REFERENCE CP_TSSPEC_272 0 DATE: OCTOBER 2018 PAGE: 1 OF 13 SPECIFICATION FOR FOOT PROTECTION TABLE OF CONTENTS

Transcription

1 TITLE SPECIFICATION FOR FOOT PROTECTION REFERENCE REV CP_TSSPEC_272 0 DATE: OCTOBER 2018 PAGE: 1 OF 13 TABLE OF CONTENTS Page FOREWORD... 2 INTRODUCTION SCOPE NORMATIVE REFERENCES DEFINITIONS AND ABBREVIATIONS REQUIREMENTS QUALITY MANAGEMENT ENVIRONMENTAL MANAGEMENT HEALTH AND SAFETY... 4 Annex A - Bibliography... 5 Annexure C - Technical schedules A and B for Safety Shoes... 6 Technical schedules A and B... 7 Deviation schedule for Safety Shoes... 7 Annexure C - Technical schedules A and B for Safety Boots... 8 Technical schedules A and B... 9 Deviation schedule for Safety Boots... 9 Annexure C - Technical schedules A and B for Gumboot...10 Annex B - Revision information...11 Annex D Stock Items...12

2 PAGE 2 OF 13 FOREWORD Recommendations for corrections, additions or deletions should be addressed to the: Technology Services General Manager City Power Johannesburg (SOC) Ltd P O Box Booysens 2016

3 PAGE 3 OF 13 INTRODUCTION City Power personnel routinely carry out work in close proximity to electrical equipment. Whilst every possible safety precaution is followed, the employer is obliged to provide overalls which will give personnel the maximum possible degree of safety whilst, simultaneously, being comfortable enough not to restrict movement or cause discomfort. 1 SCOPE This specification covers City Power s requirements for the foot protection in accordance with the requirements SANS NORMATIVE REFERENCES The following documents contain provisions that, through reference in the text, constitute requirements of this specification. At the time of publication, the editions indicated were valid. All standards and specifications are subject to revision, and parties to agreements based on this specification are encouraged to investigate the possibility of applying the most recent editions of the documents listed below; SANS 724 Personal protective equipment and protective clothing against the thermal hazards of an electric arc flash. SANS 492- Protective and Safety Gum boots (Part 4), All made from Rubber DSP 34- Safety Shoes Electrical Testing Specification. SANS 741- Industrial boots (including Safety Boots) with Direct-vulcanized Soles and Heels SANS Industrial Boots (including Safety Boots) with Stuck-on Pre-moulded or Direct-injection - Moulded Soles and Heels SANS Industrial Shoes (including safety shoes) with Stuck-on Pre-moulded or Direct-injection - Moulded Soles and Heels SANS Industrial Shoes (including Safety Shoes) with Direct Vulcanised Soles and Heels 3 DEFINITIONS AND ABBREVIATIONS PPE HRC Personal Protective Equipment Hazard Risk Category 4 REQUIREMENTS 4.1 Safety boots/shoes General requirements a) The boots/shoes must be black b) The Material shall be full grain upper leather c) The design shall be in accordance with SANS and certified Test Safety shoes and safety boots shall be tested as per ASTM F2412 and ISO Packaging and labelling a) The safety shoes and boots shall be packed in a box. b) The box shall be adequately labeled and show the shoe or boot size c)

4 PAGE 4 OF Gumboots General requirements a) Gumboots shall be made of solid rubber and shall be black in colour with a protective toe cap. b) The gumboot shall be a knee length c) Gumboots shall comply with SANS Test Gumboots shall comply with. ISO Packaging and labelling a) The gumboots shall be packed in a box. b) The box shall be adequately labeled and show the gumboot size 4 QUALITY MANAGEMENT A quality management plan shall be set up in order to assure the proper quality management of the foot protection during design, development, production, installation and servicing phases. Guidance on the requirements for a quality management plan may be found in the SANS ISO The details shall be subject to agreement between City Power and the Supplier. 5 ENVIRONMENTAL MANAGEMENT An environmental management plan shall be set up in order to assure the proper environmental management of the foot protection throughout its entire life cycle (i.e. during design, development, production, installation, operation and maintenance, decommissioning and disposal phases). Guidance on the requirements for an environmental management system may be found in SANS ISO standards. The details shall be subject to agreement between City Power and the Supplier. This is to ensure that the asset created conforms to environmental standards and City Power SHEQ Policy. 6 HEALTH AND SAFETY A health and safety plan shall be set up in order to ensure proper management of the foot protection and compliance of the queuing system during installation, operation, maintenance, and decommissioning phases. Guidance on the requirements of a health and safety plan may be found in OHSAS standards. This is to ensure that the asset conforms to standard operating procedures and City Power SHERQ Policy. The details shall be subject to agreement between City Power and the Supplier.

5 PAGE 5 OF 13 Annex A - Bibliography none

6 PAGE 6 OF 13 Annexure C - Technical schedules A and B for Safety Shoes Schedule A: Purchaser's specific requirements Schedule B: Guarantees and technical particulars of equipment offered Item Description Schedule A Schedule B 1 Workplace safety shoes comply to specification Yes/no 2 Compliance to SANS SANS no 3 Documentation supplied Yes/no Note: Ticks, Cross [, X], Astrick [*], Word [Noted] or TBA [ To Be Advice ] will not be accepted Tender Number: Tenderer s Authorised Signatory: Name in block letters Signature Full name of company:

7 PAGE 7 OF 13 Technical schedules A and B Deviation schedule for Safety Shoes Any deviations offered to this specification shall be listed below with reasons for deviation. In addition, evidence shall be provided that the proposed deviation will at least be more cost-effective than that specified by City Power. Item Sub-clause of CP_TSSPEC_XXX Proposed deviation Tender Number: Tenderer s Authorised Signatory: Name in block letters Signature Full name of company:

8 PAGE 8 OF 13 Annexure C - Technical schedules A and B for Safety Boots Schedule A: Purchaser's specific requirements Schedule B: Guarantees and technical particulars of equipment offered Item Description Schedule A Schedule B 1 Workplace Safety boots comply to specification Yes/no 2 Compliance to SANS SANS no 3 Documentation supplied Yes/no Note: Ticks, Cross [, X], Astrick [*], Word [Noted] or TBA [ To Be Advice ] will not be accepted Tender Number: Tenderer s Authorised Signatory: Name in block letters Signature Full name of company:

9 PAGE 9 OF 13 Technical schedules A and B Deviation schedule for Safety Boots Any deviations offered to this specification shall be listed below with reasons for deviation. In addition, evidence shall be provided that the proposed deviation will at least be more cost-effective than that specified by City Power. Item Sub-clause of CP_TSSPEC_XXX Proposed deviation Tender Number: Tenderer s Authorised Signatory: Name in block letters Signature Full name of company:

10 PAGE 10 OF 13 Annexure C - Technical schedules A and B for Gumboot Schedule A: Purchaser's specific requirements Schedule B: Guarantees and technical particulars of equipment offered Item Description Schedule A Schedule B 1 Workplace Gumboot comply to specification Yes/no 2 Compliance to SANS SANS no 3 Documentation supplied Yes/no Note: Ticks, Cross [, X], Astrick [*], Word [Noted] or TBA [ To Be Advice ] will not be accepted Tender Number: Tenderer s Authorised Signatory: Name in block letters Signature Full name of company:

11 PAGE 11 OF 13 Annex B - Revision information DATE REV. NO. NOTES October First issue

12 PAGE 12 OF 13 Annex D Stock Items Material Group: PERSONAL PROTECTIVE EQUIPMENT Item SAP No SAP Short Description SAP Long Description Shoes safety (size 4) (size 4) Shoes safety (size 5) Shoes safety (size 5) Shoes safety (size 6) Shoes safety (size 7) Shoes safety (size 8) Shoes safety (size 9) Shoes safety (size 10) Shoes safety (size 11) Shoes safety (size 12) Shoes safety (size 13) Boots safety (size 4) Boots safety (size 5) Boots safety (size 6) Boots safety (size 7) Boots safety (size 8) Boots safety (size 9) Boots safety (size 10) (size 6) (size 7) (size 8) (size 9) (size 10) (size 11) (size 12) (size 13) (size 4) (size 5) (size 6) (size 7) (size 8) (size 9) (size 10)

13 PAGE 13 OF Boots safety (size 11) Boots safety (size 12 ) Boots safety (size 13 ) Gumboots (size 4) Gumboots(size 5) Gumboots (size 6) Gumboots (size 7) Gumboots (size 8) Gumboots (size 9) Gumboots (size 10) Gumboots (size 11) Gumboots (size 12) (size 11) (size 12 ) (size 13 ) (size 4) (size 5) (size 6) (size 7) (size 8) (size 9) (size 10) (size 11) (size 12)