Brick and Masonry Brick and Masonry is an inhibited acid-based cleaner for the removal of cementand mortar residues. For light cleaning (cleaning of unhardened cement haze), dilute 1 part Brick and Masonry to 30 parts water. Coverage is approximately 60 m 2 per litre. For medium cleaning, dilute 1 part Brick and Masonry to 15 parts water. Coverage is approximately 30 m 2 per litre. For heavy cleaning (cleaning of hardened grout), dilute 1 part Brick and Masonry to 5 parts water. Coverage is approximately 10 m 2 per litre. Brick and Masonry is supplied in 1 and 5 litre packs. Suitable for use on clay face bricks, clay paving bricks, natural stone, slate, terracotta, glazedand unglazed ceramics. Also suitable for etching concrete floors prior to coating. Inhibited acid-based cleaner Does not attack and tarnish metal surfaces Removes oils and grease Caution Not for use on marble, travertine, limestone, cement tiles and pavers or terrazzo. Certain clay face bricks contain copper residues and could turn green with use of Brick and Masonry. Always test on a small area first. Ensure good ventilation and avoid breathing vapours. Avoid skin and eye contact. Wear safety glasses, gloves and protective clothing when necessary. Keep out of reach of children and pets and store away from other chemicals. Do not allow contact with other sensitive surfaces. Glazed and non-porous surfaces : do not pre-dampen. Porous surfaces : always pre-dampen the surface to prevent the acid from being absorbed too rapidly. Remove excess water prior to application of Brick and Masonry. Floors - apply Brick and Masonry by mop, sponge or plastic watering can. Walls - apply Brick and Masonry by spray, sponge or block-brush. Allow 15 minutes for Brick and Masonry to work, but do not allow stripper to dry out on the surface. Agitate with a nylon bristled brush or broom and then rinse well several times. If surfaces or tiles are to be sealed, ALWAYS neutralise the surface using Heavy Duty. Neutralising helps prevent sealer failure.
Ceramic and Porcelain Ceramic and Porcelain is a concentrated detergent cleaner formulated for gentle every day use. Dilute half a cup of Ceramic and Porcelain with 5 litres of warm water. Coverage is approximately 25 to 40m 2 per 5 litres. Ceramic and Porcelain is supplied in 1 and 5 litre packs. Suitable for use on glazed- and unglazed ceramics, polished- and unpolished porcelain tiles. Removes surface soiling and general dirt Eliminates soap build-up Reduces hard water deposits Avoid skin and eye contact. Wear safety glasses, gloves and protective clothing when necessary. Keep out of reach of children and pets and store away from other chemicals. Do not allow contact with other sensitive surfaces. Sweep the floor first to remove loose debris. Apply solution to floor using a clean mop or sponge squeegee. Agitate using a soft bristled broom to remove stubborn dirt and to clean grout lines. Remove dirty solution with a mop or sponge and squeegee into an empty bucket. This will prevent the dirty water from contaminating the cleaning solution.
Daily Cleaner Daily Cleaner is a concentrated multi-surface detergent cleaner formulated for gentle everyday use. For interior and exterior use. Dilute ¼ cup Daily Cleaner in 5 litres of warm water. Approximate coverage per 5 litre bucket should be between 25 and 40m 2. Daily Cleaner is supplied in 400ml, 1, 5 and 25 litre packs. Suitable for use on glazed- and unglazed ceramics, porcelain, granite, marble, travertine, sandstone, slate and all sealed surfaces including natural stone, terracotta, quarry tiles, vinyl and cement tiles. Removes surface soiling Eliminates soap build-up Reduces hard water deposits Avoid skin and eye contact. Wear safety glasses, gloves and protective clothing when necessary. Keep out of reach of children and pets and store away from other chemicals. Sweep floor to remove loose debris. Apply diluted Daily Cleaner by mop or sponge squeegee. Agitate using a soft bristle broom to remove stubborn dirt and clean grout lines. Remove dirty solution using a mop or sponge and squeeze into an empty bucket. This will prevent dirty water from contaminating the cleaning solution.
Grout Cleaner Grout Cleaner is a ready to use non-acidic cleaner for regular use on grout joints. For interior or exterior use. undiluted as supplied. Grout Cleaner is supplied in 500ml and 1 litre packs. Suitable for use on all grout joints. Removes grease and grime Removes mould and mildew Removes soap deposits and dirt Avoid skin and eye contact. Wear safety glasses, gloves and protective clothing when necessary. Keep out of reach of children and pets and store away from other chemicals. Turn nozzle to on position before use. Hold bottle 20 to 30cm away from the surface to be cleaned. Evenly and thoroughly spray the grout joint to be cleaned. Allow the product to work for at least 5 to 10 minutes before scrubbing with a red nylon pad or scrubbing brush. Rinse with clean water and dry using a clean cloth or sponge. For heavily soiled areas, allow the product to work for as long as possible without drying out.
Grout Residue Remover Grout Residue Remover is an inhibited acid-based cleaner for the removal of cement and grout residue. For light cleaning (cleaning of unhardened cement haze), dilute 1 part Grout Residue Remover to 30 parts water. Coverage is approximately 60 m 2 per litre. For medium cleaning, dilute 1 part Grout Residue Remover to 15 parts water. Coverage is approximately 30 m 2 per litre. For heavy cleaning (cleaning of hardened grout), dilute 1 part Grout Residue Remover to 5 parts water. Coverage is approximately 10 m 2 per litre. Grout Residue Remover is supplied in 1, 5 and 25 litre packs. Suitable for use on natural stone, slate, terracotta, bricks, porcelain, and glazed- and unglazed ceramics. Not for use on marble, travertine, limestone, cement tiles and pavers or terrazzo. Floors Apply diluted Grout Residue Remover by mop, sponge or plastic watering can. Allow 10-15 minutes for product to work. Do not allow to dry on the surface. Agitate using a nylon bristled brush or broom. Rinse well with clean water. Always neutralize the surface using Heavy Duty Cleaner to prevent sealer failure. Walls Apply diluted Grout Residue Remover by spray, sponge or block-brush. Allow 10-15 minutes for product to work. Do not allow to dry on the surface. Agitate using a nylon bristled brush or broom. Rinse several times with clean water. Always neutralize the surface using Heavy Duty Cleaner to prevent sealer failure. Removes cement and grout residue Inhibited acid prevents attack or tarnish to metal surfaces Contains detergents to remove oil and grease Caution Grout Residue Remover may cause certain natural products containing iron oxide to form rust. Always test first. Ensure good ventilation and avoid breathing vapours. Avoid skin and eye contact. Wear safety glasses, gloves and protective clothing when necessary. Keep out of reach of children and pets and store away from other chemicals. Do not allow contact with other sensitive surfaces.
Heavy Duty Cleaner Heavy Duty Cleaner is a concentrated heavy-duty degreasing cleaner and acid neutralizer for use in high traffic areas. For interior or exterior use. Light cleaning : dilute 1 part Heavy Duty Cleaner to 20 parts water. Coverage is approximately 60 m 2 per litre. Medium cleaning : dilute 1 part Heavy Duty Cleaner to 10 parts water. Coverage is approximately 40 m 2 per litre. Heavy cleaning : dilute 1 part Heavy Duty Cleaner to 5 parts water. Coverage is approximately 20 m 2 per litre. Heavy Duty Cleaner is supplied in 1, 5 and 25 litre packs. Suitable for use on natural stone, marble, granite, travertine, limestone, slate, terrazzo, terracotta, bricks, cement tiles, concrete floors, glazed and unglazed ceramics. Heavy Duty Cleaner cannot remove grout and cement residue or calcium deposits. Grout Residue Remover is specifically formulated to remove grout- and cement residue, calcium deposits and lime and is recommended for this purpose. Degreases Neutralises acid Suitable for heavy traffic areas Avoid skin and eye contact. Wear safety glasses, gloves and protective clothing when necessary. Keep out of reach of children and pets and store away from other chemicals. Floors Apply diluted Heavy Duty Cleaner by mop, sponge, plastic watering can or brush. Allow 10-15 minutes for Heavy Duty Cleaner to loosen the dirt. Scrub using a soft bristle broom, brush or floor scrubber. Remove residue using a clean mop, sponge or wet and dry vacuum. Rinse well with clean water. Walls Apply diluted Heavy Duty Cleaner by spray, sponge or block-brush. Allow 2 to 3 minutes for Heavy Duty Cleaner to loosen the dirt, but do not allow to dry on the surface. Agitate using a nylon bristled brush or broom. Rinse several times with clean water.
Mould Remover Mould Remover is a fast-acting cleaner for the removal of mould, mildew, black stains and algae. For interior or exterior use. undiluted as supplied. Mould Remover is supplied in 500ml and 5 litre packs. Suitable for interior use on ceramic, porcelain- and enamel surfaces, tiles and tile grout in bathrooms and showers. Suitable for exterior use on bricks, walls, paving, floor- and roof tiles. Removes mould and mildew Removes black stains and algae Cleans and disinfects Avoid skin and eye contact. Wear safety glasses, gloves and protective clothing when necessary. Keep out of reach of children and pets and store away from other chemicals. Do not mix with other chemicals. Do not allow contact with fabrics, clothing, pigmentsensitive paint and other sensitive surfaces. Hold sprayer 20 to 30cm from surface to be cleaned and spray evenly and thoroughly. Apply to ceilings or overhead areas by spraying onto a sponge first and then use the sponge to apply. Allow to react for at least 30 minutes. Re-apply to areas where mould or mildew remains if necessary. Scrubbing may be required in severe cases. Rinse well with clean water.
Rust Remover Rust Remover is an acid-based gel cleaner designed to remove red soil stains, rust, air- and carbon pollution, oxidisation, mould- and mildew stains. Safer than conventional acid-based cleaners. For light duty cleaning, dilute 1 part Rust Remover to 5 parts water. Coverage is approximately 12 m 2 per litre. For medium duty cleaning, dilute 1 part Rust Remover to 3 parts water. Coverage is approximately 8m 2 per litre. For heavy duty cleaning, dilute 1 part Rust Remover to 1 part water. Coverage is approximately 4m 2 per litre. Rust Remover is supplied in 1 and 5 litre packs. Suitable for use on unpolished and acid-resistant natural stone, unsealed concrete and masonry surfaces, terracotta- and quarry tiles. May be used on walls and floors. Not for use on polished- or acid-sensitive stone like marble, travertine and limestone. Acidbased products will etch and lighten most cement- and masonry surfaces. It is recommended that the surface be sealed after cleaning. Safer than conventional acid-based cleaners Removes red soil stains and rust Can be used on a range of surfaces Ensure good ventilation and avoid breathing vapours. Avoid skin and eye contact. Wear safety glasses, gloves and protective clothing when necessary. Keep out of reach of children and pets and store away from other chemicals. Do not allow contact with other sensitive surfaces. Do not pre-dampen glazed and non-porous surfaces. Pre-dampen porous surfaces to prevent the acid from being absorbed too quickly. Remove excess water prior to application. Floors : apply diluted Rust Remover by mop, soft bristle broom or brush. Walls : apply undiluted Rust Remover using a paint- or block-brush. Allow 10-30 minutes for the product to work, but do not allow to dry on the surface. Apply more product to keep the surface wet if required. Floors : use a standard speed buffing machine of 175-300 RPM with a brown/blue nylon pad or brush. Smaller areas may be scrubbed using a nylon pad, broom or brush. Walls : scrub using a nylon pad, broom or brush. Inspect the surface to ensure that the desired result has been achieved before rinsing with clean water. Rinse a second time if required. Always neutralize the surface using Heavy Duty Cleaner to prevent sealer failure. Remove all residue using a mop, sponge or wet and dry vacuum.
Stainless Steel Cleaner Stainless Steel Cleaner is a non-abrasive product that cleans, polishes and protects stainless steel, chrome and aluminium surfaces. undiluted as supplied. Stainless Steel Cleaner is supplied in a 300ml pack. Suitable for use on stainless steel fridges, appliances, toasters, kettles, work surfaces, decorative trim, aluminium and metal furniture. Not suitable for use on marble, granite, natural stone surfaces, plastics and plastic parts. Avoid over-application. Non-abrasive Cleans, polishes and protects Contains natural lemon extracts Caution Flammable. Do not store in direct sunlight or expose to temperatures above 50 0 C. Keep away from naked flames. Do not puncture or incinerate can. Avoid breathing vapours. Avoid contact with eyes. May cause skin irritation. Wear safety glasses, gloves and protective clothing when necessary. Do not spray on food or cooking utensils. Keep out of reach of children and pets. In case of ingestion, drink plenty of water and seek medical assistance at once. In case of contact with eyes, flush with clean water for at least 15 minutes and seek medical assistance at once. Always test on a small area first to determine suitability. Shake can well. Hold in an upright position about 15cm from the surface and spray lightly. Spread the cleaner using a damp cloth and then wipe dry using a soft, dry cloth or paper towel.
Ultra Clean Ultra Clean is a water-based, biodegradable, non-scratching abrasive cream cleaner. For interior or exterior use. Apply undiluted directly onto the surface to be cleaned. Coverage is approximately 10 to 40m 2 /litre depending on the texture of the surface and severity of soiling. Ultra Clean is supplied in 1 and 5 litre packs. Suitable for use on textured ceramics, polished- and unpolished porcelain tiles and natural stone. Ultra Clean cannot remove grout and cement residue. Grout Residue Remover is specifically formulated to remove grout- and cement residue, calcium deposits and lime on acid-resistant surfaces and is recommended for this purpose. Non-scratching, abrasive cream cleaner Biodegradable Removes factory applied waxes Avoid skin and eye contact. Wear safety glasses, gloves and protective clothing when necessary. Keep out of reach of children and pets and store away from other chemicals. Sweep or vacuum the surface to remove surface grit. Pre-wet the surface to be cleaned. Apply undiluted Ultra Clean. a standard speed buffing machine of 175-300 RPM with a red or blue nylon pad or scrub by hand using a red or blue nylon pad or brush. Rinse well with clean water. Remove residue using a clean mop, sponge or wet and dry vacuum. Rinse a second time if required.