Owner s Manual. Maintenance for Pipeless (Sanijet ) 12, 13. Maintenance for Standard Pedicure Spa (Whirlpool Pump) 15, 16

Size: px

Start display at page:

Download "Owner s Manual. Maintenance for Pipeless (Sanijet ) 12, 13. Maintenance for Standard Pedicure Spa (Whirlpool Pump) 15, 16"

Theodora Francis
5 years ago
Views:

1 Owner s Manual Table of contents 2 Introuduction & Safty Standard 3 Important considerations 4 Identify Parts & Description 5 Massage System 6 Pacific 750 Chair Assembly 7 Pacific 300 Chair Assembly 8 Pacific 750 Specifications 9 Pacific 300 Specifications 10 Testing & Cleaning 11 Maintenance for Pipeless (Sanijet ) 12, 13 Maintenance for (Genijet) 14 Maintenance for Standard Pedicure Spa (Whirlpool Pump) 15, 16 Optional Discharge Pump installation guide 17 Light System 18 Disinfection your pedicure spa 19 User recommendation 20 UL 21 Back Flow Prevention Device 22 Warranty Statement 23 2

PLEASE READ AND FOLLOW INSTRUCTIONS CAREFULLY Important Pre-cautions J&A USA requires that you contact your local, qualified electrician and plumber to install your Pacific Whirlpool Pedicure Spa.

2 Introduction Thank you for purchasing the Pacific Whirlpool Pedicure Spa. This finest Whirlpool Pedicure Spa has been developed by J&A USA, Inc. to operate dependably for many years when used properly. Please take time to read this entire manual thoroughly before installation and use. PLEASE READ AND FOLLOW INSTRUCTIONS CAREFULLY Important Pre-cautions J&A USA requires that you contact your local, qualified electrician and plumber to install your Pacific Whirlpool Pedicure Spa. It cannot operate efficiently or safely unless it is provided with adequate electrical power, sufficient water pressure, proper water temperature and required drain facilities. Information on these important subjects contained in this manual. We urge you to read it carefully to make sure these requirements are met. Precautions 1 Excessive water temperature is dangerous and should be checked before use. Maximum water temperature should not exceed 100 deg. F. (38 deg. C.). 2 Always enter and exit the Whirlpool Pedicure Spa slowly and carefully. 3 Never bring and/or operate any electrical devices into or near the Whirlpool Pedicure Spa. 4 Do not stand in the whirlpool tub! 5 This Whirlpool Pedicure Spa has a weight capacity of 250lb. WARNING Do Not use if you are diabetic, have poor blood circulation, or if any area of your feet or legs are inflamed or have open wounds. Consult a physician before using if you have any kind of fungal infection, swelling, fracture, or persistent pain. Massage should be pleasant and comfortable. IF YOU EXPERIENCE PAIN OR DISCOMFORT, DISCONTINUE USE IMMEDIATELY AND CONSULT A PHYSICIAN. This product in whole is in compliance with the applicable UL LISTED standards and requirements for the US and Canada by Underwriters Laboratories Inc. Some of the components of this product are also in compliance with the applicable safety standards of the following: 3

3 Important Considerations Please read the following instructions thoroughly Inspection Please take time to inspect each pedicure spa shipment thoroughly for damages immediately upon delivery. If damages are found, it is very important to notify the freight driver and indicate extent of the damages on the bill of lading. If you fail to do so, J&A USA will not be responsible for the damages and may not be able to make appropriate claims to the freight carrier. Any damage claims must be filed directly by receiver to the freight carrier. Electrical Service Each Foot spa must have its own dedicated 115V, 60 Hz, 15 Amp GFCI protected grounded circuit. Water Supply Water supply to the Toepia pedicure spa should consist of a system that will provide both adequate water pressure and water temperature. All plumbing connections must conform to local codes. Water Pressure Normal water pressure of 30 to 120 P.S.I. is required to correctly fill the tub to the proper level. Back Flow Prevention Device - For following states: AZ, CA, CT, IL, MI, MN, NE, NV, OR, TX, WA, and WI; All Toepia pedicure spa are equipped with factory installed Dual Check Back Flow Preventer. Specification: Tested and certified to meet ANSI/ASSE standard CSA certified to standard No.B64.6 Pressure / Temperature Maximum pressure: 150 psi (10 bars) Minimum pressure: 10 psi (69kPa) Working temperature: 33F to 140F constant; intermittent to 180F (0.6C to 60C sustained; intermittent to 82.2C) Maximum recommended flow: 15 gpm (571pm) -For all other states: As an option, the Dual Check Back Flow Preventer will be factory installed. * Inquire with governing authorities for local installation requirements. Drain Facilities Connect the Foot spa drain to meet local plumbing codes. Please refer to the installation drawings on pages 9~11 Foot spa is recommended securely fastened to the floor Fasten the Foot spa with at least two fasteners. Installation Summary The installation must comply with local, state, and federal building, plumbing and electrical codes, where applicable. A licensed plumber should complete the plumbing of the pedicure spa. Note: Failure to comply with federal, state or local codes and ordinances will result in warranty being null and void. 4

4 Pacific Identify Parts on Pacific Series Message Remote Armrest Up and Down Armrest Swivel Mechanism Swivel Mechanism Foot Cushion On/Off Air Button Shower Sprayer Foot Rest Mechanism Shower Sprayer Faucet Foot Rest Mechanism On/Off Air Button Foot Cushion Faucet Pacific 750 Pacific 300 Only Available Regular Whirlpool System w/o Light One Jet Two Jets 5

5 Massage System TIMER TIME POWER POWER AUTO MASSAGE SEAT & BACK REST VIBRATION ON/OFF AUTO A FULL AUTO B BACK ROLLER SEAT ROLLER MASSAGE ON/OFF SEAT CUSHION VIBRATION ON/OFF ADJUST SPEED SPEED BACK REST VIBRATION ON/OFF 6

6 Pacific 750 Chair Assembly After Recieving Pacific 750 1) Open the packages *Do not use knife or sharp blade to open 2) Remove the Lock Nut from swivel, then Align the four bolts (swivel) to the base 3) Tighten each Locking Knob to secure the chair onto the base 4) Mount Arm Assembly (look at the seperate arm assembly instruction in the chair box) 1 2 J&A USA swivel J&A USA open package 3 4 Mounting chair onto base Locking Knob Arm Installation 7

7 Pacific 300 Chair Assembly 8

Owner s Manual. Table of contents 2. Introuduction & Safty Standard 3. Important considerations 4. Identify Parts & Description 5.

Owner s Manual. Table of contents 2. Introuduction & Safty Standard 3. Important considerations 4. Identify Parts & Description 5. Owner s Manual Table of contents 2 Introuduction & Safty Standard 3 Important considerations 4 Identify Parts & Description 5 Massage System 6 Toepia Chair Assembly 7 Toepia LX Armrest Assembly Toepia