Liner Take-Up Option/Maintenance Kit

Size: px

Start display at page:

Download "Liner Take-Up Option/Maintenance Kit"

Nickolas Mosley
5 years ago
Views:

1 Liner Take-Up Option/Maintenance Kit Installation Instructions This kit includes the parts and documentation necessary to install the Liner Take-up option/maintenance kit into the following printers: ZM400 Read these instructions thoroughly before attempting to install this kit. Prepare for Installation Parts List Table Kit Parts List Item Qty Part Number Description Ref 79868M ZM400 Liner Take-Up Maintenance/Option Kit ZM400 Liner Take-up Assembly 7987M ZM400 Liner Take-up Cable HW7887 Screw, M (available in quantities of 5) 4 HW06 E-ring, 0.75 (available in quantities of 5) Bold = Part available for purchase. Italic = Part not available for purchase, listed and shown for reference only. Figure Kit Contents 4 Printed on 007 ZIH Corp. All product names and numbers are Zebra chlorine-free trademarks, and Zebra and the Zebra logo are registered recycled paper. trademarks of ZIH Corp. All rights reserved L-00

2 Liner Take-Up Option/Maintenance Kit Remove the Electronics Cover Reference Materials ZM400/ZM600 User Guide ZM400/ZM600 Maintenance Manual CD Z Series Maintenance Manual CD Tools Required Tools You need these tools to complete this procedure: Phillips Screwdriver Set Antistatic Wriststrap and Mat Metric Nutdriver Set Needle Nose Pliers Safety Goggles Wire Cutters Remove the Electronics Cover Note Retain all parts removed during disassembly, unless otherwise directed.. Caution Turn off (O) the printer and disconnect it from the power source before performing the following procedure. Open the media cover and remove the media and ribbon L-00 A ZM400/ZM600 Installation Instruction 5/0/07

3 Liner Take-Up Option/Maintenance Kit Remove the Electronics Cover. See Figure. Remove the screw and washer securing the electronics cover. Figure Locate the Electronics Cover Mounting Screw 4 Media door Electronics cover Washer 4 Mounting screw. Close the media door. 5/0/07 ZM400/ZM600 Installation Instruction 79868L-00 A

4 4 Liner Take-Up Option/Maintenance Kit Remove the Electronics Cover 4. See Figure. Remove the four mounting screws on the rear of the printer. Figure Remove the Electronics Cover Mounting Screws Electronics cover Mounting screws (4) 5. See Figure 4. Remove the electronics cover by pressing in on the electronics cover with the palm of your hand, and then lifting up on the cover. Figure 4 Remove the Electronics Cover 79868L-00 A ZM400/ZM600 Installation Instruction 5/0/07

5 Liner Take-Up Option/Maintenance Kit Remove the Old Liner Take-up Assembly 5 6. Are you installing the liner take-up assembly as a repair? If Then No Go to Install the New Liner Take-up Assembly on page 8. Yes Continue with Remove the Old Liner Take-up Assembly. Remove the Old Liner Take-up Assembly. Caution Observe proper electrostatic safety precautions when handling static-sensitive components such as circuit boards and printheads. Connect yourself to an antistatic device.. See Figure 5. Disconnect the liner take-up cable from P6 on the main logic board. Figure 5 Remove the Liner Take-up Spindle Assembly Cable Main logic board connector (P6) Liner take-up cable Main logic board mounting bracket 5/0/07 ZM400/ZM600 Installation Instruction 79868L-00 A

6 6 Liner Take-Up Option/Maintenance Kit Remove the Old Liner Take-up Assembly. Caution Wear protective eyewear when installing or removing E-rings, C-clips, snap rings, springs, and mounting buttons. These are under tension and could fly off. See Figure 6. Turn the printer around and remove the e-ring securing the liner take-up spindle to the shaft. Figure 6 Remove the Spindle Assembly Spindle assembly E-ring Shaft 4. Slide the spindle assembly off of the shaft L-00 A ZM400/ZM600 Installation Instruction 5/0/07

7 Liner Take-Up Option/Maintenance Kit Remove the Old Liner Take-up Assembly 7 5. See Figure 7. Remove the two mounting screws securing the liner take-up motor assembly. Figure 7 Remove the Liner Take-up Motor Assembly Liner take-up motor assembly Mounting screws () Liner take-up cable 6. Remove the liner take-up motor assembly while guiding the liner take-up cable out of the printer. 5/0/07 ZM400/ZM600 Installation Instruction 79868L-00 A

8 8 Liner Take-Up Option/Maintenance Kit Install the New Liner Take-up Assembly Install the New Liner Take-up Assembly. Caution Wear protective eyewear when installing or removing E-rings, C-clips, snap rings, springs, and mounting buttons. These are under tension and could fly off. See Figure 8. Remove and discard the tape factory install to secure the spindle assembly during shipment.. Slide the new spindle assembly from the liner take-up assembly. Figure 8 Remove the Spindle Tape, Liner take-up motor assembly Spindle 79868L-00 A ZM400/ZM600 Installation Instruction 5/0/07

9 Liner Take-Up Option/Maintenance Kit Install the New Liner Take-up Assembly 9. See Figure 9. Feed the loose end of the liner take-up cable assembly through the access hole in the base of the main frame. 4. Connect the liner take-up cable connector to P6 on the main logic board. Figure 9 Liner Take-Up Motor Access Hole Access hole Liner take-up cable 5. See Figure 7 on page 7. Slide the motor assembly towards the mainframe. 6. Align the holes in the motor assembly mounting plate with the holes in the mainframe. Secure the motor assembly with the two mounting screws provided. 7. See Figure 6 on page 6. Slide the spindle onto the shaft, and install the e-ring. 5/0/07 ZM400/ZM600 Installation Instruction 79868L-00 A

10 0 Liner Take-Up Option/Maintenance Kit Reinstall the Electronics Cover Reinstall the Electronics Cover. See Figure 0. Install the electronics cover by aligning it and sliding down, ensuring the lower flanges are inside the base and the upper flanges are between the main frame and the media door. Figure 0 Locate the Upper and Lower Flanges Electronics cover Upper flanges () Lower flanges (). See Figure on page 4. Install the four mounting screws.. See Figure on page. Open the media door. 4. Install the electronics cover mounting screw and lock washer. 5. Reinstall media and ribbon. 6. Close the media cover. 7. Reconnect the AC power cord. 8. Turn on (l) the printer L-00 A ZM400/ZM600 Installation Instruction 5/0/07

i-twin Trim Dual Blade Rechargeable Trimmer

i-twin Trim Dual Blade Rechargeable Trimmer Model VSM2A SAFETY CAUTIONS WARNING! Polythene bags over the product or packaging may be dangerous. To avoid danger of suffocation, keep away from babies and