Operator's Manual Parts List
|
|
- Kelly Rose
- 5 years ago
- Views:
Transcription
1 Operator's Manual Parts List Hammer Mill 13C Model : May 2013
2 2 13C Hammer Mill May 2013
3 TABLE OF CONTENTS SERIAL NUMBER LOCATION...4 SECTION 1 - INTRODUCTION...5 SECTION 2 - SAFETY SAFETY AT INSTALLATION GENERAL SAFETY MAINTENANCE SAFETY SAFETY DECALS SIGN-OFF FORM...8 SECTION 3 - SAFETY DECAL LOCATION...10 SECTION 4 - OPERATION TO THE NEW OPERATOR OR OWNER BREAK-IN OPERATION...13 SECTION 5 - SERVICE AND MAINTENANCE SERVICE CHECK-UPS HAMMERS CLEANING REPLACING THE HAMMERS SERVICE RECORD...15 SECTION 6 - SPECIFICATIONS BOLT TORQUE...16 Parts List Hammer Mill - First part...20 Hammer Mill - Second part...22 Hub and Hammers discharge auger kit discharge auger kit - Horizontal section discharge auger kit - Vertical section...30 Hopper (Option)...32 Warranty C Hammer Mill - May
4 SERIAL NUMBER LOCATION Always state the serial number of your Valmetal Hammer Mill when ordering parts or requesting service or other information. The serial number plate is located where indicated. Please mark the number in the space provided for easy reference. TÉL.: (819) MOD. SORTIE 170, ROUTE 20 ST-GERMAIN, DRUMMONDVILLE QUÉBEC, CANADA, J0C 1K0 SER. FABRIQUÉ AU CANADA MADE IN CANADA MODEL : SERIAL NUMBER : 4 13C Hammer Mill May 2013
5 SECTION 1 - INTRODUCTION Congratulations on your choice of a Valmetal HAMMER MILL to complement your farming operation. This equipment has been designed and manufactured to meet the needs of a discerning livestock industry. Safe, efficient and trouble free operation of your Valmetal HAMMER MILL requires that you and anyone else who will be operating or maintaining the HAMMER MILL, read and understand the Safety, Operation, Maintenance and Trouble Shooting information contained in the Operator's Manual. This manual covers the HAMMER MILL manufactured by Valmetal. Keep this manual handy for frequent reference and to pass on to new operators or owners. Call your Valmetal Dealer or Distributor if you need assistance or information. OPERATOR ORIENTATION - The directions left, right, front and rear, as mentioned throughout this manual, are as seen when facing the HAMMER MILL as shown here. 13C Hammer Mill - May
6 SECTION 2 - SAFETY SAFETY ALERT SYMBOL The Safety Alert symbol identifies important safety messages on this Valmetal equipment and in this manual. When you see this Safety Alert symbol, be alert to the possibility of personal injury or death. Follow the instructions in the safety message. This Safety Alert symbol means ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! 3 big reasons why SAFETY is so important to you? Accidents Disable and Kill, Accidents Cost, Accidents Can be avoided. Note : The use of the signal words DANGER, WARNING and CAUTION with the safety messages. The appropriate signal word for each message has been selected using the following guide-lines: DANGER CAUTION An immediate and specific hazard which WILL result in severe personal injury or death if the proper precautions are not taken. A specific hazard or unsafe practice which COULD result in severe personal injury or death if proper precautions are not taken. WARNING Unsafe practices which COULD result in personal injury if proper practices are not taken, or as a reminder of good safety practices. 6 13C Hammer Mill May 2013
7 IMPORTANT YOU are responsible for the SAFE operation and maintenance of your Valmetal vertical Mixer. YOU must ensure that you and anyone else who is going to operate, maintain or work around the machine be familiar with the operating and maintenance procedures and related SAFETY information contained in this manual. Remember, YOU are the key to safety. Good safety practices not only protect you but also the people around you. Make these practices a working part of your safety program. Be certain that EVE- RYONE operating this equipment is familiar with the recommended operating and maintenance procedures and follows all the safety precautions. Most accidents can be prevented. Do not risk injury or death by ignoring good safety practices. Mixer owners must give operating instructions to operators or employees before allowing them to operate the machine, and at least annually thereafter per OSHA regulation The most important safety device on this equipment is a SAFE operator. It is the operator's responsibility to read and understand ALL Safety and Operating instructions in the manual and to follow these. All accidents can be avoided. A person who has not read and understood all operating and safety instructions is not qualified to operate the machine. An untrained operator exposes himself and bystanders to possible serious injury or death. Do not modify the equipment in any way. Unauthorized modification may impair the function and/or safety and could affect the Iife of the machine. Think SAFETY! Work SAFELY! 2.1 SAFETY AT INSTALLATION ATTENTION! Call upon a qualified electrician to connect your HAMMER MILL. It is very important to interconnect the safety micro-switch on the door to the magnetic starter on the motor in such a way that the motor can only start when the door is closed. 2.2 GENERAL SAFETY 1. Read and understand the Operator's Manual and all safety signs before operating, maintaining, repairing, adjusting, unblocking, filling or disconnecting the HAMMER MILL. 2. Children should not be permitted in areas where machinery of this nature is operating. Switches should be locked when unit is not in use. 3. If this mill is fed by an auger or discharges into an auger, be sure auger is covered, and that shields are provided between equipment discharge and auger. 4. DANGER: Keep hands and feet out of hoppers and openings. NEVER use your hand or foot to dislodge obstructions or to push down grain or snow that may be bridged in hopper or outlets. 5. Do not poke or prod material into the mill with a bar or stick inserted through the openings while in operation. 6. Never adjust or service the unit while in operation. Keep the machine in good repair. Good maintenance is your responsibility. A poorly maintained machine is an invitation for trouble. Always use proper tools when servicing machine, making certain that they are removed from unit when service has been completed. 7. Never sit or stand on this machine. 8. Always lock out all power sources prior to adjusting or servicing the unit. 9. This Mill is equipped with shielding to protect the operator from injury. These shields can be easily removed for servicing of the unit; but should ALWAYS be replaced after the unit has been serviced. Make sure all safety shields are in place and securely fastened before start-up of the HAMMER MILL. 10. Review safety related items annually with all personnel who will be operating or maintaining the HAMMER MILL. 11. IMPORTANT! Never modify, remove or unplug the safety micro-switch on the door. It prevents the motor from starting up when the door is open. Serious injury and even death could result if this warning is not followed. The hammers are sharp rods turning at high speed. 12. Always keep hands and clothing clear of moving parts. Do 13C Hammer Mill - May
8 not wear loose-fitting clothing which may catch in moving parts. 13. Never put your hand under the auger or at the auger extremities when the motor is running. 14. Do not insert anything else but grain into the HAMMER MILL. Inserting anything else but grain in the machine may cause it to break down and may cause serious injuries. 15. Have a first aid kit available for use should the need arise and know how to use it. 16. Have a fire extinguisher available for use should the need arise and know how to use it. 2.3 MAINTENANCE SAFETY 1. Follow ALL the operating, maintenance and safety information in the manual. 2. Follow good Shop Practices: Keep service area clean and dry. Be sure electrical outlets and tools are properly grounded. Use adequate light for the job at hand. 3. Keep hands, feet, hair and clothing away from moving parts. 4. Never wear ill-fitting, baggy or frayed clothing when working around or on any of the drive system components. 5. Clear the area of bystanders, especially small children, when carrying out any maintenance and repairs or making any adjustments. 6. Do not adjust Mill when the motor is running. 7. Always lock out all power sources prior to adjusting or servicing the unit. Align the decal over the specified area and carefully press the small portion with the exposed sticky backing in place. Slowly peel back the remaining paper and carefully smooth the remaining portion of the decal in place. Small air pockets can be pierced with a pin and smoothed out using the piece of decal backing paper. 2.5 SIGN-OFF FORM Valmetal follows the general Safety Standards specified by the Society of Automotive Engineers (SAE) and the Occupational Safety and Health Administration (OSHA). Anyone who will be operating and/or maintaining the Hammer Mill must read and clearly understand ALL Safety, Operating and Maintenance information presented in this manual. Do not operate or allow anyone else to operate this equipment until such information has been reviewed. Annually review this information before the season start-up. Make these periodic reviews of SAFETY and OPERATION a standard practice for all of your equipment. We feel that an untrained operator is unqualified to operate this machine. A sign-off sheet is provided for your record keeping to show that all personnel who will be working with the equipment have read and understand the information in the Operator's Manual and have been instructed in the operation of the equipment. 2.4 SAFETY DECALS 1. Keep safety decals and signs clean and legible at all times. 2. Replace safety decals and signs that are missing or have become illegible. 3. Replaced parts that displayed a safety sign should also display the current sign. 4. Safety decals or signs are available from your Dealer Parts Department or the factory. How to install safety decals : Be sure that the installation area is clean and dry. Decide on the exact position before you remove the backing paper. Remove the smallest portion of the split backing paper. 8 13C Hammer Mill May 2013
9 SIGN-OFF FORM DATE EMPLOYEE'S SIGNATURE EMPLOYER'S SIGNATURE 13C Hammer Mill - May
10 SECTION 3 - SAFETY DECAL LOCATION The types of decals and locations on the equipment are shown in the illustration below. Good safety requires that you familiarize yourself with the various Safety Decals, the type of warning and the area, particular function related to that area, that requires your SAFETY AWARENESS. Think SAFETY! Work SAFELY! DANGER This Mill is equipped with shielding to protect the operator from injury. Cette machine est équipée de gardes de sécurité et portes d accès. Avant These shields can be easily removed to service the unit, but should de les enlever pour faire l entretien de la machine, vous DEVEZ couper ALWAYS be replaced after the unit has been serviced. ALWAYS l alimentation électrique et CADENASSER. Lorsque l opération de disconnect and lock out all power source prior to adjusting or servicing the maintenance est terminée, réinstallez tous les gardes et portes d accès unit. avant de remettre le courant. ALWAYS keep hands and clothing clear of moving parts. Do not wear loose-fitting which may catch in moving parts. Children should not be permitted in areas where machinery of this nature is operating. Switches should be locked when unit is not in use. If equipment discharges into a auger, be sure auger is covered and that shields are provided between equipment discharge and auger. DANGER: Keep hands and feetout of hoppers and openings. NEVER use your hand or foot to dislodge obstructions or to push down that may be bridged in the hopper. Do not poke or prod material into the Mill with a bar or stick inserted through the opening while in operation. Keep the machine in good condition. Good maintenance is your responsibility. A poorly maintained machine is an invitation for trouble. Always use proper tools when servicing machine, making certain that they are removed from unit when serice has been completed. NEVER adjust or service the unit while in operaion. NEVER sit or stand on this machine. Tenez les mains, les pieds, les cheveux et les vêtements loin des pièces en mouvement. Ne portez pas de vêtements amples qui risque d être happés par une pièce en mouvement. Les enfants ne devrait pas avoir la permission de s approcher des machines de cette nature lorsqu en opération. L alimentation électrique devrait être COUPÉE ET CADENASSÉE lorsque la machine n est pas en opération. Si le moulin décharge dans un convoyeur à vis, assurez-vous que la vis est couverte et que les écrans protecteurs sont placés entre l orifice de déchargement et la vis. DANGER: Ne jamais mettre les mains ou les pieds dans les trémies ou becs de déchargement. NE JAMAIS utiliser vos mains ou vos pieds pour déloger des obstructions ou pour pousser sur le grain qui peut s être ponté dans la trémie ou accumulé sur les parois. NE JAMAIS tenter de débloquer ou de pousser le matériel dans le moulin ou les vis avec une barre de métal ou un bâton lorsqu en opération. NE JAMAIS ajuster ou réparer cette machine lorsqu en oépration. Utilisez les outils appropriés et assurez-vous qu ils sont tous récupérés et rangés avant de remettre en marche. NE JAMAIS grimper ou s asseoir sur cette machine. 01A Title : Danger 8 1/2" x 5" num : 01A Title : White Valmetal 16" x 5" num : 13C REMEMBER - If Safety Decals have been damaged, removed, become illegible or parts replaced without decals, new decals must be applied. New decals are available from your authorized dealer C Hammer Mill May 2013
11 The types of decals and locations on the equipment are shown in the illustration below. Good safety requires that you familiarize yourself with the various Safety Decals, the type of warning and the area, particular function related to that area, that requires your SAFETY AWARENESS. Think SAFETY! Work SAFELY! WARNING DANGER MISE EN GARDE During the installation of the Hammer Mill, Lors de l installation de la moulange, it is of the utmost importance to connect the il est très IMPORTANT de toujours relier door s mechanical switch MICRO-SWITCH l interrupteur mécanique MICRO-SWITCH to the motor s magnetic starter in order for de la porte au démarreur magnétique du the motor to start only when the door is moteur de façon à ce que le moteur puisse closed. démarrer seulement quand la porte est fermée. Faillure to follow these instructions could result in serious injury or death. À défaut de suivre ces instructions, cela pourrait entraîner de sérieuses blessures voir même la mort. 14A Titre : Hammer Mill Installation num : 14A WARNING MOVING PART HAZARD DANGER ELECTROCUTION HAZARD 1. Have a qualified electrician provide power. 2. Keep electrical components in good repair. 3. Keep electrical components dry. RISQUE D ÉLECTROCUTION 1. Toujours avoir un électricien qualifié pour faire les connections. 2. Garder les composants électriques en bonne condition. 3. Garder les composants électriques au sec Keep hands out of machine when operating. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH AVERTISSEMENT PIÈCES EN MOUVEMENT En opération, ne pas mettre les mains dans la machine. À DÉFAUT DE SUIVRE CES INSTRUCTIONS, CELA POURRAIT ENTRAÎNER DE SÉRIEUSES BLESSURES OU MÊME LA MORT Titre : Moving Parts num : 01A Title : Electrocution Hazard num : 01A REMEMBER - If Safety Decals have been damaged, removed, become illegible or parts replaced without decals, new decals must be applied. New decals are available from your authorized dealer. 13C Hammer Mill - May
12 The types of decals and locations on the equipment are shown in the illustration below. Good safety requires that you familiarize yourself with the various Safety Decals, the type of warning and the area, particular function related to that area, that requires your SAFETY AWARENESS. Think SAFETY! Work SAFELY! DANGER ELECTROCUTION HAZARD 1. Have a qualified electrician provide power. 2. Keep electrical components in good repair. 3. Keep electrical components dry. RISQUE D ÉLECTROCUTION 1. Toujours avoir un électricien qualifié pour faire les connections. 2. Garder les composants électriques en bonne condition. 3. Garder les composants électriques au sec DANGER STAY CLEAR OF ROTATING AUGER AND KICKER. RESTEZ ÉLOIGNÉ DES VIS EN MOUVEMENT. Title : Rotating Auger num : 13C C Title : Electrocution Hazard num : 01A WARNING ROTATING PART HAZARD Keep all guards and shield in place. Keep hands, feet, hair and clothing away from moving parts. Keep others away. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH AVERTISSEMENT PIÈCES EN MOUVEMENT Garder tous les écrans protecteurs en place. Garder les mains, pieds, cheveux et vêtements éloignés des éléments mobiles et rotafifs. Garder les gens et les animaux à une distance sécuritaire de la machine. À DÉFAUT DE SUIVRE CES INSTRUCTIONS, CELA POURRAIT ENTRAÎNER DE SÉRIEUSES BLESSURES OU MÊME LA MORT Tite : Rotating Parts num : 01A WARNING MOVING PART HAZARD Keep hands out of machine when operating. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH AVERTISSEMENT PIÈCES EN MOUVEMENT En opération, ne pas mettre les mains dans la machine. À DÉFAUT DE SUIVRE CES INSTRUCTIONS, CELA POURRAIT ENTRAÎNER DE SÉRIEUSES BLESSURES OU MÊME LA MORT WARNING MISSING SHIELD HAZARD Install and secure shields before operating. Keep hands, feet, hair and clothing away from moving parts. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH AVERTISSEMENT GARDE ABSENT Installer les gardes de façon sécuritaire avant la mise en marche de la machine. Garder les mains, pieds, cheveux et vêtements éloignés des éléments mobiles. À DÉFAUT DE SUIVRE CES INSTRUCTIONS, CELA POURRAIT ENTRAÎNER DE SÉRIEUSES Title : Rotating Parts num : 01A BLESSURES OU MÊME LA MORT Title : Missing Shield num : 01A REMEMBER - If Safety Decals have been damaged, removed, become illegible or parts replaced without decals, new decals must be applied. New decals are available from your authorized dealer C Hammer Mill May 2013
13 SECTION 4 - OPERATION OPERATING SAFETY 1. Read and understand the Operator's Manual and all safety signs before operating, maintaining or adjusting the HAMMER MILL 2. Keep hands, feet, hair and clothing away from moving parts. 3. Clear the area of people, especially small children, before starting the unit. 4. Review safety related items annually with all personnel who will be operating or maintaining the HAMMER MILL. 5. Do not insert anything else but grain into the HAMMER MILL. Inserting anything else but grain in the machine may cause it to break down and may cause serious injuries. 6. Never modify, remove or unplug the safety switch located on the access door of the HAMMER MILL. This could result in serious injuries or even death. The hammers are sharp knives turning at high speed. 4.1 TO THE NEW OPERATOR OR OWNER. Valmetal HAMMER MILLS are designed to efficiently mill grain in great quantity and to convey it to destination. It is the responsibility of the owner or operator to read this manual and to train all other operators before they start working with the machine. Follow all safety instructions exactly. Safety is everyone's business. By following recommended procedures, a safe working environment is provided for the operator, bystanders and the area around the worksite. Untrained operators are not qualified to operate the machine. Many features incorporated into this machine are the result of suggestions made by customers like you. Read this manual carefully to learn how to operate the machine safely and how to set it to provide maximum efficiency. By following the operating instructions in conjunction with a good maintenance program, your HAMMER MILL will provide many years of trouble-free service 4.2 BREAK-IN Although there are no operational restrictions on the machine when used for the first time, it is recommended that the following mechanical items be checked: Before starting: Read and understand well the Operators' Manual and all safety decals. After operating for 1 hour: Check and tighten (if necessary) the three (3) hammer bolts to the proper torque. (See section 6) Check and tighten (if necessary) the bolts securing the motor. After operating for 10 hours: Follow the normal service schedule as defined in the Maintenance section. IMPORTANT Make sure all guards and protectors are well in place. Also make sure they work appropriately. Make sure the Hammer mill door is closed and locked. 4.3 OPERATION ADJUSTING THE FLOW HATCH: 1. Start Hammer mill motor. 2. Loosen the adjustment handle. 3. Slowly pull the flow hatch while making sure the normal motor amperage is not exceeded. Use an ammeter to check amperage. ATTENTION Always call upon a qualified electrician. IMPORTANT! A magnetic starter must be installed on the hammer motor. This starter must be wired to the safety switch on the door. 13C Hammer Mill - May
14 SECTION 5 - SERVICE AND MAINTENANCE MAINTENANCE SAFETY 1. Always lock out power sources in such a manner that the motor cannot be started by anyone however remote from the area, prior to adjusting or servicing. 2. Keep hands, feet, hair and clothing away from moving parts. 3. Make sure that all shields and access doors are closed and secured before operating the Hammer Mill. 4. Be careful when working near the Hammer Mill. The hammers are sharp rods turning at high speed. Never modify, remove or disconnect the safety switch located on the access door. This could result in serious injuries or death. 5.1 SERVICE CHECK-UPS Belts Every 50 hours, verify and adjust (if necessary) the belt tension on the vertical unloading auger and the horizontal auger. Motor Bolts Verify and tighten (if necessary) the bolts which hold the motor in place HAMMERS Change the motor rotation or reverse hammers every 200 hours. See section 5.2 for instructions on how to reverse hammers. We strongly advise to install, by a qualified electrician, a reverse switch on the motor to facilitate the motor rotation change. 5.2 REPLACING THE HAMMERS The hammers must be replaced when the discharge rate is reduced substantially. Follow the steps below when reversing or replacing the hammers. DANGER! Lock out all power sources prior to replacing the hammers. Note: The HAMMERMILL hub is held in place on the shaft by an SD type conical hub such as the ones used on standard pulleys. 1. Open Mill door. 2. Clean the cavity in the center of the HAMMER MILL hub. You will see six (6) hexagonal bolt heads. 3. Unscrew these bolts. The three (3) short bolts serve only to protect the HAMMER MILL hub threads. The three other bolts are screwed into the SD conical hub. Screw the three (3) long bolts into the MILL hub (in the place where were located the three (3) short bolts). Tighten them progressively and evenly until the MILL hub detaches from the conical hub. Remove the hub and hammer assembly. 4. Loosen and remove the 3 bolts (3/8 ). It is important to replace these bolts by new ones when you are replacing the hammers. Insert the hammers and spacers, fasten the 3/8 bolts and finally re-install hub on the motor shaft while making sure the key is in place. 5. To re-install, follow the same procedure but in reverse. 6. Close the Mill door CLEANING Inside Periodically clean the inside of the machine when using high-moisture corn. Magnet Clean magnet located inside the hopper or door C Hammer Mill May 2013
15 5.3 SERVICE RECORD See Maintenance section for details of service. Copy this page to continue records. ACTION CODE Check G Grease C Change L Lubricate Cl Clean Maintenance Chart Each month Cl Clean magnet. 3 months Cl Cl Clean inside of hopper. Clean inside of Mill. Tension - unloading belt. 6 months C Change motor rotation or reverse hammers. Made by (Initials) : Date dd / mm / yyyy / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / 13C Hammer Mill - May
16 SECTION 6 - SPECIFICATIONS 6.1 BOLT TORQUE CHECKING BOLT TORQUE The tables shown below give correct torque values for various bolts and capscrews. Tighten all bolts to the torques specified in chart unless otherwise noted. Check tightness of bolts periodically, using bolt torque chart as a guide. Replace hardware with the same strength bolt. ENGLISH TORQUE SPECIFICATIONS Bolt Diameter "A" Bolt Torque SAE-2 SAE-5 SAE-8 N.m. lb-pi N.m. lb-pi N.m. lb-pi 1/4" /16" /8" /16" SAE-2 SAE-5 SAE-8 1/2" /16" A 5/8" /4" /8" " METRIC TORQUE SPECIFICATIONS Bolt Diameter "A" Bolt Torque N.m. lb-pi N.m. lb-pi M M M M M M M A M M M M M M Torque figures indicated above are valid for non-greased or non-oiled threads and heads unless otherwise specified. Therefore, do not grease or oil bolts or capscrews unless otherwise specified in this manual. When using locking elements, increase torque values by 5%. * Torque value for bolts and capscrews are identified by their head markings C Hammer Mill May 2013
17 PLAN PLAN FACE FACE 56" 20 6" Ø Utility Auger To be ordered separately 12" 32" 24" 32" 24" 24" 24" 6" 40" 20" 10" Hammer Mill model " 26" 15" 102" 96" 13C Hammer Mill - May
18 18 13C Hammer Mill May 2013
19 Parts List Hammer Mill 13C Model : May 2013
20 Hammer Mill - First part See page C Hammer Mill May 2013
21 Hammer Mill - First part Item Paret No. Description Qty Housing Cover Guide Stabilizer angle (Left side) Stabilizer angle (Right side) Inlet - 4"ø Inlet - 6"ø Hub w/hammer ass y Hinge Clamp MJ7101 Limit swicth push button model C Hex. bolt 1/4"-20NC x 3/4" C Carriage bolt 3/8"-16NC x 3/4" C Hex. bolt 1/4"-20NC x 3/4" C Round head screw #10-24 x 1-3/4" C Hex. bolt 1/2"-13NC x 1" C Nylon lock nut 1/4" -20NC C Flange nut 3/8"-16NC C Nut # C Nylon lock nut 1/2"-13NC 4 13C Hammer Mill - May
22 Hammer Mill - Second part C Hammer Mill May 2013
23 Hammer Mill - Second part Item Part No. Description Qty Door Spring loaded side Catch plate Angle bracket A Circular screen - hole 1/8" A Circular screen hole 5/32" A Circular screen - hole 3/16" A Circular screen - hole 1/4" A Circular screen - hole 5/16" A Circular screen - hole 3/8" A Circular screen - hole 1/2" C Magnet Ø1" x 12 lg Spring C Hex. bolt 1/4"-20NC x 5/8" gr C Hex. bolt 1/4"-20NC x 3/4" C Socket head shoulder bolt 1/2"-13NC x 1-1/4" C Lock washer 1/4"-20NC C Washer 1/4" C Nut 3/ C Nylon lock nut 1/4" -20NC 15 13C Hammer Mill - May
24 Hub and Hammers C Hammer Mill May 2013
25 Hub and Hammers Item Part No. Description Qty Hub wo/hammer SD Hub Hammer (1x) 5-15/16" lg Hammer Set (15x) w/harware Spacer - short, Ø5/8" od x 3/8" id x lg Spacer long, Ø5/8" od x 3/8" id x lg Hex. bolt 3/8"-16NC x 5-1/2" gr.8 "Special" C Stover Nut 3/8"-16NC C Hex. Bolt 1/4"-20NC x 2" C Lock washer 1/4" 3 13C Hammer Mill - May
26 45 discharge auger kit C Hammer Mill May 2013
27 45 discharge auger kit Item Part No. Description Qty Base 1 2 VI Half-collar galvanized Access door Stabilizer angle 1 5 Utility auger (optional) F6Z Flange EFF-20J Sphérical bearing Oilite washer Thrust washer C /2" x 1" hex. Bolt C /2" nylon lock nut C /8" x 3/4" hex. Bolt 3 12A 01C /8" nylon lock nut (Not shown) C /8" flange nut C /8" x 1" hex. Bolt C /8" washer C /8" nylon lock nut Shaft - Ø1-1/4" x 8" Stabilizer angle 1 13C Hammer Mill - May
28 90 discharge auger kit - Horizontal section C Hammer Mill May 2013
29 90 discharge auger kit- Horizontal section Item Part No. Description Qty Base Auger - 6"Ø x 40-1/4" auger ass y Shaft Drive 1-1/4"Ø x 8-1/2" Shaft - 1-1/4"Ø x 8" Brass washer - 1/4"Ø Thrust washer - 1/4"Ø (Steel) Motor mount bracket Belt binder Motor mount VS-4069 Brace Motor mount plate Guard - Inside Guard - belt Adaptator - 6" Ø F6Z Flange SB Ø1-1/4" Bearing MBL117-L Pulley L-1.25 Bushing - 1 ¼"Ø MB Pulley B47 V-belt Key 3/16" x 3/16" x 1-1/4" Key 1/4" x 1/4" x 1-1/8" C Hex. bolt 5/16" x 1" gr C Hex. bolt 5/16" x 3/4" C Hex. bolt 3/8" x 3/4" gr C Hex. bolt 1/2" x 1" gr C Carriage bolt 3/8" x 1" gr C Carriage bolt 3/8" x 3/4" g2 Short Neck C Flat washer 5/16" C Nylon lock nut 3/8"-16NC C Nylon lock nut 5/16"-18NC C Nylon lock nut 1/2"-13NC C Nut 3/8"-16NC C Flange nut 3/8"-16NC C Hex. bolt 3/8" x 2-1/4" gr5 4 8 Qty C Hammer Mill - May
30 90 discharge auger kit - Vertical section C Hammer Mill May 2013
31 90 discharge auger kit- Vertical section Item Part No. Description Qty Auger tube 6"Ø x 96" Guard Belt Shaft Drive 1-1/4"Ø x 8-1/2" Auger - 6"Ø x 104" Motor mount Bearing plate Access door Elbow Adaptator - 6" flanged Adaptor VI Half-collar galvanised Leg Leg bracket Shaft - 1-1/4"Ø x 8" Thrust washer Brass washer F6Z Flange EFF-20J Spherical bearing SB Ø1-1/4" Bearing MBL117-L Pulley VI-661 Hose flexible 6"Ø L-1.25 Bushing - 1 ¼"Ø C Clamp adjustable 6"Ø MB Pulley B43 V-belt Key 3/16" x 3/16" x 1-1/4" Key 1/4" x 1/4" x 1-1/8" C Hex. bolt 3/8" x 3/4" gr C Hex. bolt 3/8" x 1" gr C Hex. bolt 3/8" x 2-1/4" gr C Hex. bolt 5/16" x 1" gr "U" bolt 3/8" x 2-3/8" x C Flat washer 3/8" C Flat washer 5/16" C Nylon lock nut 3/8"-16NC C Flange Nut 3/8"-16NC C Nylon lock nut 5/16"-18NC C Carriage bolt 3/8" x 1" gr Qty C Hammer Mill - May
32 Hopper (Option) C Hammer Mill May 2013
33 Hopper (Option) Item Part No. Description Qty Hopper - Front side Hopper - Back side Hopper - Left side Hopper - Right hopper side Nylon plate Spacer Spacer Door locking bracket Door Spacer C Knob C #10-24 x 3/8" machine screw C #10 nut C /4" x 1-1/2" hex. Bolt C /4" washer C /4" nylon lock nut C /4" x 1" hex. Bolt C #10-24 x 3/4" machine screw C /2" washer 3 13C Hammer Mill - May
34 Warranty VALMETAL INC. HAMMER MILL WARRANTY Valmetal Incorporated (Valmetal) warrants your new HAMMER MILL to be free from defects in material and workmanship, under normal use and service. Obligation under this warranty shall extend for a period of 1 year (12 months) following the date of delivery to the original purchaser and shall be limited to replacement or repair at Valmetal s choice of any parts found to be defective upon inspection by Valmetal. WARRANTY CLAIMS The purchaser claiming under this warranty shall submit a warranty claim in the prescribed form to Valmetal or an Authorized Dealer, for inspection by an authorized company representative. LIMITATIONS OF LIABILITY This warranty is expressly in lieu of all other warranties expressed or implied and all other obligations or liabilities on Valmetal s part of any kind or character, including liabilities for alleged representations or negligence. We neither assume nor authorize any other person to assume on our behalf, any liability in connection with the subsequent sale of the HAMMER MILL. This warranty shall not apply to any HAMMER MILL which has been altered outside the factory in any way if, according to Valmetal, the alterations affected the HAMMER MILL s operation and reliability, or if the hammer mill has been subject to misuse or accident. This warranty does not apply to parts that are under warranty by the original manufacturer and for which service can be obtained directly through authorized service centers. No warranty is extended to regular service items such as lubricants, belts, paint and the like. IN NO EVENT SHALL THE OWNER BE ENTITLED TO RECOVER FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES SUCH AS, BUT NOT LIMITED TO, LOSS OF CROPS, LOSS OF PROFITS OR REVENUE, OTHER COMMERCIAL LOSSES, INCONVENIENCE OR COST OF RENTAL OR REPLACEMENT EQUIPMENT. OPERATOR S MANUAL The Purchaser acknowledges having received training on safe operation of the HAMMER MILL and further acknowledges that Valmetal does not assume any liability resulting from the operation of the HAMMER MILL in any manner other than described in the Operator s Manual supplied at the time of purchase. INSPECTION PROCEDURE The magnetic starter that controls the motor on the hammer mill is connected to the safety switch installed on the hammer mill s door. Therefore the motor can not be started if the door is open. Fasteners are tight. All decals are installed. All guards are installed. Operating and safety instructions have been reviewed with customer WARRANTY VOID IF NOT REGISTERED 34 13C Hammer Mill May 2013
35 13C Hammer Mill - May
36 230 INDUSTRIAL BLVD ST-GERMAIN DE GRANTHAM QUEBEC, CANADA, J0C 1K0 PHONE: FAX: NUMBER 13C MAY 2013
37 1. Read Operator's Manual before starting. 1. Read Operator's Manual before starting. 2. Keep guards and shields in place and access 2. Keep guards and shields in place and access doors closed. doors closed. 3. Keep hands, feet, hair and clothing away from 3. Keep hands, feet, hair and clothing away from moving parts. moving parts. 4. Stop engine, place all controls in neutral, remove 4. Stop engine, place all controls in neutral, remove ignition key and wait for all moving parts to stop ignition key and wait for all moving parts to stop before servicing, adjusting, repairing or before servicing, adjusting, repairing or unplugging the machine. unplugging the machine. 5. Do not climb on the machine or place hands in 5. Do not climb on the machine or place hands in any opening when the engine is running. any opening when the engine is running. 6. Keep people and pets a safe distance from the 6. Keep people and pets a safe distance from the machine. machine. 7. Keep hydraulic lines and fittings tight, in good 7. Keep hydraulic lines and fittings tight, in good condition and free of leaks. condition and free of leaks. 8. Do not smoke when refueling. 8. Do not smoke when refueling. 9. Block up machine securely before working under 9. Block up machine securely before working under it. it. 10. Keep all electrical wires and connections dry 10. Keep all electrical wires and connections dry and In good repair. and In good repair. 11. Review safet instructions annually. 11. Review safet instructions annually TUB HAZARD Do not climb into machine when motor is running. keep others out. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. AVERTISSEMENT Ne pas monter sur la machine lorsque celle-ci est en marche. À DÉFAUT DE SUIVRE CES INSTRUCTIONS, CELA POURRAIT ENTRAÎNER DE SÉRIEUSES BLESSURES OU MÊME LE MORT CAUTION ATTENTION WARNING AVERTISSEMENT WARNING ROTATING PART HAZARD Keep all guards and shields in place. Keep hands, feet, hair and clothing away from moving parts. Keep others away. FAILURE TO FOLLOW THESE INSTRUCTIONS AVERTISSEMENT COULD RESULT IN SERIOUS INJURY OR DEATH. PIÈCE EN MOUVEMENT Garder tous les écrans protecteurs en place. Garder les mains, pieds, cheveux et vêtements éloignés des éléments mobiles et rotatifs. Garder les gens et les animaux à une distance sécuritaire de la machine. À DÉFAUT DE SUIVRE CES INSTRUCTIONS, CELA POURRAIT ENTRAÎNER DE SÉRIEUSES BLESSURES OU MÊME LE MORT HAMMER MILL 14A75 SERIES OPERATOR S MANUAL & PARTS LIST
38 VALMETAL INC. HAMMER MILL WARRANTY Valmetal Incorporated (Valmetal) warrants a new HAMMER MILL to be free from defects in material and workmanship, under normal use and service. Obligation under this warranty shall extend for a period of 1 year (12 months) following the date of delivery to the original purchaser and shall be limited to replacement or repair at Valmetal s choice of any parts found to be defective upon inspection by Valmetal. WARRANTY CLAIMS The purchaser claiming under this warranty shall submit a warranty claim in the prescribed form to Valmetal or an Authorized Dealer, for inspection by an authorized company representative. LIMITATIONS OF LIABILITY This warranty is expressly in lieu of all other warranties expressed or implied and all other obligations or liabilities on Valmetal s part of any kind or character, including liabilities for alleged representations or negligence. We neither assume nor authorize any other person to assume on our behalf, any liability in connection with the subsequent sale of the HAMMER MILL. This warranty shall not apply to any HAMMER MILL which has been altered outside the factory in any way if, according to Valmetal, the alterations affected the HAMMER MILL s operation and reliability, or if the hammer mill has been subject to misuse or accident. This warranty does not apply to parts that are under warranty by the original manufacturer and for which service can be obtained directly through authorized service centers. No warranty is extended to regular service items such as lubricants, belts, paint and the like. OPERATOR S MANUAL The Purchaser acknowledges having received training on safe operation of the HAMMER MILL and further acknowledges that Valmetal does not assume any liability resulting from the operation of the HAM- MER MILL in any manner other than described in the Operator s Manual supplied at the time of purchase. INSPECTION PROCEDURE The magnetic starter that controls the motor on the hammer mill is connected to the safety switch installed on the hammer mill s door. Therefore the motor can not be started if the door is open. Fasteners are tight. All decals are installed. All guards are installed. Operating and safety instructions have been reviewed with customer. WARRANTY VOID IF NOT REGISTERED
39 AgriMetalinc. WICKHAM, QUE., CANADA MODEL SERIE H.P. Fabriqué au Canada Made in Canada 1. Read Operator's Manual before starting. 1. Read Operator's Manual before starting. 2. Keep guards and shields in place and access 2. Keep guards and shields in place and access doors closed. doors closed. 3. Keep hands, feet, hair and clothing away from 3. Keep hands, feet, hair and clothing away from moving parts. moving parts. 4. Stop engine, place all controls in neutral, remove 4. Stop engine, place all controls in neutral, remove ignition key and wait for all moving parts to stop ignition key and wait for all moving parts to stop before servicing, adjusting, repairing or before servicing, adjusting, repairing or unplugging the machine. unplugging the machine. 5. Do not climb on the machine or place hands in 5. Do not climb on the machine or place hands in any opening when the engine is running. any opening when the engine is running. 6. Keep people and pets a safe distance from the 6. Keep people and pets a safe distance from the machine. machine. 7. Keep hydraulic lines and fittings tight, in good 7. Keep hydraulic lines and fittings tight, in good condition and free of leaks. condition and free of leaks. 8. Do not smoke when refueling. 8. Do not smoke when refueling. 9. Block up machine securely before working under 9. Block up machine securely before working under it. it. 10. Keep all electrical wires and connections dry 10. Keep all electrical wires and connections dry and In good repair. and In good repair. 11. Review safet instructions annually. 11. Review safet instructions annually TUB HAZARD Do not climb into machine when motor is running. keep others out. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. AVERTISSEMENT Ne pas monter sur la machine lorsque celle-ci est en marche. À DÉFAUT DE SUIVRE CES INSTRUCTIONS, CELA POURRAIT ENTRAÎNER DE SÉRIEUSES BLESSURES OU MÊME LE MORT SERIAL NUMBER LOCATION Always state the serial number of your Valmetal HAMMER MILL when ordering parts or requesting service or other information. The serial number plate is located where indicated. Please mark the number in the space provided for easy reference. CAUTION ATTENTION WARNING AVERTISSEMENT WARNING ROTATING PART HAZARD Keep all guards and shields in place. Keep hands, feet, hair and clothing away from moving parts. Keep others away. FAILURE TO FOLLOW THESE INSTRUCTIONS AVERTISSEMENT COULD RESULT IN SERIOUS INJURY OR DEATH. PIÈCE EN MOUVEMENT Garder tous les écrans protecteurs en place. Garder les mains, pieds, cheveux et vêtements éloignés des éléments mobiles et rotatifs. Garder les gens et les animaux à une distance sécuritaire de la machine. À DÉFAUT DE SUIVRE CES INSTRUCTIONS, CELA POURRAIT ENTRAÎNER DE SÉRIEUSES BLESSURES OU MÊME LE MORT MODEL TYPE: SERIAL NUMBER:
40 Table of contents SECTION 1 INTRODUCTION... 1 SECTION 2 SAFETY SAFETY AT INSTALLATION GENERAL SAFETY AND OPERATING SAFETY MAINTENANCE SAFETY SAFETY DECALS SIGN-OFF FORM... 6 SECTION 3 SAFETY DECAL LOCATIONS... 7 SECTION 4 OPERATION TO THE NEW OPERATOR OR OWNER MACHINE COMPONENTS BREAK-IN OPERATION ADJUSTING THE FLOW HATCH SECTION 5 SERVICE AND MAINTENANCE SERVICE CHECK-UPS HAMMERS CLEANING REPLACING THE HAMMERS SERVICE RECORD SECTION 6 SPECIFICATIONS... 16
41 AgriMetalinc. Fabriqué au Canada Made in Canada WICKHAM, QUE., CANADA MODEL SERIE H.P. 1. Read Operator's Manual before starting. 1. Read Operator's Manual before starting. 2. Keep guards and shields in place and access 2. Keep guards and shields in place and access doors closed. doors closed. 3. Keep hands, feet, hair and clothing away from 3. Keep hands, feet, hair and clothing away from moving parts. moving parts. 4. Stop engine, place all controls in neutral, remove 4. Stop engine, place all controls in neutral, remove ignition key and wait for all moving parts to stop ignition key and wait for all moving parts to stop before servicing, adjusting, repairing or before servicing, adjusting, repairing or unplugging the machine. unplugging the machine. 5. Do not climb on the machine or place hands in 5. Do not climb on the machine or place hands in any opening when the engine is running. any opening when the engine is running. 6. Keep people and pets a safe distance from the 6. Keep people and pets a safe distance from the machine. machine. 7. Keep hydraulic lines and fittings tight, in good 7. Keep hydraulic lines and fittings tight, in good condition and free of leaks. condition and free of leaks. 8. Do not smoke when refueling. 8. Do not smoke when refueling. 9. Block up machine securely before working under 9. Block up machine securely before working under it. it. 10. Keep all electrical wires and connections dry 10. Keep all electrical wires and connections dry and In good repair. and In good repair. 11. Review safet instructions annually. 11. Review safet instructions annually TUB HAZARD Do not climb into machine when motor is running. keep others out. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. MORT AVERTISSEMENT À DÉFAUT DE SUIVRE CES INSTRUCTIONS, CELA POURRAIT ENTRAÎNER DE SÉRIEUSES BLESSURES OU MÊME LE Ne pas monter sur la machine lorsque celle-ci est en marche. SECTION 1 INTRODUCTION INTRODUCTION Congratulations on your choice of a Valmetal HAMMER MILL to complement your farming operation. This equipment has been designed and manufactured to meet the needs of a discerning livestock industry. Safe, efficient and trouble free operation of your Valmetal HAMMER MILL requires that you and anyone else who will be operating or maintaining the HAMMER MILL, read and understand the Safety, Operation, Maintenance and Trouble Shooting information contained in the Operator's Manual. CAUTION ATTENTION WARNING AVERTISSEMENT WARNING ROTATING PART HAZARD Keep all guards and shields in place. Keep hands, feet, hair and clothing away from moving parts. Keep others away. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. PIÈCE EN MOUVEMENT AVERTISSEMENT Garder tous les écrans protecteurs en place. Garder les mains, pieds, cheveux et vêtements éloignés des éléments mobiles et rotatifs. Garder les gens et les animaux à une distance sécuritaire de la machine. À DÉFAUT DE SUIVRE CES INSTRUCTIONS, CELA POURRAIT ENTRAÎNER DE SÉRIEUSES BLESSURES OU MÊME LE MORT This manual covers the HAMMER MILL manufactured by Valmetal. Keep this manual handy for frequent reference and to pass on to new operators or owners. Call your Valmetal Dealer or Distributor if you need assistance or information. OPERATOR ORIENTATION - The directions left, right, front and rear, as mentioned throughout this manual, are as seen when facing the Hammer mill as shown here. 1
42 SAFETY SECTION 2 SAFETY SAFETY ALERT SYMBOL This Safety Alert symbol means ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! The Safety Alert symbol identifies important safety messages on the Valmetal HAMMER MILL and in the manual. When you see this symbol, be alert to the possibility of personal injury or death. Follow the instructions in the safety message. Why is SAFETY important to you? 3 Big Reasons Accidents Disable and Kill Accidents Cost Accidents Can be avoided Note the use of the signal words DANGER, WARNING and CAUTION with the safety messages. The appropriate signal word for each message has been selected using the following guide-lines: SIGNAL WORDS: DANGER - CAUTION - WARNING - An immediate and specific hazard which WILL result in severe personal injury or death if the proper precautions are not taken. A specific hazard or unsafe practice which COULD result in severe personal injury or death if proper precautions are not taken. Unsafe practices which COULD result in personal injury if proper practices are not taken, or as a reminder of good safety practices. ATTENTION All guards, access doors and covers must be in place and securely fastened before operating any equipment. If parts are to be inspected, cleaned, observed, or general maintenance performed, the motor driving the part or components is to be locked out electrically in such a manner that it cannot be started by anyone, however remote from the area. 2 Failure to follow these instructions may result in serious personal injury or death.
43 SAFETY IMPORTANT! YOU are responsible for the SAFE operation and maintenance of your Valmetal HAMMER MILL. YOU must ensure that you and anyone else who is going to operate, maintain or work around the HAMMER MILL be familiar with the operating and maintenance procedures and related SAFETY information contained in this manual. This manual will take you step-by-step through your working day and alerts you to all good safety practices that should be adhered to while operating the HAMMER MILL. Remember, YOU are the key to safety. Good safety practices not only protect you but also the people around you. Make these practices a working part of your safety program. Be certain that EVERYONE operating this equipment is familiar with the recommended operating and maintenance procedures and follows all the safety precautions. Most accidents can be prevented. Do not risk injury or death by ignoring good safety practices. HAMMER MILL owners must give operating instructions to operators or employees before allowing them to operate the machine, and at least annually thereafter per OSHA regulation The most important safety device on this equipment is a SAFE operator. It is the operator's responsibility to read and understand ALL Safety and Operating instructions in the manual and to follow these. All accidents can be avoided. A person who has not read and understood all operating and safety instructions is not qualified to operate the machine. An untrained operator exposes himself and bystanders to possible serious injury or death. Do not modify the equipment in any way. Unauthorized modification may impair the function and/or safety and could affect the Iife of the equipment. Think SAFETY! Work SAFELY! 2.1 SAFETY AT INSTALLATION AT INSTALLATION Call upon a qualified electrician to connect your HAMMER MILL. WARNING It is very important to interconnect the safety micro-switch on the door to the magnetic starter on the motor in such a way that the motor can only start when the door is closed. 3
44 SAFETY 2.2 GENERAL SAFETY AND OPERATING SAFETY 1. Read and understand the Operator's Manual and all safety signs before operating, maintaining, repairing, adjusting, unblocking, filling or disconnecting the HAMMER MILL. 2. Children should not be permitted in areas where machinery of this nature is operating. Switches should be locked when unit is not in use. 3. If this mill is fed by an auger or discharges into an auger, be sure auger is covered, and that shields are provided between equipment discharge and auger. 4. DANGER: Keep hands and feet out of hoppers and openings. NEVER use your hand or foot to dislodge obstructions or to push down grain or snow that may be bridged in hopper or outlets. 5. Do not poke or prod material into the mill with a bar or stick inserted through the openings while in operation. 6. Never adjust or service the unit while in operation. Keep the machine in good repair. Good maintenance is your responsibility. A poorly maintained machine is an invitation for trouble. Always use proper tools when servicing machine, making certain that they are removed from unit when service has been completed. 10. Review safety related items annually with all personnel who will be operating or maintaining the HAMMER MILL. 11. IMPORTANT! Never modify, remove or unplug the safety micro-switch on the door. It prevents the motor from starting up when the door is open. Serious injury and even death could result if this warning is not followed. The hammers are sharp rods turning at high speed. 12. Always keep hands and clothing clear of moving parts. Do not wear loose-fitting clothing which may catch in moving parts. 13. Never put your hand under the auger or at the auger extremities when the motor is running. 14. Do not insert anything else but grain into the HAMMER MILL. Inserting anything else but grain in the machine may cause it to break down and may cause serious injuries. 15. Have a first aid kit available for use should the need arise and know how to use it. 16. Have a fire extinguisher available for use should the need arise and know how to use it. 7. Never sit or stand on this machine. 8. Always lock out all power sources prior to adjusting or servicing the unit. 9. This Mill is equipped with shielding to protect the operator from injury. These shields can be easily removed for servicing of the unit; but should ALWAYS be replaced after the unit has been serviced. Make sure all safety shields are in place and securely fastened before start-up of the HAMMER MILL. 4
45 SAFETY 2.3 MAINTENANCE SAFETY 1. Follow ALL the operating, maintenance and safety information in the manual. 2. Follow good Shop Practices - Keep service area clean and dry. - Be sure electrical outlets and tools are properly grounded - Use adequate light for the job at hand 3. Keep hands, feet, hair and clothing away from moving parts. 4. Never wear ill-fitting, baggy or frayed clothing when working around or on any of the drive system components. 5. Clear the area of bystanders, especially small children, when carrying out any maintenance and repairs or making any adjustments. 6. Do not adjust Mill when the motor is running. 7. Always lock out all power sources prior to adjusting or servicing the unit. 2.4 SAFETY DECALS 1. Keep safety decals and signs clean and legible at all times. 2. Replace safety decals and signs that are missing or have become illegible. 3. Replaced parts that displayed a safety sign should also display the current sign. 4. Safety decals or signs are available from your Dealer Parts Department or the factory. How to install Safety DecaIs : * Be sure that the installation area is clean and dry. * Decide on the exact position before you remove the backing paper. * Remove the smallest portion of the split backing paper. * Align the decal over the specified area and carefully press the small portion with the exposed sticky backing in place. * Slowly peel back the remaining paper and carefully smooth the remaining portion of the decal in place. * Small air pockets can be pierced with a pin and smoothed out using the piece of decal backing paper. 5
46 SAFETY 2.5 SIGN-OFF FORM Valmetal follows the general Safety Standards specified by the Society of Automotive Engineers (SAE) and the Occupational Safety and Health Administration (OSHA). Anyone who will be operating and/or maintaining the Hammer Mill must read and clearly understand ALL Safety, Operating and Maintenance information presented in this manual. Do not operate or allow anyone else to operate this equipment until such information has been reviewed. Annually review this information before the season start-up. Make these periodic reviews of SAFETY and OPERATION a standard practice for all of your equipment. We feel that an untrained operator is unqualified to operate this machine. A sign-off sheet is provided for your record keeping to show that all personnel who will be working with the equipment have read and understand the information in the Operator's Manual and have been instructed in the operation of the equipment. SIGN-OFF FORM DATE EMPLOYEE'S SIGNATURE EMPLOYER'S SIGNATURE 6
47 Fabriqué au Canada Made in Canada 3. Keep hands, feet, hair and clothing away from moving parts. condition and free of leaks. 8. Do not smoke when refueling. and In good repair. 11. Review safet instructions annually. 3. Keep hands, feet, hair and clothing away from moving parts. condition and free of leaks. 8. Do not smoke when refueling. and In good repair. 11. Review safet instructions annually ROTATING PART HAZARD PIÈCE EN MOUVEMENT TUB HAZARD FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. Do not climb into machine when motor is running. keep others out. AVERTISSEMENT Ne pas monter sur la machine lorsque celle-ci est en marche. À DÉFAUT DE SUIVRE CES INSTRUCTIONS, CELA POURRAIT ENTRAÎNER DE SÉRIEUSES BLESSURES OU MÊME LE MORT PIÈCE EN MOUVEMENT SAFETY DECALS SECTION 3 SAFETY DECAL LOCATIONS The types of decals and locations on the equipment are shown in the illustration below. Good safety requires that you familiarize yourself with the various Safety Decals, the type of warning and the area, particular function related to that area, that requires your SAFETY AWARENESS. Think SAFETY! Work SAFELY! CAUTION 1. Read Operator's Manual before starting. 2. Keep guards and shields in place and access doors closed. 3. Keep hands, feet, hair and clothing away from moving parts. 4. Stop engine, place all controls in neutral, remove ignition key and wait for all moving parts to stop before servicing, adjusting, repairing or unplugging the machine. 5. Do not climb on the machine or place hands in any opening when the engine is running. 6. Keep people and pets a safe distance from the machine. 7. Keep hydraulic lines and fittings tight, in good condition and free of leaks. 8. Do not smoke when refueling. 9. Block up machine securely before working under it. 10. Keep all electrical wires and connections dry and In good repair. 11. Review safet instructions annually. ATTENTION 1. Lire attentivement le manuel d'opération avant la mise en marche. 2. Garder tous les écrans protecteurs en place. 3. Garder les mains, pieds, cheveux et vêtements éloignés des é1éments mobiles. 4. Arrêter le moteur, placer tous les contrôles à la position "neutre", enlever la clé de l'inition et attendre que toutes les pibces soient au point mort avant de faire tout ajustement, reparation ou de débloquer la machine. 5. Ne pas grimper sur la machine et ne jamais se placer les mains dans toute ouverture lorsque celle-ci est en marche. 6. Garder les gens et les animaux à une distance sécuritaire de la machine. 7. Garder tout boyau et fixation hydraulique en bonne condition et sans fissure. 8. Ne jamais fumer lors du plein d'essence. 9. lmmobiliser la machine de façon sécuritaire avant de travailler sous celle-ci. 10. Garder toute connection et fil électrique au sec et en bonne condition. 11. Reviser annuellement le manuel d'opération WARNING TUB HAZARD Do not climb into machine when motor is running. keep others out. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. AVERTISSEMENT AVERTISSEMENT Ne pas monter sur la machine lorsque celle-ci est en marche. À DÉFAUT DE SUIVRE CES INSTRUCTIONS, CELA POURRAIT ENTRAÎNER DE SÉRIEUSES BLESSURES OU MÊME LE MORT WARNING CAUTION ATTENTION 1. Read Operator's Manual before starting. 2. Keep guards and shields in place and access doors closed. 4. Stop engine, place all controls in neutral, remove ignition key and wait for all moving parts to stop before servicing, adjusting, repairing or unplugging the machine. 5. Do not climb on the machine or place hands in any opening when the engine is running. 6. Keep people and pets a safe distance from the machine. 7. Keep hydraulic lines and fittings tight, in good 9. Block up machine securely before working under it. 10. Keep all electrical wires and connections dry 1. Read Operator's Manual before starting. 2. Keep guards and shields in place and access doors closed. 4. Stop engine, place all controls in neutral, remove ignition key and wait for all moving parts to stop before servicing, adjusting, repairing or unplugging the machine. 5. Do not climb on the machine or place hands in any opening when the engine is running. 6. Keep people and pets a safe distance from the machine. 7. Keep hydraulic lines and fittings tight, in good 9. Block up machine securely before working under it. 10. Keep all electrical wires and connections dry WARNING AVERTISSEMENT ROTATING PART HAZARD Keep all guards and shields in place. Keep hands, feet, hair and clothing away from moving parts. Keep others away. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. AVERTISSEMENT PIÈCE EN MOUVEMENT Garder tous les écrans protecteurs en place. Garder les mains, pieds, cheveux et vêtements éloignés des éléments mobiles et rotatifs. Garder les gens et les animaux à une distance sécuritaire de la machine. À DÉFAUT DE SUIVRE CES INSTRUCTIONS, CELA POURRAIT ENTRAÎNER DE SÉRIEUSES BLESSURES OU MÊME LE MORT WARNING ROTATING PART HAZARD Keep all guards and shields in place. Keep hands, feet, hair and clothing away from moving parts. Keep others away. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. AVERTISSEMENT PIÈCE EN MOUVEMENT Garder tous les écrans protecteurs en place. Garder les mains, pieds, cheveux et vêtements éloignés des éléments mobiles et rotatifs. Garder les gens et les animaux à une distance sécuritaire de la machine. AgriMetalinc. WICKHAM, QUE., CANADA MODEL SERIE H.P. À DÉFAUT DE SUIVRE CES INSTRUCTIONS, CELA POURRAIT ENTRAÎNER DE SÉRIEUSES BLESSURES OU MÊME LE MORT WARNING Keep all guards and shields in place. Keep hands, feet, hair and clothing away from moving parts. Keep others away. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. AVERTISSEMENT Garder tous les écrans protecteurs en place. Garder les mains, pieds, cheveux et vêtements éloignés des éléments mobiles et rotatifs. Garder les gens et les animaux à une distance sécuritaire de la machine. À DÉFAUT DE SUIVRE CES INSTRUCTIONS, CELA POURRAIT ENTRAÎNER DE SÉRIEUSES BLESSURES OU MÊME LE MORT WARNING ROTATING PART HAZARD Keep all guards and shields in place. Keep hands, feet, hair and clothing away from moving parts. Keep others away. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. AVERTISSEMENT Garder tous les écrans protecteurs en place. À DÉFAUT DE SUIVRE CES INSTRUCTIONS, CELA POURRAIT ENTRAÎNER DE SÉRIEUSES BLESSURES OU MÊME LE MORT Garder les mains, pieds, cheveux et vêtements éloignés des éléments mobiles et rotatifs. Garder les gens et les animaux à une distance sécuritaire de la machine. WARNING ROTATING PART HAZARD Keep all guards and shields in place. Keep hands, feet, hair and clothing away from moving parts. Keep others away. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. PIÈCE EN MOUVEMENT AVERTISSEMENT Garder tous les écrans protecteurs en place. Garder les mains, pieds, cheveux et vêtements éloignés des éléments mobiles et rotatifs. Garder les gens et les animaux à une distance sécuritaire de la machine À DÉFAUT DE SUIVRE CES INSTRUCTIONS, CELA POURRAIT ENTRAÎNER DE SÉRIEUSES BLESSURES OU MÊME LE MORT REMEMBER - If Safety Decals have been damaged, removed, become illegible or parts replaced without decals, new decals must be applied. New decals are available from your authorized dealer. 7
48 keep others out. TUB HAZARD AVERTISSEMENT BLESSURES OU MÊME LE MORT voir même la mort SAFETY DECALS The types of decals and locations on the equipment are shown in the illustration below. Good safety requires that you familiarize yourself with the various Safety Decals, the type of warning and the area, particular function related to that area, that requires your SAFETY AWARENESS. Think SAFETY! Work SAFELY! WARNING Do not climb into machine when motor is running. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. AVERTISSEMENT Ne pas monter sur la machine lorsque celle-ci est en marche. À DÉFAUT DE SUIVRE CES INSTRUCTIONS, CELA POURRAIT ENTRAÎNER DE SÉRIEUSES WARNING During the installation of the Hammer-Mill, it is of the outmost importance to conmnect the door's mechanical switch "MICRO-SWITCH" to the motor's magnetic starter in order for the motor to start only when the door is closed. Failure to follow thses instructions could result in serious injury or death. DANGER MISE EN GARDE Lors de l'installation de la moulange, il est très IMPORTANT de toujours relier l'interrupteur mécanique "MICRO-SWITCH" de la porte au démarreur magnétique du moteur de façon à ce que le moteur puisse démarrer seulement quand la porte est fermée. À défaut de suivre ce sinstrucitons, cela purrait entraîner de sérieuses blessures voir même la mort DANGER During the installation of the Hammer-Mill, Lors de l'installation de la moulange, it is of the outmost importance to conmnect the il est très IMPORTANT de toujours relier door's mechanical switch "MICRO-SWITCH" l'interrupteur mécanique "MICRO-SWITCH" to the motor's magnetic starter in order for de la porte au démarreur magnétique du the motor to start only when the door is moteur de façon à ce que le moteur puisse closed. démarrer seulement quand la porte est fermée. Failure to follow thses instructions could result in serious injury or death. À défaut de suivre ce sinstrucitons, cela purrait entraîner de sérieuses blessures WARNING MISE EN GARDE REMEMBER - If Safety Decals have been damaged, removed, become illegible or parts replaced without decals, new decals must be applied. New decals are available from your authorized dealer. 8
49 DANGER WARNING MISE EN GARDE During the installation of the Hammer-Mill, Lors de l'installation de la moulange, it is of the outmost importance to conmnect the door's mechanical switch "MICRO-SWITCH" to the motor's magnetic starter in order for the motor to start only when the door is closed. Failure to follow thses instructions could result in serious injury or death. il est très IMPORTANT de toujours relier l'interrupteur mécanique "MICRO-SWITCH" de la porte au démarreur magnétique du moteur de façon à ce que le moteur puisse démarrer seulement quand la porte est fermée. À défaut de suivre ce sinstrucitons, cela purrait entraîner de sérieuses blessures voir même la mort. DANGER ELECTROCUTION HAZARD 1. Have a qualified electrictian provide power. 2. Keep electrical in good repair. 3. Keep electrical components dry. 3. Garder les composantes électriques au sec SAFETY DECALS The types of decals and locations on the equipment are shown in the illustration below. Good safety requires that you familiarize yourself with the various Safety Decals, the type of warning and the area, particular function related to that area, that requires your SAFETY AWARENESS. Think SAFETY! Work SAFELY! DANGER WARNING MISE EN GARDE During the installation of the Hammer-Mill, Lors de l'installation de la moulange, it is of the outmost importance to conmnect the il est très IMPORTANT de toujours relier door's mechanical switch "MICRO-SWITCH" l'interrupteur mécanique "MICRO-SWITCH" to the motor's magnetic starter in order for de la porte au démarreur magnétique du the motor to start only when the door is moteur de façon à ce que le moteur puisse closed. démarrer seulement quand la porte est fermée. Failure to follow thses instructions could result in serious injury or death. À défaut de suivre ce sinstrucitons, cela purrait entraîner de sérieuses blessures voir même la mort DANGER ELECTROCUTION HAZARD 1. Have a qualified electrictian provide power. 2. Keep electrical components in good repair. 3. Keep electrical components dry. RISQUE D'ÉLECTROCUTION 1. Toujours avoir un électricien qualifié pour faire les connections. 2. Garder les composantes électriques en bonnes condictions. 3. Garder les composantes électriques au sec RISQUE D'ÉLECTROCUTION 1. Toujours avoir un électricien qualifié pour faire les connections. 2. Garder les composantes électriques en bonnes condictions. REMEMBER - If Safety Decals have been damaged, removed, become illegible or parts replaced without decals, new decals must be applied. New decals are available from your authorized dealer. 9
50 OPERATION SECTION 4 OPERATION OPERATING SAFETY 1. Read and understand the Operator's Manual and all safety signs before operating, maintaining or adjusting the HAMMER MILL 2. Keep hands, feet, hair and clothing away from moving parts. 3. Clear the area of people, especially small children, before starting the unit. 4. Review safety related items annually with all personnel who will be operating or maintaining the HAMMER MILL. 5. Do not insert anything else but grain into the HAMMER MILL. Inserting anything else but grain in the machine may cause it to break down and may cause serious injuries. 6. Never modify, remove or unplug the safety switch located on the access door of the HAMMER MILL. This could result in serious injuries or even death. The hammers are sharp rods turning at high speed. 4.1 TO THE NEW OPERATOR OR OWNER Valmetal HAMMER MILLS are designed to efficiently mill grain in great quantity and to convey it to destination. It is the responsibility of the owner or operator to read this manual and to train all other operators before they start working with the machine. Follow all safety instructions exactly. Safety is everyone's business. By following recommended procedures, a safe working environments is provided for the operator, bystanders and the area around the worksite. Untrained operators are not qualified to operate the machine. Many features incorporated into this machine are the result of suggestions made by customers like you. Read this manual carefully to learn how to operate the machine safely and how to set it to provide maximum efficiency. By following the operating instructions in conjunction with a good maintenance program, your HAMMER MILL will provide many years of trouble-free service WARNING! Always call upon a qualified electrician. IMPOR- TANT! A magnetic starter must be installed on the hammer motor. This starter must be wired to the safety switch on the door. 10
51 TUB HAZARD Do not climb into machine when motor is running. keep others out. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. AVERTISSEMENT À DÉFAUT DE SUIVRE CES INSTRUCTIONS, CELA POURRAIT ENTRAÎNER DE SÉRIEUSES BLESSURES OU MÊME LE MORT Ne pas monter sur la machine lorsque celle-ci est en marche. 4.2 MACHINE COMPONENTS OPERATION F The HAMMER MILL is machine with a high quality/price ratio. A series of well sharpened hammers split the grains rapidly and efficiently. C B K WARNING AVERTISSEMENT E D A J A Hammer mill door B Hopper C Low level micro-switch D Flow control hatch E Unloading vertical auger F Output hose G Screen H Unloading horizontal auger I Hammer J Door safety micro-switch K Magnet Fig. 1 Machine components 11
52 OPERATION 4.3 BREAK-IN Although there are no operational restrictions on the machine when used for the first time, it is recommended that the following mechanical items be checked: A. Before starting: Read and understand well the Operators' Manual and all safety decals. B. After operating for 1 hour: - Check and tighten (if necessary) the three (3) hammer bolts to the proper torque. (See section 6) - Check and tighten (if necessary) the bolts securing the motor. C. After operating for 10 hours: Follow the normal service schedule as defined in the Maintenance section. 4.4 OPERATION ADJUSTING THE FLOW HATCH: 1. Start Hammer mill motor. 2. Loosen the adjustment handle. 3. Slowly pull the flow hatch while making sure the normal motor amperage is not exceeded. Use an ammeter to check amperage ADJUSTMENT HANDLE RULER IMPORTANT! Make sure all guards and protectors are well in place. Also make sure they work appropriately. Make sure the Hammer mill door is closed and locked. Fig. 2 Flow control hatch 12
53 TUB HAZARD Do not climb into machine when motor is running. keep others out. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. AVERTISSEMENT Ne pas monter sur la machine lorsque celle-ci est en marche. À DÉFAUT DE SUIVRE CES INSTRUCTIONS, CELA POURRAIT ENTRAÎNER DE SÉRIEUSES SERVICE & MAINTENANCE SECTION 5 SERVICE & MAINTENANCE MAINTENANCE SAFETY 1. Always lock out power sources in such a manner that the motor cannot be started by anyone however remote from the area, prior to adjusting or servicing. 2. Keep hands, feet, hair and clothing away from moving parts. 3. Make sure that all shields and access doors are closed and secured before operating the Hammer Mill. 4. Be careful when working near the Hammer Mill. The hammers are sharp rods turning at high speed. Never modify, remove or disconnect the safety switch located on the access door. This could result in serious injuries or death CLEANING 1. Inside Periodically clean the inside of the machine when using hi-moisture corn. 2. Magnet Clean magnet located inside the hopper or door. 3. Plugging If you own a Mill without hopper, the magnet in the door may become plugged. To solve this problem, install one of the two magnets on the bottom bracket as shown in figure 4. WARNING AVERTISSEMENT 5.1 SERVICE CHECK-UPS 1. Belts Every 50 hours, verify and adjust (if necessary) the belt tension on the vetical unloading auger and the horizontal auger. BLESSURES OU MÊME LE MORT Magnet 2. Motor bolt Verify and tighten (if necessary) the bolts which hold the motor shaft in place. Fig. 3 Magnet on a Mill with hopper HAMMERS Change the motor rotation or reverse hammers every 200 hours. See section 5.2 for instructions on how to reverse hammers. We strongly advise to install a reverse switch on the motor to facilitate the motor rotation change. Fig. 4 Magnet on a Mill without hopper. 13
54 SERVICE & MAINTENANCE 5.2 REPLACING THE HAMMERS The hammers must be replaced when the discharge rate is reduced substantially. Follow the steps below when reversing or replacing the hammers. Lock out all power sources prior to replacing the hammers. Note: The HAMMERMILL hub is held in place on the shaft by an SD type conical hub such as the ones used on standard pulleys. 1. Open Mill door. 2. Clean the cavity in the center of the HAMMER MILL hub. You will see six (6) hexagonal bolt heads. 3. Unscrew these bolts. The three (3) short bolts serve only to protect the HAMMER MILL hub threads. The three other bolts are screwed into the SD conical hub. Screw the three (3) long bolts into the MILL hub (in the place where were located the three (3) short bolts). Tighten them progressively and evenly until the MILL hub detaches from the conical hub. Remove the hub and hammer assembly. 4. Loosen and remove the 3 bolts (3/8"). It is important to replace these bolts by new ones when you are replacing the hammers. Insert the hammers and spacers, fasten the 3/8" bolts and finally re-install hub on the motor shaft while making sure the key is in place. 5. To re-install, follow the same procedure but in reverse. 6. Close the Mill door. Fig. 5 The hammers 14
Part No Revised April Sno Konette. Instruction Manual. Deluxe Model #1002S Standard Model #1003S. Cincinnati, OH USA
Sno Konette Part No 67933 Revised April 2009 Instruction Manual Deluxe Model #1002S Standard Model #1003S Cincinnati, OH 445241-4807 USA Sno-Konette SAFETY PRECAUTIONS INSTALLATION 2 Sno-Konette MACHINE
More informationPart No Revised: June Sno-King. Instruction Manual Model #1888. Cincinnati, OH USA
Part No. 12666 Revised: June 2009 Instruction Manual Model #1888 Cincinnati, OH 45241-4807 USA Safety Precautions Sno-King 2 Forward This manual covers the Sno-King Ice Shaver Machine, model number 1888.
More informationShaveMaster II. Block Ice Shaver Instruction Manual Model #1005. Cincinnati, OH USA. Part No Revised June 1996
Block Ice Shaver Instruction Manual Model #1005 Part No. 12354 Revised June 1996 Cincinnati, OH 45241-4807 USA SAFETY PRECAUTIONS HOW TO OPERATE THE SHAVEMASTER II MAIN SHAFT Rotates when motor is "ON".
More informationOperating Instructions
SPIN-PULL THREADED INSERT TOOL Operating Instructions Read All Safety Rules and Instructions Carefully Save this manual for Future Reference Complete Seal Kit IMPORTANT SAFETY WARNINGS: THE SAFETY WARNINGS
More informationOperating Instructions
SPIN-PULL THREADED INSERT TOOL Operating Instructions Read All Safety Rules and Instructions Carefully Save this manual for Future Reference IMPORTANT SAFETY WARNINGS: THE SAFETY WARNINGS BELOW CANNOT
More informationWorkshop Manual, Seal handbook part
Workshop Manual, Seal handbook part Mechanical seals for Large C-Pumps, L-Pumps and P-Pumps equipped with 605-series, 705-series, 805-series, 905-series drive units 894483/01 2 Seal handbook part, Large
More informationInstructions and Safety notices
VorTex High Tensile Parasol Instructions and Safety notices Note: These instructions should be delivered with the parasols and should be retained by the operator. Please ensure that these instructions
More informationPARTS LIST FOR WC-100-0ME3 WATER CANNON. Copyright 2000, Mi-T-M Corporation Issue Date:
PARTS LIST FOR WC-100-0ME3 WATER CANNON Congratulations on the purchase of your new Mi-T-M Water Cannon! This parts listing has been complied for your benefit. You can be assured your Mi-T-M Water Cannon
More informationPARTS LIST FOR WC-150-0ME3 WATER CANNON. Copyright 2000, Mi-T-M Corporation Issue Date:
PARTS LIST FOR WC-150-0ME3 WATER CANNON Congratulations on the purchase of your new Mi-T-M Water Cannon! This parts listing has been complied for your benefit. You can be assured your Mi-T-M Water Cannon
More informationLA COLLECTION THE COLLECTION
LA COLLECTION THE COLLECTION 322 323 324 325 326 327 ATTENTION La sûreté de l'appareil n'est garantie qu'en suivant scrupuleusement les instructions. Il est donc nécessaire de les conserver. Isoler l'appareil
More informationHAIRCUT KIT. 2 YEAR WARRANTY HC2000 Series USE & CARE MANUAL. To register your product go to PLEASE READ PRIOR TO USE
HAIRCUT KIT USE & CARE MANUAL PLEASE READ PRIOR TO USE To register your product go to www.remington-products.com.au 2 YEAR WARRANTY HC2000 Series IMPORTANT SAFETY INSTRUCTIONS When using an electric appliance,
More informationHAIRCUT KIT. 2 YEAR WARRANTY HC1090 Series USE & CARE MANUAL. To register your product go to PLEASE READ PRIOR TO USE
HAIRCUT KIT USE & CARE MANUAL PLEASE READ PRIOR TO USE To register your product go to www.remington-products.com.au 2 YEAR WARRANTY HC1090 Series IMPORTANT SAFETY INSTRUCTIONS When using electrical appliances,
More informationHaircut kit IMPORTANT SAFETY INSTRUCTIONS. DANGER Any appliance is. WARNING To reduce the risk PIECE
Instructions for Care and Use MODEL HC220DCSC 20 PIECE Haircut kit IMPORTANT SAFETY INSTRUCTIONS When using electrical appliances, especially basic precautions should always be followed, including the
More informationOwner s Manual. Maintenance for Pipeless (Sanijet ) 12, 13. Maintenance for Standard Pedicure Spa (Whirlpool Pump) 15, 16
Owner s Manual Table of contents 2 Introuduction & Safty Standard 3 Important considerations 4 Identify Parts & Description 5 Massage System 6 Pacific 750 Chair Assembly 7 Pacific 300 Chair Assembly 8
More information28145_HKVAC_IB 9/1/05 10:14 AM Page 1 VACUUM TRIM. Use and Care Guide HKVAC-2000
28145_HKVAC_IB 9/1/05 10:14 AM Page 1 VACUUM TRIM REVOLUTIONARY TRIMMING TECHNOLOGY Use and Care Guide HKVAC-2000 28145_HKVAC_IB 9/1/05 10:14 AM Page 2 IMPORTANT SAFETY INSTRUCTIONS Read all instructions
More information10,000 prize draw. Register online for HC5800 HC5600 HC5400. EXTRA year guarantee FREE rewards gallery
3 HC5800 HC5600 HC5400 Register online for 10,000 prize draw EXTRA year guarantee FREE rewards gallery Visit www.productregister.co.uk/remington. You must register within 28 days of purchase. Thank you
More informationWASHABLE NOSE, EAR & EYEBROW TRIMMER
WASHABLE NOSE, EAR & EYEBROW TRIMMER USE & CARE MANUAL PLEASE READ PRIOR TO USE 2 YEAR WARRANTY NE3550AU IMPORTANT SAFETY INSTRUCTIONS When using appliances, especially when children are present, basic
More informationTITANIUM ALL-IN-ONE RECHARGEABLE GROOMING SYSTEM
TITANIUM ALL-IN-ONE RECHARGEABLE GROOMING SYSTEM USE & CARE MANUAL PLEASE READ PRIOR TO USE To register your product go to www.remington-products.com.au 2 YEAR WARRANTY PG6020AU IMPORTANT SAFETY INSTRUCTIONS
More informationPOWER TOOL HAIR CUT KIT
PROFESSIONAL POWER TOOL HAIR CUT KIT USE & CARE MANUAL PLEASE READ PRIOR TO USE To register your product go to www.remington-products.com.au 5 YEAR WARRANTY HC5851AU IMPORTANT SAFETY INSTRUCTIONS When
More informationAcne Treatment USER GUIDE. Includes important safety information. Read all instructions before using device.
Acne Treatment USER GUIDE Includes important safety information. Read all instructions before using device. The revive Light Therapy Acne Treatment is intended for treatment of acne and inflammation associated
More informationULTIMATE HAIRCUT KIT 2 YEAR WARRANTY HC5005AU USE & CARE MANUAL PLEASE READ PRIOR TO USE
ULTIMATE HAIRCUT KIT USE & CARE MANUAL PLEASE READ PRIOR TO USE 2 YEAR WARRANTY HC5005AU IMPORTANT SAFETY INSTRUCTIONS When using an electric appliance, basic safety precautions should always be observed,
More informationCUTTING EDGE BEARD TRIMMER
CUTTING EDGE BEARD TRIMMER USE & CARE MANUAL PLEASE READ PRIOR TO USE 2 YEAR WARRANTY MB6025AU IMPORTANT SAFETY INSTRUCTIONS When using electrical appliances, basic precautions should always be observed,
More informationHayes Performance Systems 5800 W. Donges Bay Rd. Mequon, WI Tel: Web:
Pro & COMP Hayes Performance Systems 5800 W. Donges Bay Rd. Mequon, WI 53092 Tel: 888.686.3472 Email: techsupport@hayesbicycle.com Web: www.hayescomponents.com Hayes Components Europe Dirnismaning 20 a
More informationPDOB-II-GRM-NSF Ice Shaver. Specially designed for making shaved snow! User s Manual. Brought to you by SAC Food Supplies
GLOBAL BEAR CORP. PDOB-II-GRM-NSF Ice Shaver Specially designed for making shaved snow! User s Manual Brought to you by SAC Food Supplies Telephone: +1.714.261.6389 Email: sacfoodsupplies@gmail.com Website:
More informationUltimate Body & Bikini Kit
Ultimate Body & Bikini Kit USE & CARE MANUAL PLEASE READ PRIOR TO USE To register your product go to remington-products.com.au remington.co.nz WPG4031AU IMPORTANT SAFETY INSTRUCTIONS When using appliances,
More informationnail trimmer fast, gentle & stress free
nail trimmer fast, gentle & stress free INSTRUCTION Manual For Pets with Long Hair It is very important to Keep your Pet s Hair Out of the Way it may be best to put a stocking or sock over the paw, foot
More informationSpecially designed to create multiple styles with one powerful tool! Instruction & Styling Guide. 5-in-1 Styling Kit
Specially designed to create multiple styles with one powerful tool! SERVICE CENTre: Conair Consumer Products Inc. 100 Conair Parkway Woodbridge, ON L4H 0L2 1-800-472-7606 www.conaircanada.ca 2008 Conair
More information5-in-1 Styling Kit. Specially designed to create multiple styles with one powerful tool! Instruction & Styling Guide
Specially designed to create multiple styles with one powerful tool! SERVICE CENTre: Conair Consumer Products Inc. 100 Conair Parkway Woodbridge, ON L4H 0L2 1-800-472-7606 www.conaircanada.ca 2009 Conair
More informationMUSTACHE GROWING A BEARD AND. the manufacturer-to trim your beard and. For the best trimming results, your beard
ON/OFF SWITCH To operate, simply push slide toward blade; to stop, push slide away from blade. On/Off Switch Turbo Switch Battery Cover TURBO FEATURE This product is equipped with a turbo boost button.
More informationBODY & BIKINI KIT 2 YEAR WARRANTY WPG4020AU USE & CARE MANUAL. To register your product go to PLEASE READ PRIOR TO USE
BODY & BIKINI KIT USE & CARE MANUAL PLEASE READ PRIOR TO USE To register your product go to www.remington-products.com.au 2 YEAR WARRANTY WPG4020AU IMPORTANT SAFETY INSTRUCTIONS When using electrical appliances,
More information2/6. SASHMATE Side Hung STEEL -(series2)
2/6 SASHMATE Side Hung STEEL -(series2) CONGRATULATIONS! You have chosen a Glazesafe Ltd tool. Our aim is to provide innovative, quality tools that will make your work easier and safer. We at Glazesafe
More informationX-SYSTEM PRECISION 2 YEAR WARRANTY R3151AU USE & CARE MANUAL. To register your product go to remington-products.com.au remington.co.
X-SYSTEM PRECISION USE & CARE MANUAL PLEASE READ PRIOR TO USE To register your product go to remington-products.com.au remington.co.nz 2 YEAR WARRANTY R3151AU IMPORTANT SAFETY INSTRUCTIONS When using electrical
More informationTopdresser 1800 Workman
Form Number 3354-400 Rev A Topdresser 1800 Workman 3000/4000 Model No. 44225-260000001 and up. Parts Catalog Ordering Replacement Parts To order replacement parts, please supply the part number, the quantity,
More informationQuarter-Turn Reverse Parts Manual
1.8 (45mm), 2 (55mm), 2 1/2 (65mm), 3 (76mm), 3 1/3 (85mm) Quarter-Turn Reverse Parts Manual VHH180/VHH180RT Serial No. 180001- VHH200/VHH200RT Serial No. 110001- VHH250/VHH250RT Serial No. 210001- VHH300/VHH300RT
More informationR3150AU 2 YEAR WARRANTY. Use and Care Instruction Manual PLEASE READ PRIOR TO USE
R3150AU 2 YEAR WARRANTY Use and Care Instruction Manual PLEASE READ PRIOR TO USE IMPORTANT SAFETY INSTRUCTIONS When using an electric shaver, basic safety precautions should always be observed, including
More informationINSTRUCTION MANUAL Washbasin lifts
English Washbasin lifts 4130/4140/4170 Doc. No: M41xx Edition: 1 Date: 2008-05-06 INSTRUCTION MANUAL Washbasin lifts 4130 4140 4170 Granberg Interior AB Box 6112 SE-600 06 Norrköping SWEDEN More information:
More informationPrecisionCut Hair Clipper
PrecisionCut Hair Clipper HC5900 Register online for 10,000 prize draw EXTRA year guarantee FREE rewards gallery Visit www.remington.co.uk/productregister You must register within 28 days of purchase.
More informationPOWER PRO GROOMING KIT 2 YEAR WARRANTY USE & CARE MANUAL. To register your product go to remington-products.com.au remington.co.
POWER PRO GROOMING KIT USE & CARE MANUAL PLEASE READ PRIOR TO USE To register your product go to remington-products.com.au remington.co.nz 2 YEAR WARRANTY HC9000AU IMPORTANT SAFETY INSTRUCTIONS FOR THE
More informationDP inch Bench Mount Drill Press SETUP & OPERATION MANUAL
SETUP & OPERATION MANUAL 10 inch Bench Mount Drill Press Features 5 speeds Patented precision crosspattern laser alignment and centering guide Unique built-in LED work light illuminates the work table
More informationTITANIUM TURBO PRO HAIRCUT KIT
TITANIUM TURBO PRO HAIRCUT KIT USE & CARE MANUAL PLEASE READ PRIOR TO USE To register your product go to www.remington-products.com.au www.remington.co.nz 2 YEAR WARRANTY HC5800AU IMPORTANT SAFETY INSTRUCTIONS
More informationHOT AIR STYLER PROFESSIONAL 2 YEAR WARRANTY AD355 USE & CARE MANUAL. To register your product go to
PROFESSIONAL HOT AIR STYLER USE & CARE MANUAL PLEASE READ PRIOR TO USE To register your product go to www.remington-products.com.au 2 YEAR WARRANTY AD355 IMPORTANT SAFEGUARDS Warning: When the hot air
More information2/7 SASHMATE Top Hung-(series1)
2/7 SASHMATE Top Hung-(series1) CONGRATULATIONS! You have chosen a Glazesafe Ltd tool. Our aim is to provide innovative, quality tools that will make your work easier and safer. We at Glazesafe hope you
More informationAccident Prevention Signs & Tags
Accident Prevention Purpose This component of the Safe Work Practices is designed to provide guidance regarding OSHA Regulation 29 CFR 1910.145 Specifications for Accident Prevention Signs and Tags. Scope
More informationPRECISION PERSONAL GROOMER
PRECISION PERSONAL GROOMER USE & CARE MANUAL PLEASE READ PRIOR TO USE To register your product go to www.remington-products.com.au 2 YEAR WARRANTY PG025AU IMPORTANT SAFETY INSTRUCTIONS When using electrical
More information10XE AND 15XE Electric High-Pressure Washer
10XE AND 15XE Electric High-Pressure Washer 1-877-JD-KLEEN (1-877-535-5336) Motor Specs: 10XE 15XE Pump Oil Grade: Pump Oil Capacity: Nozzle Size: 10XE 15XE 1.5 HP / 1 Phase / 120 Volts 2.0 HP / 1 Phase
More informationOwner s Manual. Table of contents 2. Introuduction & Safty Standard 3. Important considerations 4. Identify Parts & Description 5.
Owner s Manual Table of contents 2 Introuduction & Safty Standard 3 Important considerations 4 Identify Parts & Description 5 Massage System 6 Toepia Chair Assembly 7 Toepia LX Armrest Assembly Toepia
More informationCyclone Sand Pro Debris Blower. Parts Catalog. Form Number Model No and up.
Form Number 3351-356 Cyclone Sand Pro 1000 Debris Blower Model No. 08857-240000001 and up. Parts Catalog Ordering Replacement Parts To order replacement parts, please supply the part number, the quantity,
More informationTITANIUM POWER WET/DRY SHAVER
TITANIUM POWER WET/DRY SHAVER USE & CARE MANUAL PLEASE READ PRIOR TO USE 2 YEAR WARRANTY PR1347AU IMPORTANT SAFETY INSTRUCTIONS When using electrical appliances, basic precautions should always be observed,
More informationLiner Take-Up Option/Maintenance Kit
Liner Take-Up Option/Maintenance Kit Installation Instructions This kit includes the parts and documentation necessary to install the Liner Take-up option/maintenance kit into the following printers: ZM400
More informationPerfecting Facial Trimmer
Perfecting Facial Trimmer USE & CARE MANUAL PLEASE READ PRIOR TO USE To register your product go to remington-products.com.au remington.co.nz WPG4200AU IMPORTANT SAFEGUARDS WHEN USING APPLIANCES, ESPECIALLY
More informationModel #7650 Instruction Manual Patent Pending
Model #7650 Instruction Manual Patent Pending IMPORTANT SAFEGUARDS Read all instructions before use and keep for future reference. Use shaver and accessory chargers only for their intended purpose and
More information21.0 MIA Safety Services - January 2013
Executive Summary 21.0 MIA Safety Services - January 2013 Work in the manufacturing and construction industries exposes owners and employees to the hazards of machinery or equipment with moving parts.
More informationMSA Face Protection Selection Guide. Face Protection...Simplified
MSA Face Protection Selection Guide Face Protection...Simplified How to Use This Guide 1 Conduct a Workplace Hazard Assessment. OSHA requires employers to conduct a workplace hazard assessment to determine
More informationDUAL FOIL-X 2 YEAR WARRANTY F3800AU USE & CARE INSTRUCTION MANUAL PLEASE READ PRIOR TO USE
DUAL FOIL-X USE & CARE INSTRUCTION MANUAL PLEASE READ PRIOR TO USE 2 YEAR WARRANTY F3800AU IMPORTANT SAFETY INSTRUCTIONS When using an electric shaver, basic safety precautions should always be observed,
More informationOwner s Manual & Styling Guide WARRANTY INFORMATION INSIDE
Owner s Manual & Styling Guide WARRANTY INFORMATION INSIDE Important Safety Instructions When using electrical appliances, especially when children are present, basic safety precautions should always
More informationPhilips Sonicare 2 series Plaque control plus
Philips Sonicare 2 series Plaque control plus 1 Sonicare 2 series Plaque control plus ENGLISH 6 6 ENGLISH Introduction Congratulations on your purchase and welcome to Philips! To fully benefit from the
More informationPROFESSIONAL BEARD TRIMMER
PROFESSIONAL BEARD TRIMMER USE & CARE MANUAL PLEASE READ PRIOR TO USE To register your product go to www.remington-products.com.au www.remington.co.nz 2 YEAR WARRANTY MB4130AU IMPORTANT SAFETY INSTRUCTIONS
More informationGMT180WTPBCSC BEARD/MUSTACHE TRIMMER
GMT180WTPBCSC BEARD/MUSTACHE TRIMMER Cutter Blades Blade Set TURBO SWITCH ON/OFF SWITCH with lock button Charging Light Indicator Line Cord TWO YEAR LIMITED WARRANTY Conair will repair or replace (at our
More informationSTRING LINES. If the frame is not fitted straight plumb and level the doors will not function correctly.
STRING LINES To ease installation of this frame it has been fitted with string lines. If the frame is not fitted straight plumb and level the doors will not function correctly. To ensure the top and bottom
More informationCharging base. Trimming head (30mm) on charging stand. Main body unit. On/Off switch. Indicated light. Connecting jack Connecting jack
X Thank you for your purchase. In order to make you more comfortable by using the product, please read this user manual carefully and keep it for future reference. www.dixix.com 1 Trimming head (30mm)
More informationi-twin Trim Dual Blade Rechargeable Trimmer
i-twin Trim Dual Blade Rechargeable Trimmer Model VSM2A SAFETY CAUTIONS WARNING! Polythene bags over the product or packaging may be dangerous. To avoid danger of suffocation, keep away from babies and
More informationYOUR SAFETY & INSTRUCTION MANUAL PLEASE READ CAREFULLY MANICURE GIFT SET MODEL C85004
YOUR SAFETY & INSTRUCTION MANUAL PLEASE READ CAREFULLY MANICURE GIFT SET MODEL C85004 TECHNICAL DATA Description: Model: Power: Batteries: Manicure Gift Set C85004 DC 3V 2 x AA batteries (Not Supplied)
More informationOil & Gas. Simplified Frac Iron System
Oil & Gas Simplified Frac Iron System 2 The shortest distance between two points is a straight line. Weir introduces that radical idea to the frac site. Simplicity delivered Consider the traditional frac
More informationBLUSH STYLE COLLECTION
BLUSH STYLE COLLECTION For straight hair that's sleek and shiny USE & CARE MANUAL PLEASE READ PRIOR TO USE To register your product go to www.remington-products.com.au www.remington.co.nz 2 YEAR WARRANTY
More informationBaldfader Clipper. Baldfader Clipper
Baldfader Clipper 1 Please read all instructions carefully to familiarize yourself with the Wahl Baldfader Clipper before using. Save these instructions for further reference. For any further assistance
More informationSMART EDGE ADVANCED HYBRID SHAVER
SMART EDGE ADVANCED HYBRID SHAVER USE & CARE MANUAL PLEASE READ PRIOR TO USE To register your product go to www.remington-products.com.au 2 YEAR WARRANTY XF8550AU IMPORTANT SAFETY INSTRUCTIONS When using
More informationPowerSeries Aqua. 10,000 prize draw. Register online for PR1350 PR1370. EXTRA year guarantee FREE rewards gallery
PowerSeries Aqua PR1350 PR1370 Register online for 10,000 prize draw EXTRA year guarantee FREE rewards gallery Visit www.remington.co.uk/productregister You must register within 28 days of purchase. Thank
More informationBEAUTY TRIMMER. 1 YEAR WARRANTY MPT3800 Series USE & CARE MANUAL. To register your product go to
BEAUTY TRIMMER USE & CARE MANUAL PLEASE READ PRIOR TO USE To register your product go to www.remington-products.com.au 1 YEAR WARRANTY MPT3800 Series IMPORTANT SAFEGUARDS WHEN USING APPLIANCES, ESPECIALLY
More informationLITHIUM ALL-IN-ONE BEARD TRIMMER
LITHIUM ALL-IN-ONE BEARD TRIMMER USE & CARE MANUAL PLEASE READ PRIOR TO USE To register your product go to remington-products.com.au remington.co.nz 2 YEAR WARRANTY MB6125AU IMPORTANT SAFETY INSTRUCTIONS
More informationSTERN TUBE SEAL STERN KEEPER C-TYPE MANUAL
STERN TUBE SEAL STERN KEEPER C-TYPE MANUAL C O N T E N T S CHAPTER 1 DESCRIPTION OF SAFETY 1 LIST OF WARNING 3 2 LIST OF CAUTION 4 CHAPTER 2 OUTLINE 5 1 INTRODUCTION 5 2 SPECIFICATION 5 2.1 SEAL TYPE 5
More informationKM-S824 Modern Salon Spa Pedicure Chair Plumbing Free
KM-S824 Modern Salon Spa Pedicure Chair Plumbing Free NOTE: There is a wiring harness (see arrow) that needs to be connected from under the seat cushion to the back of the Chair Back. Keller International
More information7.50. Beard Trimmer Attachment for XR1391AU SPR-XTAU $37.95 AUD N/A. Shaver Saver: Aerosol Spray Cleaner SP4 $11.95 AUD $14.95 NZD
Article Price each AUD Price each NZD Qty Amount Replacement Shaving Head & Cutters for XR1391AU SPR-XRAU $37.95 AUD $49.95 NZD Beard Trimmer Attachment for XR1391AU SPR-XTAU $37.95 AUD N/A $ Shaver Saver:
More informationPage 1 of 7. Hand-Held High Frequency C9220T
Page 1 of 7 Hand-Held High Frequency C9220T Universal Companies, Inc. 2005 All rights reserved for copyright purposes. No reproductions by print or photocopies are allowed without written permission. Page
More informationWETech PRECISION PLUS
WETech PRECISION PLUS USE & CARE MANUAL PLEASE READ PRIOR TO USE 2 YEAR WARRANTY PR1242AU IMPORTANT SAFETY INSTRUCTIONS When using electrical appliances, basic precautions should always be observed, including
More informationPositive-Turn Reverse Parts Manual
2 (55mm), 2 1/2 (65mm), 2 1/2 Short (65mm), 3 (76mm), 4 (100mm), 5 1/8 (130mm) Positive-Turn Reverse Parts Manual P1.07 VPT200 Serial No. 110001- VPT250 Serial No. 210001- VPT250 Short Serial No. 210001-
More informationBecome a Clarisonic Preferred Customer SONIC SKIN CLEANSING. One Speed. One-Year Warranty
SONIC SKIN CLEANSING One Speed One-Year Warranty Beautiful skin begins with cleaner skin. Cleaner skin begins with Clarisonic. Become a Clarisonic Preferred Customer Details on back IMPORTANT SAFEGUARDS
More informationPOWERGLIDE TITANIUM FEATURES
Model 7448TU POWERGLIDE TITANIUM The BaByliss for Men PowerGlide Titanium offers precision honed titanium cutting blades and mains operation for continuous high power to deliver an ultra smooth hair cut
More informationPreShave Power Cleanser
PreShave Power Cleanser Lift, Exfoliate and Cleanse Instructions for Use & Warranty Information Model ST247 Limited 90 Day Warranty Your Pretika product is warranted to be free from defect in material
More informationREVOLUTION M SERIES MANUAL & PARTS GUIDE
HP-M1 HP-M2 REVOLUTION M SERIES MANUAL & PARTS GUIDE NEED ASSISTANCE? If you have any issues with this product, call Iwata-Medea before returning to your place of purchase. 503-253-7308 Congratulations
More informationEasyClean 500 series
EasyClean 500 series 1 EasyClean 500 series English 4 4 English Introduction Congratulations on your purchase and welcome to Philips! To fully benefit from the support that Philips offers, register your
More informationshave care HP 6337/6336 rechargeable cordless wet/dry razors instructions for use
rechargeable cordless wet/dry razors instructions for use If you need help, answers or service, please call us at 1-800-243-7884. shave care HP 6337/6336 IMPORTANT SAFETY INSTRUCTIONS When using an electric
More informationRechargeable Tripleheader Cordless/Cord Razor 8240XL 8250XL 8251XL. Model 8240XL. Register your product and get support at
Rechargeable Tripleheader Cordless/Cord Razor 8240XL 8250XL 8251XL Register your product and get support at www.philips.com/norelco Model 8240XL 2 4 Congratulations on your purchase and welcome to Philips
More informationVOLUME PLUS AIR STYLER 2 YEAR WARRANTY AS500AU USE & CARE MANUAL. To register your product go to
VOLUME PLUS AIR STYLER USE & CARE MANUAL PLEASE READ PRIOR TO USE To register your product go to www.remington-products.com.au www.remington.co.nz 2 YEAR WARRANTY AS500AU IMPORTANT SAFEGUARDS Warning:
More informationBEFORE OPERATING THE UNIT, MUST CAREFULLY READ AND UNDERSTAND THIS MANUAL RETAIN THIS MANUAL FOR FUTURE REFERENCE IBEAR PEDICURE SPA OWNER S MANUAL
ibear Pipe-less Whirlpool Spa BEFORE OPERATING THE UNIT, MUST CAREFULLY READ AND UNDERSTAND THIS MANUAL RETAIN THIS MANUAL FOR FUTURE REFERENCE IBEAR PEDICURE SPA OWNER S MANUAL IBEAR WHIRLPOOL SPA by
More informationV-Solder BON-7103/7203
V-Solder BON-7103/7203 V-Cut solder machine (Applicable solder wire diameter φ0.3~φ0.8) Instruction manual (User s Manual) Preparation in Jyly 2010 The 7 th edition JAPAN BONKOTE CO.,LTD. Contents 1 Preface
More informationIMPORTANT SAFETY INSTRUCTIONS. Grooming System. DANGER any appliance is electrically DO NOT REACH INTO THE WATER. WARNING To reduce risk of burns,
Grooming System Have a Question? Please do not return this product to the retailer. Call Us First! Our customer service and product experts are ready to answer ALL your questions. Please call our TOLL-FREE
More informationLenis Needle-free Safety Syringe Device User Manual
Lenis Needle-free Safety Syringe Device User Manual 1 Table of Contents Welcome.3 Lenis Kit Components.4 Instructions 5-9 Maintenance and Care..10 Troubleshooting. 11 Warranty.12 Precautions 13 Return
More informationTITANIUM COMFORT PRO
TITANIUM COMFORT PRO USE & CARE MANUAL PLEASE READ PRIOR TO USE To register your product go to: www.remington-products.com.au www.remington.co.nz 2 YEAR WARRANTY PF7500AU IMPORTANT SAFETY INSTRUCTIONS
More informationEasyClean 500 series
EasyClean 500 series 1 EasyClean 500 series ENGLISH 4 4 ENGLISH Introduction Congratulations on your purchase and welcome to Philips! To fully benefit from the support that Philips offers, register your
More informationPLEASE READ PRIOR TO USE
USE & CARE INSTRUCTION MANUAL PLEASE READ PRIOR TO USE 2 YEAR WARRANTY EP7010AU IMPORTANT SAFEGUARDS Warning: Do not use this appliance near bath tubs, showers, basins or other vessels containing water.
More informationMississippi. User Manual Mounting Instructions Keep this folder with product at all times! ISIS HEIGHT ADJUSTABLE BATH
ISIS HEIGHT ADJUSTABLE BATH OpeMed (Europe) Ltd 19 Riverside Park, Farnham Surrey. GU9 7UG. United Kingdom T: +44 (0)1252 758858 F: +44 (0)870 1619681 E: info@opemed.net 40-41120-9 Mississippi User Manual
More informationTopStyler User Manual
TopStyler User Manual 2 WARNINGS: TO REDUCE THE RISK OF SERIOUS IN- JURY, READ ALL INSTRUCTIONS AND WARNINGS COMPLETELY BEFORE USING THIS PRODUCT. The TopStyler has been carefully engineered for both effectiveness
More informationBeard Trimmer. 10,000 prize draw. Register online for MB4130. EXTRA year guarantee FREE rewards gallery
Beard Trimmer MB4130 Register online for 10,000 prize draw EXTRA year guarantee FREE rewards gallery Visit www.remington.co.uk/productregister You must register within 28 days of purchase. Thank you for
More informationImportant Safety WARNING
Important Safety instructions When using electrical appliances, especially when children are present, basic safety precautions should always be followed, including the following: READ ALL INSTRUCTIONS
More informationSmart Edge / Smart Edge Pro
Smart Edge / Smart Edge Pro XF8500 XF8700 Register online for 10,000 prize draw EXTRA year guarantee FREE rewards gallery Visit www.productregister.co.uk/remington. You must register within 28 days of
More informationHyperFlex Aqua. 10,000 prize draw. Register online for XR1430 XR1450 XR1470. EXTRA year guarantee FREE rewards gallery
HyperFlex Aqua XR1430 XR1450 XR1470 Register online for 10,000 prize draw EXTRA year guarantee FREE rewards gallery Visit www.remington.co.uk/productregister. You must register within 28 days of purchase.
More informationBEARD BOSS PRO TRIMMER
BEARD BOSS PRO TRIMMER USE & CARE MANUAL PLEASE READ PRIOR TO USE To register your product go to www.remington-products.com.au www.remington.co.nz 2 YEAR WARRANTY MB4045AU IMPORTANT SAFETY INSTRUCTIONS
More informationDANGER SAVE THESE INSTRUCTIONS OPERATING INSTRUCTIONS. WARNING To reduce the risk of burns, READ ALL INSTRUCTIONS BEFORE USING KEEP AWAY FROM WATER
IMPORTANT SAFEGUARDS When using electrical appliances, especially when children are present, basic safety precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING
More information7310XL 7315XL 7325XL 7340XL 7345XL 7349XL 7350XL. Rechargeable Tripleheader Cordless/Cord Razor
Rechargeable Tripleheader Cordless/Cord Razor 7310XL 7315XL 7325XL 7340XL 7345XL 7349XL 7350XL Register your product and get support at www.philips.com/norelco 2 ENGLISH 4 7310XL/7315XL/7325XL/7340XL 7345XL/7349XL/7350XL
More informationKERATIN & ARGAN OIL NOURISH STRAIGHTENER
KERATIN & ARGAN OIL NOURISH STRAIGHTENER USE & CARE MANUAL PLEASE READ PRIOR TO USE To register your product go to www.remington-products.com.au www.remington.co.nz 2 YEAR WARRANTY S7505AU IMPORTANT SAFEGUARDS
More information