GEBS0042-01 April 2015 PART NUMBER CROSS REFERENCE GUIDE BY CATERPILLAR BINC NUMBERS TO CATERPILLAR NUMBERS SAFETY.CAT.COM
2
Product and Dealer Information Note: For product identification plate locations, see the section Product Identification Information in the Operation and Maintenance Manual. Delivery Date: Product Informaton Model: Product Identification Number: Engine Serial Number: Transmission Serial Number: Generator Serial Number: Attachment Serial Numbers: Customer Equipment Number: Dealer Equipment Number: Dealer Information Name: Branch: Address: Dealer Contact Phone Number Hours Sales: Parts: Service: 3
Attachment Identification Caterpillar Work Tools products are identified with SE- RIAL NUMBERS, MODEL NUMBERS AND REFERENCE NUMBERS. These numbers are assigned to the product and completing components for the product (i.e. - lines groups, mounting brackets, etc. These numbers are shown on the SERIAL NUMBER plate. Caterpillar dealers use all these numbers to determine which components were assembled on your product at the factory. This permits accurate identification of replacement part numbers. Ordering Parts Quality replacement parts are available from Caterpillar Dealers throughout the world. Their parts inventories are up to date and include parts required to repair or rebuild your Caterpillar work Tools product.when ordering parts, you should specify the quantity, part number, and you should provide attachment reference number, part name, and the serial number, if in doubt about the part number, please provide your Caterpillar dealer with a complete description of the needed item. How To Use The Parts Book Caterpillar Work Tools parts books include illustrations of the groups or assemblies which make up the product. These illustrations show the components of the product. Abbreviations And Symbols O.D Outside Diameter I.D. Inside Diameter A Not serviced as a group B Use as required C Change from previous type D Order by the meter E Order by the centimeter F Not shown G Order by the inch M Metric Part N Note below Y Swparate illustration * Part available from Caterpillar Work Tools Ref No. The numbers shown in this column refer to the numbers shown within the illustration. To identify any item within the illustration, first determine its reference number, then refer to the same number in the Ref. No. column in the bill-of-materials for more information about the part Part Number These numbers identify the serviceable parts. Qty The quantities shown in this column indicate the total number of that item used in the group or assembly covered by the illustration. Part Name Information this column provides is the name of the part as well as additional information such as size, which further aids in the identification of the part. Indented Parts Names Within each illustration is a parts list identifying each serviceable part in the illustration. When a part name is indented in this list, it means that the serviceable item is a part of the serviceable item under which it is indented. NOTE: Continuing improvements and advancements of product design may cause changes to your attachment which may not be included in this publication. Each publication is reviewed and revised, as required, to update and include these changes in later editions. Whenever a question arises regarding your Caterpillar Work Tools product, or this publication, please consult your Caterpillar dealer for the most current information available. 4
5
000646 3B-4631 COTTER 000992 3B-5320 COTTER.375X 3.000 000993 179-1633 CLEVIS PIN.625X 3.500 001054 322-6629 PLATE-NOSE PIECE 001213 277-5555 DONUT 003699 322-6625 (918F) SHOE AS. 003708 171-4808 SHOE AS.-BASE 003725 171-4810 HOLDER ASSEMBLY-SHOE 003775 173-1172 SHOE UPRIGHT 003778 173-1173 SHOE HOLDER 008833 313-5579 PLATE-WEAR (MOD. 7T-3491 C.E.) 010114 336-4484 EDGE-CUTTING 010131 336-4483 EDGE-CUTTING 011911 322-6628 EDGE-CUTTING 16MM/600/12000 012331 285-4515 CE SBF P 1.00X10.00X158.50 012751 326-9824 EDGE-CUTTING 012845 151-1998 EDGE-CUTTING 012920 311-6826 EDGE-CUTTING 012924 142-7231 CE SBF P 1.00X 8.00X 94.75 012975 368-0504 EDGE-CUTTING 012985 329-7791 EDGE-CUTTING 012986 329-7790 EDGE-CUTTING 012987 329-7792 EDGE-CUTTING 013374 313-5574 PIN AS. 014793 217-9833 SELF ALIGNING BUSHING 015592 313-5577 END BIT-RH 015593 313-5578 END BIT-LH 015753 321-5053 PLATE-EAR 015769 285-4555 BEARING 016266 217-4562 CORNER RH 016267 217-4563 CORNER LH 016278 173-1190 EAR 016492 261-6405 PIN 150/946 016518 241-0717 HOOK ASSEMBLY-FLAT-BACK 016537 170-4900 TUBE 016538 170-4901 TUBE 016663 8S-6377 PIN-LOCK 016714 165-5761 CLAMP ASSEMBLY 016924 277-5539 CLAMP AS. 017878 171-1296 SHIM 018021 137-6639 CYLINDER GP-HYD 018031 187-0987 PLUG-NYLON 018035 172-8121 TUBE 018036 137-6638 SEAL KIT 018328 313-5575 PIN AS. 018393 277-5542 CLEVIS AS. 020143 231-3344 PIN ASSEMBLY 023128 2R-6806 06-ADAP-ST- -.375STTD-.375MJIC 023341 6V-0744 08-ARMORGUARD FOR.50HOSEXILG 023364 1P-4574 FLANGE-SPLIT (CODE 61-8) 6
023365 1P-4576 FLANGE-HALF 023366 1P-4577 FLANGE-HALF (-16) 023893 9S-8752 NUT-HEX NC GRADE 8.375 024521 277-5479 PIN 024685 8D-9088 06-ADAP-ST-L-.5STOR-.375MJIC 025016 105-8095 MOTOR (24 VOC) 025022 275-8463 KIT-SOLENOID 025137 3B-5301 COTTER 025244 AND 277-5546 331-9951 BOLT-DRILLED 027446 277-3788 BUSHING 028728 144-6883 (980G) HOOK AS-FLAT BACK 028742 224-8689 PLATE-BOSS(USE 224-8689 PRO-E) 028877 140-6630 (980G) HOOK ASSEMBLY-BLANK 029884 172-8333 TUBE 75/300/50 030822 313-5614 PIN 030824 313-5612 PIN 030825 313-5613 COLLAR-PLT(USE 313-5613 PRO-E) 031510 3B-4647 COTTER.375X 2.500 034242 277-5497 SPRING 035220 171-1297 BAR 125/500/450 035220 TOP 171-1298 BLOCK-PILLOW BLQ A 038779 285-4557 RING-SNAP 040234 172-8335 CHAIN *NP 041409 343-2112 HOOK *NP 041475 316-5196 HOOK 042188 263-0104 TUBE 50/288/112 042428 205-5810 HOOK 4" *NP 042430 188-1324 WEDGE POCKET 042709 166-0001 TUBE 150/500/228 042717 174-7501 PIN 100/175 042815 188-1322 HOOK ASSEMBLY 966G *NP 042822 188-1323 HOOK 042823 160-9718 BAR 100/450/2423 043116 163-8834 BOSS 043235 217-9834 SNAP RING 043300 278-8296 HOOK AS.-FLATBACK 043301 278-8295 (950) HOOK ASSEMBLY-BLANK 043349 174-7392 TUBE 044209 205-5812 HOOK ASSEMBLY 044334 105-8094 PUMP & BASE ASSEMBLY 045231 291-0933 TUBE (USE 291-0933 PRO-E) 045318 313-3326 TUBE (USE 313-3326 PRO-E) 045939 327-9701 SHAFT 047034 270-8044 EDGE-SUPPORT CENTER 047488 316-5195 HOOK AS. 048643 180-6397 TUBE 048648 301-1123 COLLAR-PLA(USE 301-1123 PRO-E) 048995 165-5759 TINE 275X700X6000/313 048996 184-6343 TINE 048997 164-4071 TINE 350X700X8400/313 7
048998 194-0435 TINE 350X700X9600/313 049121 301-1122 PIN (USE 301-1122 PRO-E) 049122 301-1121 PIN AS. (USE 301-1121 PRO-E) 049161 263-0097 TUBE 125/400/350 049162 263-0098 TUBE 125/400/350 049215 263-0108 PIN 049216 263-0107 PIN 049217 263-0106 PIN 050321 183-2161 PIN AS. 050336 209-6415 TUBE 050337 216-7207 BOSS 050447 291-0157 PLATE-WEAR 12MM/800/925 051237 298-4000 PIN AS. 051238 298-4001 PIN-SHAFT 275/950 051239 298-4002 PIN-COLLAR 051240 298-3996 PIN AS. (USE 298-3996 PRO-E) 051241 298-3997 PIN 250/775 051241 298-3997 PIN (USE 298-3997 PRO-E) 051242 291-0199 COLLAR-PLA(USE 291-0199 PRO-E) 051357 268-3323 TUBE (USE 268-3323 PRO-E) 051729 177-4516 CYINDER (MODIFIED 019513) 051801 171-4811 PLATE-SHOE SOLE 8" 052130 240-8309 PLATE-WEAR PAD 052849 327-9698 MOUNTING BOX AS. 053689 321-5037 EDGE-SUPPORT 054719 169-9654 BLOCK-PORT 054885 031-1358 12-ADAP-90.50NPTF-.75MJIC 056651 316-5033 DUST-CAP 056885 258-0441 HOSE ASSEMBLY 058994 2K-0564 NUT-LOCK 1/2-20 GD.8 058995 0S-1604 BOLT 1/2-20x2 1/2 059471 380-8361 PLATE-WEAR 059685 145-2443 TIP-WEAR 059926 1K-6870 LOCKNUT 3/4-10 THD 060788 8S-4055 CAT REUSABLE COUPLING.500 061407 3V-8851 HOSE ASSEMBLY 061473 146-8531 CRIMP COUPLING 061476 146-8533 CRIMP COUPLING 061477 180-6391 PIN 061488 183-2160 PIN AS. 062695 189-4475 TUBE-BOSS 88/500/300 062841 209-6414 TUBE-BOSS 063223 292-9410 WEAR-TIP 065252 345-0153 PLATE-WEAR PAD 066628 313-5584 EDGE-SUPPORT 067962 344-9340 HOSE AS. 068114 179-9286 PLATE-HOOK 068117 179-5752 BAR 068303 174-7596 VALVE-LOCKING 068426 277-5543 CABLE 8
068796 5G-1791 HOSE ASSEMBLY 069149/143306 225-7029 HOSE ASSEMBLY 069558 229-6011 HOSE ASSEMBLY 069559/070387 229-6006 HOSE ASSEMBLY 069574 254-1186 BAR (USE 254-1186 PRO-E) 069608 249-4539 HOSE ASSEMBLY 069869 8C-8513 PIN-SPRING 071703 6V-7688 NUT 071735 147-2432 NUT 10MM 071760 205-4847 BUFFER 072782 9S-0128 CAT REUSABLE COUPLING.500 072798 8T-3713 CRIMP COUPLING use 8T-3713 072801 5S-9593 CAT REUSABLE COUPLING.500 072802 5S-9616 CAT REUSABLE COUPLING.500 073964 263-0119 BUMPER-TECS PAK 074107 263-0112 SPACER 074109 263-0114 SHAFT 074414 7K-0702 HOSE ASSEMBLY 075404 177-2873 HOSE ASSEMBLY 075994 337-2864 EDGE-SUPPORT 075995 337-2861 EDGE-SUPPORT AS. 076047 337-2870 EDGE-SUPPORT 076392 1G-9959 CLAMP (HALF) 076828 343-5493 PLATE-PAD WEAR 63/500/600 077175 6V-4677 CAT REUSABLE COUPLING.750 077388 6V-4671 CAT REUSABLE COUPLING.750 077590 261-5561 BAR-STOP (USE 261-5571 PRO-E) 077592 261-5572 LINK ASSEMBLY 077593 261-5575 PIPE-SPACER SCH 40 100/50 077638 5S-9592 CAT REUSABLE COUPLING.500 077741 142-6007 PIN ASSEMBLY 077743 242-1506 PLATE-EAR (USE 242-1506 PRO-E) 077990 312-2222 TUBE-BOSS 077991 312-2223 TUBE-BOSS 078431 242-1488 PIN AS. 078432 166-7427 BAR-STOP 38/250/500 078467 7V-6089 CLAMP-HALF 078471 242-1504 SHAFT (USE 242-1504 PRO-E) 078542 160-9717 HOOK ASSEMBLY *NP HPL 078637 315-2734 SHAFT 078770/120-6336.00-147-1543 HOOK ASSEMBLY Q/C 4" *NP HPL 079136 329-7753 EDGE-SUPPORT 079653 309-7408 TUBE - OUTER (USE 242-1482) 079707 285-8975 LUG-LIFTING 079906 307-1985 HOSE AS. 080198 284-7722 VALVE-DUAL RELIEF 080614 281-1221 EDGE-SUPP 20MM/900/1813 081394 329-7789 PLATE-EAR (USE 329-7789 PRO-E) 082046 216-5449 CORNER-BRACE RH 082047 216-5450 CORNER-BRACE LH 9
082943 373-1869 EDGE-CUTTING 083316 4V-7174 CORNER-LH 083317 4V-7175 CORNER-RH 083318 5V-1783 CORNER-RH 083319 5V-1784 CORNER-LH 083320 4V-1544 CORNER-RH 083321 4V-1545 CORNER-LH 084500 230-7082 TRUNNION GP-BULLDOZER 084508 264-8253 PIN 175/525 084509 264-8254 BAR 38/100/400 084629 264-6729 EDGE SUPP (USE 264-6729 PRO-E) 084783 265-5496 PLATE-PAD 085640 264-3728 PRESSURE PLATE 085728 264-8251 PIN 400/1161 085729 264-8252 BAR-RETAINER 50/150/550 085929 194-0659 CE SBF P 1.75X12.00X150.00 086899 8T-4149 ELBOW-45 (DEG) -12 TO -16 087172 139-0428 CLAMP 087479 192-0287 PIN 325/1100 087834 317-3623 BLOCK 087847 349-5961 EDGE-SUPPORT (CENTER) 088115 172-6547 HOOK AS. *NP 088468 6V-8781 ADAPTER-TEE 088476 6V-9836 ADAPTER-TEE (ORFS) 088692 317-3620 EAR AS.-LH 089285 265-5480 EAR ASSEMBLY 089286 265-5495 PLATE-EAR 089444 265-5462 EDGE SUPPORT CENTER 089445 265-5463 EDGE SUPPORT WING 089457 265-5477 CUTTING EDGE-MODIFIED 089458 265-5478 EDGE-CUTTING 089459 265-5479 EDGE-CUTTING 089587 315-0251 PUMP (OILDYNE 12 VOLT) 093-7676 8T-4131 NUT (M20)(USE 8T-4131) 094023 121-8908 HOOK ASSEMBLY FLAT BACK HPL 094024 135-6323 HOOK ASSEMBLY-BLANK 938G/928G 094026 244-2854 HOOK ASSEMBLY-PROFILE (953)HPL 095204 244-2199 HOOK ASSEMBLY-PROFILE (963)HPL 097914 6V-9182 ADAPTER-ELBOW 90 DEG 098175 124-2028 COUPLING 90.38 JIC (LONG) 098195 141-7836 DOZER HARDWARE D10N 098636 242-1661 HOOK AS-PROFILE 9R0089/9R5989 098637 151-5336 HOOK AS-PROFILE 9R4488/9R5201 098990 252-8627 EDGE-SUPPORT CTR20MM/900/11270 098991 252-8628 EDGE-SUPP WING 20MM/900/6397 099156 190-2204 CHAIN MODIFICATION PN# 113728 099157 190-2205 PIN 099168 190-2432 PLATE-BLOCK 099171 190-2435 TUBE 75/450/300 099532 190-2214 PLATE-LOCK 10
100085 190-2208 HOOK 1001326 LAVAL 288-6082 TUBE 28/163/335 102902 272-2749 EDGE-SUPPORT WING 103011 272-2761 CE (MOD. 4T-2988) 105314 336-3961 PLATE-WEAR 106276 218-2692 PLATE-WEAR 106384 177-0521 PIN 107465 288-3893 BAR-CUT (USE 288-3893 PRO-E) 107478 263-7847 PLATE-WEAR PAD 20MM/800/1600 107484 263-7848 PLATE-WEAR PAD 108773 218-1921 PLATE-WEAR 108872 242-1663 HOOK ASSEMBLY-PROFILE 9R-5988 109072 272-6050 EDGE SUPPORT 109073 272-6051 EDGE-SUPPORT WING 111514 190-2437 SHAFT 350/5700 111515 190-2439 PLATE-BLOCK 112-2483 238-3169 SIDECUTTER-RH 112-2484 238-3170 SIDECUTTER-LH 112-2487 232-2147 SIDECUTTER-RH 112-2488 232-2148 SIDECUTTER-LH 112-2489 329-5958 PROTECTOR-SIDEBAR 112-2490 275-5982 PIN-G.E.T. 112-6550 244-0980 SEAL KIT 113506 8S-9191 BOLT NC GD.8.38-16THDX 4.00" 116-3600 250-2508 VAVE GP-RELIEF 117702 144-8689 -06 ELBOW 117738 225-7039 HOSE ASSEMBLY 118087 4V-0613 HOSE ASSEMBLY 120298 337-2856 CORNER-RH 120299 337-2859 CORNER-LH 120463 289-1040 EDGE-SPT (CTR) 120464 289-1041 EDGE-SPT (WING) 121557 364-3545 EDGE-CUTTING 121628 364-3546 EDGE-CUTTING 122448 327-9693 MOUNTING BRKT AS. 122811 270-8102 EAR ASSEMBLY BOT LH 122937 283-3122 BOSS 123675 337-2890 PLATE-EAR 123824 231-3348 PIN 200/600 123918 349-5989 EDGE-CUTTING (RH) 123919 349-5990 EDGE-CUTTING (LH) 123953 349-5962 EDGE-SUPPORT (WING) 125027 270-8083 EDGE-CUTTING 128477 380-8362 PLATE-WEAR 129257 163-0168 PLATE-BLANK HOOK 312B 129639 353-4378 PLATE-WEAR PAD 130526 263-7837 BAR-RH (USE 263-7837 PRO-E) 131286 202-8690 BODY-STEEL (LINE MOUNTED) 131909 333-8175 MOTOR GP-ELECTRIC 131910 333-8181 PUMP GP-HYDRAULIC 11
131911 333-8402 TANK GP-HYDRAULIC (BASIC) 132064 171-4809 SHOE AS. 132-1585 230-0312 TUBE ASSEMBLY 132422 281-1220 EDGE-SUPP CTR 20MM/900/15037 133699 302-3941 EDGE-CUTTING (MOD. 4T-6593) 133986 284-7718 CYL GP-BASIC *NP 135650 7M-2275 RING-RETAINING 135-8232 222-7677 TIP-LONG 135-8233 222-7699 PIN 135974 277-5489 PIN AS. *NP 135995 277-5501 BEARING-STRUT 135996 277-5495 BEARING-STRUT 136055 277-5541 HOOK W/SAFETY LATCH 136524 277-3838 BEARING-SLIDE 136525 243-4996 HOSE AS. 136527 277-3856 EAR 136714 277-3840 SPACER 136842 255-9010 HOSE AS. 136846 230-8122 PARTS KIT 137294 252-5357 HOSE ASSEMBLY 137337 246-2934 HOSE ASSEMBLY 137500 281-1885 CYLINDER ASSEMBLY 137579 281-1886 BLOCK-PORT 137587 281-1913 WASHER-THRUST (MOD 092-3306) 137589 281-1914 PIN ASSEM (USE 281-1914 PRO-E) 137590 281-1919 PIN ASSEM (USE 281-1919 PRO-E) 137591 281-1922 PIN ASSEM(USE 281-1922 PRO-E) 137609 281-1915 COLLAR-PLT (USE 281-1915 PRO-E 137610 281-1917 PIN (USE 281-1917 PRO-E) 137611 281-1920 COLLAR-PLT(USE 281-1920 PRO-E) 137612 281-1921 PIN (USE 281-1921 PRO-E) 137614 281-1923 PIN (USE 281-1923 PRO-E) 138457 267-8232 DEFLECTOR 138726 277-5488 TUBE AS. *NP 138987 8C-6869 CONNECTOR-PIPE THREAD 139292 283-7508 CAP-ORFS FEMALE CAP -8 142061 267-8231 CLAMP BASE 144675 218-0123 PLATE-WEAR PAD 145105 122-9868 PLATE-BRACE EAR 146024 277-3837 SLIDE AS-INNER *NP 147-2864 335-4294 PLATE-PAD 147540 170-6709 VALVE GP-COUNTERBALANCE 147751 254-7493 HOSE AS. 147755 309-7414 TUBE-TOP 147973 202-8691 FLOW CONTROL 148210 203-4386 LINES GROUP 148212 203-4186 HOSE ASSEMBLY 148214 203-4182 HOSE ASSEMBLY 148215 203-4265 HOSE ASSEMBLY * 148216 203-4264 HOSE ASSEMBLY * 12
148512 277-5490 BRACKET AS.-U *NP 148860 167-7517 BAR (USE 167-7517) 148870 167-7532 PLATE-EAR (USE 167-7532) 149256 277-3809 BOSS 149748 127-3587 HOOK & PROFILE ASSEMBLY 150-4580/133-8456 200-2100 IR20 ROTATOR GRP 150726 277-3774 PIN ASSEMBLY *NP 150727 277-3787 PIN 100/324 151153 284-7723 VALVE-FLOW DIVIDER 151154 284-7719 PIN (USE 284-7719 PRO-E) 151154 284-7719 PIN *NP 151155 284-7720 PIN-CLIP 151213 319-2826 SPACER 151255 283-3120 COLLAR-PLT(USE 283-3120 PRO-E) 151334 187-9453 VALVE-CHECK 151336 189-2490 ORIFICE 151414 347-6231 CLEVIS 151416 347-6232 HEAD 151417 347-6230 PISTON 151419 347-6229 SHAFT AS. 151421 347-6233 KIT-SEAL 151810 180-9338 CYLINDER GP-BASIC 151857 180-6163 TINE AS.-48" 151864 254-1198 TUBE-LOG GUARD 151884 259-2650 TUBE 50/500/700/8244 151885 180-6157 TUBE 25/200/600/8240 151911 180-8233 TUBE 151916 382-5007 CYLINDER GP-BASIC 151939 180-8357 PIN AS. 151946 179-3191 SHAFT 275/2933 151947 180-8356 TUBE 100/475/75 152132 186-2951 HOSE ASSEMBLY 152154 197-4032 HOSE ASSEMBLY 152222 172-8125 PIN-SNAP 152403 189-4697 VALVE-CHECK 152578 114-4226 PORT PLUG 152825 270-8073 LIFT EAR 152980 188-3120 CYLINDER GP-BASIC 153011 277-5537 PISTON 153-0116 158-4617 LINES GP-CONNECTOR 153305 172-9265 PISTON 153306 243-4961 GLAND 153567 277-3798 BEARING-SLIDE 153912 277-3858 PIN AS. 154158 358-8830 TINE-FORK 154174 277-3800 PIN ASSEMBLY-HINGE *NP 154175 277-3789 SWIVEL AS.-TOP *NP 154176 277-3790 SWIVEL AS.-BTM *NP 154188 4F-2691 BAR 50/50/100 154278 294-5484 SHAFT 13
154281 196-0838 HOSE ASSEMBLY 154283 118-2467 HOSE ASSEMBLY 154284 236-3048 HOSE AS. 154286 101-9175 HOSE ASSEMBLY 154491 277-5491 BRACKET AS.-U *NP 154-5706 344-6146 HOSE AS. 154756 277-3836 CYLINDER GP-HYD 155037 277-3839 SLIDE AS-OUTER *NP 155038 277-3841 PIN (SLIDE) 155148 7I-6049 CYLINDER GP 155197 254-1195 BAR (USE 254-1195 PRO-E) 155429 328-0420 CYLINDER GP-HYDRAULIC 155617 277-5529 ROD AS.-PISTON 155619 105-8117 C'BALANCE VALVE 155843 188-0495 HOOK PLATE ASSEMBLY 155965 326-9765 EDGE-CUTTING (MOD. 1U-0593) 156051 242-9893 CYLINDER GP-HYDRAULIC 156311 277-5535 ROD AS.-PISTON 156312 277-5536 TUBE AS.-BUTT & 156313 277-5538 GLAND 156678 328-0422 BUTT & TUBE ASSEMBLY 156731 110-8660 EXHAUST PIPE 156871 166-7430 RING-PISTON 156903 178-0216 SHAFT-PIN 200/707 157123 8X-7436 HOSE ASSEMBLY 157171 259-0168 EAR ASSEMBLY 157172 259-0169 EAR ASSEMBLY 157434 243-4959 PISTON ROD ASSEMBLY 157435 243-4960 BUTT & TUBE ASSEMBLY 157595 252-2373 HOSE ASSEMBLY 157771 175-7540 VALVE AS-COUNTERBALANCE 157808 193-3979 HOSE ASSEMBLY * 158-2867 180-8451 CYLINDER GP-BASIC 158635 246-5819 HOSE ASSEMBLY 158887 188-4545 HOSE ASSEMBLY 159336 283-7555 VALVE 159358 217-9802 HOOK PLATE ASSEMBLY (Q) 159679 311-6830 PLATE WEAR(USE 311-6830 PRO-E) 159-7405 233-0823 TAILGATE AR-SCISSOR (730) 159742 291-0934 PLATE-BOSS 188/675/40MM 160003 288-4885 PLATE-WEAR 20MM/900/1600 160-7589 180-2593 VALVE GROUP 160-7879.00-171-6896 PIN ASSEMBLY 161067 184-1581 HEAD-FLANGED 161-2938 157-4552 BEARING 161929 283-3117 BOSS 161930 283-3121 PIN 161941 283-7502 HOSE ASSEMBLY 162-0132.00-168-6247 HOSE ASSEMBLY 162344 172-8313 HOOK & PROF 14
162345 172-8314 HOOK PLATE 162565 254-1191 PLATE-HOOK 162-7269 348-5223 VALVE GP-DIVERTER-6-7 (C) 163-0093.00-177-1865 LINES GP-JUMPER/ SEE MEMO 163315 164-6930 HOSE ASSEMBLY 163317 186-2952 HOSE ASSEMBLY 163688 172-8286 CYLINDER GP-BASIC 164231 135-9668 SOLE 164650 263-0122 CYLINDER GROUP-LH 164651 263-0123 CYLINDER GROUP-RH 164769 111-8926 CYLINDER 165-7025 190-6462 VALVE GROUP 165-7054 192-1687 MAIN CUTTER 166133 263-0111 PLATE EAR 166263 245-4337 TINE ASSEMBLY 166-2877 326-3407 PROTECTOR-SIDEBAR 167209 242-1652 HOOK ASSEMBLY-PROFILE 9R7090 167-2459 231-3538 SEAL-WIPER (DOUBLE-LIP) 167-3832 277-5814 SIDECUTTER GP 167-3837 256-8691 SIDECUTTER LH 167409 172-9263 PISTON ROD ASSEMBLY 167410 172-9264 BUTT $ TUBE ASSEMBLY 167411 172-9266 GLAND 167427 188-4548 BAR-TAPPED M12 100/100/300 167713 316-3191 EDGE-SUPPORT 167811 189-4699 PISTON RING 168251 172-8122 PIN ASSEMBLY 168-2604 245-0704 HOSE AS. (SRB 245-0704) 168601 144-8903 BEARING 168-8698 280-9827 MOUNTING GP-HYDRAULIC HAMMER 168950 218-0117 CE SBF N 3.00X23.44X139.00 169-0366 328-3994 JAW GP-BREAKER 169-1726 328-3996 JAW GP-PULVERIZER PRIMARY 169-1727 328-3999 JAW GP-PULVERIZER SECONDARY 169294 270-8045 EDGE-SUPPORT WING 169-7103 328-4012 JAW GP-BREAKER 170372 136-5075 HOSE ASSEMBLY 170-4026 170-1026 LINE GRP WINCH 170621 278-3496 PLATE-HOOK 170622 218-0278 HOOK PLATE ASSEMBLY 170678 172-7997 HOOK PLATE ASSEMBLY 170688 156-9767 TUBE-BOSS 750/438 170690 156-9766 TUBE-BOSS 650/438 170-8014 222-2178 CYLINDER GP (SEE MEM0-222-2178 170925 187-0792 TUBE ASSEMBLY 170926 188-4549 HOSE ASSEMBLY 170927 188-4550 HOSE ASSEMBLY 171210 172-8332 TUBE 50/500/700/9000 171240 106-0594 HOSE ASSEMBLY 171241 188-4554 HOSE ASSEMBLY 15
171242 189-3096 PISTON-ROD AS. 171243 189-3097 BUTT & TUBE AS. 171244 189-3098 PISTON 171245 189-3099 PISTON 171246 189-4694 GLAND 171247 189-4695 GLAND-RETAINER 171248 189-4698 ORIFICE 171-5955 172-8483 BOLT 171672 183-5994 HOSE ASSEMBLY 171974 171-1303 PLATE-EAR 171976 171-1305 PLATE-EAR 171977 171-1306 PLATE-EAR BRACE 171980 172-9259 BLQ-12 BRACE ASSEMBLY 171983 172-8127 PIN AS.-LOCKING 172049 188-0589 HOSE ASSEMBLY 172050 188-0591 HOSE ASSEMBLY 172051 183-5016 HOSE ASSEMBLY 172052 183-5015 HOSE ASSEMBLY 172053 183-5017 HOSE ASSEMBLY 172054 183-5993 HOSE ASSEMBLY 172055 152-9071 HOSE ASSEMBLY 172136 171-1308 PLATE-EAR BRACE 172221 344-9339 HOSE AS. 172224 316-5032 QUICK DISC-PLUG 172244 183-5013 HOSE ASSEMBLY 172245 183-5014 HOSE ASSEMBLY 172272 180-8358 TINE AS.-60" 172302 283-3124 PIN 172512 116-9651 HOSE ASSEMBLY 172564 277-5533 VALVE-RELIEF 172-5887 329-3585 JAW GP-BREAKER 172-5895 329-3577 JAW GP-PULVERIZER PRIMARY 172-5906 329-3579 JAW GP-PULVERIZER SECONDARY 172-5923 325-0745 JAW GP-SHEAR 172-5936 329-3583 JAW GP-SHEAR PLATE 172619 166-5386 TINE 600X1200X6850 172-8286 217-3501 CYLINDER GP 172-8412 307-3141 PIN-ROLL 172-8484 257-5847 KIT-SEAL 172-8486/252-5507 326-5237 KIT-SEAL 172967 134-0784 HOOK-BLANK BQ3F 173143 283-4342 PLATE-WEAR 173-1662 329-3575 JAW GP-COMBINATION 173-1691 325-0815 JAW GP-SHEAR 173171 142-1098 HOSE ASSEMBLY 173171 142-1095 HOSE ASSEMBLY 173355 264-8235 HOSE ASSEMBLY 173412 144-8660 CYLINDER 173413 144-8662 CYLINDER 173448 145-1086 PIN ASSEMBLY 16
173-5805 122-6691 HOSE ASSEMBLY 173930 197-5399 HOSE ASSEMBLY 174077 154-3376 HOSE ASSEMBLY 174150 316-5030 BODY 174151 316-5031 CARTRIDGE-RELIEF 174153 223-0520 HOSE AS. 174302 381-0489 SOLE AS. 174304 381-0491 PIN 174305 381-0499 PIN-KEEPER 174382 380-8363 SHOE AS. 174611 104-9018 HOSE ASSEMBLY 174611 104-9016 HOSE ASSEMBLY 174853 261-5557 TUBE 50/150/150 174867 180-7134 HOSE ASSEMBLY 174873 184-2400 HOSE ASSEMBLY 175863 126-6601 PIN KEEPER 175953 334-4714 CYLINDER GP-HYD 176039 172-8232 HOOK ASSEMBlY 176137 264-9709 TINE AS.-72" 176-1619 288-1695 ARM ASSEMBLY (RH) 176-1620 288-1694 ARM ASSEMBLY (LH) 176735 249-2471 HOSE ASSEMBLY 177219 316-5024 PIN AS. 177220 316-5091 PIN-HEAD 177221 316-5093 PIN-SHAFT 177222 316-5023 PIN AS. 177223 316-5092 PIN-SHAFT 177230 316-5016 ROLLER 177248/184384 248-6326 HOSE ASSEMBLY 177267 281-0422 HOSE AS. 177320 277-3811 CYLINDER GP-HYD 177361 284-7941 TUBE 25/300/300/10615 177417 245-0703 HOSE ASSEMBLY 177593 184-4815 HOSE AS. 177609 309-5593 HOSE AS. 177610 221-9774 HOSE AS. 177669 247-9759 HOSE ASSEMBLY (USE 247-9759) 177674 265-5481 EAR ASSEMBLY 177732 277-4065 HOOK-BLANK BQ3F-F *NP 177767 173-2775 KIT-PARTS (BLQ12 143/163H) 177955 296-4881 EDGE-CUTTING 177958 291-0162 BAR-TOP 50/150/11600 178199 124-3025 BRACE EAR ASSEMBLY (14H) 178261 162-9361 HOSE ASSEMBLY 178404 176-7286 SHAFT 175/200 178863 316-5020 HOSE AS. 178864 316-5021 HOSE AS. 178865 316-5034 KIT-PARTS *NP 178-9110 247-5571 HOSE ASSEMBLY (USE 247-5571) 178941 334-8505 EDGE-SUPPORT 17
179174 197-4033 HOSE ASSEMBLY 179182 334-8511 HOSE AS. (FOR 179183 334-8512 HOSE AS. (FOR 179230 250-5699 HOSE ASSEMBLY 179232 163-7044 HOSE ASSEMBLY 179744 197-4039 TEE FLANGE 179-7518 199-8063 LINES GP-PILOT (C) (320C) *P 179814 197-4036 TUBE ASSEMBLY 179815 186-0888 HOSE ASSEMBLY 179816 197-4050 TUBE ASSEMBLY 179817 197-4037 TUBE ASSEMBLY 179859 197-4034 HOSE ASSEMBLY 179860 197-4035 HOSE ASSEMBLY 17C-002 203-4329 HOSE KIT (LINKS SCRAPER TO 181055 184-4812 HOSE AS. 181561 307-2504 EDGE-SUPPORT (CENTER) 181693 132-3942 DETENT GROUP-BACKHOE LOADER 182307 275-8617 HOSE ASSEMBLY 182317 319-2828 COLLAR 182318 319-2830 WASHER 183226 261-6404 HOSE ASSEMBLY 183227 261-6402 HOSE ASSEMBLY 183228 261-6403 HOSE ASSEMBLY 183311 173-1175 HOOK AS. 183-3929 202-2626 LINES GROUP-COUPLER 183-5095 202-2625 LINES GROUP-COUPLER 183655 337-2910 BRACE AS. 183680 192-0308 CHECK VALVE 183794 319-2827 BAR-TAPPED 183871 319-2829 WEDGE 184096 270-3752 PLATE-EDGE SUPPORT CTR 184097 270-3753 PLATE-EDGE SUPPORT WING 184099 270-3755 SIDE WEAR PLATE 184343 274-9194 PUSH ARM,BRACE GR,SINGLE D10R 184377 283-5823 EDGE-CUTTING 184383 223-7292 HOSE ASSEMBLY 184407 283-5824 EDGE-CUTTING 184609 277-4062 HOOK-BLANK 307 *NP 184643 285-8977 TUBE 175/600/325 184680 326-9771 PIN HEAD 184729 326-9764 BLOCK PORT 184769 327-9702 LINES GP-LIFT CYLINDER 184770 326-9866 LINES GP-TILT CYLINDER 185193 203-3188 BRACKET 185253 188-4555 NUT-COUPLING M12X1.75 185259 166-7148 BRACKET 185-3427 302-4034 CYLINDER GP-HYDRAULIC 185650 175-4033 TINE 450X800X7200/513 185660 241-0719 HOOK ASSEMBLY-PROFILE 914G 185-7022 240-2016 SEAL KIT 18
185-7677 240-6899 SEAL KIT 185-9516 241-7578 PACKING KIT (SEAL KIT) 186315 192-4543 HOSE ASSEMBLY 186-3735 8T-8729 PIN-CONNECTOR 186480 201-5562 LINES GP-IMPLEMENT 416C/446B 186598 305-6305 PLATE-WEAR 186657 168-4526 TINE - 72" 186966 144-8901 ROLLER-PLASTIC (USE 144-8901) 187-0989 6V-3884 SCREW-HEX SOCKET 1/4-20THDX.50 187442 315-2733 TUBE (USE 315-2733 PRO-E) 187501 180-2835 TINE AS. 187548 180-3977 TINE 250X600X7200/263 FL 187655 311-1042 EDGE 187875 225-6584 SHAFT (NEW 225-6584) 188041 238-6664 HOSE ASSEMBLY 188103 180-6403 TUBE 25/300/300/9996 188139 142-4306 TUBE 88/350/235 188181 225-6582 PIN ASSEMB(USE 225-6582 PRO-E) 188460 166-7147 BRACKET 188991 307-2536 LIFT BAR 189069 186-2004 VALVE GP-PRIORITY 24VDC-100GPM 189221 326-9869 LINES GP-DUMP CYLINDER 189557/179755 241-8112 HOSE AS. 189561 6V-9873 ADAPTER-STR 189588 179-3189 PIPE-BOSS 189713 203-5445 HOSE ASSEMBLY 190691 171-4900 HOSE AS. 191308 293-7399 EDGE-SUPPORT 191309 293-7400 EDGE-SUPPORT 191482 315-2725 TUBE-BOSS 191496 315-2724 BAR-STOP 191523 351-5102 PLATE-HOOK 191534 137-0203 TUBE AS. 191535 137-0204 TUBE AS. 191590 313-3322 EDGE-CUTTING 191690 186-0322 HOSE ASSEMBLY 191691 186-0323 HOSE ASSEMBLY 191692 186-0324 HOSE ASSEMBLY 191693 186-0325 HOSE ASSEMBLY 191694 186-0326 HOSE ASSEMBLY 192208 197-5400 HOSE ASSEMBLY 192215 242-9890 HOSE ASSEMBLY 192796 144-8692 HOSE ASSEMBLY 192904 144-6884 (980G) HOOK ASSEMBLY-PROFILE 193017 176-7284 HOSE ASSEMBLY 193018 176-7299 BULKHEAD AS. -12 STOR W/TAB 193040 176-7287 LINES GP-JUMPER 193157 316-5022 HOSE AS. 193185 149-9737 HOSE ASSEMBLY 193228 192-0300 PISTON ROD ASSEMBLY 19
193229 192-0301 BUTT & TUBE ASSEMBLY 193230 192-0302 PISTON 193231 192-0303 PISTON 193232 192-0304 GLAND 193233 192-0305 GLAND-RETAINER 193235 192-0310 PIN-ROLL 193236 192-0311 KEY-SQUARE 193237 192-0312 SEAL KIT (PACKING) 193251 192-0306 LOCKNUT 2.25-12 193290 315-2740 D-SHAPED SLUG 194041 149-0584 HOSE AS. 194045 184-2407 HOSE ASSEMBLY 194175 288-1600 PUSH ARM,BRACE GR,SINGLE D9R 194209 184-4816 HOSE ASSEMBLY 194216 184-2403 HOSE ASSEMBLY 194325 329-1124 EDGE-SUPPORT 194326 329-1125 EDGE-SUPPORT 194646 184-4817 HOSE ASSEMBLY 194689 171-4813 CE (MOD. 4T-2987.PP-) WING 196013 151-7539 BOSS-TAPPED 196812 187-0796 FLANGE-ADAPTER 196903 259-0206 EDGE SUPPORT CENTER 196904 259-0207 EDGE SUPPORT WING 196968 243-4596 HOOK ASSEMBLY-FLAT BACK 196969 178-4660 HOOK AS-PROFILE CAT GP BKT 196970 243-4546 HOOK AS.-PROFILE CAT MH BKTS 196971 243-4544 HOOK AS-PROFILE CAT RK BKTS 197058 278-3498 PLATE-TINE LOCK 197243 187-9473 PISTON 197244 187-9474 PISTON 197265 244-2853 HOOK ASSEMBLY-PROFILE (953)HPL 197396 186-6222 SEAL KIT 197522 177-4978 COMPUTER & DISPLAY UNIT-REMAN 197553 144-8919 ROLLER 197-7373 237-8176 PIN (COUPLER) 197-7374 237-8177 PIN (COUPLER) 197-7375 237-8178 PIN 198232 265-9926 EDGE SUPPORT CTR 198233 265-9927 EDGE SUPPORT WING 198249 265-9944 CE (MOD 4T-3026) 198343 184-2404 HOSE ASSEMBLY 198500 285-4511 PIN GUARD 198501 285-4512 PIN GUARD 198504 285-4528 PIN ASSEMBLY 198507 285-4545 COLLAR-PLT(USE 285-4545 PRO-E) 198508 285-4546 PIN 350/1177 198514 285-4550 PIN ASSEMBLY 198555 285-4608 PIN HEAD 198556 285-4609 PIN 400/747 198557 285-4508 CLAMP-TOP 20
198558 285-4506 CLAMP-CENTER 198559 285-4507 CLAMP-CENTER 199351 186-5093 HOSE ASSEMBLY 199352 186-5096 HOSE ASSEMBLY 199353 186-5098 HOSE ASSEMBLY 199356 186-3494 HOSE ASSEMBLY 199362 285-4596 PIN HEAD 199375 285-4602 HOSE ASSEMBLY 199377 290-8430 HOSE ASSEMBLY 199378 285-4604 HOSE ASSEMBLY 199380 285-4605 HOSE ASSEMBLY 199429 268-3335 PLATE-WEAR (USE 268-3335 PRO-E 199439 116-2131 SLEEVE 199461 175-3712 FERRULE 199586 268-3345 EDGE-SUPP (USE 268-3345 PRO-E) 199-6514 258-4993 LINK GROUP 199-7063 2B-7092 SHAFT-ROUND SPACER 88/51 199814 366-9042 HOSE AS. (USE 366-9042) 199954 151-0712 PLATE-BOSS 199955 151-0711 PLATE-BOSS 200081 165-7203 CYLINDER GP-BASIC 200082 171-6928 CYLINDER GP-BASIC 200459 277-3793 PIN ASSEMBLY *NP 200678 172-6828 PLATE-PAD UPPER 200742 225-6588 BRACKET ASSEMBLY 200765 225-6592 COLLAR-PLATE (NEW 225-6592) 200-7800 291-1266 MOUNTING GP-WORK TOOL 200839 268-3311 HOSE AS. (USE 268-3311 PRO-E) 200864 7I-6936 PLATE-BOSS 200865 7I-6935 PLATE-BOSS 200991 245-1328 HOSE ASSEMBLY 201398 174-5000 PIN 201533 180-7135 BAR 25/350/383 201554 202-9126 HOSE ASSEMBLY 201555 202-9145 HOSE ASSEMBLY 201563 180-7136 TUBE ASSEMBLY 201564 180-7137 TUBE ASSEMBLY 201565 180-7141 TUBE ASSEMBLY 201578 148-7784 HOSE ASSEMBLY 201619 131-9613 HOSE ASSEMBLY 201624 197-5402 BAR 125/300/175 201625 180-7138 BAR 125/300/200 201626 180-7140 BAR 125/300/250 201627 180-7139 BAR 125/300/300 201686 202-9127 HOSE ASSEMBLY 201687 202-9146 HOSE ASSEMBLY 201694 168-2598 HEAD-FLANGED 201695 168-2558 FLANGE-CAPTIVE (FOUR BOLT) 201698 192-4544 HOSE ASSEMBLY 201699 192-4545 HOSE ASSEMBLY 21
201758 202-9165 HOSE ASSEMBLY 201761 202-9167 HOSE ASSEMBLY 201861 225-6593 PIN (NEW 225-6593) 201921 284-2406 TINE 394X960X10000 202160 197-5403 TUBE ASSEMBLY 202187 197-5404 TUBE ASSEMBLY 202315 8X-9145 HOSE ASSEMBLY 202-4307 308-8597 HARNESS GP-WIRING 202543 197-5405 TUBE ASSEMBLY 202588 197-5401 HOSE ASSEMBLY 202788 173-8957 PIN AS. 202789 173-8959 PIN-DOWEL 202791 173-8961 HOSE AS. 202792 173-8962 HOSE AS. 202793 173-8963 HOSE AS. 202794 173-8964 HOSE AS. 202798 176-8564 WIRE LOOM ASSEMBLY 202-8692 153-2996 NIPPLE-QDISC (STOR)(MALE) 202900 173-8955 PIN HEAD 203-0882 355-7063 HAMMER AR-HYDRAULIC 203-0905 355-7065 HAMMER AR-HYDRAULIC 203-8754 118-2657 HOSE ASSEMBLY 205099 255-3610 ADAPTER (USE 255-3610 PRO-E) 205110 239-9781 HOSE ASSEMBLY 205153 187-0795 -16-ADAPT -16FSTOR/M33X2 MALE 205205 176-8565 WIRE ASSEMBLY 205387 179-5753 SHAFT 250/6138 205710 280-2999 HOSE ASSEMBLY 205820 202-9153 HOSE ASSEMBLY 205917 246-1344 HOSE ASSEMBLY 205927 184-2401 HOSE ASSEMBLY 206122 173-8965 HOSE AS. 206272 268-3307 HOSE AS. (USE 268-3307 PRO-E) 206273 268-3308 HOSE AS. (USE 268-3308 PRO-E) 206302 336-6787 PIN *NP 206439 288-1604 PUSH ARM,BRACE GR,DUAL D9R 206633 342-4289 PLATE-WEDGE 206634 342-4290 MOLDBRD-EXT(USE 342-4290 PRO-E 206675 177-9443 HOOK GROUP-BLANK 950G 206687 283-3115 GUARD 206799 311-1690 EDGE-CUTTING 206960 294-5476 HOOK ASSEMBLY 208133 218-2315 PLATE-WEAR 208328 180-7172 SOLENOID GP 208390 277-3731 STOP-RUBBER 208532 202-9131 HOSE ASSEMBLY 208620 308-7817 ARM AS.-RH 208621 308-7816 ARM AS.-LH 208826 191-0102 HOSE ASSEMBLY 208907 285-4556 CYLINDER GP-HYDRAULIC 22
208938 246-1029 HOSE ASSEMBLY 208-9530 336-3608 BEARING-SLEEVE 208997 280-2237 PUSH ARM GROUP DUAL TILT D10R 209030 246-4185 HOSE ASSEMBLY 209121 172-8287 HOSE ASSEMBLY 209122 172-8288 HOSE ASSEMBLY 209885 202-9155 HOSE ASSEMBLY 209975 320-1387 CONTROL AS.-JOYSTICK 210015 209-6406 HOSE ASSEMBLY 210094 252-5358 HOSE ASSEMBLY 210-1115 222-7411 PIN ASSEMBLY 210245 241-4743 HOSE ASSEMBLY 210248 151-9728 HOSE ASSEMBLY 210248 151-9726 HOSE ASSEMBLY 210772 285-9008 PLATE-WEDGE 210856 218-2691 PLATE-WEAR 210860 218-2690 BAR-CUT 210-9269 210-9239 HEAD 600/325 210969 285-4500 CYLINDER GP-HYDRAULIC (DUMP) 210982 113-6711 HOSE ASSEMBLY 211094 285-4509 PIN ASSEMBLY 211095 285-4510 PIN ASSEMBLY 211201 202-9156 HOSE ASSEMBLY 211218 202-9157 HOSE ASSEMBLY 211433 194-7572 HOSE AS. 211-5123 343-2258 EDGE-CUTTING 211690 285-4573 PIN ASSEMBLY 211691 285-4574 PIN ASSEMBLY 211716 147-3111 HOSE ASSEMBLY 211719 285-4597 PIN 225/740 211720 285-4595 PIN 225/663 211721 285-4601 PIN 225/1041 211889 259-2653 (IT38G) HOOK PLATE ASSEMBLY 211981 209-0473 HOSE ASSEMBLY 212073 135-3983 HOSE ASSEMBLY 212073 135-3981 HOSE ASSEMBLY 212767 307-5420 EDGE SUPP (USE 307-5420 PRO-E) 213387 203-4306 HOSE ASSEMBLY 213419 5Q-4208 HOSE ASSEMBLY 213419 5Q-4210 HOSE ASSEMBLY 213422 169-7058 HOSE ASSEMBLY 213661 184-2408 HOSE ASSEMBLY 213719 308-6074 EDGE-SUPPORT (CTR) 213720 308-6075 EDGE-SUPPORT (WING) 213771 192-5381 HOSE ASSEMBLY 214105 192-5382 HOSE ASSEMBLY 214138 105-2702 HOSE ASSEMBLY 214139 192-4328 HOSE ASSEMBLY 214140 192-5080 HOSE ASSEMBLY 214167 164-6933 HOSE ASSEMBLY 23
214180 164-6934 HOSE ASSEMBLY 214220 164-6961 HOSE ASSEMBLY 214254 236-8189 HOSE ASSEMBLY 214298 243-4543 HOOK ASSEMBLY-PROFILE (938G) 214505 270-3779 EDGE-CUTTING 214690 184-2406 HOSE ASSEMBLY 214893 184-1452 TUBE ASSEMBLY 214960 189-4688 CYL GP-BASIC 215051 184-4435 TUBE ASSEMBLY 215365 165-8931 SHIM.3MM 215531 284-7721 PIN 215648 185-4414 HOSE ASSEMBLY 215933 254-4983 EDGE-SUPPORT 150/1150/12676 215934 254-4984 EDGE-SUPPORT 150/1150/8184 215964 319-7468 RETAINER-PIN 216-1409 239-5296 LINES GP-FRONT 216374 285-9319 PLATE-LEVER 216646 7I-7882 HOSE ASSEMBLY 216646 7I-7881 HOSE ASSEMBLY 216772 283-7505 CYLINDER GP.-HYD (RH) 216773 283-7506 CYLINDER GP.-HYD (LH) 216824 289-2751 HOSE ASSEMBLY 217-4897 309-1121 TIP GP-WIDE *NP 217-4898 309-1122 TIP GP-EXTRA DUTY *NP 217-4899 309-1123 TIP GP-PENETRATION *NP 217-4900 309-1124 TIP GP-PENETRATION PLUS *NP 217-4901 309-1125 TIP GP-SPIKE *NP 217-4902 309-1126 TIP GP-DOUBLE SPIKE *NP 217-4903 309-1127 TIP GP-GENERAL DUTY *NP 219738 144-5496 CYLINDER GUARD 219800 315-0253 HOSE AS. 220-9168 309-1128 TIP GP-HEAVY PENETRATION *NP 220-9169 309-1129 TIP GROUP-HEAVY ABRASION *NP 222-8506 343-3323 MOUNTING GP-WORK TOOL 222-8507 342-6556 MOUNTING GP-WORK TOOL 222-8508 365-9063 MOUNTING GP-WORKTOOL 225-6023 236-7797 BASE ASSEMBLY (D-LINK) 225-8754 257-7244 LINK AS.-LONG 227-4062 257-7245 LINK AS.-SHORT 227-4905 236-7726 BASE ASSEMBLY (307) 230610 196-4607 BOLT 230-7747 303-2387 PIN 230-7802 294-8245 CYLINDER ANCHOR 232-2147 357-2696 SIDECUTTER-RH 232-2148 357-2697 SIDECUTTER-LH 232-4103 285-1531 VALVE GROUP-BANK 2 233-4675 349-8365 MOUNTING GP-WORK TOOL 237-7250 344-0976 LINK GP-TILT (950G-HL) 238-2399 324-5733 HARNESS AS. 239-1808 354-3806 HOSE AS. 24
239-5012 246-4696 PLATE-WEDGE 241-8514 LAVAL 341-6160 TINE AS.-RH (60" LG.) 243-1662 319-8948 (320C) LINK AS.-LH 243-1662 319-8950 (322C) LINK AS.-LH 243-1727 319-8947 (320C) LINK AS.-RH 243-1727 319-8949 (322C) LINK AS.-RH 247-5461 319-0399 (320C) LINK AS.-RH 247-5461 319-0401 (322C) LINK AS.-RH 247-9197 326-4362 HOSE AS. 251-4624 333-0098 MOUNTING GP-HYDRAULIC HAMMER 252-5507 326-5946 KIT-SEAL 252-5507 326-5051 KIT-SEAL 252-5507 326-5235 KIT-SEAL 256-0217 262-5938 LINK GP 256-3108 344-1058 MOUNTING GP-WORK TOOL 256-8690 326-3405 SIDECUTTER-RH 256-8691 326-3406 SIDECUTTER-LH 257-7737 306-9205 KIT-COVER 260-7953 307-5183 HOSE AS. 263-6061 318-2133 CYLINDER GP-BASIC 263-9745 279-5253 UB 1981GP -78-4.54-6 -LE 264-0592 318-2132 CYLINDER GP-BASIC 264-6934 331-4245 330 LINK AS.-RH 264-6935 331-4243 330 LINK AS.-LH 266-0165 325-7643 LINK AS.-RIGHT (IDLER) 266-0168 325-7642 LINK AS.-LEFT (IDLER) 266-1307 317-4712 HOSE AS. 266-1311 314-8205 HOSE AS. 269-7320 367-9361 PIN-CLEVIS 269-7323 367-9360 PIN-CLEVIS 270-5102 305-8112 MANIFOLD AS.-ROTATING 275-2413 358-8745 PIN 275-2414 358-8746 PIN 275-2415 358-8747 PIN 275-2418 275-6083 BEARING 275-5878 337-2921 MAST GP 275-5882 337-2919 TUBE GP-TEL 275-6081 358-8748 PIN 275-6082 358-8749 PIN 277-3796 377-2986 ACCUMULATOR GP-50-0.64 (A) 277-4065 331-1905 HOOK-BLANK 277-5524 337-2920 TUBE AS. *NP 278-6785 302-2857 HOSE AS. 278-8149 257-3655 PLATE-WEAR 279-3898 329-1718 BLOCK-HIGH 279-7324 335-4070 TINE GP (LOWER) 279-7384 358-8750 PIN 279-7387 358-8751 PIN 280-8180 302-4343 CLAMP ASSEMBLY (980G/H) 280-8982 267-9463 PIN 25
280-9009 204-4962 PIN 282-2960 358-8752 PIN 282-2983 358-8753 PIN 282-7061 319-9996 HOSE AS. 282-8524 358-8754 PIN 282-9546 333-9970 LINK AS.-RH 282-9547 333-9971 LINK AS.-LH 283-5875 358-8755 PIN 284-3712 326-9474 PIN 354/3000 284-5622 358-8756 PIN 284-5628 327-0314 PIN 393/3303 285-2517 278-6731 LINES GP-PUMP (B) 285-2693 286-6596 HOSE AS. 285-2783 354-3821 HOSE AS. 286-7916 292-8935 COVER EDGE PROTECTOR GROUP 289-3406 346-4875 PIN AS. 297-1548 302-8395 HOOK AS. *NP 2G-7309 330-6877 SHAFT 3009070019 230-0846 PIN 304-3516 327-7034 SEAL-KIT 304-8069 346-3539 PIN-SECONDARY HOOK 306817 030--6817 ADAPTOR 90DEG NPS-06F STO-06M 308-0300 351-0296 KIT-HYDRAULIC 309-1044 345-0387 TIP GP-HWY ABRSN-SLAG (K110) 311-1817 324-5258 EDGE-SEGMENT 312-6023/312-2997 323-5871 HOSE AS. 313-1420 324-7421 HOSE AS. 313-1497 323-9430 HOSE AS. 315-6133 326-4363 HOSE AS. 315-9802 326-4191 HOSE AS. 318-8149 341-2097 MOUNTING GP-WORK TOOL 319-9865 354-3814 HOSE AS. 320-0135 354-3817 HOSE AS. 321-1182 346-6902 PIN AS. 322-5191 310-2788 KIT-PIN 324-5282 330-2174 BLOCK-SHEAR 325-5880 359-6060 LINES GP-CONNECTING (LH) 325-5881 359-6061 LINES GP-CONNECTING (RH) 327-3598 329-8805 BLOCK-SHEAR 328-0421 349-5881 ROD AS.-PISTON 328-8807 346-3540 PIN 330-2454 366-8644 HOSE AS. 333-1666 359-6059 LINES GP-CONNECTING (RH) 333-1667 369-3693 LINES GP-CONNECTING (LH) 333-7071 366-8643 HOSE AS. 334-9043 338-0135 HOSE AS. 335-7412 338-0133 HOSE AS. 335-9209 338-0136 HOSE AS. 339-1358 333-0833 EDGE-BASE 346-3048 359-2912 HOSE AS. 26
346-3049 359-2913 HOSE AS. 346-3086 359-2914 HOSE AS. 346-3087 359-2915 HOSE AS. 346-3095 353-0160 PLATE-WEAR (CENTER) 347-3729 359-2909 HOSE AS. 347-3730 359-2911 HOSE AS. 359-2916 364-9169 HOSE AS. 359-2917 364-9170 HOSE AS. 364-1431 368-7783 HOSE AS. 364-1432 368-7784 HOSE AS. 369-2632 317-0740 PIN 37206025 172-8514 HOSE AS. 3800085 LAVAL 289-0606 COUPLING 3801276 LAVAL 273-5595 PIN-LYNCH 3Q-7609 251-4598 MOUNTING GP-HYDRAULIC HAMMER 40061 144-3140 HOSE-HYDRAULIC 40063 144-2755 HOSE-HYDRAULIC 40066 144-2766 HOSE-HYDRAULIC 402272 192-0372 TUBE RETAINER 38/400/150 405543 281-1927 CE SBF(USE 281-1927 PRO-E) 406078 192-0376 PIN 406429 192-0324 CYLINDER 406465 189-3095 CYL GP-BASIC 407983 192-0295 CYLINDER GP-BASIC 411821 217-9841 STOP RUBBER 411822 285-4504 SHIM 412178 302-3959 CE SEF P 25MMX8.00X136.26 412179 302-3960 CE SEF P 25MMX8.00X 60.13 412195 299-8443 EDGE-CUTTING RH WING 412196 299-8444 EDGE-CUTTING LH WING 412197 299-8446 EDGE-CUTTING WING CENTER 412198 299-8445 EDGE-CUTTING WING 412789 329-7754 EDGE-SUPPORT 413165 187-9551 PIPE-RETAINER 150/150 413648 185-8072 BLANK HOOK (315) 413759 187-9494 TUBE-SPACER 413760 187-9495 TUBE-SPACER 113/450/128 413761 187-9496 TUBE-SPACER 113/450/44 413844 187-9543 PIN ASSEMBLY 413863 187-9545 COLLAR-PLATE 413963 187-9491 PIN ASSEMBLY 413964 187-9492 PIN-SHAFT HARDEN 242/2338 413965 187-9493 COLLAR-PLATE 414175 312-5341 HOSE AS. 414507 177-4517 HOSE ASSEMBLY 414508 177-4518 HOSE ASSEMBLY 5002010007 230-0863 HOSE ASSEMBLY 502015 143-8453 HOSE ASSEMBLY 502016 199-1959 HOSE ASSEMBLY 502016 199-1957 HOSE ASSEMBLY 27
502017 3Z-9672 HOSE ASSEMBLY 502500500 187-2993 CYLINDER 502800633 197-8298 HOSE 606269 225-6583 COLLAR-PLATE (NEW 225-6583) 606402 208-6694 CYLINDER 3.50 DIAX13.81 STROKE 606404 209-7275 PIN 4140 TG&P 300/2062 61100024 196-4129 SHIM 61100025 196-4130 SHIM 618408 061-8408 RACCORD TE 62300010 196-4131 SHIM 718-030-011 240-5643 PINION OBSOLETE SEE718-030-018 8S-3759 6V-4657 CAT REUSABLE COUPLING.750 9117785 9117788 FROST BIT 9W-2673 / 8E-6358 114-0358 PIN-G.E.T. A2-10038 278-0326 PLATE-WEAR A2-10091 268-2732 BAR A2-10092 LAVAL 288-6086 BAR 38/200/657 A2-10374 LAVAL 290-8422 PIN 275/689 A2-12154 289-2394 BAR A2-13535 LAVAL 265-7221 STOPPER A2-13627 247-3940 BAR A2-8039-01 LAVAL 289-2385 BAR-SQUARE 400/400/3000 A2-8416 LAVAL 288-6096 PIN 200/1307 A2-9565-03 LAVAL 288-6097 TUBE 63/300/51 A8-4999 7X-7877 CAOUTCHOUC EN"U"1/4"(7X-7877) B2-10416-01 LAVAL 295-0251 PIN 250/1732 B2-11019 290-3354 PLATE-WEAR B2-11753-07 LAVAL 265-7185 TUBE-BOSS 125/400/31 B2-13051 LAVAL 284-7657 CE SBF P 20MMX 7.99X120.00 B2-3950 290-6032 EDGE-CUTTING (MOD. 4T-6508) B2-3952 LAVAL 288-6077 EDGE-CUTTING (MOD. 4T-6511) B2-4502 269-5850 TUBE B2-4505 269-7321 PIN B2-9729-02 LAVAL 288-6088 PIN 250/1732 B2-9730-01 LAVAL 311-3621 SHAFT 150/733 B2-9982 278-0324 CE SBF P 25MMX 8.07X 122.99 B4-10416 LAVAL 275-1268 PIN ASSEMBLY B4-11715 269-3664 PIN AS. B4-11837 LAVAL 308-6874 PIN ASSEMBLY B4-13692 266-8938 PIN AS. B4-13692-02 266-8940 PIN 150/500 B4-16125 368-4244 TINE AS.-LH B4-16126 368-4243 TINE AS.-RH B4-5071 LAVAL 301-6772 PIN ASSEMBLY B4-9729 LAVAL 288-6087 PIN ASSEMBLY B4-9730 LAVAL 275-1033 PIN AS. B6-10882 LAVAL 275-0897 CE DBF P 35MMX 10.00X 83.91 B6-8196 LAVAL 288-3961 EDGE-CUTTING (MOD. 4T-3036) C2-2885-02 LAVAL 288-6093 PIN 200/769 C2-2885-03 268-2730 PIN 200/588 28
C2-2885-11 LAVAL 307-9985 PIN 250/600 C2-2885-4 LAVAL 308-1437 PIN C2-2885-42 269-3665 PIN C2-7166 267-5342 CYL HEAD (USE 267-5342 PRO-E) C2-9356-02 LAVAL 289-2381 TUBE 100/400/3012 C4-2899-02 LAVAL 288-6091 PIN ASSEMBLY C4-2899-03 268-2670 PIN ASS'Y C4-2899-11 LAVAL 275-1004 PIN ASSEMBLY C4-2899-26 LAVAL 275-1035 PIN ASSEMBLY C4-6029 271-6712 ARM ASSEMBLY C4-7172 269-5963 ARM AS. C6-98370 LAVAL 288-6090 EDGE-CUTTING (MOD. 4T-2967) CV00000 272-5608 BLANK HOOK 910/914/924F CV00001 276-9075 HOOK ASSEMBLY (920) CV00003 273-9038 HOOK ASSEMBLY-BLANK (950) CV00004 273-9039 BLANK HOOK 928G/938G CV00005 274-9467 HOOK GP-BLANK CV00009 LAVAL 309-0116 (980H) HOOK GP-BLANK CV00058 281-7201 HOOK GP-BLANK CV00059 LAVAL 281-8476 HOOK ASSEMBLY (446) CV50056 274-9477 (IT38G) HOOK GP-BLANK D2-6390-03 LAVAL 270-3921 TUBE 100/400/2685 D2-9940-05 247-3932 BAR 0.62"X0.62"X1499LG D4-6343 268-2674 CYLINDER GP-BASIC D4-9812 LAVAL 264-6009 CYLINDER GP-BASIC H004260 LAVAL 233-0153 BAR H004364 269-6527 TINE AS. H004365 LAVAL 272-6500 TINE 250X800X4800/3.06 H004366 LAVAL 272-6501 TINE 250X800X6000/3.06 H004367 LAVAL 272-6502 TINE 250X800X7200/3.06 H004369 LAVAL 272-6503 TINE 250X800X9600/3.06 H004380 248-0649 TUBE-BOSS 100/450/91 H004430 248-0650 TUBE 38/500/500/7319 H004510 248-0655 HOOK FORK IT H004540 248-0659 SHAFT 250/7469 H004550 258-4713 SHAFT 3." (USE 258-4713 PRO-E) H004680 LAVAL 275-3372 PIN ASSEMBLY H004690 LAVAL 303-8309 PIN-FORMED 75/1240 H004890 238-9648 PLATE-HOOK (LH) H004891 238-9646 PLATE-HOOK (RH) H004922 238-9641 BAR LH H004925 LAVAL 273-7352 HOOK ASSEMBLY H004926 LAVAL 238-9640 BAR-RH H018110 269-7322 BLOCK H018150 278-6332 ROD H038347 145-3574 COUPLING H044180 LAVAL 275-1282 PLATE-WEAR H044261 LAVAL 271-6738 BOSS H045330 LAVAL 275-1007 PLATE-WEAR H045700/CV00058 LAVAL 274-9496 HOOK ASSEMBLY-RH 29
H050350 270-3990 PLATE-WEAR H051800 LAVAL 307-3762 PLATE-WEAR PAD 12MM/787/1496 H052622 285-5313 PLATE-EDGE H055801 293-0649 ARM-SIDE (VERTICLE) H057170 LAVAL 278-3401 EDGE H05778 LAVAL 274-9505 446 HOOK ASSEMBLY-LH H069610 LAVAL 288-6084 EDGE-CUTTING H069970 247-3933 BAR LOCKING H070920 290-6031 PLATE-SHIM H076860 LAVAL 292-5488 SLEEVE H081370 288-6085 PROT-SDB (USE 288-6085 PRO-E) H084432 251-5572 BAR WEDGE H087360 251-8229 STOPPER WEDGE H087520 174-8026 BOLT-ON EDGE H087580 105-2345 CE 1"X245X2681LG(USE 105-2345) H092270 LAVAL 274-9507 BOLT GR.8 1.0"X14THDX10.00"HEX H096050 247-3934 TINE 150X500X4800/2.06 H096051 272-5441 FORK AS. 1.50"X127X610X1524 H096080 247-3938 SHAFT 200/5988 H100260 283-0973 PIN H101820 247-3923 HOOK H107640 268-4725 CYLINDER GP-BASIC H112690 LAVAL 271-6715 TUBE 100/400/4787 H112710 LAVAL 271-6728 BAR 400/400/3012 H112730 LAVAL 271-6720 STOPPER H112830 LAVAL 285-5104 PIN-HARDENED 250/1535 H112840 283-0967 BAR ASSEMBLY H113310 LAVAL 285-6702 HOOK ASSEMBLY-LH H113311 LAVAL 285-6705 HOOK ASSEMBLY-RH H113460 LAVAL 275-5638 BLOCK ASSEMBLY H114640 LAVAL 257-2074 HOOK ASSEMBLY-RH (345) H114641 LAVAL 257-2075 HOOK ASSEMBLY-LH (345) H115040 LAVAL 271-6729 BOSS H116130 355-9515 EDGE-CUTTING H116800 LAVAL 287-5432 PLATE-WEAR H116801 LAVAL 287-5433 PLATE-WEAR H116802 LAVAL 287-5434 PLATE-WEAR H116870 LAVAL 287-5435 PLATE-WEAR H116871 LAVAL 287-5436 PLATE-WEAR H116872 LAVAL 287-5437 PLATE-WEAR H116873 LAVAL 287-5438 PLATE-WEAR H118600 268-2678 CE SBF.98X 9.65X123.78 H119060 268-2666 HOOK ASS'Y H119290 268-2673 HOSE ASS'Y H119540 268-2669 LOWER PLATE ASS'Y H120190 LAVAL 276-7946 CE SBF N 22MMX 7.99X 30.00 H12201 LAVAL 283-8255 CE SBF N 22MMX7.99X144.02 H127700 LAVAL 265-7193 CE SBF P 20MMX 7.99X108.85 H127710 LAVAL 269-6509 EDGE-CUTTING H129000 248-0658 PLATE-LOCK 30
H129010 LAVAL 258-4714 PLATE-LOCK H139710 283-0960 BAR-ATTACHMENT H142240 LAVAL 275-3551 SHOE GROUP H142320 LAVAL 267-4954 INSTALLATION AS-HYDRAULIC H142331 267-4955 HOSE ASSEMBLY H142332 LAVAL 267-4956 HOSE ASSEMBLY H144960 LAVAL 284-2437 CE SBF N 25MMX 7.99X 35.98 H145530 251-2328 PIN AS. H145540 251-2329 PIN H146430 251-2337 BLOCK-PORT H147390 LAVAL 288-3965 SHOE ASSEMBLY H150530 283-3118 PIN AS. H150540 283-3119 PIN H151070 251-2331 PIN AS H151080 251-2334 PIN ASS H151200 251-2342 PLATE-WEAR H151290 251-2332 PIN H151300 251-2335 PIN H151320 LAVAL 251-2338 HOSE AS. H151330 LAVAL 251-2339 HOSE AS. KBG0502 290-7416 EDGE GP-CUTTING KG01100 293-3048 EDGE GP-CUTTING KG01101 1U-2416 KIT BOLT-ON BUCKET GP 112" KGP1301 1U-0633 KIT P.P BUCKET 131"(9V-6574) LAVAL H091550 283-0972 BOLT GR.8.75"X16THDX 7.50"HEX LAVAL H100470 281-2032 HOOK ASSEMBLY-RH LAVAL H100471 281-2034 HOOK ASSEMBLY-LH LAVAL H113210 271-8123 PLATE-WEAR S016590 LAVAL 273-0399 SQUARE BAR 400/400/3206 S075860 LAVAL 275-1300 PIN ASSEMBLY S075870 308-9999 COLLAR S075880 308-9995 PIN S078201 LAVAL 288-5359 BLOCK ASSEMBLY-RH S08830 LAVAL 308-2806 PLATE-WEAR S08854 LAVAL 308-2814 EDGE-CUTTING (HALF ARROW) S104350 LAVAL 288-6078 EDGE AS. S104360 LAVAL 288-6080 EDGE-CUTTING (MOD. 7J-2963) S104370 LAVAL 288-6079 EDGE-CUTTING (MOD. 7J-2963) S105390 278-5072 CE SBF N 36MMX12.28X 36.00 S105520 217-2765 PLATE-SHIM S105530 217-2766 PLATE-SHIM S112920 LAVAL 288-6104 CE SBF N 76.2MMX24.0X191.99 S113550 247-8051 (322) BOTTOM FRAME ASSEMBLY S113560 247-8063 PIN-HARDEN 300/1600 S113570 247-8067 PIN ASSEMBLY S114330 LAVAL 280-2757 TUBE 175/600/256 S114380 247-8068 PIN 175/737 S114460 USE 247-8060 247-8062 BLOCK-HIGH 175/236/575 S114470 247-8058 PLATE-WEAR LH S114490 247-8075 HYD. LINES GP TILTING COUP *NP 31
S114510 247-8057 TUBE 130/563/919 S114520 251-2340 CE SBF P 25MMX 9.06X 59.84 S114620 247-8059 PLATE-WEAR RH S114630 247-8060 BLOCK AS. S114740 247-8070 LOCKING PIN ASSEMBLY S114750 247-8071 PIN 297/987 S114780 247-8065 PLATE-SHIM 113/530/06 S114790 247-8066 PLATE-SHIM 113/530/12 S114800 247-8064 PIN 88/637 S114880 247-8050 SPACER 56/349/173 S115910 247-8076 HOSE AS. S115920 247-8077 HOSE AS. S116020 247-8078 BLOCK-MTG 75/100/236 S117560 217-2128 BAR-SHIM 50/125/642 S117570 217-2125 SHIM S117580 217-2126 SHIM S122070 217-2767 PLATE-SHIM S12291 LAVAL 294-7908 TINE 200X800X5400/2.56 S124220 216-5595 SLEEVE-WEAR S124250 217-2127 SHIM S124260 257-3867 PIN-LOCK S(USE 257-3867 PRO-E) S124630 278-5001 EDGE-CUTTING S124860 257-3854 BAR-CUT. S124890 257-3856 PLATE-WEAR FORM 8MM/591/2756 S127320 228-5247 CYLINDER GP-BASIC S128180 LAVAL 275-8780 CE SBF P 20MMX 7.09X 47.82 S128260 LAVAL 297-2541 PLATE-WEAR S132500 257-3863 TUBE AS S137600 247-8074 PLATE-SHIM 113/530/20 S138310 2K-6564 PIN S140520 280-1885 HOSE ASSEMBLY S143260 LAVAL 272-6363 HOSE AS. S143270 LAVAL 272-6364 HOSE AS. S144950 239-7428 LINES GROUP-HYDRAULIC *NP S145730 LAVAL 282-2718 HOSE AS. S146790 LAVAL 313-3519 TUBE AS. S146920 LAVAL 313-3521 TUBE-SQUARE SAME AS CE-1 99-2982 CUTTING EDGE SAME AS CE-2 9416129 FROST BIT VS436102 195-0788 LOCK NUT VS602301 197-7190 PIN VS602304 197-7194 LOCK NUT VS603701 195-0782 PIN VS603710 170-3669 LOCK VS607801 201-8835 LOCK NUT WRENCH VS607802 201-8836 ADJUSTING RING WCV00029 253-3848 311 BLANK HOOK WEDGE 311 WCV00033 253-3853 330 HOOK GP.- BLANK WCV00034/H11464-2 253-3854 345 BLANK HOOK AS. (WEDGE) 32
Generic number Dwg number Description CV00003 H005003 950 CROCHET VIERGE MOD:A 950 CV00004 H005004 938 CROCHET VIERGE 926/928/936/938 CV00005 H005005 950 CROCHET VIERGE 950B@ G/966D@ G/972G CV00006 H005006 966 CROCHET VIERGE MOD:966C CV00009 H006490 980 CROCHET VIERGE 980C/F/G CV00056 H076640 260-95 IT38 CROCHET VIERGE IT38F/936IT/950IT/ CV00057 H006440 C4-8109 104-85 IT CROCHET VIERGE IT12@ 28/416@ 436IT CV00058 H045700 416 CROCHET VIERGE COUPLEUR AVANT CV00059 H057780 163-92B 446 CROCHET VIERGE (2 REQUIS) CW01500 H103070 /241-97 IT CONTREPOIOS 348LBS MOD:IT28 & 928F CW02201 H098530 163-97 928 CONTREPOIOS (525LBS) 928G CW05602 H074080 217-95 938 CONTREPOIOS ARR MOD:F CW11300 H048280 950 CONTREPOIOS ARR 950F&966F SERIE II CW14000 H048281 950 CONTREPOIOS ARR 950F&966F SERIE II CW16300 H102460 / 208-97 330 CONTREPOIOS 3600 LBS MOD:BL FC48200 H096070 /D4-10422 416 CHARIOT&FOURCHES CHARN. 48" FC48201 H005400 926 CHARIOT&FOURCHES CHARN. 48" 928 FC48203 H00547 938 CHARIOT&FOURGHES CHARN 48" 936/938 FC48204 H005650 930 CHARIOT&FOURCHES GHARN. 48" FC48205 H092040 274-96 914 CHARIOT&FOURCHES CHARN. 48" MOD:G FC48206 H005190 924 CHARIOT&FOURCHES 48" CHARN 916&924 FC48208 H132690 369-00 924 CHARIOT&FOURCHES 48" CHARN 924G FC48250 H044350/D4-9938 416 CH0RIOT&FOURCHES CROCH. 48" FC48252 H005090 910 CHARIOT&FOURCHES CROCH.48" 910/916 FC48253 H005130 938 CHARIOT&FOURCHES CROCH 48"926/936 FC48254 H004480 143-85 IT CHARIOT&FOURCHES CROCH 48" FC48255 H07756O IT38 CHARIOT&FOURCHES CROCH 48" F FC48256 H080910 371-95 446 CHARIOT&FOURCHES CROCH. 48" FC48257 H101800 198-97 4161T CHARIOT&FOURGHES CROCH. 48"416@ 4 FC48260 H029040 131-91 IT CHARIOT&FOURCHES CROCH.48" PROF BAS FC48261 H144270 TEXTE N/S MACHINE IT CHARIOT&FOURCHE POS LATERAL 48" FC48350 H005140 D4-7322 950 CHARIOT&FOURCHES CROCH 48" MOD:B@ F FC54251 H005105 / 350-00 920 CHARIOT&FOURCHES CROCH. 54" FC60203 H005471 938 CHARIOT&FOURCHES CHARN 60" 936/938 FC60207 H106471/328-97 928 CHARIOT&FOURCHES 60" CHARN 928G FC60250 H044351 416 CHARIOT&FOURCHES CROCH. 60" FC60253 H005131 183-85 938 CHARIOT&FOURCHES CROCH 60"926/936 FC60254 H004481 IT CHARIOT&FOURGHES CROCH 60" FC60255 H077561 IT38 CHARIOT&FOURCHES CROCH. 60" F FC60256 H080911 369-96 446 CHARIOT&FOURCHES CROCH. 60" FC60257 H131850 /336-00 4161T CHARIOT&FOURCHES CROCH. 60"416@ 4 FC60261 H129030 164-00 IT CHARIOT&FOURCHE POS LATERAL 60" FC60262 H129220 179-00 IT62 CHARIOT&FOURCHES CROCH60"1T50/IT6 FC60300 H006091 950 CHARIOT&FOURCHES CHARN 60" MOD:B@F FC60350 H005141 950 CHARIOT&FOURCHES CROCH 60" MOD:B@ F FC60352 H005151 966 CHARIOT&FOURCHES CROCH.60" MOD:C FC60356 H005141 (FC60350) 966 CHARIOT&FOURCHES CROCH 60" MOD:G FC72203 H005472 938 CHARIOT&FOURCHES GHARN 72" 936/938 FC72250 H121850 / 219-99 4161T CHARIOT&FOURCHES CROCH.72"416@ 43 FC72253 H005132 183-85 938 CH00IOT&FOURCHES CROCH 72"926/936 FC72254 H004482 IT CHARIOT&FOURCHES CROCH. 72" FC72255 H077562 IT38 CHARIOT&FOURCHES CROCH. 72" F 33