Clips 06-5066 Place poster on a flat surface. Snap the Holder open and insert poster (top and bottom). To close, snap the Holder shut. Fig. 1 Note: It is easier to open and close the way down the holder. Insert Clips into slot on backside of the top Holder only. (You should hear a "SNAP" when the clips are inserted properly). Fig. 2 Note: For best results, place the clips 1/3 of the way in from each end on the top Holder. Suspend poster. Please save and reuse the Holder and Clips for future projects.
Clip 1UP-5066 Place poster on a flat surface. Snap the Holder (top and bottom) open so hinge is turned up as far as possible. Insert graphic completely into holder until edge of graphic meets top of holder. To close, snap the Holder shut. Fig. 1 Note: It is easier to open and close the way down the holder. With large or curling graphics, it may be easier to insert graphic at one end and slide into holder from one end to another. Insert OneUp Clips into slot on the backside of the top only. (You should hear a SNAP" when the clips are inserted properly). Fig. 2 Note: For best results, place the clip in the center of the top Holder. Fig. 3 Suspend poster. Please save and reuse the Holder and the OneUp Clip for future projects. Figure 3
Clip for Pegboard Clips for Pegboard Instructions for Hanging Place poster on a flat surface. Snap the Holder open and insert poster (top and bottom). To close, snap the Holder shut. Fig. 1 Note: It is easier to open and close the way down the holder. Insert the Clips into the holes in the pegboard. For best results, place the Clips in holes separated by a difference equal to half of the length of Holder. ( i.e. If holder is 12 place clips 6 apart). Fig. 2 Push onto clips, you will hear a SNAP. Fig. 3 Please save and reuse the Holder and Clips for future projects. Figure 3
Clip For Slatwall Clips for Slatwall Place poster on a flat surface. Snap the Holder open and insert poster (top and bottom). To close, snap the Holder shut. Fig. 1 Note: It is easier to open and close the way down the holder. Insert the Clip for Slatwall into slot on the back side of the top Holder only. (You should hear a SNAP when the clip is inserted properly). Fig. 2 Tilt holder and clip at a slight angle and slip the Clip for Slatwall hooks into the groove in the slatwall. Fig. 3 Please save and reuse the Holder and the Clip for Slatwall for future projects. Figure 3
# Clips 06-5066 Suction Cups with Hooks 06-SC150H Place poster on a flat surface. Snap the Holder (top and bottom) open so hinge is turned up as far as possible. Insert graphic completely into holder until edge of graphic meets top of holder. To close, snap the Holder shut. Fig. 1 Note: It is easier to open and close the way down the holder. With large or curling graphics, it may be easier to insert graphic at one end and slide into holder from one end to another. Note: For OneUp applications, the Holder is conveniently marked in the center. Find the mark and insert the OneUp Clip into slot on backside of the top only. (You should hear a SNAP when the clips are inserted properly). Fig. 2 Place the hooks of the suction cups through the holes in the Clips and press the Suction Cups firmly and evenly onto a clean window surface. Please save and reuse the Holder and Clips for future projects.
Window Mounts 20-0038 Instructions for Hanging Place poster on a flat surface. Snap the (top and bottom) open so hinge is turned up as far as possible. Insert graphic completely into holder until edge of graphic meets top of holder. To close, snap the shut. Fig. 1 Note: It is easier to open and close the by starting at one end and working your way down the holder. With large or curling graphics, it may be easier to insert graphic at one end and slide into holder from one end to another. Attach the Window Mounts to the. You should hear a Snap when the clip is properly seated.fig. 2 Note: For best results, place the suction cup clips 1/3 of the way in from each end on the top holder. Prepare the window and suction cups by making sure they are clean and free of dust and dirt. Press the suction cups firmly to the window. Important Note: For best performance when first applied and occasionally thereafter, press the middle of the cup (on the cap) to burp