ULTRA Getting Started Visit www.howtonono.com for Videos, Tips & Tricks
A Quick Introduction to no!no! READ this entire GETTING STARTED guide before using the no!no! to ensure safety and results. 1 2 3 4 Insert Tip Turn On Wide Tip Narrow Tip Charge & Uncover Choose Tip
How to no!no! 5 6 7 Get Started Set Treatment Level Glide Buff
Before Your First Treatment CHARGE the device for at least 5 hours. > Charging is complete when the Battery Icon on the status screen stops blinking. > Unplug the Charger from the wall and the device once charging is complete. Preparation > Cleanse the treatment area thoroughly, removing all lotions, oils, gels or creams before use.
Wide Tip Narrow Tip > Use the Wide Tip to treat large areas like the arms, legs, chest and back. > Use the Narrow Tip for small sensitive areas like the face, neck, underarms and bikini line. Note: > The no!no! ULTRA supports an optional range of Beauty Tips that transform the device into a complete beauty tool. How to no!no! Select Your Thermicon Tip
A Insert the Thermicon Tip [FIGURE A] INSERTING the Thermicon Tip > Make sure the device is turned off. > Hold no!no! in one hand and the Tip in the other. > Make sure both logos are facing the same direction and line up the posts in the socket with the holes in the Thermicon Tip. > Gently push into place.
REMOVING the Thermicon Tip > Grasp the Tip by both sides. > Gently pull the Tip out of the socket. When to REPLACE the Thermicon Tip > If the light turns red. > When the Tip icon on the status screen blinks red. > If it is no longer working efficiently. > If the wire is damaged in any way. Notes: > Make sure the Thermicon Tip is placed properly into the socket before treatment. > Never use a Thermicon Tip if the wire is bent or torn. How to no!no!
B C Turn no!no! On/Off [FIGURE B] > Press the On/Off Button down until the Status Screen lights up. NOTE: If the red light appears, go to About the Blue and Red Light section for further instructions.
Adjust the Treatment Level [FIGURE C] There are 3 Treatment Levels to customize the treatment for individual comfort. How to no!no! LOW MEDIUM HIGH Dynamic Speed Control The ULTRA s Dynamic Speed Control feature customizes each of the 3 Treatment Levels according to your gliding speed. Default Treatment Level When you use no!no! for the first time, the default Treatment Level is Low. When you turn the device on again, it will display the Treatment Level last used. Changing the Treatment Level Select the level by pressing the button under the Status Screen [FIGURE C] until the desired Treatment Level appears.
Getting Comfortable with Treatment Levels > Test a small section of your skin with the Low Treatment Level when starting to treat a new area for the first time. > Adjust the level after that, and if you can tolerate it, raise the Treatment Level to the highest level for optimal results.
Important Notes about Treatment Levels: > Should any Discomfort appear at any time STOP immediately, lower the Treatment Level and try again or move to a new area. > When treating facial hair, please see the Treating Facial Hair section. How to no!no!
D Gliding no!no! Glide no!no! at approximately a 90 angle with the Roller flat against your skin and the Status Screen facing in the direction you are treating. [FIGURE D]
Important Notes about Gliding: > Glide one way only, in the direction of the Status Screen. Do not go back and forth. > It is best to glide towards your body against the grain of the hair growth. However, if it is more comfortable you may glide in other directions, but always in the direction of the status screen. > Use a STEADY, SMOOTH and EVEN motion. If you move too slowly, the device will not activate; if you move too fast, you will not achieve optimal results. > When gliding at the proper speed the blue light will be steady. A blinking or flickering blue light indicates that you may be moving too slowly. Once your movement has been adjusted, the blue light will remain steady. > Do not press down too hard on your skin. > You may need to go over an area more than once; 4-6 passes may be enough. If the skin is not uncomfortably warm, you may continue. If there is still hair left after buffing and your skin is too warm, wait a few minutes to return to the area. Try to remove all of the hair. > Buff after each treatment to remove treated hair left behind. How to no!no!
Glide no!no! on Rounded Areas > Make sure you practice on smooth even skin like your legs or arms before moving to the face, knees, underarms or bikini line. > Go slowly and allow no!no! to follow the natural curve of the body. NOTE: The face and bikini line may be extra-sensitive to temperature. If it becomes uncomfortably warm during treatment, lower the Treatment Level or work on a different area, and return later. DO NOT use no!no! on the nipple or genital area, on or around the eye area or the eyebrows.
About the Blue and Red Light E The Blue Light under the Thermicon Tip will guide you throughout your treatment. It is visible only when you are gliding no!no! at the proper speed. [FIGURE E] How to no!no! The Red Light appears only when the Thermicon Tip is improperly installed, damaged or depleted. [FIGURE F] F BLUE LIGHT RED LIGHT WHAT IT MEANS ON AND STEADY OFF Correct Gliding Speed OFF ON No Thermicon Tip in Socket OFF ON Depleted Thermicon Tip OFF ON Damaged Thermicon Tip FLICKERING OFF Incorrect Gliding Speed OFF OFF Slow or No Movement
Treating Facial Hair [FIGURE G] > TEST no!no! on a small, discreet area of the face on the lowest Treatment Level to see how your skin reacts. > To treat the upper lip area, start under the nose and work your way outwards. > When treating the chin, jawline or sideburns, start just below the base of the chin or jawline and glide no!no! upwards following the curve of your face. > If you need to, pull your skin tight and/or purse your lips inward to help create a smooth, straight surface. > If there is any discomfort, STOP. > DO NOT allow your lips to come in contact with the thermodynamic wire. > DO NOT go over one area excessively. NOTE: The face and bikini line may be extra-sensitive to temperature. If it becomes uncomfortably warm during treatment, lower the Treatment Level or work on a different area, and return later. Go to www.howtonono.com for helpful videos on how to maneuver no!no! on the face.
How to no!no! G
H After Every Treatment: Buff Buffing exfoliates, removes treated hair and leaves your skin feeling smooth. Without buffing, treated hair remains on the skin leaving a prickly feeling. Hold the Buffer > Firmly rub the Buffer in a circular and/or back and forth motion over the treated area. [FIGURE H] When to Replace the Buffer > When the pad feels smooth. > When it is no longer buffing effectively.
How to no!no! I J Taking Care of Your no!no! NOTE: Do not use any liquid to clean the device, Thermicon Tips or Rollers. Keep the Thermicon Tips and Rollers clean to lower the risk of malfunction and prolong the life of the Tips. 1. Turn off your no!no!. 2. Remove the Thermicon Tip. 3. Gently brush the inside of the Tips clean. [FIGURE I] 4. Brush debris out and away from the socket and roller. [FIGURE J] I f any hair or debris falls into the socket, this may cause no!no! to malfunction. Brush any particles out of the socket before beginning a treatment.