Product: CAS #: Product Use: Manufacturer/Supplier: Company Name: Company Address: Section 1 - Product and Company Identification Alumilite Flex 30, 40, 60, 70, and 80 A Side Non-Applicable Mold Making and Casting Alumilite 315 E. North St. Kalamazoo, MI 49007 Telephone Number: 269-488-4000 Emergency Telephone: Chemtrec 1-800-424-9300 Section 2 - Hazards Identification 2.1 Classification of the substance or mixture GHS Classification in accordance with 29 CFR 1910 (OSHA HCS) Acute toxicity, Inhalation Not Classified Skin irritation Not Classified Eye irritation Not Classified Respiratory sensitization Not Classified Skin sensitization Not Classified Specific target organ toxicity Not Classified For the full text of the H-Statements mentioned in this Section, see Section 16. 2.2 GHS Signal Word, Hazard Statement, Symbol Pictograms by CLP/GHS: Signal Word: Not Required Not Required Hazard Statements: May cause eye, skin, and respiratory irritation. May cause gastric distraction if swallowed. 2.3 Hazards not otherwise classified (HNOC) or not covered by GHS Harmful if swallowed. May cause skin irritation. May cause respiratory irritation. Section 3 - Composition / Information on Ingredients CAS No. Percentage Polyol 9082-00-2 85-95% Polyol System 110-63-4 1-10% Curative 25265-71-8 <1% Alumilite Flex 30, 40, 60, 70 and 80 A Side Page 1 of 4 67318-020303 A
Section 4 - First Aid Eye Contact: Skin Contact: Inhalation: Ingestion: In case of eye contact, immediately flush with plenty of water for up to 15 minutes. Remove any contact lenses and open eyes wide apart. Get medical attention if irritation develops or persists. In case of skin contact with contents of product, remove contaminated clothing and wash skin with soap and water. Get medical attention if irritation develops. Remove the affected person into fresh air. Assist in breathing if necessary. Drink large quantities of water if accidentally ingested. Get medical attention if any discomfort continues. Do not induce vomiting. Section 5 - Fire Fighting Measures Extinguishing Media: Water. Foam. Dry powder. Carbon dioxide (CO2). Fire Fighting Instructions: Treat as a class B fire. Flash Point: Side A: >200 F Section 6 - Accidental Release Measures General: Waste Disposal: Extinguish all ignition sources. Avoid sparks, flames, heat and smoking. Ventilate. Avoid inhalation of vapors and contact with skin and eyes. Wear suitable protective clothing. See Section 8 of the MSDS for Personal Protective Equipment. Do not allow to enter drains, sewer or water course. Section 7 - Handling and Storage General: Storage: Wash thoroughly after handling. Remove contaminated clothing and wash before reuse. Avoid contact with eyes. Avoid ingestion and inhalation. Store in a cool, dry place. Keep container closed when not in use. Section 8 - Exposure Controls & Personal Protection Clothing: Eyes: Respiration: Ventilation: Wear chemical goggles. Section 9 - Physical & Chemical Properties Appearance: Color: Odor: ph: Boiling Point/Range: Melting Point/Range: A Side Liquid Clear Yellow Mild Not Known Not known Not known Section 10 - Stability & Reactivity Chemical Stability: Stable Conditions To Avoid: Avoid excess heat and source of source of ignition. Incompatible Materials: Avoid contact with moisture. Keep away from strong base and acid. Hazardous Decomposition Products: At thermal decomposition temperature, carbon monoxide and carbon dioxide. Alumilite Flex 30, 40, 60, 70 and 80 A Side Page 2 of 4 67318-020303 A
Section 11 - Toxicological Information Toxicity Data Acute Toxicity: Inhalation: Skin Contact: Eye Contact: Ingestion: Chronic Toxicity: A Side No information about product s acute toxicity available. May cause skin irritation. May cause eye irritation. Not known. (May be fatal) No information about product s chronic toxicity available. Section 12 - Ecological Information (Non Mandatory) Bioaccumulation: Ecotoxicity Effects: Mobility: Section 13 - Disposal Information (Non Mandatory) Disposal Instructions: Contaminated Packaging: Dispose of waste and residues in accordance with local authority requirements. Since emptied containers may retain product residue, follow label warnings even after container is emptied. Section 14 - Transportation Information (Non Mandatory) Not a DOT controlled material. ORM-D. (US) Section 15 - Regulatory Information (Non Mandatory) Under the criteria of the Federal OSHA Hazardous Communication Standard 29 CFR 1910.1200 Symbols, R/S Phrases: No data available. Hazardous Health Rating: Health: 2 Fire: 1 Reactivity: 1 Alumilite Flex 30, 40, 60, 70 and 80 A Side Page 3 of 4 67318-020303 A
No data available In accordance with Occupational Safety and Health Act (1970), Section 16 Other Information The information contained in this Safety Data Sheet is to the best of Alumilite's knowledge and belief, accurate and reliable as of the date compiled. However, no representation, warranty or guarantee is made as to its accuracy, reliability or completeness. NO WARRANTY OF MERCHANTABILITY, FITNESS FOR ANY PARTICULAR PURPOSE OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, IS MADE CONCERNING THE INFORMATION HEREIN PROVIDED OR ANY RELATED PRODUCT. User is responsible for determining whether the Alumilite product is fit for user's particular purpose and suitable for user's use or application. Given the variety of factors that can affect the use and application of an Alumilite product, it is the user s obligation to determine the suitability of the product for its intended application, and user assumes all risk and liability for safe use of the product. Alumilite's liability is limited to product replacement only after review/testing of product alleged to be defective that is returned to Alumilite in accordance with Alumilite s Shipping and Returns Policy. In no event shall Alumilite be liable for punitive, consequential or indirect damages or damages in excess of the purchase price of the product. May 4, 2018 Alumilite Flex 30, 40, 60, 70 and 80 A Side Page 4 of 4 67318-020303 A
Product: CAS #: Product Use: Manufacturer/Supplier: Company Name: Company Address: Section 1 - Product and Company Identification Alumilite Flex 30, 40, 60, 70, and 80 B Side Non-Applicable Mold Making and Casting Alumilite 315 E. North St. Kalamazoo, MI 49007 Telephone Number: 269-488-4000 Emergency Telephone: Chemtrec 1-800-424-9300 Section 2 - Hazards Identification 2.1 Classification of the substance or mixture GHS Classification in accordance with 29 CFR 1910 (OSHA HCS) Acute toxicity, Inhalation Category 4 Skin irritation Category 2 Eye irritation Category 2A Respiratory sensitization Category 1 Skin sensitization Category 1 Specific target organ toxicity Single exposure respiratory system. Category 3 For the full text of the H-Statements mentioned in this Section, see Section 16. 2.2 GHS Signal Word, Hazard Statement, Symbol Pictograms by CLP/GHS: Signal Word: Danger Hazard Statements: A: Causes eye, skin irritation. Harmful if swallowed. May cause respiratory irritation. Precautionary Statements: B: Do not breathe dust/fume/gas/mist. Wash skin thoroughly after handling. Do not handle until all safety precautions have been read and understood. 2.3 Hazards not otherwise classified (HNOC) or not covered by GHS Harmful if swallowed. May cause skin irritation. May cause respiratory irritation. Alumilite Flex 30, 40, 60, 70 and 80 B Side Page 1 of 4 67318-020303 B
Section 3 - Composition / Information on Ingredients CAS No. Percentage Aromatic Isocyanate 101-68-8 30-70% Plasticizer 6846-50-0 30-70% Section 4 - First Aid Eye Contact: Skin Contact: Inhalation: Ingestion: In case of eye contact, immediately flush with plenty of water for up to 15 minutes. Remove any contact lenses and open eyes wide apart. Get medical attention if irritation develops or persists. In case of skin contact with contents of product, remove contaminated clothing and wash skin with soap and water. Get medical attention if irritation develops. Remove the affected person into fresh air. Assist in breathing if necessary. Drink large quantities of water if accidentally ingested. Get medical attention if any discomfort continues. Do not induce vomiting. Section 5 - Fire Fighting Measures Extinguishing Media: Water. Foam. Dry powder. Carbon dioxide (CO2). Fire Fighting Instructions: Treat as a class B fire. Flash Point: Side B: Not known Section 6 - Accidental Release Measures General: Waste Disposal: Extinguish all ignition sources. Avoid sparks, flames, heat and smoking. Ventilate. Avoid inhalation of vapors and contact with skin and eyes. Wear suitable protective clothing. See Section 8 of the MSDS for Personal Protective Equipment. Do not allow to enter drains, sewer or water course. Section 7 - Handling and Storage General: Storage: Wash thoroughly after handling. Remove contaminated clothing and wash before reuse. Avoid contact with eyes. Avoid ingestion and inhalation. Store in a cool, dry place. Keep container closed when not in use. Section 8 - Exposure Controls & Personal Protection Clothing: Eyes: Respiration: Ventilation: Wear chemical goggles. B Side Appearance: Liquid Color: Clear Odor: Mild ph: Not Known Boiling Point/Range: 200 C Melting Point/Range: Not known Section 9 - Physical & Chemical Properties Alumilite Flex 30, 40, 60, 70 and 80 B Side Page 2 of 4 67318-020303 B
Section 10 - Stability & Reactivity Chemical Stability: Stable Conditions To Avoid: Avoid excess heat and source of source of ignition. Incompatible Materials: Avoid contact with moisture. Keep away from strong base and acid. Hazardous Decomposition Products: At thermal decomposition temperature, carbon monoxide and carbon dioxide. Section 11 - Toxicological Information Toxicity Data Acute Toxicity: Inhalation: Skin Contact: Eye Contact: Ingestion: Chronic Toxicity: B Side No information about product s acute. toxicity available. LD50>25,000mg/kg May cause chemical asthma. May cause skin irritation. May cause eye irritation. Not known. (May be fatal) May cause chemical asthma. Section 12 - Ecological Information (Non Mandatory) Bioaccumulation: Ecotoxicity Effects: Mobility: Section 13 - Disposal Information (Non Mandatory) Disposal Instructions: Contaminated Packaging: Dispose of waste and residues in accordance with local authority requirements. Since emptied containers may retain product residue, follow label warnings even after container is emptied. Section 14 - Transportation Information (Non Mandatory) DOT (US) UN Number: 3335 Class: 9 Packing Group: III Section 15 - Regulatory Information (Non Mandatory) Under the criteria of the Federal OSHA Hazardous Communication Standard 29 CFR 1910.1200 Symbols, R/S Phrases: No data available. Hazardous Health Rating: Health: 2 Fire: 1 Reactivity: 1 Alumilite Flex 30, 40, 60, 70 and 80 B Side Page 3 of 4 67318-020303 B
No data available In accordance with Occupational Safety and Health Act (1970), Section 16 Other Information The information contained in this Safety Data Sheet is to the best of Alumilite's knowledge and belief, accurate and reliable as of the date compiled. However, no representation, warranty or guarantee is made as to its accuracy, reliability or completeness. NO WARRANTY OF MERCHANTABILITY, FITNESS FOR ANY PARTICULAR PURPOSE OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, IS MADE CONCERNING THE INFORMATION HEREIN PROVIDED OR ANY RELATED PRODUCT. User is responsible for determining whether the Alumilite product is fit for user's particular purpose and suitable for user's use or application. Given the variety of factors that can affect the use and application of an Alumilite product, it is the user s obligation to determine the suitability of the product for its intended application, and user assumes all risk and liability for safe use of the product. Alumilite's liability is limited to product replacement only after review/testing of product alleged to be defective that is returned to Alumilite in accordance with Alumilite s Shipping and Returns Policy. In no event shall Alumilite be liable for punitive, consequential or indirect damages or damages in excess of the purchase price of the product. May 4, 2018 Alumilite Flex 30, 40, 60, 70 and 80 B Side Page 4 of 4 67318-020303 B