. With the pin pusher, push the pin as far as possible through the link. 6. Remove the watch from the bracelet holder and pull out the pin entirely with the pliers. 7. Repeat with other links until appropriate links are removed. Instructions To Put Links Together: 1. Line up the holes of the links. 2. Put the pin through the holes of both links. 3. Use the pin pusher to push the pin through the entire way until the pin is no longer sticking out on either side

4 WATER RESISTANCE The water resistance for each watch is specified on the case back etching. The chart below indicates acceptable activities which may expose the watch to water. For leather bands it is best to avoid all contact with water or moisture. WARRANTY All RAKANI watches come with a warranty against manufacturer defects for a period of 2 years from the time of purchase. The warranty ensures repair of the watch will be attempted in a timely manner and at no additional cost. If the watch is deemed unrepairable RAKANI will provide a new replacement of the same product, if available, or a similar product at RAKANI s discretion. The warranty covers: Movement Hands Dials The warranty does not cover: Batteries Watch bands Wear and tear Water damage, unless within the water resistance guidelines Accidental or negligent damage by a non-rakani authorized service provider - 3 -

5 Should you have any questions or would like to request service covered by the warranty please with the following information: Your contact information Order number Explanation of item in question Copy of receipt ( receipt or scanned copy) We will confirm the watch is under warranty and send further instructions. CONTACT INFORMATION RAKANI is dedicated to ensuring the quality of its products and satisfaction of its customers. Please contact us at should you have any questions, concerns or feedback