ROYAL CELLULAR PVC ADHESIVE is a permanent, structural, two-component adhesive formulated for installing and fabricating Royal cellular PVC. SC allows an extended work life of 20-25 minutes at 75 F after mixing. It should be used for bonding any intersection of PVC where possible separation is a concern or additional integrity is required without the need for additional fasteners or biscuits. SC will fill gaps up to 1/4 A proper joint is stronger than the surrounding PVC after fully curing. SC is also ideal to fill and seal countersunk screw and nail holes. It is EPA VOC s and CARB compliant and it resists yellowing. It is completely paintable. SC will also bond most plastics, aluminum, steel, and fiberglass. for resealing. Replace cap with a ROYAL Quick Mixer Tip. Fill tip and apply as needed. Press parts together and clamp or fixture in place. Excessive force is not required. Clean excess adhesive quickly with a putty knife and/or rubbing alcohol. Joints may be handled in 90-120 minutes. Remove cartridge from gun, remove ROYAL Quick Mixer Tip, wipe tip with a clean cloth, making sure not to mix adhesive and catalyst. Strike the end of the cartridge on a hard surface so plungers back up slightly. Seal with original cap using aligning marks. Product should only be applied above 40 F. 20-25 MINUTE WORK TIME Contents: 50 ML DANGER! FLAMMABLE LIQUID. DO NOT USE NEAR FIRE OR FLAME. USE IN WELL VENTILATED AREA. HARMFUL IF SWALLOWED. MAY CAUSE EYE AND SKIN IRRITATION. READ MSDS BEFORE USE. NOTICE TO PURCHASER LIMITATION OF LIABILITY: Royal Building Products disclaims liability for any dangers and bodily injury resulting from failure to heed warnings on the label and is beyond the control of Royal Building Products. Royal Building Products shall not be responsible for damages resulting from the use of this product. Manufacturer s warranty is limited to replacement of products or refund of purchase price on goods proven defective.
ROYAL CELLULAR PVC ADHESIVE is a permanent, structural, two-component adhesive formulated for installing and fabricating Royal cellular PVC. FC allows a work life of 4-6 minutes at 75 F after mixing. It should be used for bonding any intersection of PVC where possible separation is a concern or additional integrity is required without the need for additional fasteners or biscuits. FC will fill gaps up to 1/8. A proper joint is stronger than the surrounding PVC after fully curing. FC is also ideal to fill and seal countersunk screw and nail holes. It is EPA VOC s and CARB compliant and it resists yellowing. It is completely paintable. FC will also bond most plastics, aluminum, steel, and fiberglass. for resealing. Replace cap with a ROYAL Quick Mixer Tip. Fill tip and apply as needed. Press parts together and clamp or fixture in place. Excessive force is not required. Clean excess adhesive quickly with a putty knife and/or rubbing alcohol. Joints may be handled in 20-30 minutes. Remove cartridge from gun, remove ROYAL Quick Mixer Tip, wipe tip with a clean cloth, making sure not to mix adhesive and catalyst. Strike the end of the cartridge on a hard surface so plungers back up slightly. Seal with original cap using aligning marks. Product may be applied at 28 F or above. 4-6 MINUTE WORK TIME Contents: 50 ML DANGER! FLAMMABLE LIQUID. DO NOT USE NEAR FIRE OR FLAME. USE IN WELL VENTILATED AREA. HARMFUL IF SWALLOWED. MAY CAUSE EYE AND SKIN IRRITATION. READ MSDS BEFORE USE. NOTICE TO PURCHASER LIMITATION OF LIABILITY: Royal Building Products disclaims liability for any dangers and bodily injury resulting from failure to heed warnings on the label and is beyond the control of Royal Building Products. Royal Building Products shall not be responsible for damages resulting from the use of this product. Manufacturer s warranty is limited to replacement of products or refund of purchase price on goods proven defective.
ROYAL CELLULAR PVC ADHESIVE is a permanent, structural, two-component adhesive formulated for installing and fabricating Royal cellular PVC. SC allows an extended work life of 20-25 minutes at 75 F after mixing. It should be used for bonding any intersection of PVC where possible separation is a concern or additional integrity is required without the need for additional fasteners or biscuits. SC will fill gaps up to 1/4 A proper joint is stronger than the surrounding PVC after fully curing. SC is also ideal to fill and seal countersunk screw and nail holes. It is EPA VOC s and CARB compliant and it resists yellowing. It is completely paintable. SC will also bond most plastics, aluminum, steel, and fiberglass. for resealing. Replace cap with a ROYAL Quick Mixer Tip. Fill tip and apply as needed. Press parts together and clamp or fixture in place. Excessive force is not required. Clean excess adhesive quickly with a putty knife and/or rubbing alcohol. Joints may be handled in 90-120 minutes. Remove cartridge from gun, remove ROYAL Quick Mixer Tip, wipe tip with a clean cloth, making sure not to mix adhesive and catalyst. Strike the end of the cartridge on a hard surface so plungers back up slightly. Seal with original cap using aligning marks. Product should only be applied above 40 F. 20-25 MINUTE WORK TIME Contents: 220 ML DANGER! FLAMMABLE LIQUID. DO NOT USE NEAR FIRE OR FLAME. USE IN WELL VENTILATED AREA. HARMFUL IF SWALLOWED. MAY CAUSE EYE AND SKIN IRRITATION. READ MSDS BEFORE USE. NOTICE TO PURCHASER LIMITATION OF LIABILITY: Royal Building Products disclaims liability for any dangers and bodily injury resulting from failure to heed warnings on the label and is beyond the control of Royal Building Products. Royal Building Products shall not be responsible for damages resulting from the use of this product. Manufacturer s warranty is limited to replacement of products or refund of purchase price on goods proven defective.
ROYAL CELLULAR PVC ADHESIVE is a permanent, structural, two-component adhesive formulated for installing and fabricating Royal cellular PVC. FC allows a work life of 4-6 minutes at 75 F after mixing. It should be used for bonding any intersection of PVC where possible separation is a concern or additional integrity is required without the need for additional fasteners or biscuits. FC will fill gaps up to 1/8. A proper joint is stronger than the surrounding PVC after fully curing. FC is also ideal to fill and seal countersunk screw and nail holes. It is EPA VOC s and CARB compliant and it resists yellowing. It is completely paintable. FC will also bond most plastics, aluminum, steel, and fiberglass. for resealing. Replace cap with a ROYAL Quick Mixer Tip. Fill tip and apply as needed. Press parts together and clamp or fixture in place. Excessive force is not required. Clean excess adhesive quickly with a putty knife and/or rubbing alcohol. Joints may be handled in 20-30 minutes. Remove cartridge from gun, remove ROYAL Quick Mixer Tip, wipe tip with a clean cloth, making sure not to mix adhesive and catalyst. Strike the end of the cartridge on a hard surface so plungers back up slightly. Seal with original cap using aligning marks. Product may be applied at 28 F or above. Contents: 220 ML 4-6 MINUTE WORK TIME DANGER! FLAMMABLE LIQUID. DO NOT USE NEAR FIRE OR FLAME. USE IN WELL VENTILATED AREA. HARMFUL IF SWALLOWED. MAY CAUSE EYE AND SKIN IRRITATION. READ MSDS BEFORE USE. NOTICE TO PURCHASER LIMITATION OF LIABILITY: Royal Building Products disclaims liability for any dangers and bodily injury resulting from failure to heed warnings on the label and is beyond the control of Royal Building Products. Royal Building Products shall not be responsible for damages resulting from the use of this product. Manufacturer s warranty is limited to replacement of products or refund of purchase price on goods proven defective.
FILL & FLEX Sealant/Adhesive Bonds to PVC trim, trimboard & moulding Paintable with acrylic latex-based paint Apply to wet or dry surfaces Remains flexible & UV stable Safe, non-flammable, non-solvent formulation WHITE, 10.0 fl. oz. (296 ml) Part number EXT-FF-300ML/PVC Fill & Flex is a premium one-component, proprietary, non-solvent, non-flammable, low VOC bonding sealant. Fill & Flex is designed for bonding to PVC trim, trimboards, and moulding. The advanced technology in Fill & Flex results in a product that will bond to wet or dry surfaces. Fill & Flex meets LEED and NAHB guidelines. Applications: For sealing and repairing exterior PVC trim, trimboards, and mouldings. Instructions: For best results, remove dust, dirt, and loose materials. Cut spout tip to desired bead size and puncture inner seal completely. Gun product into joint and tool immediately for best results. Clean excess, uncured material with a putty knife or disposable cloth. Use mineral spirits to clean hands and tools. Do not apply below 30⁰ F. Limited Warranty: We guarantee that this product is manufactured free of defects. If Fill & Flex fails to perform in accordance with its published literature, we, upon satisfactory evidence of product failure, will either refund the purchase price of or provide replacement for that portion of material that fails to perform in accordance with this warranty. Such refunds or replacements will constitute the limit of our liability and obligation for any such failure. Contents: Polymers (Proprietary), Fumed Silica (CAS# 112945-52-5), Adhesion Promoter (CAS# 11760-24-3), Titanium Dioxide (CAS# 13463-67-7) Volatile Organic Compounds (VOC): 34g/l or 3.2% by weight Chemically curing sealant or caulking compound.
Made in the USA CAUTION Extremely flammable. Vapor harmful. Keep out of reach of children. Keep away from flame or sparks. Do not swallow. May cause eye injury. Eye, skin and respiratory irritant. Cap tightly when not in use. Wear proper safety equipment. Understand the Material Safety Data Sheet for this product before use. Contains Tetrahydofuran, Methyl Ethyl Ketone, Cyclohexanone and PVC resin. Warranty is limited to replacement of product. First Aid: Inhalation: If inhaled move into fresh air. If not breathing give artificial respiration. Call a physician. Eye or skin contact: In case of eye or skin contact, flush with water for 15 minutes. If irritation persists, get medical attention. Ingestion: Give 1 to 2 glasses of water. Do not induce vomiting. Contact physician immediately. Thickened White Solvent Cement for PVC Trim WHITE HOT INSTRUCTIONS Apply a bead of adhesive to both parts to be bonded. Press the two parts together and allow to remain undisturbed until set. If only one part is accessible, apply a coat to that part, allow to set for 5 minutes and apply a second coat before assembly. Remove any excess WHITE HOT immediately since it will mar the surface of the PVC quickly. Not for use on metals or wood. Use Royal Cellular PVC Adhesive Fast Cure. Royal Building Products 135 Bear Creek Road Marion, VA 24354 800.368.3117 royalbuildingproducts.com Contents: 5 fl. oz.,