x. ANNUAL REVIEW SIGNATURE SHEET

Similar documents
Bloodborne Pathogens Exposure Control Plan. December 2003

Biological Safety Training

BSL-2 Emergency Plan

FLORIDA GULF COAST UNIVERSITY DEPARTMENT OF REHABILITATION SCIENCES BIOSAFETY AND INFECTIOUS AGENTS CONTROL PLAN

Provide a brief description of the procedure and infectious organisms used:

COALINGA STATE HOSPITAL NURSING POLICY AND PROCEDURE MANUAL SECTION Infection Control POLICY NUMBER: 860. Effective Date: August 31, 2006

Infection Control 101

UNIVERSITY OF NORTH FLORIDA BIOMEDICAL WASTE MANAGEMENT PLAN DEVELOPED BY: ENVIRONMENTAL HEALTH, SAFETY, INSURANCE & RISK MANAGEMENT

MEDICAL WASTE MANAGEMENT

Bloodborne Pathogens Exposure Control Plan

OSHA: Occupational Safety and Health Administration PPE Personal protective equipment

Enhanced BSL2 (BSL2+) Lab Policy IBC Policy # Approved: 10/3/18

Laboratory Orientation. Biological Screening

List any references used for the procedure design (research publications, etc.):

Roosevelt Biosafety Training. Created 10/2015

Deadly Bloodborne Diseases

State of Kuwait Ministry of Health Infection Control Directorate SAFE INJECTION

Biohazardous Waste. 1. Solid Biohazardous Waste (non-sharps) Storage

San Bernardino Valley College. Blood Borne Pathogens. Exposure Control Program

Standard Operating Procedure for Blood Borne Infectious Disease Control Measures at Calvin College

The following standard practices, safety equipment, and facility requirements apply to BSL-1:

Michigan State University Athletic Training Students BLOOD BORNE PATHOGENS AND UNIVERSAL PRECAUTIONS

Handling and Disposing of Needles

Brazosport College Life Science Laboratory Safety Rules and Regulations

TEMPLE UNIVERSITY - Research Administration Institutional Biosafety Committee

Regulated Medical Waste. Be sure to sign in!

A ppendix 15 WUStL Bloodborne Pathogens Exposure Control Plan Research Laboratory-Specific Work Practices

Annual Associate Safety Module. Blood & Body Fluids: How To Prevent Exposure Your Exposure Control Plan

Safety Office -- Laboratory Inspection Form

STANDARD: Laboratory Safety Effective: March 20, 2018

What is infection control?

Bloodborne Pathogens

Standard Microbiological Practices: Basic Biosafety Principles & Lab Hygiene

General Lab Safety Rules and Practices SOP-GLSRP-01

University Of Florida. Bloodborne Pathogen Program. Standard Operating Procedures

Emergency Procedures Specific Biological Spill Clean-Up Guidelines

Bloodborne Pathogens Exposure Control Plan

BSL2 Exposure Control Plan: Human or Non Human Primate Materials

Disposal of Biological Waste

TEN EASY STEPS FOR CLEANING A SPILL IN THE BIOSAFETY CABINET

Biosafety Self-Audit Checklist

Case Western Reserve University Department of Environmental Health & Safety

Bloodborne Pathogens: Exposure In The Workplace Employee Handbook

Self-Inspection 2018 Biosafety Containment Level 2 Requirements To be verified at an Inspection by Biohazard Committee Members

ECU Radiation, Biosafety and Hazardous Substances Committee

Safety Rules for Laboratory

Appendix C. Infectious Waste Guidelines

Working at Biosafety Level 2 (BSL-2)

Updated by S. McNew, March Deborah Jung Microbiology Preparation Technician

METHODS OF IMPLEMENTATION AND CONTROL

The Aim Of Biosafety Training Is To Increase Your Ability To Recognize And Reduce Hazards In a BSL1 Lab

Standard Operating Procedure for Biosafety Cabinet Use

INFECTION PREVENTION AND CONTROL PLAN

Package Leaks. OH&S Biosafety Emergency Response Document. Examine outer packaging. Leaks or evidence of leaks. No evidence of leaks

Original Date:

Emergency Response and Biohazard Exposure Control Plan IBC Approved: 10/3/18

Cleaning and Disinfection Protocol for Emergency Services Fire, Ambulance, Police, Search & Rescue

SKIDMORE COLLEGE. Biohazardous Waste Management Policy and Exposure Control Plan TABLE OF CONTENTS. Introduction -- Pg. 2

BIOLOGICAL SAFETY INSPECTION CHECKLIST

Standard Operating Procedures

The Management of Inoculation (Sharps) Injury or Blood Borne Pathogen Exposure Policy

Bloodborne Pathogens Safety in Your Workplace

Sterilization A Training Module

SOP BIO-002 FOR SHARPS USAGE AND DISPOSAL

Safe Handling and Disposal of Sharps. Reference Guide

PUBLIC HEALTH DEPARTMENT

LAB 5 Blood Collection

CLEANING, SANITIZING, AND DISINFECTING

SHARPS MANAGEMENT AND DISPOSAL OF SHARPS, SYRINGES & CONTAMINATED PRODUCTS

BLOODBORNE PATHOGENS

Procedure 30 Collecting A Blood Specimen Using The Vacuum-Tube System. Procedure 31 Collecting A Blood Specimen Using A Needle And Syringe

UNIVERSITY OF SOUTHERN MAINE Office of Research Integrity & Outreach

ILLINOIS STATE UNIVERSITY BLOODBORNE PATHOGENS EXPOSURE CONTROL PLAN

Environmental Health Department 58 St Johns Road, Newport, Isle of Wight PO30 1LT

VGH Laboratory Guidelines Positive blood cultures from patients with suspect Ebola Virus Disease or other Viral Hemorrhagic Fevers

Disposal of Biohazard Wastes

REQUEST FOR QUOTE. Community Initiatives Bureau. Biohazardous Cleaning Service

CCS Administrative Procedure T Biosafety for Laboratory Settings

Table 5: Detailed Infection Prevention and Control Procedures for Body Piercing. drape the piercing site.

Student Performance Guide. Student Performance Guide. Student Performance Guide. Student Performance Guide. LESSON 3-3 Bleeding Time

Table 6: Detailed Infection Prevention and Control Procedures for Tattooing and Micropigmentation. Use During Tattooing

Hand Hygiene & PPE Policy

INFECTION PREVENTION AND CONTROL PLAN (IPCP)

rooo.lb IOWA COUNTY ORDINANCE NO TATTOO ARTIST REGULATIONS THE IOWA COUNTY BOARD OF SUPERVISORS DO ORDAIN AS FOLLOWS:

NATIONAL ELECTROLOGY PRACTICAL EXAMINATION CANDIDATE INFORMATION BULLETIN

LYMPHOCYTE ISOLATION

Cherie Maguire, MS Research Assistant II Channing Division of Network Medicine. The Center for Clinical Investigation

Standard Operating Procedures

Biohazard Waste Management Plan

Surgical Gown. Tongue Depressor. A disposable gown worn by medical staff during surgery. A thin, flat, wooden stick rounded at both ends

TATTOOING, BODY PIERCING, PERMANENT COSMETICS & BRANDING APPLICATION FOR REGISTRATION

Building/Lab Room No(s): Biosafety Containment level: BSL Click here to enter text.

Safe Sharps Disposal. Learn how to safely dispose of used sharps including needles, lancets and syringes. Expanded Syringe Access Program

BODY ART FACILITY INFECTION PREVENTION AND CONTROL PLAN

Hand Hygiene. Policy Title: Hand Hygiene Policy Number: 05. Effective Date: 6/10/2013 Review Date: 6/10/2016

Body Art Facility Infection Prevention And Control Plan Guideline

SUTTER COUNTY DEVELOPMENT SERVICES DEPARTMENT

BIOLOGICAL SAFETY MANUAL

TARLETON STATE UNIVERSITY Biohazardous Waste Program

Hygienic requirements for tattoo and piercing studios

Transcription:

x. ANNUAL REVIEW SIGNATURE SHEET PROCEDURE TITLE: UNIVERSAL PRECAUTIONS Signature on this page insures that each procedure has been reviewed annually. Any changes will be reflected on the procedure by the revised date. Medical Director Signature/Date:

L,; :"w"r/' <;~~~ _~,,*);,~:J:\:'i~}"c~.if:,2';~~~:;'~'?j,f''':,\~ :,: S'"~~:-J::;3; ::. ;~_~~, ~j'<t{; :"2r""..;, -;_~~~":; : - 1\~ 1" tas~~s ;, whi,c ti:, il~tpl:iide ' -rem.6ya~1. -or~, recapp:i ng ~i~':~} ' ~~~ :,: of ~ a -' needl'e.. from a '_ syringe', ejt adapto'r ar_e <:,}hi,!:,,;';/l~? ~fl~f~jii~iflf:~ ~tii~~i~~~i~~i~!~1t~,~tt~~&fr< UNIVERSAL PRECAUTIONS It is the policy of University Hospital that all employees will utilize Universal Precautions U.P.) principles of infection control in their periormance of direct and indirect patient care. 1 All laboratory workers will follow the hospital policy PI-12 on universal precautions see attached to this policy) and, in addition, will follow the specific recommendations outlined below. It is the responsibility of each supervisor to provide training for employees on U.P. procedures. It is the responsibility of each employee to practice U.P. at all times. See also lab safety policy P-1 0, Personal Protective Equipment. A. Agenda to Hospital Policy PI-12 1. Hand Washing 2 Hands should be washed whenever there is visible contamination with blood or body fluids, after completion of work, and before leaving the laboratory, after removing gloves, before eating, drinking, smoking, applying makeup, changing contact lenses, and using lavatory facilities, and before any and all other activities which involve contact touching) of the hand with mucous membranes, eyes, or breaks in the skin. If contact of blood, body fluids, or tissue occurs because of a break hole or tear) in the glove, the gloves should be immediately removed and the hands thoroughly washed. Washing with soap and water is recommended. No additional benefit has been established for routine washing with antiseptic soaps or antiseptics 2 Use of a moisturizing hand cream after washing may reduce skin irritation caused by frequent hand washing. A hand washing sink should be designated in each laboratory work area. It should be separate from sinks used for washing equipment or for waste disposal. 2 2. Needles and Sharps2 a. All tasks in which needles or sharps are used pose a risk to the health care worker. Specific operating procedures for their use are outlined in the department procedure manuals. b. The use of needles in the laboratory is discouraged except for phlebotomy or when no other alternative is feasible. Although the recapping and removal of needles is also strongly discouraged, there are certain procedures periormed in the laboratory for which recapping of the needle or removal of the needle is unavoidable. Any task in which a needle must be removed or recapped is considered a high-risk task, and special precautions must be taken. Other tasks in which there is significant manipulation of needles are also of particular risk.

r, c. High risk tasks include Handling Procedure Removal of vacutainer needles from adaptor Removal of uncapped needle from syringe Use one-handed technique to place needle into the needle jig on the sharps container. Unscrew the adaptor and let needle drop into sharps container. DO NOT pick up sharps container in other hand to perform this task. Use one-handed technique to place needle into the needle jig on the sharps container. Unscrew the syringe and let needle drop into sharps container. Alternatively, use one-handed technique to re-cap needle. Use pliers to brace the capped needle and slowly twist off the syringe with the other hand. Capping a syringe needle Removal of capped needle from syringe Use one-handed technique to slide needle into cap. Then use second hand to tighten cap. Whenever possible, use pliers to brace the capped needle and twist off the syringe with the other hand. If situation is such that pliers cannot be used, hold capped needle in one hand and slowly twist the syringe away from the needle with the other hand. DO NOT let the needle slide out of the cap. Transfer of blood specimen from a syringe to an evacuated tube Puncture the diaphragm of the rubber stopper and allow the correct amount of fluid. The vial should not

be hand held when puncturing the top. Handling butterfly adapters Handle by wings only and dispose of directly into a sharps container. Do not attempt to remove a vacutainer adaptor from a butterfly. 3. Protective Barriers A. Gloves Latex or vinyl gloves must be worn for all procedures involving capillary puncture, phlebotomy, and arterial and bone marrow specimen collection. Latex or vinyl gloves must be worn 2 by all personnel who handle or process tissues, blood, serum, plasma, cerebrospinal fluid, vaginal secretions, semen, bronchopulmonary washings, synovial fluid, peritoneal fluid, pleural fluid, amniotic fluid, pericardial fluid, or any other bodily material visibly contaminated with blood. Since saliva and breast mild contain low concentrations of HBV and HIV in the absence of visible blood contamination, gloves are recommended when handling specimens of saliva, sputum, and breast milk. 2 'I ) Latex or vinyl gloves should be worn when handling items that are likely to be contaminated,2 including biological safety cabinets, laboratory instruments, specimen containers, counter tops, computer keyboards, and telephones. These items should all be considered contaminated if in the laboratory setting, so hand washing is recommended before leaving the area. Latex or vinyl gloves must be worn when handling biohazard bagged material and visibly contaminated items or linen 2 and also for biohazard spill cleanup. Latex or vinyl gloves are available to all employees for use. If any employee experiences allergies to a particular glove product, a reasonable effort will be made to find glove liners or a non-allergenic product for the employee to wear. Gloves should be changed if they accidently become visibly contaminated with blood or body fluids, if physical damage tears or holes) occurs, or if chemical damage e.g., from organic solvents) occurs. b. Gowns Long laboratory coats must be worn when handling specimens. Lab coats must be buttoned. If the laboratory coats cannot be buttoned, an apron or gown must be worn. Laboratory coats used during open specimen handling or testing cannot be worn outside the laboratory area or for phlebotomy. Unsoiled laboratory coats used during phlebotomy may be used while working in the laboratory. If laboratory coats are worn in non-clinical areas of the institution, coats must not have been in use for specimen handling or testing or for phlebotomy. Laboratory coats are

r not required in non-clinical areas. If infectious material is spilled on a laboratory coat, remove promptly, place in a red bag, and place bag in the lab laundry hamper. Lab coats may not be taken home and laundered by the lab employee. If infectious material is spilled on personal clothing, remove clothing as soon as possible. The personal clothing must be decontaminated before the employee can take it home. The use of an anti-viral agent such as Virex is recommended in a warm water soak. Once decontaminated, personal clothing can be taken home and cleaned with household laundry detergent. Gowns or aprons made of impervious materials, e.g., plastic-paper alloys, should be worn during procedures known or suspected to result in splashing of body fluids. c. Masks, Eyewear Masks and protective eyewear or face shields must be worn for blending, sonicating, vigorous mixing, and when removing tightly impacted stoppers from tubes - or in any other situation where the health care worker anticipates mucous membrane contamination. d. Occlusive Dressings All skin defects e.g., exudative lesions, dermatitis, cuts, or abrasions) located on parts of the body exposed to blood or body fluid should be covered with a waterimpermeable occlusive bandage or otherwise shielded. This includes defects on the arms, face, and neck. 2 4. Mouth to Mouth Resuscitation - no additions to hospital policy. 5. Employee Specifics a. Smoking, eating, and drinking are not allowed in the laboratory area. Contact lenses should not be inserted or removed in the laboratory area. Application of cosmetics, lip balm, etc., is not allowed in the laboratory area. b. Fingers, pencils, and other objects used in the laboratory must be kept away from the mouth and/or mucous membranes. c. Employees failing to comply with safety practices or who endanger the safety of other employees, patients, or visitors will receive a corrective action. Employees who do not immediately correct their actions will receive a disciplinary action, which may result in loss of payor dismissal. 6. Environmental b. Spills continued)

Wear gloves and a gown to clean all spills. If the spill contains broken glass or other objects, these should be removed without contact with the hands. Rigid sheets of cardboard used as a 'pusher' and "receiver" may be used to handle such objects and then discarded into the biohazard waste container. In a centrifuge, a forceps with gauze can be used to remove bits of glass. If the spill is large and/or there is potential of contaminating the workers' shoes, waterimpermeable shoe covers should be worn. r Absorb the spill with disposable absorbent material e.g., paper towel, gauze pads, or tissue wipes). Note - the spill cannot be adequately disinfected unless the bulk of it is absorbed and picked up first. Clean the spill site of all visible spilled material using an aqueous detergent solution. Absorb the liquid. Disinfect the spill site using an appropriate intermediate to high-level hospital disinfectant, e.g., 1:10 bleach. Flood the spill site or wipe down the spill site until it is "glistening wet.' Let bleach site on the site for a minimum of 2 minutes. For other disinfectants, follow manufacturer's directions.) Absorb the disinfectant solution with disposable material. Rinse with water to remove any noxious chemicals or odors. Dry the site. Dispose of solid materials in a biohazard waste container. Use an intermediate rigid container if the spill contained sharps. Large quantities of liquid can be disposed of in a san itary sewer. f. Pipetting g. Mouth pipetting is not allowed. All pipetting must be performed using a rubber bulb or mechanical device. Centrifugation All specimens must be capped during centrifugation and contained within aerosol

r protection/containment cups or a closed rotor. The centrifuge lid or rotor should not be opened wh ile the centrifuge is running. h. Biohazard Containers Sharps contains, small waste containers, and biohazard waste boxes must be provide in all work areas. i. Specimen Analysis All testing procedures in which U.P. fluids are assayed must include the use of protective barriers appropriate to the tasks. j. Disinfecting Work Areas/Equipment Work surfaces should be cleaned and disinfected at the end of each work shift. Equipment should be cleaned and decontaminated prior to being repaired or transported to a contracted repair service. k. Food Storage r Food may be stored in a designated refrigerator or in a designated office area. A designated refrigerator must contain a prominent sign on the outside stating "Store only food in this refrigerator." Refrigerators not designated for food must contain a prominent sign on the outside stating "Do not store food in this refrigerator." A designated office area is one which has been identified as a clean area and in which no gloves or contaminated lab coats are worn. 7. Specimen Handling a. Requisitions and Specimen Containers Requisitions or specimen containers contaminated with blood or body fluids should be placed in a bag labeled biohazardous or red and the originating nursing unit called to clean the container with approved disinfectant and to replace the lab requisition form. If a representative from the originating unit does not clean the requisition and container within 15 minutes, the plastic bag should be returned to the unit The lab will not accept or process specimens with exposed needles. The lab will not accept urine or fluids in paper containers. The primary specimen container for all specimens must be leakproof. For U.P. fluids, each specimen must be placed inside a secondary container for transport. The secondary container can be a plastic bag, a secondary test tube, or a test tube rack in a plastic tub or phlebotomy tray.

b. Retumed units of blood must be in a secondary container, e.g., a plastic bag. Specimen Handling All specimens should be covered, capped, corked, or plugged except while being separated, poured, or during analysis. To remove a rubber stopper from a tube, use plastic coated gauze to cover the stopper or work behind an acrylic splash shield. All microbiology specimens should be opened in a biosafety hood. All containers of bronchopulmonary washings or sputum should be handled as if they are contaminated on the outside. 2 B. Hepatitis Immunization Hepatitis B vaccine is available to all employees of the clinical laboratory through University Hospital Health Services. The vaccine will be offered to all employees on employment see UH policy HH-7) but may be received at any point in employment. C. Accident Reporting References See lab policy on accident reporting and hospital policy on blood exposure UH Policy HB-1). 1. Infection Control/Universal Precautions, UH Policy PI-12, Oct. 30, 1991. 2. Protection of laboratory Workers from Infectious Disease Transmitted by Blood, Body Fluids, and Tissue, 2nd Ed., NCClS Document M29-T2, Vol. 11, No. 14, 1991.

,. \ 1 2 Attachments Infection Control/Universal Precautions, UH Policy PI-12, Oct. 30, 1991. This policy must be followed in addition to the laboratory policy above. NCClS Document M29-T2: Protection of laboratory Workers, p. 1-5. This information on the epidemiology, transmission of human hepatitis viruses and retroviruses, and survival of HIV, is required reading for all laboratory workers who fall under universal precautions.