1 NAFTA Refinishing Systems (English) 2 NAFTA Products

Transcription

1 1 NAFTA Refinishing Systems (English) 1-1 US National Rule for Automotive Refinishing 1-2 Bay Area Air Quality Management District - Rule San Diego County Air Pollution Control District, Rule / Mojave Desert Air Quality Management District - Rule 1116, 7/ South Coast Air Quality Management District - Rule 1151/ NAFTA Products 2-1 Surface Preparation Permahyd Silicone Remover Permahyd Silicone Remover Permanent Silicone Remover 7010 Slow 2-2 Primer / Primer Surfacer Permahyd 1K Primer Surfacer Permasolid 2.1 VHS Surfacer Permacron 2.1 Surfacer Permasolid HS Premium Surfacer Permacron Transparent Surfacer Permacron Vario Surfacer Permasolid Wet on Wet Surfacer Permasolid Spectro Surfacer Permacron 1:1 Elastic Primer Surfacer Priomat Elastic Primer 3304 Transparent Priomat 1K Primer Surfacer Permasolid EP Primer Surfacer Priomat Elastic Primer Priomat Wash Primer Priomat 5.5 Wash Primer Priomat Primer 3255 red brown 2-3 Top Coats Permacron Acrylic Urethane Series Permacron Base Coat Series Permacron Pearl Base Coat Series Permahyd Base Coat Series Permahyd Pearl Base Coat Series Permahyd Hi-TEC Base Coat Clear Coats Permacron 2.1 Clear Coat Permacron 2.1 Clear Coat Permasolid HS Diamond Clear Coat Permasolid HS Clear Coat Permasolid HS Clear Coat Permacron MS Clear Coat Permasolid HS Optimum Clear Coat Permacron Matte Clear Coat Additive Other Products Permahyd Sanding Paste Permahyd Stone Chip Protector Permahyd Additive Permahyd Special Water 6002 slow Raderal Spray Polyester Permacron Speed Blender 1036

2 Spies Hecker VOC Compliant Products for US National Rule for Automotive Refinishing (Mercedes Benz Approved Products) Edition: November 6, 2009 Also covers: Delaware- DNR Reg. 24 Sec 11; / Illinois-EPA Title 35, Admin. Code Part 218, Subpart HH / Indiana-D.E.M. Title 326 IAC 8-10/ Jefferson Co.-APCD Reg. 6.44/ Maricopa Co.APC Arizona, 345/ Massachusetts-Rule 310 CMR 7.28(28)/ Maryland-D.E.Comar / New Jersey AC 7: New York State Part 228 (Jan1, 05), Penn. DEP, Rule 121/ Portland-AQMA OAR / Rhode Island-APC Reg. No.30/ Tennesse-APCB Rule / Puget Sound-APCA Reg. 9.16/ Spokane Co.-APCA Reg. I Sec 6.13/ TCEQ 30 TAC Ch. 115/Vancover,WA-SWAPCA / Wisconsin-NRB Rule NR Product No Surface Preparation limits are set forth in the National Rule. Choose based upon more stringent VOC Limits as indicated. Supplied VOC lbs/gal Must use 7085 or 7090 for metal: Illinois, Indiana, Jefferson County-KY, Nashville-TN, Massachusetts, Maricopa Cnty (PHX area), Rhode Island, Puget Sound, Spokane, Texas, Wisconsin. Must use 7010/7799/7081 for cleaning of plastics (8581 is not allowed): Illinois, Indiana, Maryland, Rhode Island, Spokane, Wisconsin. Must use 7081 for cleaning of plastics (no other cleaners allowed): Jefferson Cty KY, Nashville TN, Maricopa Cty, Massachusetts, Texas. Supplied VOC g/l Permahyd Silicone Remover Permahyd Silicone Remover Permanent Silicone Remover 7010 Slow Permanal Silicone Remover 7799 Fast Priomat Plastic Reducer Permahyd Plastic Cleaning Paste Product Mix Ratio Hardener Reducer Highest Applied VOC LE (Less water-exempts) Pretreatment VOC Limit 6.5 lbs/gal (780 g/l) lbs/gal gms/ltr Priomat Wash Primer 4075 Gray 1: N/A Priomat 1K Primer Surfacer 4085 N/A N/A +50% , 3363, 3365, 3366 Priomat Primer 3255 Red Brown N/A N/A +50% , 3363, 3365, 3366 Primer/Primer Surfacer VOC Limit 4.8 lbs/gal (580 g/l) Regs with Precoat Limits apply in this category. Permahyd Primer Surfacer 4100 N/A N/A 0-10% Permasolid HS Premium Surfacer :1 3307, 3309, 3310, 3315, 3320, % , 3363, 3365, 3366 *Permasolid Spectro Surfacer :1 3307, 3309, 3310, 3315, 3320, % , 3363, 3365, 3366 *Permacron Vario Surfacer :1 3307, 3309, 3310, 3315, 3320, % , 3363, 3365, 3366 *8590 and 5400 may be mixed with 30% Elastic Additive 9050 with a resulting VOC of less than their original valu Primer Sealer VOC Limit 4.6 lbs/gal (550 g/l) Permahyd Stonechip Protector 7100 N/A % *Permsolid Spectro Surfacer :1 3307, 3309, 3310, 3315, 3320, % *Permacron Premium Surfacer :1 3307, 3309, 3310, 3315, 3320, % , 3363, 3365 * 8590 and 5400 may be mixed with 30% Permacro Elastic Additive 9050 with a resulting VOC of less than their original VOC Valu Single Stage Topcoat VOC Limit 5.0 lbs/gal (600 g/l) Permacron Acrylic Urethane Series 257 3:1 3307, 3309, 3310, 3315, 3320, % , 3363, 3365, 3366 Multistage System Option 1 Option 2 Permacron Base Coat Series 293/295 N/A N/A % +35% +15% 3054, 3055, Permacron Base Coat FP2002 N/A N/A % na 3054, 3055, 3056 Followed by: for 2-Stage 5.0 lbs/gal (600 g/l) BC+2*CC/3 Permacron MS Express Clear Coat :1 3307, 3309, 3310, 3315, 3320, % , 3363, 3365, 3366 Permacron MS Express Clear Coat :1 3220, 3230, % , 3363, 3365 Permacron MS Clear Coat :1 3307, 3309, 3310, 3315, 3320 N/A Permasolid HS Clear Coat :1 3307, 3309, 3310, 3315, 3320, % , 3363, 3365, 3366 Permasolid HS Clear Coat :1 3307, 3309, 3310, 3315, 3320, % Accelerator Permasolid HS Clear Coat :1 3307, 3309, 3310, 3315, 3320, % , 3363, 3365, 3366 Permacron MS Clear Coat :1 3307, 3309, 3310, 3315, 3320 N/A Permacron MS Clear Coat :1 3220, 3230, % , 3363, 3365 Permasolid HS Diamond Clear Coat : % , 3363, 3365, 3366 Permasolid HS Optimum Clear Coat :1 3220, 3230, 3240 N/A The above Clear Coats (not 8450) may be mixed with 15-30% Permacron Elastic Additive 9050 with a resulting VOC of less than their original VOC Value. Followed by: for 3-Stage 5.2 lbs/gal (630 g/l) (2*BC+2*CC)/4 Permacron HS Clear Coat :1 3307, 3309, 3310, 3315, 3320, 3325 N/A Permacron HS Clear Coat :1 3307, 3309, 3310, 3315, 3320, 3325 N/A Permasolid HS Diamond Clear Coat : N/A Permasolid HS Optimum Clear Coat :1 3220, 3230, 3240 N/A The above Clear Coats (not 8450) may be mixed with 15-30% Permacron Elastic Additive 9050 with a resulting VOC of less than their original VOC Value. GM 4901M Recommendations Multistage System VOC Limit 5.0 lbs/gal (600 g/l) Permacron Base Coat Series 293/ % 3307, 3309, 3310, 3315, 3320, % 3054, 3055, 3056 Followed by: "Approved" Clearcoats Permasolid HS Clear Coat :1 3307, 3309, 3310, 3315, 3320, % , 3363, 3365, 3366 Permacron MS Clear Coat :1 3307, 3309, 3310, 3315, 3320 N/A Permasolid HS Clear Coat :1 3307, 3309, 3310, 3315, 3320, % Accelerator Permacron HS Clear Coat :1 3307, 3309, 3310, 3315, 3320, % , 3363, 3365, 3366 Specialty Coating VOC Limit 7.0 lbs/gal (840 g/l) Adhesion Promoters Permacron Premium Surfacer :1 3307, 3309, 3310, 3315, 3320, % , 3363, 3365, 3366 Permacron Transparent Surfacer :1 3307, 3309, 3310, 3315, 3320, % , 3363, 3365 Uniform Finish Blenders Permacron Base Coat Blender 8560 Ready N/A N/A Permacron Speed Blender :1 Permacron Clear Coats (RTS) N/A Fisheye Eliminators Permacron Antisilicone ml:1 2K Acrylic Topcoats (RTS) N/A Elastomeric Coatings *Permacron Vario Surfacer :1 3307, 3309, 3310, 3315, 3320, % with 30% Permacron Elastic Additive , 3363, 3365, 3366 Permacron 1:1 Elastic Primer Surfacer 3300 Gray 1: N/A Permacron 1:1 Elastic Primer Surfacer 3300 Black 1: N/A Ralley Matt Black FP1004 3:1 3307, 3309, 3310, 3315, 3320, % , 3363, 3365, 3366 Priomat Elastic Primer 3304 Ready N/A N/A Permacron Semi-gloss Elastic Clear Coat :1 3307, 3309, 3310, 3315, 3320, % , 3363, 3365, 3366 Other Products Product Permahyd Sanding Paste 1120 Raderal Spray Polyester 3508 Gray Beige For specific VOC Topcoat recommendations and limts for Permahyd accounts, please contact Color Service at For jurisdiction, applicability, solvent handling, recordkeeping, exemptions, or for detailed information about local regulations, please contact Regulatory at Copyright 2009 DuPont. Spies Hecker, Permacron, Permasolid, Permanent, Permanal, Priomat and Permahyd are registered trademarks of E.I. du Pont de Nemours and Company for its brands of refinish systems. All rights reserved.

3 Spies Hecker V.O.C. Compliance Chart Bay Area Air Quality Management District Effective January 1, 2010 (Mercedes Benz Approved Products) Edition 03/08/2010 Surface Preparation lbs/gal (25 g/l) **Up to 5% (by vol.) of Permahyd Additive 9007 can be added to two-stage basecoats and the ground coat of three-stage formulas. As Supplied/Packaged VOC lbs/gal As Supplied/Packaged VOC g/l Product Mix Ratio Hardener Reducer Bay Area (LIMIT 0.2 lbs/gal - 25g/l) Permahyd Silicone Remover 7090 (limitations based on usage - LIMIT 350 g/l N/A N/A N/A Permahyd Silicone Remover 7085 (limitations based on usage - LIMIT 350 g/l N/A N/A N/A Permahyd Silicone Remover 7096 N/A N/A N/A Permahyd Plastic Cleaning Paste 7081 N/A N/A N/A Pretreatment VOC Limit 5.5 lbs/gal (660 g/l) Applied VOC LE lbs/gal Less Water & Applied VOC LE g/l Less Water & Product Mix Ratio Hardener Reducer Priomat 5.5 Wash Primer 4055 Gray N/A Priomat 1K Primer Surfacer 4085 (Spray Can) N/A N/A N/A EXEMPT Primer/Primer Surfacer VOC Limit 2.1 lbs/gal (250 g/l) Applied VOC LE lbs/gal Less Water & Applied VOC LE g/l Less Water & Product Mix Ratio Hardener Reducer Permahyd Primer Surfacer 4100 N/A N/A 0-10% Permacron 2.1 VHS Surfacer : % , 3363, 3365, 3366 Permasolid 2.1 Surfacer :1 3193, 3195, 3197, % , 3370, 3371 Permasolid 2.1 Surfacer 5155 with 30% Elastic Additive :1 3193, 3195, 3197, % , 3370, 3371 Primer Sealer VOC Limit 2.1 lbs/gal (250 g/l) (Effective 1/1/2010) Applied VOC LE lbs/gal Less Water & Applied VOC LE g/l Less Water & Product Mix Ratio Hardener Reducer Permahyd Stonechip Protector 7100 N/A N/A +0-10% Permasolid Non-Sanding Sealer 5156 Gray 2:1 3193, 3195, 3197, % % 3369, 3370, may be mixed with 15-30% Elastic Additive 9050 with a resulting VOC of less than their original VOC Value. Applied VOC LE Applied VOC LE g/l Color Coating VOC Limit 3.5 lbs/gal (420 g/l) Product Mix Ratio Hardener Reducer lbs/gal Less Water & Less Water & Permahyd Base Coat Series 280/285 N/A **/*** +0-15% 6000 ***For underhood/door jam applications, up to 10% (by volume) of Permahyd Additive 9007 can be added to the Permahyd Base Coat. Activated basecoat layer should be cleared with Permacron Matte Clear Coat 8091 when used for underhood/door jam applications. In situations of high temperature and/or low humidity, up to 10% of Permahy Special Water 6002 slow can replace Permahyd VE Water 6000 as the Permahyd Base Coat Series 280/285 reducer. Clear Coating VOC Limit 2.1 lbs/gal (250 g/l) Product Mix Ratio Hardener Reducer Permacron 2.1 Clear Coat 8095 or :1 3193, 3195, 3197, % and 8097 may be mixed with 15-30% Elastic Additive 9050 with a resulting VOC of less than their original VOC Value. 3369, 3370, 3371 Up to 2% (by volume) of Permacron Antisilicone 8510 can be added to 8095 and 8097 with a resulting compliant VOC Value. Permacron Matte Clear Coat :1 3193, 3195, 3197, % In Mixture of 3 Parts 8091 to 1 Part 8095 or , 3370, 3371 Satin Finish Uniform Finish Coating 4.5 lbs/gal (540 g/l) Product Mix Ratio Hardener Reducer Permacron Speed Blender : * Only with activated Permacron 2.1 Clear Coat 8095 or 8097 mixed as stated here in the manufacturer's instructions. 2 Parts 8095 or 8097 to 1 Part 3193, + 10% 3370, + 50% 1036 Permahyd Blend-in Additive :1 Adhesion Promoter 4.5 lbs/gal (540 g/l) (Effective 1/1/2010) Applied VOC LE lbs/gal Less Water & Applied VOC LE lbs/gal Less Water & +10% % Permahyd Base Coat Series 280/285 (RTS) N/A Applied VOC LE lbs/gal Less Water & Applied VOC LE g/l Less Water & Applied VOC LE g/l Less Water & Applied VOC LE g/l Less Water & Product Mix Ratio Hardener Reducer Priomat Elastic Primer 4190 Ready N/A N/A Priomat Elastic Primer 3304 (Spray Can) N/A N/A N/A EXEMPT Other Products Product Permahyd Sanding Paste 1120 Raderal Spray Polyester 3508 Gray Beige For jurisdiction, applicability, solvent handling, recordkeeping, exemptions, or for detailed information about local regulations, please contact Regulatory at Copyright 2009 DuPont. Spies Hecker, Permacron, Permasolid, Permanent, Priomat and Permahyd are registered trademarks of E.I. du Pont de Nemours and Company for its brands of refinish systems. All rights reserved.

4 Spies Hecker V.O.C. Compliance Chart (Mercedes Benz Approved Products) San Diego County Air Pollution Control District, Rule /97 (SCM Limits Tentative 2010) Edition: November 6, 2009 Surface Preparation VOC Limit Rule Metal: 1.6 lbs/gal (200 g/l)/ Vapor Pressure <20 mmhg) Plastics: 6.5 lbs/gal (780 g/l)/vapor Pressure (<45 mmhg) Applied VOC lbs/gal Applied VOC g/l Permahyd Silicone Remover 7090 N/A N/A N/A Permahyd Silicone Remover 7085 N/A N/A N/A Permanent Silicone Remover 7010 Slow N/A N/A N/A 7.5 mmhg Permahyd Plastic Cleaning Paste 7081 N/A N/A N/A Applied VOC LE Applied VOC Pretreatment VOC Limit 6.5 lbs/gal (780 g/l) lbs/gal Less LE g/l Less Water & Water & Product Mix Ratio Hardener Reducer Priomat 5.5 Wash Primer 4055 Gray N/A Priomat Wash Primer 4075 Gray 1: N/A Priomat 1K Primer Surfacer 4085 N/A N/A +50% , 3363, 3365, 3366 Priomat 1K Primer Surfacer 4085 (Spray Can) N/A N/A N/A EXEMPT Applied VOC LE Applied VOC Primer/Primer Surfacer VOC Limit 3.5 lbs/gal (420 g/l) lbs/gal Less LE g/l Less Water & Water & Product Mix Ratio Hardener Reducer Permahyd Primer Surfacer 4100 N/A N/A +0-10% Permacron 2.1 VHS Surfacer : % , 3363, 3365, 3366 Permasolid 2.1 Surfacer :1 3193, 3195, 3197, % , 3370, 3371 Permasolid 2.1 Surfacer 5155 with 30% Elastic Additive :1 3193, 3195, 3197, % , 3370, 3371 Applied VOC LE Applied VOC Primer Sealer VOC Limit 3.5 lbs/gal (420 g/l) lbs/gal Less LE g/l Less Water & Water & Product Mix Ratio Hardener Reducer Permahyd Stonechip Protector 7100 N/A N/A +0-10% Permasolid VHS Wet on Wet Surfacer :1 3193, 3195, 3197, % , 3370, 3371 Permasolid 2.1 Surfacer :1 3193, 3195, 3197, % % 3369, 3370, 3371 Permasolid Spectro Surfacer :1 3193, 3195, 3197, % and 5400 may be mixed with Elastic Additive 9050 with a resulting VOC of less than their original VOC Value. Multi Stage Topcoat VOC Limit 4.5 lbs/gal (540 g/l) Product Mix Ratio Hardener Reducer Waterborne BC Option Permahyd Base Coat Series 280/285 N/A **/*** +0-15% 6000 Applied VOC LE Applied VOC lbs/gal Less LE g/l Less Water & Water & **Up to 5% (by vol.) of Permahyd Additive 9007 can be added to two-stage basecoats and the ground coat of three-stage formulas. ***For underhood/door jam applications, up to 10% (by volume) of Permahyd Additive 9007 can be added to the Permahyd Base Coat. In situations of high temperature and/or low humidity, up to 10% of Permahyd Special Water 6002 slow can replace Permahyd VE Water 6000 as the Permahyd Base Coat Series 280/285 reducer. Followed by: 2*CC+1*BC/3 2*CC+2*BC/4 Permasolid HS Diamond Clear Coat : N/A & 3 Stage Permasolid HS Clear Coat :1 3193, 3195, 3197, % & 3 Stage 8580, 3363, 3365, 3366 Permasolid HS Clear Coat :1 3193, 3195, 3197, % & 3 Stage 9030 Permasolid HS Clear Coat :1 3193, 3195, 3197, % & 3 Stage 3369, 3370, 3371 Permacron 2.1 Clear Coat 8095 or :1 3193, 3195, 3197, % & 3 Stage 3369, 3370, 3371 Permacron MS Clear Coat :1 3193, 3195, 3197, % & 3 Stage 3369, 3370, 3371 Permacron Matte Clear Coat :1 3193, 3195, 3197, % Flat Finish 3369, 3370, & 3 Stage Permacron Matte Clear Coat :1 3193, 3195, 3197, % In Mixture of 3 Parts 8091 to 1 Part 8095 or , 3370, 3371 Satin Finish 2 & 3 Stage The above Top Coats (excluding 8091) may be mixed with 15-30% Elastic Additive 9050 with a resulting VOC of less than their original VOC Value should only be used with 8450 when painting soft PUR parts. Solventborne BC Option 2*CC+1*BC/3 Permacron Base Coat Series 293/295 N/A N/A % 3054, 3055, 3056 OR GM 4901M Recommendations Permacron Base Coat Series 293/ % 3193, 3195, 3197, % 3054, 3055, 3056 Followed by: Permacron 2.1 Clear Coat 8095 or :1 3193, 3195, 3197, % 2*CC+1*BC/ & 3 Stage 3369, 3370, 3371 Permacron 2.1 Clear Coat 8095 or :1 3193, 3195, 3197, % Stage 9030 Permacron Matte Clear Coat :1 3193, 3195, 3197, % Flat Finish 3369, 3370, & 3 Stage Permacron Matte Clear Coat :1 3193, 3195, 3197, % In Mixture of 3 Parts 8091 to 1 Part 8095 or , 3370, 3371 Satin Finish 2 & 3 Stage Permasolid HS Diamond Clear Coat :1 3193, 3195, 3197, 3199 N/A Stage Permasolid HS Clear Coat :1 3193, 3195, 3197, % Stage 3369, 3370, 3371 Permasolid HS Clear Coat :1 3193, 3195, 3197, % Stage 8580, 3363, 3365, 3366 Permacron MS Clear Coat :1 3193, 3195, 3197, % Stage 3369, 3370, 3371 The above Top Coats (excluding 8091) may be mixed with 15-30% Elastic Additive 9050 with a resulting VOC of less than their original VOC Value should only be used with 8450 when painting soft PUR parts. Applied VOC LE Applied VOC lbs/gal Less LE g/l Less Specialty Coatings VOC Limit 7.0 lbs/gal (840 g/l) Water & Water & Product Mix Ratio Hardener Reducer Elastomeric Coatings Permacron 1:1 Elastic Primer Surfacer 3300 Gray 1: N/A Permacron 1:1 Elastic Primer Surfacer 3300 Black 1: N/A Priomat Elastic Primer 3304 Ready N/A N/A Priomat Elastic Primer 4190 Ready N/A N/A Permacron Semi-gloss Elastic Clear Coat :1 3193, 3195, 3197, % , 3363, 3365, 3366 Uniform Finish Blenders Permacron Speed Blender :1 Permacron & Permasolid Clear Coats (RTS) N/A Permahyd Blend-in Additive :1 Permahyd Base Coat Series 280/285 (RTS) N/A Fisheye Eliminators Permacron Antisilicone ml:1 2K Acrylic Topcoats (RTS) N/A Ralley Matt Black FP1004 3:1 3193, 3195, 3197, % , 3363, 3365, 3366 Permacron Clear Brilliant Effect 8560 Ready N/A N/A Other Products Product Permahyd Sanding Paste 1120 Raderal Spray Polyester 3508 Gray Beige For jurisdiction, applicability, solvent handling, recordkeeping, exemptions, or for detailed information about local regulations, please contact Regulatory at Copyright 2009 DuPont. Spies Hecker, Permacron, Permasolid, Permanent, Priomat and Permahyd are registered trademarks of E.I. du Pont de Nemours and Company for its brands of refinish systems. All rights reserved.

5 Mojave Desert Air Quality Management District - Rule 1116, 7/00 (Mercedes Benz Approved Products) Edition: November 06, 2009 Surface Preparation lbs/gal (25 g/l) As Supplied/Packaged VOC lbs/gal As Supplied/Packaged VOC g/l Product Mix Ratio Hardener Reducer Permahyd Silicone Remover 7085 Aerosol (Exempt) N/A N/A N/A EXEMPT Permahyd Silicone Remover 7096 N/A N/A N/A Permahyd Plastic Cleaning Paste 7081 N/A N/A N/A Pretreatment VOC Limit 6.5 lbs/gal (780 g/l) Product Mix Ratio Hardener Reducer Priomat 5.5 Wash Primer 4055 Gray N/A Priomat 1K Primer Surfacer 4085 N/A N/A +50% , 3363, 3365, 3366 Priomat Wash Primer 4075 Gray 1: N/A Priomat 1K Primer Surfacer 4085 (Spray Can) N/A N/A N/A EXEMPT Primer/Primer Surfacer VOC Limit 2.1 lbs/gal (250 g/l) Applied VOC LE lbs/gal Less Water & Applied VOC LE g/l Less Water & Product Mix Ratio Hardener Reducer Permahyd Primer Surfacer 4100 N/A N/A 0-10% Permacron 2.1 VHS Surfacer : % , 3363, 3365, 3366 Permasolid 2.1 Surfacer :1 3193, 3195, 3197, % , 3370, 3371 Permasolid 2.1 Surfacer 5155 with 30% Elastic Additive :1 3193, 3195, 3197, % , 3370, 3371 Primer Sealer VOC Limit 2.8 lbs/gal (340 g/l) (Until 1/1/2010) Product Mix Ratio Hardener Reducer Permahyd Stonechip Protector 7100 N/A % Permasolid 2.1 Surfacer :1 3193, 3195, 3197, % % 3369, 3370, 3371 Permasolid VHS Wet on Wet Surfacer :1 3193, 3195, 3197, % , 3370, may be mixed with 15-30% Elastic Additive 9050 with a resulting VOC of less than their original VOC Value. Multi Stage Topcoat VOC Limit 3.5 lbs/gal (420 g/l) Applied VOC LE lbs/gal g/l Product Mix Ratio Hardener Reducer Less Water & Waterborne BC Option Multistage System VOC Limit 3.5 lbs/gal Permahyd Base Coat Series 280/285 N/A **/*** +0-15% 6000 **Up to 5% (by vol.) of Permahyd Additive 9007 can be added to two-stage basecoats and the ground coat of three-stage formulas. Applied VOC LE lbs/gal Less Water & Applied VOC LE lbs/gal Less Water & Applied VOC LE g/l Less Water & Applied VOC LE g/l Less Water & ***For underhood/door jam applications, up to 10% (by volume) of Permahyd Additive 9007 can be added to the Permahyd Base Coat. Activated basecoat layer should be cleared with Permacron Matte Clear Coat 8091 when used for underhood/door jam applications. In situations of high temperature and/or low humidity, up to 10% of Permahyd Special Water 6002 slow can replace Permahyd VE Water 6000 as the Permahyd Base Coat Series 280/285 reducer. Followed by: 2*CC+1*BC/3 2*CC+2*BC/4 Permasolid HS Clear Coat :1 3193, 3195, 3197, % , 3363, 3365, 3366 Permasolid HS Diamond Clear Coat :1 3193, 3195, 3197, 3199 N/A Permacron 2.1 Clear Coat 8095 or :1 3193, 3195, 3197, % , 3370, 3371 Permacron Matte Clear Coat :1 3193, 3195, 3197, % Flat Finish 3369, 3370, 3371 Permacron Matte Clear Coat :1 3193, 3195, 3197, % In Mixture of 3 Parts 8091 to 1 Part 8095 or , 3370, Satin Finish The above Top Coats (excluding 8091) may be mixed with 15-30% Elastic Additive 9050 with a resulting VOC of less than their original VOC Value should only be used with 8450 when painting soft PUR parts. Solventborne BC Option 2*CC+1*BC/3 Permacron Base Coat Series 293/295 N/A N/A % 3054, 3055, 3056 OR GM 4901M Recommendations Permacron Base Coat Series 293/ % 3193, 3195, 3197, % 3054, 3055, 3056 Followed by: 2*CC+1*BC/3 Permacron 2.1 Clear Coat 8095 or :1 3193, 3195, 3197, % , 3370, 3371 The above Top Coats may be mixed with 15-30% Elastic Additive 9050 with a resulting VOC of less than their original VOC Value. Specialty Coatings VOC Limit 7.0 lbs/gal (840 g/l) Applied VOC LE lbs/gal Applied VOC LE g/l Product Mix Ratio Hardener Reducer Less Water & Elastomeric Coatings Permacron 1:1 Elastic Primer Surfacer 3300 Gray 1: N/A Permacron 1:1 Elastic Primer Surfacer 3300 Black 1: N/A Priomat Elastic Primer 3304 Ready N/A N/A Priomat Elastic Primer 4190 Ready N/A N/A Permacron Semi-gloss Elastic Clear Coat :1 3193, 3195, 3197, % , 3363, 3365, 3366 Uniform Finish Blenders Permacron Speed Blender :1 Permacron Clear Coats (RTS) N/A Permahyd Blend-in Additive 9005 Permahyd Base Coat Series 280/285 1:1 (RTS) N/A Fisheye Eliminators Permacron Antisilicone ml:1 2K Acrylic Topcoats (RTS) N/A Ralley Matt Black FP1004 3:1 3193, 3195, 3197, % , 3363, 3365, 3366 Permacron Clear Brilliant Effect 8560 Ready N/A N/A Other Products Product Permahyd Sanding Paste 1120 Raderal Spray Polyester 3508 Gray Beige For jurisdiction, applicability, solvent handling, recordkeeping, exemptions, or for detailed information about local regulations, please contact Regulatory at Copyright 2009 DuPont. Spies Hecker, Permacron, Permasolid, Permanent, Priomat and Permahyd are registered trademarks of E.I. du Pont de Nemours and Company for its brands of refinish systems. All rights reserved.

6 Spies Hecker V.O.C. Compliance Chart (Mercedes Benz Approved Products) South Coast Air Quality Management District - Rule 1151/1171, Effective January 1, 2010 Edition 03/08/2010 Surface Preparation lbs/gal (25 g/l) As Supplied/Packaged VOC lbs/gal As Supplied/Packaged VOC g/l Product Mix Ratio Hardener Reducer Permahyd Silicone Remover 7085 Aerosol (Exempt) N/A N/A N/A EXEMPT Permahyd Silicone Remover 7096 N/A N/A N/A Permahyd Plastic Cleaning Paste 7081 N/A N/A N/A Pretreatment VOC Limit 5.5 lbs/gal (660 g/l) **Up to 5% (by vol.) of Permahyd Additive 9007 can be added to two-stage basecoats and the ground coat of three-stage formulas. Applied VOC LE lbs/gal Less Water & Applied VOC LE g/l Less Water & Product Mix Ratio Hardener Reducer Priomat 5.5 Wash Primer 4055 Gray N/A Priomat 1K Primer Surfacer 4085 (Spray Can) N/A N/A N/A EXEMPT Primer VOC Limit 2.1 lbs/gal (250 g/l) Applied VOC LE lbs/gal Less Water & Applied VOC LE g/l Less Water & Product Mix Ratio Hardener Reducer Permahyd Primer Surfacer 4100 N/A N/A 0-10% Permacron 2.1 VHS Surfacer : % , 3363, 3365, 3366 Permasolid 2.1 Surfacer :1 3193, 3195, 3197, % , 3370, 3371 Permasolid 2.1 Surfacer 5155 with 30% Elastic Additive :1 3193, 3195, 3197, % , 3370, 3371 Primer VOC Limit 2.1 lbs/gal (250 g/l) (Effective 1/1/2010) Applied VOC LE lbs/gal Less Water & Applied VOC LE g/l Less Water & Product Mix Ratio Hardener Reducer Permahyd Stonechip Protector 7100 N/A N/A +0-10% Permasolid Non-Sanding Sealer 5156 Gray 2:1 3193, 3195, 3197, % % 3369, 3370, may be mixed with 15-30% Elastic Additive 9050 with a resulting VOC of less than their original VOC Value. Applied VOC LE Applied VOC LE g/l Color Coating VOC Limit 3.5 lbs/gal (420 g/l) Product Mix Ratio Hardener Reducer lbs/gal Less Water & Less Water & Permahyd Base Coat Series 280/285 N/A **/*** +0-15% 6000 ***For underhood/door jam applications, up to 10% (by volume) of Permahyd Additive 9007 can be added to the Permahyd Base Coat. Activated basecoat layer should be cleared with Permacron Matte Clear Coat 8091 when used for underhood/door jam applications. In situations of high temperature and/or low humidity, up to 10% of Permahyd Special Water 6002 slow can replace Permahyd VE Water 6000 as the Permahyd Base Coat Series 280/285 reducer. Clear Coating VOC Limit 2.1 lbs/gal (250 g/l) Product Mix Ratio Hardener Reducer Permacron 2.1 Clear Coat 8095 or :1 3193, 3195, 3197, % and 8097 may be mixed with 15-30% Elastic Additive 9050 with a resulting VOC of less than their original VOC Value. 3369, 3370, 3371 Up to 2% (by volume) of Permacron Antisilicone 8510 can be added to 8095 and 8097 with a resulting compliant VOC Value. Permacron Matte Clear Coat :1 3193, 3195, 3197, % In Mixture of 3 Parts 8091 to 1 Part 8095 or , 3370, 3371 Satin Finish Uniform Finish Coating 4.5 lbs/gal (540 g/l) Product Mix Ratio Hardener Reducer Permacron Speed Blender : * Only with activated Permacron 2.1 Clear Coat 8095 or 8097 mixed as stated here in the manufacturer's instructions. 2 Parts 8095 or 8097 to 1 Part 3193, + 10% 3370, + 50% 1036 Applied VOC LE lbs/gal Less Water & Applied VOC LE lbs/gal Less Water & Applied VOC LE g/l Less Water & Applied VOC LE g/l Less Water & +10% % Permahyd Blend-in Additive 9005 Permahyd Base Coat Series 280/285 1:1 (RTS) N/A Adhesion Promoter 4.5 lbs/gal (540 g/l) (Effective 1/1/2010) Applied VOC LE lbs/gal Less Water & Applied VOC LE g/l Less Water & Product Mix Ratio Hardener Reducer Priomat Elastic Primer 4190 Ready N/A N/A Priomat Elastic Primer 3304 (Spray Can) N/A N/A N/A EXEMPT Other Products Product Permahyd Sanding Paste 1120 Raderal Spray Polyester 3508 Gray Beige For jurisdiction, applicability, solvent handling, recordkeeping, exemptions, or for detailed information about local regulations, please contact Regulatory at Copyright 2009 DuPont. Spies Hecker, Permacron, Permasolid, Permanent, Priomat and Permahyd are registered trademarks of E.I. du Pont de Nemours and Company for its brands of refinish systems. All rights reserved.

7 Technical Data Sheet. Permahyd Silicone Remover 7085,and 7096 Permahyd Silicone Removers 7085 and 7095 are waterborne cleaning agents with very low organic solvent content and special cleaning additives. This product is for professional painting of vehicles only. VR Technical Data Sheet No (10/94) Jan Copyright 2009Dupont. Spies Hecker, Raderal, Permacron, Permahyd, Permasolid, Priomat, and Permanent are registered trademarks of E.I. du Pont de Nemours and Company for its brands of refinish systems. All rights reserved.

8 Permahyd Silicone Remover 7085/7090/7095 Field of Application Application Special note: For cleaning surfaces prior to applying primers, surfacers, or top coats. Apply Permahyd Silicone Removers 7085, or 7096 with a spray bottle or clean cloth. Wipe dry with a clean cloth before Permahyd Silicone Remover 7085, or 7096 evaporates. 1. Allow cleaned surfaces to dry completely before recoating. 2. Do not allow Silicone Remover to dry on the surface. 3. These products are not suitable for cleaning spray guns or tools. 4. Always use a clean cloth. 5. These products are not suitable for removing release agent from UP-GF or other plastic parts. 6. Heavily soiled areas must be cleaned twice. Important Regulatory Information Please see the appropriate VOC Wallchart for compliance for your area. The values depicted below are as supplied. VOC Category VOC As Supplied Density g/l Wt% Volatiles, Water & Surface Preparation 7096 Surface Preparation Liter Surface Preparation Spray Vol% Water & 1.6 lbs/gal g/l 947 g/l 99.9% 75.9% TBD For industrial use only by professional, trained painters. Not for sale to or use by the general public. Before using, read and follow all label and MSDS precautions. If mixed with other components, mixture will have hazards of all components. Do not sand, flame cut, braze or weld dry coating without a NIOSH approved air purifying respirator with particulate filters or appropriate ventilation, and gloves. Any analytical results set forth herein do not constitute a warranty of specific product features or of the product s suitability for a specific purpose. All products are sold pursuant to our general conditions of sale. We hereby disclaim all warranties and representations, express or implied, with respect to this product, including any warranty of merchantability or fitness for a particular purpose. This product is protected by patent law, trademark law, copyright law, international treaties and/or other applicable law. All rights reserved. Unauthorized sale, manufacturing or use may result in civil and criminal penalties. SPIES HECKER, INC West Anchor Court Plymouth, MI Tel SPIES Fax Copyright 2009Dupont. Spies Hecker, Raderal, Permacron, Permahyd, Permasolid, Priomat, and Permanent are registered trademarks of E.I. du Pont de Nemours and Company for its brands of refinish systems. All rights reserved.

9 Technical Data Sheet. Permanent Silicone Remover 7010 Slow Permanent Silicone Remover 7010 is a slowly evaporating organic solvent mixture used primarily to remove oil and grease residues. This product is used for cleaning sanded, old or original finishes, and surfaces coated with primer or surfacer which have been subsequently sanded is also available in an aerosol spray. This product is for professional painting of vehicles only. VR Technical Data Sheet No. 070(10/94) Jun Copyright 2009 Dupont. Spies Hecker, Raderal, Permacron, Permahyd, Permasolid, Priomat, and Permanent are registered

10 Permanent Silicone Remover 7010 Slow and 7799 Fast Field of Application Application For cleaning surfaces prior to applying primers, surfacers, or top coats. Apply with Permanent Silicone Remover 7010 Slow with a spray bottle or clean cloth. Wipe dry with a clean cloth before Permanent Silicone Remover 7010 Slow evaporates. Special note: 1. Allow cleaned surfaces to dry completely before recoating. 2. Do not allow Permanent Silicone Remover 7010 Slow to dry on the surface. 3. This product is not suitable for cleaning spray guns or tools. 4. Always use a clean cloth. 5. Heavily soiled areas must be cleaned twice. 6. Permahyd Silicone Removers 7085, or 7096 must be used for final cleaning prior to use of any Permahyd product. Important Regulatory Information Please see the appropriate VOC Wallchart for compliance for your area. The values depicted below are as supplied. VOC Category VOC As Supplied Density g/l Wt% Volatiles, Water & Vol% Water & Surface Preparation 6.3 lbs/gal g/l 757 g/l 100% 0% Slow (5 Liter) Surface Preparation Slow (Spray) 100% g/l 750 g/l 100% 0% For industrial use only by professional, trained painters. Not for sale to or use by the general public. Before using, read and follow all label and MSDS precautions. If mixed with other components, mixture will have hazards of all components. Do not sand, flame cut, braze or weld dry coating without a NIOSH approved air purifying respirator with particulate filters or appropriate ventilation, and gloves. Any analytical results set forth herein do not constitute a warranty of specific product features or of the product s suitability for a specific purpose. All products are sold pursuant to our general conditions of sale. We hereby disclaim all warranties and representations, express or implied, with respect to this product, including any warranty of merchantability or fitness for a particular purpose. This product is protected by patent law, trademark law, copyright law, international treaties and/or other applicable law. All rights reserved. Unauthorized sale, manufacturing or use may result in civil and criminal penalties. SPIES HECKER West Anchor Court Plymouth, MI Tel SPIES Fax Copyright 2009 Dupont. Spies Hecker, Raderal, Permacron, Permahyd, Permasolid, Priomat, and Permanent are registered

11 4100 Technical Data Sheet Permahyd 1K Primer Surfacer 4100 Permahyd 1K Primer Surfacer 4100 is primarily used for spot repairs and for isolating areas of old finishes which have been sanded through. Permahyd 1K Primer Surfacer 4100 is available in gray. This product is for professional painting of vehicles only. Technical Data Sheet No Apr. 2011

12 4100 Suitable Substrates: Bare Steel Galvanized Steel Aluminum Sanded E-Coat Original or old paintwork Raderal Polyester products. Substrate pretreatment: Degrease and sand. Before further treatment, clean all substrates thoroughly with Permaloid Silicone Removers 7087 or 7010 Slow, Permahyd Silicone Remover 7085, or Permahyd Silicone Remover Mixing ratio: Hand stir Approximately 5-10% Permahyd VE Water Pot Life: Unlimited Reducer: Permahyd VE Water 6000 Method of application HVLP Approved Transfer Efficiency Please refer to gun manufacturer and local legislation for proper spray pressure recommendations. Spray Nozzle mm mm Application viscosity 4mm, 68 F/20 C, DIN seconds Reducer at 68 F/20 C material temperature 5-10% (measure carefully) Number of coats 2-3 (with intermediate flash-off*) Recommended film thickness: approx. 2 3 mil dry film thickness

13 4100 Flash-off time: (air drying) Low baking: At 68 F/ 20 C a) Flash: minutes b) Sandable 1 3 hours Infra-red drying: flash-off time: approx. 5 minutes at 68 F/ 20 C drying time and temperature: approx. 30 minutes at 140 F/60 C metal temperature. flash-off time: approx. 5 minutes at 68 F/ 20 C short wave: 5 minutes at 50% power and then10 minutes at 100% power medium wave: 20 minutes *The flash-off time depends on the temperature, humidity and air flow in the spray booth. Dry sanding: Wet sanding: With random orbital sander and dust extraction. (final - P ). P Note: After wet sanding, allow primer surfacer to dry for 30 minutes at 68 F/ 20 C before recoating. Recoat With: Permacron Base Coat Series 293/295 Permahyd Hi-TEC 480 Permahyd Base Coat Series 280/285/286 Special Tips: 1. Spraying equipment must be suitable for the application of waterborne products; manufacturer s instructions must be followed. For further information, please refer to VR Technical Data Sheet No Rinse spray equipment with Permahyd VE Water 6000 before and after use. For further information, please refer to VR Technical Data Sheet No Liquid waste from waterborne products must be collected separately from conventional liquid paint waste. If mixed, disposal may be impossible, and in any case more difficult and consequently more expensive. For further information, please refer to VR Technical Data Sheet No

14 4100 Important Regulatory Information VOC Category VOC Regulatory Density g/l Wt% Volatiles, Water & Vol% Water & and Actual Primer 173 g/l, 83 g/l 1398 g/l 42.6%, 36.3%, 0.0% 49.5% For industrial use only by professional, trained painters. Not for sale to or use by the general public. Before using, read and follow all label and MSDS precautions. If mixed with other components, mixture will have hazards of all components. Ready to use paint materials containing isocyanates can cause irritation of the respiratory organs and hypersensitive reactions. Asthma sufferers, those with allergies and anyone with a history of respiratory complaints must not be asked to work with products containing isocyanates. Do not sand, flame cut, braze or weld dry coating without a NIOSH approved air purifying respirator with particulate filters or appropriate ventilation, and gloves. Any analytical results set forth herein do not constitute a warranty of specific product features or of the product s suitability for a specific purpose. All products are sold pursuant to our general conditions of sale. We hereby disclaim all warranties and representations, express or implied, with respect to this product, including any warranty of merchantability or fitness for a particular purpose. This product is protected by patent law, trademark law, copyright law, international treaties and/or other applicable law. All rights reserved. Unauthorized sale, manufacturing or use may result in civil and criminal penalties. SPIES HECKER, INC West Anchor Court Plymouth, MI Tel ( SPIES) Fax

15 5150 Technical Data Sheet Permasolid 2.1 VHS Surfacer 5150 Permasolid 2.1 VHS Surfacer 5150 is a 2K acrylic product based on a special reactive binder with high solids content. This surfacer has excellent vertical stability, very high build, and good sanding properties because of it s lower solvent content and less tendency to produce edge mapping. This product is for professional painting of vehicles only. Technical Data Sheet No Apr. 2011

16 5150 Suitable Substrates: Fiberglass (UP-GF) Thoroughly degreased, unsanded or lightly sanded E-coat. Original or old paintwork (except reversible substrates, Example: lacquer) Raderal Polyester products Priomat Primers Substrate pretreatment: Degrease and sand. Before further treatment, clean all substrates thoroughly with Permaloid Silicone Removers 7087 or 7010 Slow, Permahyd Silicone Remover 7085, or Permahyd Silicone Remover Mixing ratio: 2:1 by volume with Permasolid VHS Hardener Pot Life: Ready for spraying approx minutes application time at 68 F/20 C Reducer: Regulated Market 20-30% Permacron Reducer 3369 Fast, Permacron Reducer 3370 Medium, or Permacron Reducer 3371 Slow. For optimum reducer selection, refer to TDS # Method of application HVLP Approved Transfer Efficiency Please refer to gun manufacturer and local legislation for proper spray pressure recommendations. Spray Nozzle mm mm Application viscosity 4mm, 68 F/20 C, DIN 4 Approx. 25 seconds Reducer at 68 F/20 C material temperature Regulated Market 20 to 30% Number of coats 1-3 (with intermediate flash-off time of approx. 10 minutes) Recommended film thickness: mil dry film thickness (maximum 8 mil)

17 5150 Air drying: (Dry for sanding). At 68 F/ 20 C Up to 4.8 mil after 4 hours At 68 F/ 20 C Above 4.8 mil overnight Low bake: Flash-off time: 5-15 minutes Drying time and temperature: 60 minutes at 140 F/60 C metal temperature Not recommended for film thicknesses more than 4 mil Infra-red drying: Flash-off time: Short wave: Medium wave: 5-15 minutes 5 minutes half power, then 15 minutes full power. 30 minutes. Note: After low bake or infra-red drying, allow the surfacer to cool down for 30 minutes before sanding. With less than 50% air humidity, allow for longer drying time. Dry sanding: With random orbital sander and dust extraction Initial sanding: P320 Final sanding: P Wet sanding: Initial sanding: P320 Final sanding: P Recoat With: Permahyd Hi-TEC 480 or Base Coat Series 280/285/286 Special tips: 1. In order to make sanding easier, apply Guide Coat before sanding. Do not spray onto wet surfacer. 2. With air drying a minimum temperature of 59 F/15 C must be maintained.

18 5150 Important Regulatory Information Please see the appropriate VOC wall chart for compliance for your area. The values depicted below are ready to spray. VOC Category VOC Regulatory Density g/l Wt% Volatiles, Water & Vol% Water & and Actual Primer (250 g/l) 193 g/l, 153 g/l 1531 g/l 27.2%, 0.0% & 17.1% 20.4% Primer (National Rule) 258 g/l, 258 g/l 1553 g/l 16.0%, 0.0%, & 0.0% 0.0% For industrial use only by professional, trained painters. Not for sale to or use by the general public. Before using, read and follow all label and MSDS precautions. If mixed with other components, mixture will have hazards of all components. Ready to use paint materials containing isocyanates can cause irritation of the respiratory organs and hypersensitive reactions. Asthma sufferers, those with allergies and anyone with a history of respiratory complaints must not be asked to work with products containing isocyanates. Do not sand, flame cut, braze or weld dry coating without a NIOSH approved air purifying respirator with particulate filters or appropriate ventilation, and gloves. Any analytical results set forth herein do not constitute a warranty of specific product features or of the product s suitability for a specific purpose. All products are sold pursuant to our general conditions of sale. We hereby disclaim all warranties and representations, express or implied, with respect to this product, including any warranty of merchantability or fitness for a particular purpose. This product is protected by patent law, trademark law, copyright law, international treaties and/or other applicable law. All rights reserved. Unauthorized sale, manufacturing or use may result in civil and criminal penalties. SPIES HECKER, INC West Anchor Court Plymouth, MI Tel ( SPIES) Fax

19 5155 Technical Data Sheet Permasolid 2.1 Surfacer 5155 Permacron 2.1 Surfacer 5155 is a high quality 2K acrylic urethane. Permacron 2.1 Surfacer 5155 has excellent vertical stability, very high build, and good sanding properties while having a VOC of 2.1 lbs/gal. The fast drying and excellent leveling of this surfacer will provide high production. This product is for professional painting of vehicles only. Technical Data Sheet No Apr. 2011

20 5155 Suitable Substrates: Fiberglass (UP-GF) Thoroughly degreased, unsanded or lightly sanded E-coat. Original or old paintwork (except reversible substrates, Example: lacquer) Raderal Polyester products Priomat Primers Substrate pretreatment: Mixing ratio: Degrease and sand. Before further treatment, clean all substrates thoroughly with Permaloid Silicone Removers 7087 or 7010 Slow, Permahyd Silicone Remover 7085, or Permahyd Silicone Remover For use as a Sanding Surfacer 4:1 by volume with Permacron Hardeners 3193 Fast, 3195 Medium, 3197 Slow or 3199 Extra Slow. Pot Life: Ready for spraying approx minutes application time at 68 F/20 C. Reducer: 20-30% Permacron Reducer 3369 Fast, Permacron Reducer 3370 Medium, or Permacron Reducer 3371 Slow. Method of application HVLP Approved Transfer Efficiency Please refer to gun manufacturer and local legislation for proper spray pressure recommendations. Spray Nozzle mm mm Application viscosity 4mm, 68 F/20 C, DIN seconds Reducer at 68 F/20 C material temperature 20% - 30% Number of coats 2-4 Recommended film thickness: mil dry film thickness

21 5155 Air drying: (Dry for sanding) At 68 F/ 20 C mil after 3-4 hours At 68 F/ 20 C Above 6 mil after 12 hours Low bake: Flash-off time: 5-15 minutes Drying time and temperature: mil 30 minutes at 140 F/60 C metal temperature 6-8 mil 40 minutes at 140 F/60 C metal temperature Infra-red drying: Flash-off time: 5-15 minutes Short wave: mil 10 minutes Short wave: 6-8 mil 15 minutes Medium wave: mil 15 minutes Medium wave: 6 8 mil 20 minutes Dry sanding: With random orbital sander and dust extraction Initial sanding: P320 Final sanding: P Wet sanding: Initial sanding: P320 Final sanding: P Recoat With: Permahyd Hi-TEC 480 or Base Coat Series 280/285/286 Special tips: 1. In order to make sanding easier, apply Guide Coat before sanding. Do not spray onto wet surfacer. 2. With air drying a minimum temperature of 59 F/15 C must be maintained. 3. For best isolation properties, a dry film thickness of 3-4 mil applied in 2 coats and air dried over night is recommended. On critical substrates, 5155 should be applied to the entire panel.

22 5155 For use as a Wet-On-Wet Sealer Mixing ratio: 2:1 Permacron Hardeners 3193 Fast, 3195 Medium, 3197 Slow or 3199 Extra Slow. Pot Life: Ready for spraying approx. 60 minutes application time at 68 F/20 C. (depending on the hardener used) Additive: Permasolid 2.1 Wet-on-Wet-Additive 9070 Method of application HVLP Approved Transfer Efficiency Please refer to gun manufacturer and local legislation for proper spray pressure recommendations. Spray Nozzle mm mm Application viscosity 4mm, 68 F/20 C, DIN 4 16 seconds Reducer at 68 F/20 C material temperature 30% Number of coats a) 1.5 coat operation = 1 medium coat followed by 1 full coat without Intermediate flash-off time. b) 2 coats with approx. 5 minutes intermediate flash-off Flash-off time (before top coat) After flash-off at 68 /20 C recoat with: 15 minutes to max. 30 minutes Permacron Base Coat Series 293/ minutes to max. 120 minutes Permahyd Hi-TEC or Base Coat Series 280/285/286 Recommended film thickness: Approx. 1.2 mil dry film thickness

23 5155 Important Regulatory Information Please see the appropriate VOC wall chart for compliance for your area. The values depicted below are ready to spray. VOC Category VOC Regulatory Density g/l Wt% Volatiles, Water & Vol% Water & and Actual Primer 250 g/l, 250 g/l 1574 g/l 46.1%, 0.0%, & 36.9% 44.3% Elastomeric Primer 248 g/l, 248 g/l 1430 g/l 49.2%, 0.0%, & 39.1% 42.6% Sealer 240g/l, 240g/l 1458 g/l 52.2%, 0.0%, & 42.3% 46.3% For industrial use only by professional, trained painters. Not for sale to or use by the general public. Before using, read and follow all label and MSDS precautions. If mixed with other components, mixture will have hazards of all components. Ready to use paint materials containing isocyanates can cause irritation of the respiratory organs and hypersensitive reactions. Asthma sufferers, those with allergies and anyone with a history of respiratory complaints must not be asked to work with products containing isocyanates. Do not sand, flame cut, braze or weld dry coating without a NIOSH approved air purifying respirator with particulate filters or appropriate ventilation, and gloves. Any analytical results set forth herein do not constitute a warranty of specific product features or of the product s suitability for a specific purpose. All products are sold pursuant to our general conditions of sale. We hereby disclaim all warranties and representations, express or implied, with respect to this product, including any warranty of merchantability or fitness for a particular purpose. This product is protected by patent law, trademark law, copyright law, international treaties and/or other applicable law. All rights reserved. Unauthorized sale, manufacturing or use may result in civil and criminal penalties. SPIES HECKER, INC West Anchor Court Plymouth, MI Tel ( SPIES) Fax