FILASYSTEM The complete catalogue of Fila treatments. TREATMENT CYCLES TREATMENT STAGES WHAT TO DO IF Fila has always cared for all your s in stone, porcelain, terracotta and wood, at every stage of treatment: from washing to protection and maintenance. www.filachim.com filasolutions.com 1
CONTENTS Introduction 4 INTRODUCTION THE FILA SYSTEM: A WINNING STRATEGY TO ENHANCE MATERIALS Recommended by the world s top floor and wall coverings manufacturers, Fila solutions are more than just products. They deliver a complete treatment that stage after stage adds value to s, respecting their natural characteristics. From pre-treatment to maintenance, the Fila System guarantees long-lasting results. Treatment stages Pre-treatment 5 Washing after laying 6 Protection 8 Finishing 10 Maintenance 12 14 Stone 16 Agglomerates 0 Porcelain 4 Terracotta 8 Wood 45 Concrete 45 Resin, Rubber and Pvc Laminate Flooring Linoleum 46 Glossary CLEANING Cleaning is of primary importance to enhance the beauty of s and is divided into two stages: - washing after laying - maintenance (ordinary and extraordinary) Protecting materials from stains and humidity and at the same time achieving the desired look is a fundamental process that takes three stages: - pre-treatment - basic protection (below referred to as protection to simplify matters) - finishing protection (below referred to as finishing ) The following s go into each individual treatment stage in detail, giving all the information necessary to ensure a long life for your floors and wall coverings. Treatment cycles What to do if 2 48 FILA is the only company in the world recommended by over 200 TOP BRANDS of materials for floors and wall coverings
TREATMENT STAGES 0Pre-treatment 1 Washing after laying 0PRE-TREATMENT ADVANTAGES OF PRE-TREATMENT it protects s from grout residues it makes grouting easier it makes cleaning after laying simple it speeds up drying after initial washing and therefore also the subsequent treatment stages. PLEASE NOTE: This is not an obligatory stage, but it is recommended when the material to be grouted is very absorbent, like for example, terracotta and more porous natural stone. 2 Protection Finishing FILAPRW200 PRE-GROUTING PROTECTOR FILAPRW200 is the new water-repellent protector from Fila devised to protect floors between laying and grouting. It is effective against dirt produced when laying and makes grouting and cleaning easier without altering the material s appearance. Ideal for absorbent materials such as quarry tiles, natural and manufactured stone, agglomerates and terracotta. 4Maintenance after washing after washing after washing after washing Untreated Advice from the expert: when to pre-treat Treated with FILAPRW200 Untreated Material laid with adhesive should be pre-treated at least one day prior to grouting Treated with FILAPRW200 Anti-stain testing carried out on Vicenza stone and terracotta. The untreated section absorbed the cement deep down, and made washing after laying difficult. The treated part did not absorb the cement, which was easy to remove with a specific detergent. 4 5
1ING ADVANTAGES OF ING Advice from the expert: be careful with acid!,, PERFECT CLEANING, and ensure completely trouble-free cleaning after laying: They respect the s to be cleaned They do not erode metal or aluminium parts (handles, hoods, door and window frames ) They do not emit fumes that are harmful to the operator or the environment it makes the subsequent stages of protection and maintenance easier it removes residues of cement, adhesive and various kinds of dirt it stops these substances from adhering to the, which would make subsequent protection treatment ineffective. Given that 90% of washing after laying entails the use of acid products, it is a good idea to: Avoid acids that are too aggressive, which risk harming s; Choose buffered acids, which do not release harmful fumes for the operator; Choose acids that do not harm other fittings (edges in aluminium, hoods, door and window frames ); Left: an untreated terracotta floor after laying. Right: results after using are obvious. Choose products that not only remove encrusted dirt but also clean and therefore avoid having to repeat the procedure with other products If all instructions are followed, cleaning after laying will be a very simple operation and above all will guarantee a brilliant future for your s. Tumbled marble floor before cleaning. washing with : the is completely clean. THE RIGHT PRODUCT FOR EVERY SURFACE In the Fila range you will find the ideal product for correct effective cleaning after laying MATERIAL TYPE OF PRODUCT FILA PRODUCT A metal edging dipped in hydrochloric acid; the aggressive effect of the acid is obvious. A metal edging dipped in, remains unaltered. Left: the floor at Catullo Airport in Verona before cleaning. Right: the same floor after washing with after laying. Terracotta Acid Porcelain, ceramic tiles Acid Metallic porcelain tiles Neutral Glass mosaic, porcelain tiles and glazed ceramic tiles grouted with epoxy grout Marble, granite, travertine, polished agglomerates Alkaline Neutral FILACR10 Unpolished acid-resistant stone Acid Resin, marble resin, quartz resin Neutral Manufactured stone, marble chip tiles Alkaline ph 0 Acid (dil. 10%) ph 1,5 ph scale FILAVIA BAGNO ph 2,2 Acid detergents: for removing inorganic dirt, like for example residues of whitewash, limescale residues, rust, concrete, plaster residues, wall paint and building dirt in general. (dil. 10%) ph 7 Neutral ph 7 Neutral detergents: for daily cleaning, they remove various kinds of dirt while totally respecting s, even the most delicate. FUGANET ph 12,4 ph 12,5 FILACR10 ph 12,7 Alkaline detergents: for removing organic dirt, normal kitchen and daily dirt. Including grease, oil, tomato, Coca Cola, wine, beer etc. ph 14 Alkaline 6 7
2 Having carefully washed the material after laying, you can proceed with protecting it. ADVANTAGES OF It prevents absorption of water and oil stains; It makes maintenance simpler; It prolongs the life of materials. THIS PROCEDURE IS PARTICULARLY RECOMMENDED FOR: Absorbent materials, for example calcareous stone, polished marble, polished porcelain and terracotta s exposed to the risk of stains, for example floors and worktops in bathrooms, kitchens, showers, saunas and swimming pools: Exterior floors and s. Maintenance was carried out on both these buildings at the same time, but only the one on the right was protected with HYDROREP. In addition to protecting s from water, Fila water-repellent products prevent the formation of algae, efflorescence and damp stains. CHOOSE THE PRODUCT ACCORDING TO: The material to be treated; The location of the material (inside or out, floors or walls) The type of protection (water-repellent, stain-resistant) The desired effect (natural, colourenhancing, wet look) Advice from the expert: anti-graffiti treatment. How to protect your s from graffiti, smog and dust? For polished stone and polished porcelain use FILAMP90 stain protector or. For unpolished stone and fair-faced brick apply FILAW68 stain protector. For maintenance washing use FILANOPAINTSTAR detergent. WATER-REPELLENT OR STAIN-RESISTANT? WATER REPELLENT PROTECTORS are breathable because they penetrate right into the material s pores, repelling water and allowing air and water vapour to pass. are suitable for exterior s protect materials from the weather prevent the formation of moss, mould and efflorescence. THE RIGHT PRODUCT FOR EVERY SURFACE Polished ceramic and porcelain tiles Marble, granite, travertine, polished agglomerates Marble, granite, travertine, polished agglomerates Marble, granite, travertine, unpolished agglomerates Stain protection Stain protection Stain protection Stain protection Advice from the expert: choose according to available time. The speed of the protective treatment is often one of the requirements that affects choice. When the job must be completed quickly, it is better to opt for water-based products, which are more versatile and faster. If time permits, however, solvent-based products used, and can only be applied to perfectly dry s. Natural Colour-enhancing Natural Wet-look Natural stone Water-repellent Natural Natural stone Stain protection Colour-enhancing Natural stone Stain protection Natural Natural stone Stain protection Wet-look Polished natural stone and polished porcelain Unpolished natural stone terracotta Quarry tiles, brickwork and Terracotta Quarry tiles, brickwork and Terracotta STAIN PROTECTORS are breathable because they penetrate right into the material s pores, repelling water and allowing air and water vapour to pass. are suitable mainly for interior floors are useful in the case of exterior s that may stain, under parked cars for example also protect worktops, basins and doorsteps. give the material the desired effect: natural, colour-enhancing or wet-look. MATERIAL WHERE IT IS LAYED TYPE OF PRODUCT Anti-graffiti Anti-graffiti Water-repellent Stain protection WATER-BASED OR SOLVENT-BASED PROTECTORS? penetrate deeper are recommended for compact material that does not absorb well Natural Natural Natural Natural Terracotta Stain protection Wet-look Concrete Dirt-repellent Natural WATER BASED have low environmental impact are odourless applied even when there is residual moisture are better in the case of more porous, highly absorbent materials. FILAMP90 (solvent based) (water based) FILASTONE PLUS (solvent based) FILAMP90 (solvent based) (water based) FILAPT10 (water based) HYDROREP (solvent based) or HYDROREP ECO (water based) FILASTONEPLUS (solvent based) FILAFOB (solvent based) or FILAW68 (water based) FILAWET (solvent based) FILAPT10 (water based) FILAMP90 (solvent based) (water based) FILAW68 (water based) HYDROREP ECO (water based) FILAFOB (solvent based) or FILAW68 (water based) FILAPT10 (water based) FILABETON (water based) Water-repellent protectors prevent water from penetrating, creating the so-called drop effect clearly visible in the photo. 8 9
WAXES FOR 4 DIFFERENT S FILA PRODUCT FILA PRODUCT FILAMATT 9natural-effect wax FILALONGLIFE 9self-polishing high-gloss wax protection, we recommend you apply a finishing product, generally a wax. ADVANTAGES OF It nourishes the floor It protects from wear, caused by traffic or moving furniture It makes subsequent maintenance easier It allows the desired appearance to be obtained, from shiny to matt FILASATIN 9satin-effect wax FILACLASSIC 9buffable emulsion with typical wax effect Advice from the expert: wash&wax Application of a wax will make the look more nourished and brilliant. For on-going optimum protection, we recommend occasionally to apply a solution of diluted wax after washing with. Use FILASATIN, FILACLASSIC or FILAMATT (depending on the effect desired), diluting 2 or glasses in 5 litres of water. Advice from the expert: when to use and when not to use wax Finishes should only be carried out on interior floors, preferably not in damp rooms or where there is stagnant water (bathrooms, showers). For polished finishes, the wax used instead of waterproofing or during maintenance Finishing waxes should not be applied to porcelain or ceramic tiles 10 11
4 EXTRA Certain situations call for extraordinary maintenance. For example: SURFACES The treatment on your floor is very old, damaged or ineffective When the has lost its original beauty due to incorrect maintenance, the time has come to remove old treatments or old layers of wax and replace them. 1 2 Maintenance is nothing more than regular cleaning of the home. It removes dirt, eliminates footprints and reinforces the protective layer. A simple job in most cases, which takes very little time thanks to Fila detergents. STAIN REMOVAL If your is stained, Fila makes removing these stains easy. All you need to do is choose the right product for each kind of material, then and follow the instructions on the label and in this table. THE RIGHT PRODUCT FOR EVERY SURFACE Concentrated neutral detergent for the of every Advice from the expert: a few simple tips for better cleaning. 4 FILABRIO FILAVIA BAGNO FILANODROPS Universal spray detergent ofr every kind of wall claddings, ceramic tiles, plastic laminates, glazed s, stainless steel, glasses and mirrors Limescale removing spray detergent. It cleans all bathroom s (porcelain tiles, glass, stainless steel) Water mark repellent protective detergent. Prevents traces and streaks of limescale 1 Do not use alcohol or ammonia. Alcohol and ammonia harm s, treatments and finishing waxes, altering their natural beauty. Never use them, even on stains. These removed with Fila products. THE RIGHT PRODUCT FOR EVERY SURFACE TYPE OF STAIN Oil or grease PORCELAIN AND CERAMICS NATURAL STONE TERRACOTTA FILANOSPOT or FILASOLV FILANOSPOT or FILASOLV FILAREFRESH Protective detergent for tops. Cleans the s and reinforces the anti-stain protection of marble, granite and all treated natural stone Coloured stains (coffee, wine, soft drinks, hair dye, ink, felt pens, nicotine, fruit juices) or FILASR95 or FILASR95 or FILASR95 FUGANET Deep-down cleaner for grouts in ceramic tile floors and walls. 2 It is better to use warm water. Fila cleaning products give optimum results, but they become unbeatable with the addition of some warm water. Diluting the detergents actually increases their effectiveness. Remember this and you will achieve surprising results. Acid aggression (wine, lemon, anti-limescale ) Paint, graffiti Rust, sulphate and marks left by metals - or FILANOPAINT STAR FILANO RUST or * FILAMARBLE RESTORER (small s) FILAKRISTALL PLUS (large s) or FILANOPAINT STAR FILANO RUST or * - or FILANOPAINT STAR FILANO RUST or * No steam, thank you. Fila advises against using steam machines on all wooden floors and on waxed floors. Fila products allow you to clean just as quickly, but much more satisfactorily and without harming the materials. Concrete, saltpetre, limescale * * Candle wax, tar Silicone, resin, glue, candle wax, sticky tape, old labels and polyurethane foam. FILAZERO SIL or FILASOLV FILAZERO SIL or FILASOLV FILAZERO SIL or FILASOLV FILAZERO SIL FILAZERO SIL FILAZERO SIL Mould FILAACTIVE1 FILAACTIVE1 FILAACTIVE1 Fila has the ideal product also for ceramic tiles in the bathroom: the anti-limescale detergent FILAVIA BAGNO. When removing stains from wax-treated terracotta and natural stones, the wax must be reapplied afterwards. * do not use on shiny marble or in general on acid-sensitive materials (e.g. black slate). Carry out a preliminary test on ceramic tiles to check their resistance to the product. 12 1
Glossary Washing after laying: this cleans the of residues of concrete, glue and various kinds of dirt left after laying. Restoring sheen: treatment to restore the material s original sheen, to be carried out when the looks dull or damaged by acid stains. Restoring protection: process to renew the material s protection, to be carried out when the current treatment is very old, damaged or ineffective. A treatment cycle for each material. Restoring finishes: process to renew the protection of finishes, to be carried out when the material has old, worn, dirty or dull layers of wax. Removing graffiti, smog and dust: exterior s ruined by graffiti or blackened by smog and dust that need deep-down cleaning and restoration of the material s protection with specific products. Water-repellent protection: this protects the from water, watery stains (wine, coffee), wear by the weather and prevents the formation of moss, mould and efflorescence. Stain protection: a treatment for water-oil repellent protection. It combines protection against greasy and oily stains with water repellence. Anti-graffiti protection: to be carried out on exterior, vertical, absorbent s to avoid graffiti and spray paint stains, making cleaning easier. Dirt-repellent protection: protection recommended against dirt from through traffic. Particularly suitable for interior floors with rough-finish. Anti-dust protection/treatment: protective treatment recommended for interior vertical s to prevent dust settling, especially recommended for bricks or untreated stone. Treated material is easier to clean. Basic protection: impregnation of the material that gives the initial protection and allows subsequent treatments to be absorbed more evenly. Natural effect: natural effect is used to describe any treatment (protective or finish) that does not alter the material s natural appearance. Reviving/colour-enhancing: reviving/colour-enhancing is used to describe any treatment (protective or finish) that enhances the material s natural colour, giving it a pleasant appearance. Wet look: wet look is used to describe any treatment (protective) that revives the material to give a shiny effect. Satin effect: satin effect is used to describe any treatment (finish) that gives the a silky, slightly glossy sheen. Glossy effect: glossy effect is used to describe any treatment (finish) that gives the greater shine. Ordinary maintenance: ordinary cleaning of s to remove dirt, foot prints and strengthen the protective layer. Extraordinary maintenance: cleaning to remove stains and intense dirt that is difficult to remove with simple ordinary maintenance. Warning: Coverages are indicative, may vary depending on absorption of the materials, on treatment stage (washing after laying or restoring) and refer to one coat. Do not apply finishing products like wax in damp rooms and where there is stagnant water (bathrooms and showers). The treatment cycle is complete when the. Warning: this means that the with care. You must wait at least 24 hours for optimum protection. Maintenance treatments given here have been elaborated to restore previous treatments using Fila products. When the original treatment is unknown, we recommend consulting a Fila expert. STONE Natural stone pag. 16 Low absorbency pag. 16 High absorbency pag. 20 Cobblestones, tumbled or sand-blasted marble pag. 22 Polished or brushed finish pag. 26 Manufactured stone pag. 27 AGGLOMERATES Unpolished agglomerates pag. 0 Polished agglomerates pag. 1 PORCELAIN Enamelled ceramic tiles pag. 4 Polished porcelain pag. 4 Lappato porcelain pag. 5 Textured porcelain pag. 6 Crackle-glaze ceramic tiles pag. 7 TERRACOTTA Terracotta pag. 8 Terracotta / unglazed quarry tiles pag. 41 Unglazed quarry tiles pag. 42 Terracotta brickwork pag. 4 WOOD Wax treatment pag. 45 CONCRETE Decorated concrete pag. 45 Concrete pag. 46 RESIN, RUBBER AND PVC LAMINATE FLOORING LINOLEUM pag. 46 GROUTING pag. 47 Before application, always read the instructions on the product label carefully. This information is the fruit of our most recent technical knowledge and backed by continuous research and laboratory testing. However, due to factors outside our control, the suggestions given must always be checked and tried out by the user. Fila assumes no responsibility for incorrect use of its products. 14 15
NATURAL STONES Low absorbency Matt or unpolished finish (Slate, Porphyry, Basaltine, Trachyte, Granite) SOLVENT-BASED PRODUCTS s s NATURAL STONES Low absorbency Matt or unpolished finish (Slate, Porphyry, Basaltine, Trachyte, Granite) WATER-BASED PRODUCTS s s The expert s advice: treatment of slates The expert s advice: treatment of slates For the washing after laying of slates, we recommend to check the resistance of the material to the acid detergent. As an alternative, use the neutral detergent (diluted 1:0). For the treatment of slates layed indoors, the protection stage in an optional. the initial wash, only apply 2 coats of your chosen finishing wax. Attention: for bathrooms and damp rooms do not apply wax. We recommend stain-protection (see treatment on 20). For the washing after laying of slates, we recommend to check the resistance of the material to the acid detergent. As an alternative, use the neutral detergent (diluted 1:0). For the treatment of slates layed indoors, the protection stage in an optional. the initial wash, only apply 2 coats of your chosen finishing wax. Attention: for bathrooms and damp rooms do not apply wax. We recommend stain-protection (see treatment on 20). to be used only on acid-resistant stones FINISHES after 24 h FILAFOB COLOUR-ENHANCING after 8 h FILASTONE PLUS* 1 or 2 coats, 2nd coat after 8 h remove any excess during the application as mentioned in the product label FILAMATT 2 coats, 2nd coat SATIN FILASATIN 2 coats, 2nd coat SHINY FILALONGLIFE 2 coats, 2nd coat EXTRA diluted: 1:0 one coat of your chosen finishing wax to be used only on acid-resistant stones, working completely into the material before the product dries, remove any residue. COLOUR-ENHANCING (CHECK THE AVAILABILITY FOR YOUR MARKET), FILAPT10* o diluted 1:1 coverage: 10-20 m 2 /1L 2 coats, 2nd coat after h to remove FILAPT10 in the event of incorrect application or when deepdown cleaning is required, use the FILANOPAINT STAR cleaner. FILAMATT 2 coats, 2nd coat SATIN FILASATIN 2 coats, 2nd coat SHINY FILALONGLIFE 2 coats, 2nd coat EXTRA diluted: 1:0 one coat of your chosen finishing wax The expert s advice: pre-treat with FILAPRW200 To protect material from grouting dirt and facilitate cleaning after laying, pre-treat the with a coat of pre-grouting protector FILAPRW200 (; coverage: for terracotta 8/10 m 2, for stone 10/20 m 2 per liter) laying, pre-treat the with a coat of pre-grouting protector FILAPRW200 (; coverage: for terracotta 8/10 m 2, for stone FINISHES * for restoring tratment apply a single coat of the last protective product used. 16 17
NATURAL STONES Low absorbency Matt or unpolished finish (Slate, Porphyry, Basaltine, Trachyte, Granite) SOLVENT-BASED PRODUCTS s s NATURAL STONES Low absorbency Matt or unpolished finish (Slate, Porphyry, Basaltine, Trachyte, Granite) WATER-BASED PRODUCTS s s WATER REPELLENT, to be used only on acid-resistant stones coverage: 0 v/1l HYDROREP* 1 or 2 coats, 2nd coat after 24 h WATER REPELLENT 24 h HYDROREP COLOUR-ENHANCING, FILAFOB* EXTRA diluted: 1:10 coverage: 100 m 2 /1L to be used only on acid-resistant stones coverage: 0 v/1l, coverage: 10-20 m 2 /1L working completely into the material before the product dries, remove any residue. COLOUR-ENHANCING (CHECK THE AVAILABILITY FOR YOUR MARKET) WET LOOK, EXTRA diluted: 1:10 coverage: 100 m 2 /1L TO REMOVE GRAFFITI AND SMOG FILANOPAINT STAR coverage: 5 m 2 /1L after 8 h FILASTONE PLUS* 1 or 2 coats, 2nd coat after 8 h remove any excess during the application as mentioned in the product label. TO REMOVE GRAFFITI AND SMOG FILANOPAINT STAR coverage: 5 m 2 /1L FILAPT10* o diluted 1:1 coverage: 10-20 m 2 /1L 2 coats, 2nd coat after h to remove FILAPT10 in the event of incorrect application or when deepdown cleaning is required, use the FILANOPAINT STAR cleaner. WET LOOK WATER REPELLENT The expert s advice: pre-treat with FILAPRW200 To protect material from grouting dirt and facilitate cleaning after laying, pre-treat the with a coat of pre-grouting protector FILAPRW200 (; coverage: for terracotta 8/10 m 2, for stone 10/20 m 2 per liter), FILAWET* 1 or 2 coats, 2nd coat after 24 h, HYDROREP ECO coverage: 10-20 m 2 /1L one coat until to saturation to remove FILAWET in the event of incorrect application or when deep-down cleaning is required, use the FILANOPAINT STAR cleaner. laying, pre-treat the with a coat of pre-grouting protector FILAPRW200 (; coverage: for terracotta 8/10 m 2, for stone 18 19
NATURAL STONES High absorbency Matt or unpolished finish (Unpolished limestone, Vicenza stone, Lecce stone, Pietra Serena, Split-Finish Quartz) s s NATURAL STONES High absorbency Matt or unpolished finish (Unpolished limestone, Vicenza stone, Lecce stone, Pietra Serena, Split-Finish Quartz) s s diluted 1:0 AGAINST DIRT 4 h FILAW68 coverage: 10 m 2 /1L COLOUR ENHANCING, FILAPT10 o diluted 1:1 coverage: 10-20 m 2 /1L 2 coats, 2nd coat after h 1 h FILAJET to remove FILAPT10 in the event of incorrect application or when deepdown cleaning is required, use the FILANOPAINT STAR cleaner. FILAMATT 2 coats, 2nd coat SATIN FILASATIN 2 coats, 2nd coat SHINY FILACLASSIC 1 or 2 coats, 2nd coat SHINY EXTRA diluted: 1:0 one coat of your chosen finishing wax diluted 1:0 TO REMOVE GRAFFITI AND SMOG FILANOPAINT STAR coverage: 5 m 2 /1L FILAW68* coverage: 10 m 2 /1L 2 coats (no interval), WET LOOK, FILAPT10* o diluted 1:1 coverage: 10-20 m 2 /1L 2 coats, 2nd coat after h to remove FILAPT10 in the event of incorrect application or when deepdown cleaning is required, use the FILANOPAINT STAR cleaner. WATER REPELLENT, EXTRA diluted: 1:10 coverage: 100 m 2 /1L HYDROREP ECO coverage 15 m 2 /1L one coat until to saturation FILALONGLIFE 2 coats, 2nd coat laying, pre-treat the with a coat of pre-grouting protector FILAPRW200 (; coverage: for terracotta 8/10 m 2, for stone laying, pre-treat the with a coat of pre-grouting protector FILAPRW200 (; coverage: for terracotta 8/10 m 2, for stone 20 21
NATURAL STONES Cobblestones, tumbled or sand-blasted marble SOLVENT-BASED PRODUCTS s s NATURAL STONES Cobblestones, tumbled or sand-blasted marble WATER-BASED PRODUCTS s s to be used only on acid-resistant stones diluted 1:0 24 h FILAFOB COLOUR-ENHANCING after 8 h FILASTONE PLUS* 2 coats, 2nd coat after 8 h remove any excess during the application as mentioned in the product label. WET LOOK NATURAL FILAMATT 2 coats, 2nd coat SATIN FILASATIN 2 coats, 2nd coat EXTRA diluted: 1:0 one coat of your chosen finishing wax to be used only on acid-resistant stones diluted 1:0 4 h working completely into the material before the product dries, remove any residue. WET LOOK, FILAPT10* diluted 1:1 2 coats, 2nd coat after h to remove FILAWET in the event of incorrect application or when deep-down cleaning is required, use the FILANOPAINT STAR cleaner. NATURAL FILAMATT 2 coats, 2nd coat SATIN FILASATIN 2 coats, 2nd coat EXTRA diluted: 1:10 coverage: 100 m 2 /1L FINISHES, FILAWET* 2 coats, 2nd coat after 24 h to remove FILAWET in the event of incorrect application or when deep-down cleaning is required, use the FILANOPAINT STAR cleaner. SHINY FILALONGLIFE 2 coats, 2nd coat FINISHES SHINY FILALONGLIFE 2 coats, 2nd coat The expert s advice: pre-treat with FILAPRW200 To protect material from grouting dirt and facilitate cleaning after laying, pre-treat the with a coat of pre-grouting protector FILAPRW200 (; coverage: for terracotta 8/10 m 2, for stone laying, pre-treat the with a coat of pre-grouting protector FILAPRW200 (; coverage: for terracotta 8/10 m 2, for stone 22 2
NATURAL STONES Cobblestones, tumbled or sand-blasted marble SOLVENT-BASED PRODUCTS s s NATURAL STONES Cobblestones, tumbled or sand-blasted marble WATER-BASED PRODUCTS s s to be used only on acid-resistant stones TO REMOVE GRAFFITI AND SMOG WATER REPELLENT, HYDROREP WATER REPELLENT 24 h HYDROREP COLOUR-ENHANCING after 8 h FILASTONE PLUS* 1 or 2 coats, 2nd coat after 8 h remove any excess during the application as mentioned in the product label., FILAFOB* EXTRA diluted: 1:10 coverage: 100 m 2 /1L to be used only on acid-resistant stones TO REMOVE GRAFFITI AND SMOG, working completely into the material before the product dries, remove any residue. WET LOOK, FILAPT10* diluted 1:1 2 coats, 2nd coat after h to remove FILAWET in the event of incorrect application or when deep-down cleaning is required, use the FILANOPAINT STAR cleaner. EXTRA diluted: 1:10 coverage: 100 m 2 /1L FILANOPAINT STAR coverage: 5 m 2 /1L WET LOOK FILANOPAINT STAR coverage: 5 m 2 /1L WATER REPELLENT,, FILAWET* 2 coats, 2nd coat after 24 h to remove FILAWET in the event of incorrect application or when deep-down cleaning is required, use the FILANOPAINT STAR cleaner. HYDROREP ECO coverage 15 m 2 /1L one coat until to saturation laying, pre-treat the with a coat of pre-grouting protector FILAPRW200 (; coverage: for terracotta 8/10 m 2, for stone laying, pre-treat the with a coat of pre-grouting protector FILAPRW200 (; coverage: for terracotta 8/10 m 2, for stone 24 25
NATURAL STONES Polished or brushed finish (Marble, Travertine, Granite, Limestone) s s MANUFACTURED STONE s diluted 1:0 diluted 1:0 24 h, when the floor is dry, remove the excess using a cloth dipped in the product, then wipe with a dry cloth or absorbent paper FILAMP90 WATER BASED 4 h, when the floor is dry, remove the excess using a cloth dipped in the product, then, wipe with a dry cloth or absorbent paper COLOUR-ENHANCING after 8 h FILASTONE PLUS, remove any excess during the application as mentioned in the product label. SATIN 1 h Polishing FILASATIN coverage: 0-50 m 2 /1L SHINY 1 h Polishing FILACLASSIC coverage: 0-50 m 2 /1L SHINY (PROFESSIONAL USE) FILAKRISTALL PLUS 1 or more applications, do not use on non-calcareous stones such as granite, quartzite and sandstone. EXTRA diluted: 1:0 one coat of your chosen finishing wax FINISHES 24 h FILAFOB WATER BASED, working completely into the material before the product dries, remove any residue. FILAMATT 2 coats, 2nd coat SATIN FILASATIN 2 coats, 2nd coat EXTRA diluted: 1:0 THE GLOSS laying, pre-treat the with a coat of pre-grouting protector FILAPRW200 (; coverage: for terracotta 8/10 m 2, for stone 26 27
MANUFACTURED STONE s MANUFACTURED STONE s FINISHES laying, pre-treat the with a coat of pre-grouting protector FILAPRW200 (; coverage: for terracotta 8/10 m 2, for stone ANTI-DUST TREATMENT, the is ready FILAMATT 2 coats, 2nd coat FILABRIO ready to use, choose from:, choose from: WATER REPELLENT, HYDROREP* 2 coats, 2nd coat after 24 h WATER REPELLENT 24 h, EXTRA diluted: 1:10 coverage: 100 m 2 /1L HYDROREP FILAFOB* MANUFACTURED STONE s WATER BASED The expert s advice: pre-treat with FILAPRW200 To protect material from grouting dirt and facilitate cleaning after laying, pre-treat the with a coat of pre-grouting protector FILAPRW200 (; coverage: for terracotta 8/10 m 2, for stone 10/20 m 2 per liter) WATER REPELLENT, HYDROREP* 2 coats, 2nd coat after 24 h EXTRA, working completely into the material before the product dries, remove any residue. * for restoring tratment apply a single coat of the last protective product used. diluted: 1:10 coverage: 100 m 2 /1L laying, pre-treat the with a coat of pre-grouting protector FILAPRW200 (; coverage: for terracotta 8/10 m 2, for stone 28 29
UNPOLISHED AGGLOMERATES Rustic terrazzo, Marble concrete s s POLISHED AGGLOMERATES Venetian Terrazzo s TO REMOVE GRAFFITI AND SMOG FILANOPAINT STAR coverage: 5 m 2 /1L WATER REPELLENT, HYDROREP* coverage: 10 m 2 /1L 2 coats, 2nd coat after 24 h, FILAFOB* coverage: 10 m 2 /1L 2 coats, 2nd coat after 24 h WET LOOK, FILAWET* coverage: 10 m 2 /1L 2 or coats (24 h interval) to remove FILAWET in the event of incorrect application or when deep-down cleaning is required, use the FILANOPAINT STAR cleaner. WATER-BASED ALTERNATIVE WET LOOK FILAPT10* o diluted 1:1 coverage: 10-20 m 2 /1L 2 coats, 2nd coat after h FILAW68* coverage: 10 m 2 /1L 2 coats (no interval),, diluted 1:0 THE GLOSS 24 h, when the floor is dry, remove the excess using a cloth dipped in the product, then wipe with a dry cloth or absorbent paper FILAMP90 1 or 2 coats, 2nd coat after 24 h WATER BASED 4 h, when the floor is dry, remove the excess using a cloth dipped in the product, then wipe with a dry cloth or absorbent paper,, SHINY 1 h Polishing FILACLASSIC coverage: 0-50 m 2 /1L SHINY (PROFESSIONAL USE) FILAKRISTALL PLUS 1 or more applications, EXTRA diluted: 1:0 one coat of your chosen finishing wax EXTRA laying, pre-treat the with a coat of pre-grouting protector FILAPRW200 (; coverage: for terracotta 8/10 m 2, for stone diluted: 1:10 coverage: 100 m 2 /1L 0 1
POLISHED AGGLOMERATES Marble/Resin, Quartz/Granite/Resin s POLISHED AGGLOMERATES Terrazzo s diluted 1:10 24 h, when the floor is dry, remove the excess using a cloth dipped in the, product, then wipe with a dry cloth or absorbent paper FILAMP90 WATER BASED 4 h, when the floor is dry, remove the excess using a cloth dipped in the product, then wipe with a dry cloth or absorbent paper COLOUR-ENHANCING after 8 h FILASTONE PLUS coverage: 0-50 m 2 /1L, remove any excess during the application as mentioned in the product label. SHINY 1 h Polishing FILACLASSIC diluted 1:2 coverage: 60-80 m 2 /1L SHINY (PROFESSIONAL USE) FILAKRISTALL PLUS, to be used only on marble/ resin s FILAREFRESH ready to use EXTRA diluted: 1:10 coverage: 100 m 2 /1L one coat of your chosen finishing wax diluted 1:0 THE GLOSS 24 h, when the floor is dry, remove the excess using a cloth dipped in the product, then wipe with a dry cloth or absorbent paper FILAFOB WATER BASED 4 h, when the floor is dry, remove the excess using a cloth dipped in the product, then wipe with a dry cloth or absorbent paper,, SHINY 1 h Polishing FILACLASSIC coverage: 0-50 m 2 /1L SHINY (PROFESSIONAL USE) FILAKRISTALL PLUS 1 or more applications, EXTRA diluted: 1:0 one coat of your chosen finishing wax THE GLOSS diluted 1:10 coverage: 100 m 2 /1L 2
GLAZED CERAMIC TILES s s LAPPATO PORCELAIN s s (CONCRETE GROUT) (EPOXY GROUT) EXTRA, coverage: 40 m 2 /1L check the resistance of the material to the product before use, FILACR10 coverage: up to 10 m 2 /1L POLISHED PORCELAIN diluted: 1:5 s s (CONCRETE GROUT) coverage: 40 m 2 /1L check adhesion of the product on a small area before use (EPOXY GROUT) AGAINST DIRT after 8 h FILASTOP DIRT coverage: up to 70 m 2 /1L EXTRA (CONCRETE GROUT) coverage: 40 m 2 /1L (EPOXY GROUT) FILACR10 coverage: up to 10 m 2 /1L 24 h, when the floor is dry, remove the excess using a cloth dipped in the product, then wipe with a dry cloth or absorbent paper FILAMP90 WATER BASED 4 h, when the floor is dry, remove the excess using a cloth dipped in the product, then wipe with a dry cloth or absorbent paper,, FILABRIO ready to use EXTRA FILACR10 coverage: up to 10 m 2 /1L within 10 minutes from application, rub with asponge, cotton cloth or single-brush machine (white disc), to help the product penetrate and completely remove any residue. diluted: 1:5 diluted: 1:0 4 5
TEXTURED, NATURAL AND LAPPATO PORCELAIN TILES s s CRACKLE-GLAZE CERAMIC TILES s s (CONCRETE GROUT) coverage: 40 m 2 /1L (EPOXY GROUT) FILACR10 coverage: up to 10 m 2 /1L AGAINST DIRT after 8 h FILASTOP DIRT coverage: up to 70 m 2 /1L within 10 minutes from application, rub with asponge, cotton cloth or single-brush machine (white disc), to help the product penetrate and completely remove any residue. EXTRA diluted: 1:0 diluted 1:0 diluted 1:0 24 h, when the floor is dry, remove the excess using a cloth dipped in the product, then wipe with a dry cloth or absorbent paper FILAMP90 WATER BASED 4 h, when the floor is dry, remove the excess using a cloth dipped in the product, then wipe with a dry cloth or absorbent paper,, FILABRIO ready to use EXTRA diluted: 1:0 6 7
TERRACOTTA treatment with WATER-BASED PRODUCTS s TERRACOTTA treatment with SOLVENT-BASED PRODUCTS s after 7-15 days NATURAL AGAINST STAINS 4 h NATURAL NATURAL FILAW68 coverage: 7-20 m 2 /1L FILAMATT SATIN after 7-15 days ANTI STAIN 24 h FILAMATT SATIN WET LOOK EXTRA FILAFOB coverage: 5-20 m 2 /1L EXTRA, FILAPT10 coverage: 7-20 m 2 /1L 2 coats, 2nd coat after h to remove FILAPT10 in the event of incorrect application or when deepdown cleaning is required, use the FILANOPAINT STAR cleaner. FILASATIN SHINY diluted: 1:0, apply one coat of your chosen finishing wax COLOUR ENHANCING 8 h Polishing FILANATURWAX* 2 coats, 2nd coat after 8 h after FILASATIN SHINY diluted: 1:0, apply one coat of your chosen finishing wax FILACLASSIC SHINY STRONGER FOR SOLID WAXES FILACLASSIC SHINY FILALONGLIFE FILASOLV coverage: 5 m 2 /1L FILAMAX diluted from 1:1 to 1: 5 coverage: 5-20 m 2 /1L FILALONGLIFE laying, pre-treat the with a coat of pre-grouting protector FILAPRW200 (; coverage: for terracotta 8/10 m 2, for stone for manual intervention for professional intervention with single brush machine * choose FILANATURWAX in the desired colour. For maintenance treatment apply just of product. The expert s advice: pre-treat with FILAPRW200 To protect material from grouting dirt and facilitate cleaning after laying, pre-treat the with a coat of pre-grouting protector FILAPRW200 (; coverage: for terracotta 8/10 m 2, for stone 10/20 m 2 per liter) 8 9
TERRACOTTA treatment with WATER-BASED PRODUCTS s TERRACOTTA / UNGLAZED QUARRY TILES treatment with SOLVENT-BASED PRODUCTS s after 7-15 days, after 7-15 days STRONGER after 7-15 days FILAPHZERO FILAW68* coverage: 7-20 m 2 /1L 2 coats (no interval) WET LOOK, FILAPT10* coverage: 7-20 m 2 /1L 2 coats, 2nd coat after h to remove FILAPT10 in the event of incorrect application or when deepdown cleaning is required, use the FILANOPAINT STAR cleaner. EXTRA diluted: 1:10 coverage: 100 m 2 /1L STRONGER after 7-15 days FILAPHZERO, FILAFOB* coverage: 5-20 m 2 /1L EXTRA diluted: 1:10 coverage: 100 m 2 /1L WATER REPELLENT TO REMOVE GRAFFITI AND SMOG, TO REMOVE GRAFFITI AND SMOG HYDROREP ECO coverage 15 m 2 /1L one coat until to saturation FILANOPAINT STAR coverage: 5 m 2 /1L FILANOPAINT STAR coverage: 5 m 2 /1L laying, pre-treat the with a coat of pre-grouting protector FILAPRW200 (; coverage: for terracotta 8/10 m 2, for stone laying, pre-treat the with a coat of pre-grouting protector FILAPRW200 (; coverage: for terracotta 8/10 m 2, for stone 40 41
UNGLAZED QUARRY TILES s TERRACOTTA BRICKWORK s, FILAMATT* 2 coats, 2nd coat SATIN, FILASATIN* 2 coats, 2nd coat SHINY, EXTRA diluted: 1:0, apply one coat of your chosen finishing wax FILAPHZERO coverage: 5 m 2 /1L FINISHES NATURAL the is ready FILAMATT* 2 coats, 2nd coat for greater water-oil repellence on wall coverings with high stain risk (e.g. kitchen walls) we suggest an under-coat of FILAW68) FILABRIO ready to use EXTRA diluted: 1:5 FILALONGLIFE* 2 coats, 2nd coat, apply one coat of wax laying, pre-treat the with a coat of pre-grouting protector FILAPRW200 (; coverage: for terracotta 8/10 m 2, for stone laying, pre-treat the with a coat of pre-grouting protector FILAPRW200 (; coverage: for terracotta 8/10 m 2, for stone 42 4
TERRACOTTA BRICKWORK s VARNISHED WOOD s AND GRAFFITI coverage: 5 m 2 /1L TO REMOVE SMOG, FILAW68* coverage: 7-10 m 2 /1L 2 coats (no interval) DECORATED CONCRETE Encaustic cement tiles s TO REMOVE GRAFFITI AND SMOG FILANOPAINT STAR coverage: 5 m 2 /1L WATER REPELLENT, HYDROREP ECO coverage 15 m 2 /1L one coat until to saturation EXTRA FILANOPAINT STAR coverage: 5 m 2 /1L AGAINST STAIN, choose from: FILAFOB coverage: 10 m 2 /1L WATER BASED SATIN FILASATIN 2 coats, 2nd coat SHINY EXTRA after 4 h diluted: 1:0 - laying, pre-treat the with a coat of pre-grouting protector FILAPRW200 (; coverage: for terracotta 8/10 m 2, for stone FINISHES working completely into the material before the product dries, remove any residue. FILACLASSIC 2 coats, 2nd coat, apply one coat of your chosen finishing wax 44 45
CONCRETE s GROUTING For protection of grout joints when no other protector has been used s s AGAINST DIRT, FILABETON coverage: 20-25 m 2 /1L 2 coats, 2nd coat after 4 h EXTRA diluted: 1:0 VERY DIRTY JOINTS * diluted 1:10 coverage: 60 m 2 /1L AGAINST STAIN FUGAPROOF coverage: 100 m 2 /1L TREATED JOINTS FUGANET ready to use * do not use on shiny marble or in general on acid-sensitive materials. Carry out a preliminary test on ceramic tiles to check their resistance to the product. RESIN FLOORS, RUBBER AND PVC LAMINATE FLOORING LINOLEUM s AGAINST DIRT EXTRA : diluted 1:0 FILALONGLIFE 2 coats, 2nd coat diluted: 1:0 46 47
What to do if Candlewax residues pag. 49 PROBLEM MATERIAL CATEGORY REFERENCE PRODUCTS ANSWER Coloured stains (ink, coffee, markers, soft drinks, hair dye, nicotine, fruit juices) pag. 49 Concrete residues and grout pag. 49 Dirty grouting pag. 49 Candle wax residues - Natural stone - Terracotta, quarry tiles and bricks - Porcelain and ceramic tiles - Wood FILASOLV, FILAZERO SIL Wax removed by applying FILASOLV and rubbing with a green abrasive sponge. Any residue should then be removed using kitchen towel. Surface residues can also be removed using FILAZERO SIL: apply the undiluted product, covering the entire stain. Leave for 20 minutes and then use the spatula provided in the kit. Collect any residue with a soft cloth or kitchen towel. In the event of interior floors treated with wax, restore the finish after cleaning. Dull stains (vinegar lemon, Coca Cola, wine, anti-limescale product) pag. 50 Flaking pag. 50 Greasy and oily stains pag. 50 Limescale (stubborn dirt or streaks) pag. 51 Coloured stains (ink, coffee, markers, soft drinks, hair dye, nicotine, fruit juices) Porcelain and ceramic tiles - Natural stone - Terracotta, quarry tiles and bricks Varnished wood FILASR95, FILASR95, Remove the stains with FILASR95. Pour the product directly onto the stain, leave it to work for about 15 minutes, then remove residues with a damp sponge and rinse with water. If necessary repeat. As an alternative, use undiluted leaving it to work until completely dry. Wash and rinse the. Remove the stains with FILASR95. Pour the product directly onto the stain, leave it to work for about 15 minutes, then remove residues with a damp sponge and rinse with water. If necessary repeat. As an alternative, use with a sponge. Rinse the to complete. Restore stain protection treatment with the most suitable product. Use diluted 1:200 and wipe the with a sponge or a clean dry cloth. Matt pag. 52 Mould pag. 52 Paint marks, graffiti pag. 52 Residues of epoxy grouting pag. 52 Rust pag. 5 Concrete residues and grout - Natural stone - Porcelain and ceramic tiles, acid detergent used on acidresistant unpolished stone. For sensitive materials, like marble, travertine and polished agglomerates, it is better to use neutral detergent. Salt efflorescences pag. 5 White alcohol, ammonia or bleach stains pag. 5 Terracotta, quarry tiles and bricks We recommend washing the with acid detergent for more stubborn encrusted grout. For dilution and application of both products, read the instructions on the label carefully. Residues of glue, chewing gum, adhesive tape, tree resin pag. 5 Residues of silicon and polyurethane foam pag. 5 Dirty grouting Porcelain and ceramic tiles, FUGANET, FUGAPROOF Floor grouting must be cleaned with, using a flat brush or an abrasive sponge. Rinse thoroughly to complete. For small s and wall coverings we recommend using FUGANET spray detergent. Spray the product on the from a distance of about 15-20 cm, rub with an abrasive sponge and then rinse. cleaning we recommend protecting grouting with FUGAPROOF stain protector. 48 49
What to do if Check out filasolutions.com to find the answer to any other questions you might have. PROBLEM MATERIAL CATEGORY REFERENCE PRODUCTS ANSWER PROBLEM MATERIAL CATEGORY REFERENCE PRODUCTS ANSWER Dirty grouting Natural stone Grouting of floors and wall coverings in natural stone must be cleaned with, using a flat brush or an abrasive sponge. Rinse thoroughly to complete. Restore stain protection treatment with the most suitable product. Greasy and oily stains Wood FILASOLV The stains removed with undiluted FILASOLV, rubbing with a green abrasive sponge and removing residues with kitchen paper. We recommend reapplying the finishing wax on interior floors after cleaning. Dull stains (vinegar lemon, Coca Cola, wine, anti-limescale product) Natural stone FILAMARBLE RESTORER, FILAKRISTALL PLUS Many substances such as vinegar, lemon, Coca Cola, wine, anti-limescale products... are slightly acidic and attack the sheen of marble and of polished natural stone, leaving a dull stain. To restore small s like bathroom and kitchen tops, window sills, etc., we recommend using the FILAMARBLE RESTORER kit. For larger s like floors, we recommend using FILAKRISTALL PLUS. Limescale (stubborn dirt or streaks) Porcelain and ceramic tiles, FILAVIA BAGNO, FILANO DROPS In the case of stubborn dirt, we recommend washing with the appropriate dilution of acid detergent and rinsing thoroughly after application. Please follow the instructions on the label carefully. Use FILAVIA BAGNO on marks or limescale residues (e.g. bathrooms, showers). To prevent limescale residues coming back, use FILANO DROPS for ordinary. Flaking - Natural stone - Terracotta, quarry tiles and bricks FILAMATT To prevent interior walls giving off dust, a naturaleffect wax like FILAMATT used, applying two coats directly with a paintbrush. Natural stone, Stubborn dirt: acid detergent used on acid-resistant unpolished stone. For sensitive materials, like marble, travertine and polished agglomerates, it is better to use neutral detergent. Greasy and oily stains - Terracotta, quarry tiles and bricks - Natural stone FILANOSPOT Clean the with FILANOSPOT by spraying it directly onto the oily stain. Leave to dry for a few minutes and then remove the white powder that has formed with a brush. Clean with a damp cloth. We recommend restoring the finish of wax-treated floors. Glass, mirrors FILAVIA BAGNO, FILANO DROPS We recommend using FILAVIA BAGNO on marks or limescale residues (e.g. bathrooms, showers). To prevent limescale residues coming back, use FILANO DROPS for ordinary maintenance. - Concrete and grouting Porcelain and ceramic tiles Clean the with -1:10 and rinse thoroughly. Terracotta, quarry tiles and bricks We recommend washing the with acid detergent for more stubborn encrusted grout. For dilution and application of both products please read the instructions on the label carefully. 50 51
What to do if Check out filasolutions.com to find the answer to any other questions you might have. PROBLEM MATERIAL CATEGORY REFERENCE PRODUCTS ANSWER PROBLEM MATERIAL CATEGORY REFERENCE PRODUCTS ANSWER Matt Mould Paint marks, graffiti Residues of epoxy grouting Natural stone Terracotta, quarry tiles and bricks - Wall paint and marble chip plaster - Terracotta, quarry tiles and bricks - Porcelain and ceramic tiles - Concrete and grouting - Natural stone - Porcelain and ceramic tiles - Natural stone - Concrete and plaster - Terracotta, quarry tiles and bricks - Porcelain and ceramic tiles - Glass mosaic FILAKRISTALL PLUS, FILACLASSIC, FORMULA MARMO, FILAREFRESH FILACLASSIC, FILAMATT, FILASATIN, FILALONGLIFE, FILANATURWAX FILAACTIVE1 FILANO PAINT STAR, FILACR10 For floors and large s, shine restored using FILAKRISTALL PLUS. Spread the product all over the. Once dry, it polished with a single-brush machine or machine polisher fitted with special wire wool discs. As an alternative, it is possible to use FILACLASSIC wax, either undiluted or diluted in water, depending on how worn the treatment is. To restore sheen to tops in marble or already treated natural stone, apply FORMULA MARMO polish with a cloth. For ordinary maintenance we recommend cleaning the with FILAREFRESH to reinforce stain protection. To restore the finishing with a liquid wax, choosing from FILACLASSIC, FILAMATT, FILASATIN, FILALONGLIFE according to the desired appearance. For traditional treatment with paste wax, apply a coat of FILANATURWAX before the finishing wax. Spray FILAACTIVE1 directly onto the to be cleaned. Leave for about 15 minutes. Rinse with a wet sponge. Apply undiluted FILANOPAINT STAR directly onto the, leaving for at least 5 minutes. Use a sponge or cloth and rinse. As an alternative, use following the same instructions. Complete or restore stain protection treatment with the most suitable product. We recommend using undiluted FILACR10 detergent for epoxy residues, leaving it on the for at least 0 minutes. Then rub with an abrasive sponge or spatula. Rinse the thoroughly. Repeat the procedure if necessary. Rust Salt efflorescences White alcohol, ammonia or bleach stains Residues of glue, chewing gum, adhesive tape and tree resin Residues of silicon and polyurethane foam - Natural stone - Stoneware and ceramics - Terracotta, quarry tiles and brick - Cement and tile joints Terracotta, quarry tiles and bricks - Terracotta, quarry tiles and bricks - Natural stone - Terracotta, quarry tiles and bricks - Porcelain and ceramic tiles - Natural stone FILANO RUST,, FILAPHZERO Apply FILANO RUST, completely covering the stain. Leave to act for 15 minutes then remove any product residues and rinse. Alternatively (and in the event of very large stains), used. Dampen the area to be cleaned with water, then apply. Rub with a green abrasive sponge. Rinse thoroughly when finished. Avoid use on marble or limestone with fine polished s. To remove salt efflorescences, wash the with or FILAPHZERO and then rinse. Alcohol and ammonia, or products containing these substances whiten waxes. In this situation use to strip the wax from the entire tile. Rinse with water and apply a coat of wax. FILASOLV,, FILAZERO SIL Apply FILASOLV (undiluted) or (diluted approx. 1: on s previously dampened with water), and rub energetically with an abrasive green sponge. Rinse thoroughly when finished. Surface residues can also be removed using FILAZERO SIL: apply the undiluted product, covering the entire stain. Leave for 20 minutes and then use the spatula provided in the kit. Collect any residue with a soft cloth or kitchen towel. In the event of treated interior floors, the protective treatment should be restored after cleaning. Wood FILASOLV, FILAZERO SIL Apply FILASOLV (undiluted) and rub with a sponge. Remove any residues when finished. Surface residues can also be removed using FILAZERO SIL: apply the undiluted product, covering the entire stain. Leave for 20 minutes and then use the spatula provided in the kit. Collect any residue with a soft cloth or kitchen towel. In the event of interior floors, any protective treatment should be restored after cleaning. - Porcelain and ceramic tiles - Natural stone - Glass - Metal, steel FILAZERO SIL Apply FILAZERO SIL (undiluted), covering the entire stain. Leave for 20 minutes and then use the spatula provided in the kit. Collect any residue with a soft cloth or kitchen towel. In the event of interior floors, any protective treatment should be restored after cleaning. 52 5
All Fila solutions directly in your hands. NOTES The smartphone and tablet app designed for building site professionals, retailers and all those wanting to look after their home, is now available in 6 languages: Italian, UK English, US English, German, Spanish and French. This application puts the best solution for any need on different materials right at the fingertips of an increasing number of people: from care, to washing after laying and protective treatment, to stain removal. TREATMENT SYSTEMS identifies the ideal treatment for any (natural stone, porcelain tiles, terracotta, wood and other materials). TREATMENT STAGES identifies the suitable solutions for each stage during the treatment (pre-treatment, washing after laying, protection, finishing and maintenance). WHAT TO DO IF FAQs about common problems (stains, mould, application issues, etc.). PRODUCT CALCULATOR an additional function that will be popular with future users. It easily works out the amount of product needed for each treatment. FILA PRODUCT CATALOGUE contains detailed information about products, certification, treatment videos and technical information sheets. FIND YOUR NEAREST SALES POINT with an option for directions to your nearest store. TECHNICAL ASSISTANCE this puts the user in direct contact with Fila technical assistance, able to give a prompt reply to any advice required. Available for all smartphones and tablets (both Apple and Android) and completely free of charge.