Front Center Placket Description & Requirements. Buttonhole & Button Sewing Requirements BUTTON & BUTTONHOLE SIZES & STITCH SETTINGS
|
|
- Byron Logan
- 6 years ago
- Views:
Transcription
1 *NOTE: Interlining not shown & Top stitching may vary Two to three stitch back-tack is required at start and finish on hem. Distance of collar point length Thread nests are unacceptable. The vertical centerline of the collar band is determined by the width of the centerplacket. IE; 1 centerfront placket has a 3/4 centerline, 1 1/4 has 5/8 centerline. 3/8 The angle of the collar point buttonhole is determined by dissecting the the length of the collar s straight edge on the cape edge of the collar and scoring a dissect point. Fused Full Ply Interlining - Cut on 45 Degree Bias ng int le po ar Co ll Dissect point Buttonhole will be set back from point of collar 3/8 to outside edge of buttonhole bartack. Band height at centerfront Buttonhole should extend 1/8 past the centerline towards the outer edge of the band end. Tol is +/- 1/16 1/8 Buttonhole is to be cut from inside end tacks to tacks Buttonhole will cut through topstitching. Trim Collar face & full patch interlining at point to reduce fabric at tip Buttonhole opening (from inside end tacks) needs to be 7/16 for a 13,14, or 15 ligne size button 5/8 for a 16 or 17 ligne size button Fused Full Patch Interlining - Cut on Warp Epaulet should lay flat and must not gap between button and armhole stitching. Button must be sewn on with proper thread shank height and be lock stitched on the backside of the band. Buttonholes must be cleanly cut 3/8 Centerline of front placket (Cut on or Cut off placket shown) Not Acceptable Nosing at the start and finish of hem must align to the edge of the fronts, and not exceed 1/8. Not Acceptable Dotted Red line is showing where the top of the band sits below the cut out on the patch. The cut out allows the collar to have a clean collar break, and helps control the collar from rolling up. Excessive roping is not acceptable. COLLAR BAND BUTTON AND BUTTONHOLE PLACEMENT TWO PLY INTERLINED COLLAR REQUIREMENTS BOX PLEAT REQUIREMENTS Topstitch Tension and Formation must lay flat and be pucker free. CUT OFF FRONT PLACKET Back/Yoke Seam requires 12 to 14 Stitches Per Inch, 14 to 16 SPI on Apt 9 (if applicable). Used on all fabrics with a pattern repeat of 1/4 or more. Common or engineered centerline needs to be established prior to production. Centerline must be used on both upper and under front, so pattern repeat is consistent. Normally Interlined. Chain stitch used for Top stitch. 1/8 OR FURTHER FROM EDGE Locker Loop is to be inserted in Yoke Seam 5/16. Tolerance +0 / -1/8. D E FULL WRAP OR DOUBLE FOLD PLACKET Anchored by Buttonhole Frayed yarns must be warp yarns only. Usually stitched at outer edge of placket to secure inner cut edge of front. Can also be clean finished with no top stitch. Depending on fabric, raw edge should be secured with overlock safety stitch, if not fused. Fused interlining applied to inside edge of fold. SINGLE FOLD FRONT PLACKET Box Pleat must touch but not overlap at the center. Tolerance +/- 1/16. 13/4 Box Pleat to be proportioned equally from center of pleat to the outer edges. (Msmt. Pts. D & E) Tolerance +/- 1/16. 1 Anchored by Buttonhole 1/16 Raw edge must be secured with overlock safety stitch. Usually unlined, but can be made using a fusible interlining that is fused to the inside edge. Overlock still required. (1 Box Pleat - Example) SHOULDER EPAULET SETTING AND GRADING Bottom Hem Construction Standards Box Pleat, Yoke Seam & Locker Loop Requirements 13 TO TO 16 LINED Front Center Placket Description & Requirements 9/16 5/8 UNLINED KNIFE CUT BUTTONHOLE SIZE KNIFE CUT 3/8 9/16 3/8 7/16 5/8 7/16 Under Placket /16 5/8 7/ TO 20 3/4 9/16 11/ TO 24 13/16 13/16 5/8 5/8 3/4 13/16 9/16 5/ Applies to light weight to medium weight woven shirtings, heavier fabrics may require adjustments. Stitch counts are for Tex 24 Poly Core Poly Wrap Thread, stitch counts may need reduction if heavier tex thread used. Buttonhole and knife cut should allow button to slide easily into buttonhole but not allow if to slip out if stressed The Lined column is for components such as top centers, cuffs, neckbands, flaps and BD collars The unlined column is for components like sleeve plackets, button thru pockets, unlined front plackets or any part of the garment where interlining is not used. BUTTON & BUTTONHOLE SIZES & STITCH SETTINGS Shank Height of button attach needs to match thickness of the upper placket. Should not exceed thickness. Upper Placket Thickness Unless specified as parallel stitch, all button sewing is to be a locking cross stitch. 16 stitch count minimum Button hole should be a minimum of 1/8 longer then button. SLEEVEPLACKET & TWO BTN ADJ CUFF BUTTON PLACEMENT REQUIREMENTS SLEEVEPLACKET & CUFF BUTTON PLACEMENT REQUIREMENTS Button sewing thread tails should be trim to be no more than 1/16 in length. No looping threads or bulky thread nests Upper Placket MIN STITCH REQ 17 TO TO 22 Length of Locker Loop after inserted should be 1 7/8 Tolerance +1/4 / -0. Finished Dimensions of Locker Loop before inserted should be no less than 2 5/8 L X 1/8 W. FOLD BACK FRONT (TO THE BACK) PLACKET Also used for under front hem. Normally interlined. Chain or lock stitch used for Top stitch. Box Pleat must be centered on the back/yoke seam. (Msmt. Pts. B & C) Tolerance +/- 1/8. Straight hems or greater should have no less than 3/8 turned under. BUTTON LIGNE SIZE BUTTONHOLE SIZE LOCKER LOOP REQUIREMENTS FOR 1 PLEAT Box Pleat (A) to measure as specified on the Product Specifications. Tolerance +/- 1/16. Another option that is used is to not have any legs on the patch and to have the entire patch sit above the top of the band. COLLAR POINT BUTTONHOLE PLACEMENT Only use on solid fabric or pattern repeats of a 1/4 or less. Normally interlined. Chain stitch used for Top stitch. Button Label Yoke is to be flipped back and not caught in the Topstitch. C 1/4 or under - Hem Construction Excessive curling of hem is not acceptable. Frayed yarns must be secure by stitching. A These requirements will also apply to Inverted Box Pleats. Left and right front bottom hems should align on each other and be balanced at center. (Tolerance -+ 1/8 ) Frayed yarns must be trimmed within 1/8. B EXAMPLE: Nosing at start and finish. Bottom hems must be circular / post hemmed. Ends of Bottom hem must be closed by 1/16 SN/Edge stitch CUT ON FRONT PLACKET Top stitch on Yoke Seam is to be an Edge Stitch, not to exceed 1/16. Edge stitch must not run off. Straight hems or greater must have ends 1/16 edge stitched closed Repairs must not be visible, all thread tails must be trimmed and have no heavy concentration of back-tacking. Approx 1/8 above top of band A minimum Yoke Seam of 3/8 is required. Tail Contour must be consistent from left to right front. Tolerance 1/4 Epaulet must always be set into armhole, unless called out. Collar stitch line Epaulet should be sewn down with Armhole stitch, unless called out. Button is set on the vertical & horizontal centerline of the band. Tol is +/- 1/16 Buttonhole is to be cut from inside end tacks to tacks Buttonholes must not be recycled or double stitched Alignment notches for the patch Epaulet length from shoulder to shoulder must be maintained at the same length Tolerance +/- 1/8 BOX PLEAT, YOKE SEAM & LOCKER LOOP REQUIREMENTS 11/03/11 - SHW 3/16/10 - SHW WOVEN SHIRTING BUTTON AND BUTTONHOLE SIZES AND STITCH SETTINGS Only used on fabric that does not have a right or wrong side, not to be used on Apt 9. Normally interlined, but can be optional. Chain or Lock stitch used for top stitch. All seams must be free of frays, and broken stitches. Sewing threads should be trimmed within an 1/8. Epaulet width must be maintained from shoulder to shoulder +/- 1/16 Horizontal centerline on the band is half the distance of the band height, measured from the bottom of the band to the top of the band, parallel as shown th Inside edges of end tacks Distance between point of epaulet should be maintained on all sizes Tolerance +/- 1/4 FOLD TO THE FACE SIDE FRONT PLACKET UNDERARM SEAM UNDERARM SEAM 1 LAST BTN Button cluster center Sleeve placket button should be centered on placket opening and set in from edge so button should be set at on edge of placket. All layers will give more support and strength to the button sew. Sleeve placket buttonhole should be centered on the width of the sleeve placket and in line with the cuff buttonhole s inside end tack Knife should cut from bar to bar, no more than 1/16 left uncut inside buttonhole Width or needle throw of buttonhole stitch should be adjusted so buttonhole stitch is as close to the knife as possible to reduce frayed yarns. The needle throw may need to be adjusted due to the fabrication or thickness of the placket Minimum throw width is 3/64 5/64 width to be used on fabrics such as Knit Pique or Woven Flannels Buttonholes should be cleanly cut with no untrimmed warp or wale yarns or badly frayed weft or course yarns CROFT & BARROW DRESS SHIRTS FACE SIDE OF FABRIC 1 Buttons need to be set from the edge of the cuff regardless if one, two button adjustable or two/three stacked buttons Buttonhole should be set so the inside of the end tack is at Sleeve placket button should be centered on placket opening and set in from edge so button should be set at on edge of placket. All layers will give more support and strength to the button sew. Never set the button off the edge of the placket Buttons need to be set from the edge of the cuff regardless if one, two button adjustable or two/three stacked buttons Sleeve placket buttonhole should be centered on the width of the sleeve placket and in line with the cuff buttonhole s inside end tack. For sleeve plackets specified less then 1 in width, b hole & button should still be centered on the opening. 1 * Buttonhole should be set so the inside of the end tack is at regardless of the sleeve placket width *NOTE: Interlining not shown & Top stitching may vary *NOTE: Interlining not shown & Top stitching may vary Extra buttons sewn to face side of the under front (men s right front) Buttons should be spaced no more than 1/8 apart. Thread to match button Button Cluster centered between bottom hem and last functional front button LAST BTN THREAD POST UNDER SIDE OF FABRIC EXTRA BUTTON COUNT FOR CROFT & BARROW & APT 9 DRESS & DRESSY CASUALS All thread tails must be trimmed to be no longer then 1/8. Excessive thread nests or long loops are not acceptable. Refer to spec for extra button requirement Extra button alignment needs to be uniform Buttons to be lockstitched Buttons to be cross stitched unless two hole 16 stitch minimum Thread shanks not required on extra button LAST BTN THREAD POST UNDER SIDE OF FABRIC Button cluster center APT 9 DRESS SHIRT & DRESSY CASUALS Extra buttons sewn to under side of the under front (men s right front) Buttons should be spaced no more than 1/8 ` apart. Thread to match or blend with fabric Button cluster centered between bottom hem and last functional front button Distance between adjustable buttons on all Men s dress shirts is 3/4 Both buttons must align horizontally, Field of Tol +/- 1/8 Buttons must align horizontally to the buttonhole, Tol is 1/8 Edges of collar should align on top of each other, when properly aligned shape should not vary more t 1/16, and be consistent from side to side 2 All labeling should be centered on the fold line tolerance +/- 1/8 2 EXTRA BUTTON COUNT FOR CROFT & BARROW, HAWK SONOMA, URBAN PIPELINE, APT 9 SPORT SHIRTS BUTTON DOWN COLLAR, LONG SLEEVE = 2 LARGE & 2 SMALL BUTTON DOWN COLLAR, SHORT SLEEVE = 2 LARGE & 1 SMALL NON-BD COLLAR, LONG SLEEVE = 2 LARGE & 1 SMALL NON-BD COLLAR, SHORT SLEEVE = 2 LARGE, NO SMALL X-STITCH ATTACH BUTTON Distance between adjustable buttons on all Men s & Young Men s casual shirts is 1 X-STITCH ATTACH BUTTON Center of cluster SPORT/CASUAL SHIRTS WITH FOLD BACK UNDERFRONT HEM Extra buttons sewn to under side of the under front (men s right front) Buttons should be spaced no more than 1/4 apart. Thread to match or blend with fabric Button cluster centered between bottom hem and last functional front button If only two buttons are required, top button is centered, other is set below 2. BUTTON DOWN COLLAR, LONG SLEEVE = 1 LARGE & 2 SMALL BUTTON DOWN COLLAR, SHORT SLEEVE = 2 LARGE & 1 SMALL NON-BD COLLAR, LONG SLEEVE = 1 LARGE & 1 SMALL NON-BD COLLAR, SHORT SLEEVE = 2 LARGE, NO SMALL LAST BTN THREAD POST UNDER SIDE OF FABRIC Center of cluster 3/4 1 7/8 Pleat placement field of tolerance SPORT SHIRTS WITH DOUBLE FOLD OR SINGLE FOLD BACK FRONT PLACKETS Extra buttons sewn to under side of the under front PLACKET only, not through face side of front Buttons should be spaced no more than 1/4 apart. Thread can match button or blend with fabric Button cluster centered between bottom hem and last functional front button If only two buttons are required, top button is centered, other is set below All thread tails must be trimmed to be no longer then 1/8. Excessive thread nests or long loops are not acceptable. Refer to spec for extra button requirement Extra button alignment needs to be uniform Buttons to be lockstitched Buttons to be cross stitched unless two hole 16 stitch minimum Thread shanks not required on extra button Buttonhole & Button Sewing Requirements Cuff & Placket Two Btn Adj & Btnhole Requirements Men s Woven Dress Shirt Exra Button Requirements Men s Woven Sport Shirt Extra Button Requirements After aligning check point button placement, buttons (re-enforcement disc) must touch to be within tolerance Shoulder seams should lay on top of ea other. If they do not you must measure use the following methods to verify the the shoulder seam. 1. Measure along the bottom of the col on both sides from the center fold line t verify yoke seaming. Tolerance +/- 1/8 SLEEVE PLEATS 2. Measure along bottom of the collar o both sides from the band end to the yo seam. Tolerance +/- 1/8 POSITION OF FIRST PLEAT - 2 in from outer edge of placket - Tolerance 1/8 POSITION OF SECOND PLEAT - 2 or as specified from outer edge of placket - Tolerance 1/8 DEPTHS OF PLEATS - or as specified. - Tolerance - + 1/8 or as specified PLEATS ARE TO UNIFORM, AND SHOULD NOT OVERLAP, - Tolerance 1/8 PLEAT PLACEMENT MUST BE CONSISTENT FROM LEFT TO RIGHT SLEEVE. Cuff & Placket Button & Buttonhole Requirements 1. Sleeve Pleats Construction FOLD THE SHIRT INSIDE OUT ALIGNING THE COLLAR POINTS, THE BAND ENDS, AND THE TOP FRONT BUTTON & BUTTONHOLE. Quartering the Collar Guideline
2 Distance of collar point length 3/8 po ar Co ll Dissect point int le ng th The angle of the collar point buttonhole is determined by dissecting the the length of the collar s straight edge on the cape edge of the collar and scoring a dissect point. Buttonhole will be set back from point of collar 3/8 to outside edge of buttonhole bartack. Buttonhole will cut through topstitching. Buttonhole is to be cut from inside end tacks to tacks Buttonhole opening (from inside end tacks) needs to be 7/16 for a 13,14, or 15 ligne size button 5/8 for a 16 or 17 ligne size button Buttonholes must be cleanly cut Buttonholes must not be recycled or double stitched COLLAR POINT BUTTONHOLE PLACEMENT
3 The vertical centerline of the collar band is determined by the width of the centerplacket. IE; 1 centerfront placket has a 3/4 centerline, 1 1/4 has 5/8 centerline. Inside edges of end tacks Band height at centerfront Horizontal centerline on the band is half the distance of the band height, measured from the bottom of the band to the top of the band, parallel as shown Buttonhole should extend 1/8 past the centerline towards the outer edge of the band end. Tol is +/- 1/16 1/8 Buttonhole is to be cut from inside end tacks to tacks Button is set on the vertical & horizontal centerline of the band. Tol is +/- 1/16 Button must be sewn on with proper thread shank height and be lock stitched on the backside of the band. Centerline of front placket (Cut on or Cut off placket shown) COLLAR BAND BUTTON AND BUTTONHOLE PLACEMENT
4 Fused Full Ply Interlining - Cut on 45 Degree Bias Alignment notches for the patch Trim Collar face & full patch interlining at point to reduce fabric at tip Collar stitch line Fused Full Patch Interlining - Cut on Warp 3/8 Approx 1/8 above top of band Dotted Red line is showing where the top of the band sits below the cut out on the patch. The cut out allows the collar to have a clean collar break, and helps control the collar from rolling up. Another option that is used is to not have any legs on the patch and to have the entire patch sit above the top of the band. TWO PLY INTERLINED COLLAR REQUIREMENTS
5 Distance between point of epaulet should be maintained on all sizes Tolerance +/- 1/4 Epaulet width must be maintained from shoulder to shoulder +/- 1/16 Epaulet length from shoulder to shoulder must be maintained at the same length Tolerance +/- 1/8 Epaulet must always be set into armhole, unless called out. Epaulet should be sewn down with Armhole stitch, unless called out. Epaulet should lay flat and must not gap between button and armhole stitching. SHOULDER EPAULET SETTING AND GRADING
6 Two to three stitch back-tack is required at start and finish on hem. Thread nests are unacceptable. Sewing threads should be trimmed within an 1/8. Not Acceptable Tail Contour must be consistent from left to right front. Tolerance 1/4 Straight hems or greater must have ends 1/16 edge stitched closed Nosing at the start and finish of hem must align to the edge of the fronts, and not exceed 1/8. Not Acceptable EXAMPLE: Nosing at start and finish. Bottom hems must be circular / post hemmed. Ends of Bottom hem must be closed by 1/16 SN/Edge stitch Left and right front bottom hems should align on each other and be balanced at center. (Tolerance -+ 1/8 ) 1/4 or under - Hem Construction Excessive curling of hem is not acceptable. Excessive roping is not acceptable. Repairs must not be visible, all thread tails must be trimmed and have no heavy concentration of back-tacking. Frayed yarns must be trimmed within 1/8. Frayed yarns must be secure by stitching. Straight hems or greater should have no less than 3/8 turned under. Frayed yarns must be warp yarns only. Bottom Hem Construction Standards
7 All seams must be free of frays, and broken stitches. BOX PLEAT, YOKE SEAM & LOCKER LOOP REQUIREMENTS A minimum Yoke Seam of 3/8 is required. Top stitch on Yoke Seam is to be an Edge Stitch, not to exceed 1/16. Edge stitch must not run off. B A Label Yoke is to be flipped back and not caught in the Topstitch. C Topstitch Tension and Formation must lay flat and be pucker free. Back/Yoke Seam requires 12 to 14 Stitches Per Inch, 14 to 16 SPI on Apt 9 (if applicable). BOX PLEAT REQUIREMENTS LOCKER LOOP REQUIREMENTS FOR 1 PLEAT Locker Loop is to be inserted in Yoke Seam 5/16. Tolerance +0 / -1/8. These requirements will also apply to Inverted Box Pleats. D E Box Pleat (A) to measure as specified on the Product Specifications. Tolerance +/- 1/16. Length of Locker Loop after inserted should be 1 7/8 Tolerance +1/4 / -0. Finished Dimensions of Locker Loop before inserted should be no less than 2 5/8 L X 1/8 W. Box Pleat must be centered on the back/yoke seam. (Msmt. Pts. B & C) Tolerance +/- 1/8. Box Pleat must touch but not overlap at the center. Tolerance +/- 1/16. 13/4 Box Pleat to be proportioned equally from center of pleat to the outer edges. (Msmt. Pts. D & E) Tolerance +/- 1/ /16 (1 Box Pleat - Example) Box Pleat, Yoke Seam & Locker Loop Requirements
8 *NOTE: Interlining not shown & Top stitching may vary FOLD TO THE FACE SIDE FRONT PLACKET Only used on fabric that does not have a right or wrong side, not to be used on Apt 9. Normally interlined, but can be optional. Chain or Lock stitch used for top stitch. CUT ON FRONT PLACKET Only use on solid fabric or pattern repeats of a 1/4 or less. Normally interlined. Chain stitch used for Top stitch. CUT OFF FRONT PLACKET Used on all fabrics with a pattern repeat of 1/4 or more. Common or engineered centerline needs to be established prior to production. Centerline must be used on both upper and under front, so pattern repeat is consistent. Normally Interlined. Chain stitch used for Top stitch. 1/8 OR FURTHER FROM EDGE FOLD BACK FRONT (TO THE BACK) PLACKET Also used for under front hem. Normally interlined. Chain or lock stitch used for Top stitch. FULL WRAP OR DOUBLE FOLD PLACKET Anchored by Buttonhole Usually stitched at outer edge of placket to secure inner cut edge of front. Can also be clean finished with no top stitch. Depending on fabric, raw edge should be secured with overlock safety stitch, if not fused. Fused interlining applied to inside edge of fold. SINGLE FOLD FRONT PLACKET Anchored by Buttonhole Raw edge must be secured with overlock safety stitch. Usually unlined, but can be made using a fusible interlining that is fused to the inside edge. Overlock still required. Front Center Placket Description & Requirements
9 Button Button sewing thread tails should be trim to be no more than 1/16 in length. No looping threads or bulky thread nests Upper Placket Under Placket Shank Height of button attach needs to match thickness of the upper placket. Should not exceed thickness. Upper Placket Thickness Unless specified as parallel stitch, all button sewing is to be a locking cross stitch. 16 stitch count minimum Button hole should be a minimum of 1/8 longer then button. Knife should cut from bar to bar, no more than 1/16 left uncut inside buttonhole Width or needle throw of buttonhole stitch should be adjusted so buttonhole stitch is as close to the knife as possible to reduce frayed yarns. The needle throw may need to be adjusted due to the fabrication or thickness of the placket Minimum throw width is 3/64 5/64 width to be used on fabrics such as Knit Pique or Woven Flannels Buttonholes should be cleanly cut with no untrimmed warp or wale yarns or badly frayed weft or course yarns Buttonhole & Button Sewing Requirements
10 3/16/10 - SHW SLEEVEPLACKET & CUFF BUTTON PLACEMENT REQUIREMENTS UNDERARM SEAM 1 Sleeve placket button should be centered on placket opening and set in from edge so button should be set at on edge of placket. All layers will give more support and strength to the button sew. Buttons need to be set from the edge of the cuff regardless if one, two button adjustable or two/three stacked buttons Sleeve placket buttonhole should be centered on the width of the sleeve placket and in line with the cuff buttonhole s inside end tack Buttonhole should be set so the inside of the end tack is at X-STITCH ATTACH BUTTON Cuff & Placket Button & Buttonhole Requirements
11 11/03/11 - SHW SLEEVEPLACKET & TWO BTN ADJ CUFF BUTTON PLACEMENT REQUIREMENTS UNDERARM SEAM 1 Sleeve placket button should be centered on placket opening and set in from edge so button should be set at on edge of placket. All layers will give more support and strength to the button sew. Never set the button off the edge of the placket Buttons need to be set from the edge of the cuff regardless if one, two button adjustable or two/three stacked buttons Sleeve placket buttonhole should be centered on the width of the sleeve placket and in line with the cuff buttonhole s inside end tack. For sleeve plackets specified less then 1 in width, b hole & button should still be centered on the opening. 1 * Buttonhole should be set so the inside of the end tack is at regardless of the sleeve placket width X-STITCH ATTACH BUTTON Distance between adjustable buttons on all Men s & Young Men s casual shirts is 1 Distance between adjustable buttons on all Men s dress shirts is 3/4 Both buttons must align horizontally, Field of Tol +/- 1/8 Buttons must align horizontally to the buttonhole, Tol is 1/8 Cuff & Placket Two Btn Adj & Btnhole Requirements
12 *NOTE: Interlining not shown & Top stitching may vary CROFT & BARROW DRESS SHIRTS LAST BTN FACE SIDE OF FABRIC Button cluster center Extra buttons sewn to face side of the under front (men s right front) Buttons should be spaced no more than 1/8 apart. Thread to match button Button Cluster centered between bottom hem and last functional front button EXTRA BUTTON COUNT FOR CROFT & BARROW & APT 9 DRESS & DRESSY CASUALS BUTTON DOWN COLLAR, LONG SLEEVE = 2 LARGE & 2 SMALL BUTTON DOWN COLLAR, SHORT SLEEVE = 2 LARGE & 1 SMALL NON-BD COLLAR, LONG SLEEVE = 2 LARGE & 1 SMALL NON-BD COLLAR, SHORT SLEEVE = 2 LARGE, NO SMALL All thread tails must be trimmed to be no longer then 1/8. Excessive thread nests or long loops are not acceptable. Refer to spec for extra button requirement Extra button alignment needs to be uniform Buttons to be lockstitched Buttons to be cross stitched unless two hole 16 stitch minimum Thread shanks not required on extra button LAST BTN THREAD POST UNDER SIDE OF FABRIC Button cluster center APT 9 DRESS SHIRT & DRESSY CASUALS Extra buttons sewn to under side of the under front (men s right front) Buttons should be spaced no more than 1/8 ` apart. Thread to match or blend with fabric Button cluster centered between bottom hem and last functional front button Men s Woven Dress Shirt Exra Button Requirements
13 *NOTE: Interlining not shown & Top stitching may vary LAST BTN THREAD POST UNDER SIDE OF FABRIC Center of cluster SPORT/CASUAL SHIRTS WITH FOLD BACK UNDERFRONT HEM Extra buttons sewn to under side of the under front (men s right front) Buttons should be spaced no more than 1/4 apart. Thread to match or blend with fabric Button cluster centered between bottom hem and last functional front button If only two buttons are required, top button is centered, other is set below EXTRA BUTTON COUNT FOR CROFT & BARROW, HAWK SONOMA, URBAN PIPELINE, APT 9 SPORT SHIRTS BUTTON DOWN COLLAR, LONG SLEEVE = 1 LARGE & 2 SMALL BUTTON DOWN COLLAR, SHORT SLEEVE = 2 LARGE & 1 SMALL NON-BD COLLAR, LONG SLEEVE = 1 LARGE & 1 SMALL NON-BD COLLAR, SHORT SLEEVE = 2 LARGE, NO SMALL LAST BTN THREAD POST UNDER SIDE OF FABRIC Center of cluster SPORT SHIRTS WITH DOUBLE FOLD OR SINGLE FOLD BACK FRONT PLACKETS Extra buttons sewn to under side of the under front PLACKET only, not through face side of front Buttons should be spaced no more than 1/4 apart. Thread can match button or blend with fabric Button cluster centered between bottom hem and last functional front button If only two buttons are required, top button is centered, other is set below All thread tails must be trimmed to be no longer then 1/8. Excessive thread nests or long loops are not acceptable. Refer to spec for extra button requirement Extra button alignment needs to be uniform Buttons to be lockstitched Buttons to be cross stitched unless two hole 16 stitch minimum Thread shanks not required on extra button Men s Woven Sport Shirt Extra Button Requirements
14 2 2 3/4 1 7/8 Pleat placement field of tolerance SLEEVE PLEATS POSITION OF FIRST PLEAT - 2 in from outer edge of placket - Tolerance 1/8 POSITION OF SECOND PLEAT - 2 or as specified from outer edge of placket - Tolerance 1/8 DEPTHS OF PLEATS - or as specified. - Tolerance - + 1/8 or as specified PLEATS ARE TO UNIFORM, AND SHOULD NOT OVERLAP, - Tolerance 1/8 PLEAT PLACEMENT MUST BE CONSISTENT FROM LEFT TO RIGHT SLEEVE. Sleeve Pleats Construction
15 Edges of collar should align on top of each other, when properly aligned shape should not vary more than 1/16, and be consistent from side to side All labeling should be centered on the fold line tolerance +/- 1/ After aligning check point button placement, buttons (re-enforcement disc) must touch to be within tolerance Shoulder seams should lay on top of each other. If they do not you must measure use the following methods to verify the the shoulder seam. 1. Measure along the bottom of the collar on both sides from the center fold line to verify yoke seaming. Tolerance +/- 1/8 2. Measure along bottom of the collar on both sides from the band end to the yoke seam. Tolerance +/- 1/8 FOLD THE SHIRT INSIDE OUT ALIGNING THE COLLAR POINTS, THE BAND ENDS, AND THE TOP FRONT BUTTON & BUTTONHOLE. Quartering the Collar Guideline
16 Stitching and tip of sleeve placket must be uniformed Examples of unacceptable shaping and stitching Stitch more One side Tip off center than 1/16 lower from edge On a One piece placket care must be taken to avoid gutters and puckering 1/16 Single Needle lock Stitching on dog house stitch formation must be secure with 2 to 3 stitch backtacks. Stitching must not run off, & all thread tails are to be trimmed Button & Buttonhole centered on opening Tol +/- 1/8 Button & Buttonhole centered on width of placket Tol +/- 1/8 Placket must lay flat, no gapping between button & top or bottom of placket opening. On two piece placket, under placket must a min of 3/8 past the button sew post. Button must not sit at edge of underplacket No roping or twisting. Length of the underplacket & upper placket must be the same length Tol +/- 1/8 Underplacket must not be visible when placket & cuff are buttoned, No more than 1/16 of the underplacket Sleeve Placket Construction Requirements
17 SINGLE NEEDLE ARMHOLE Stitch line to be consistent at a 3/8 margin, or margin specified. Tolerance +-1/16. All armhole seams must be folder set with no raw edges or overlock safety stitch unless approval is given prior to sampling. SINGLE NEEDLE OR TWO NEEDLE SIDE SEAM Stitch line should be consistent on seam, and not sway. Tolerance +-1/16. Both Single Needle and Two needle stitching should be sewn on front panels with seam opening to the back. 3/8 or as specified All seams should be free of frayed fabric or threads. Frayed fabric must be locked in by the stitch, and not exceed 3/16. SLEEVE ALIGNMENT (ARMHOLE SEAM) Sleeve seam should align on all fabrications. Tolerance +- 1/4. (See Illustration to right for example) 1/4 REPAIRS Any repairs must not be visible, there should not be thread tails, no visual needle holes, or heavy concentration of threads due to backtacking. Sideseam and Armhole Construction
18 Edges of collar should align on top of each other, when properly aligned shape should not vary more than 1/16, and be consistent from side to side All labeling should be centered on the fold line tolerance +/- 1/ After aligning check point button placement, buttons (re-enforcement disc) must touch to be within tolerance Shoulder seams should lay on top of each other. If they do not you must measure use the following methods to verify the the shoulder seam. 1. Measure along the bottom of the collar on both sides from the center fold line to verify yoke seaming. Tolerance +/- 1/8 2. Measure along bottom of the collar on both sides from the band end to the yoke seam. Tolerance +/- 1/8 FOLD THE SHIRT INSIDE OUT ALIGNING THE COLLAR POINTS, THE BAND ENDS, AND THE TOP FRONT BUTTON & BUTTONHOLE. Quartering the Collar Guideline
ADDENDUM NO. 1. Please contact Ed Bonnette, CPPB, CPM, Senior Buyer at (970) with any questions regarding this addendum.
Financial Services Purchasing Division 215 N. Mason St. 2 nd Floor PO Box 580 Fort Collins, CO 80522 970.221.6775 970.221.6707 fcgov.com/purchasing ADDENDUM NO. 1 SPECIFICATIONS AND CONTRACT DOCUMENTS
More informationThe areas of a style that may be noticed right away by the customer. What is the 1st thing the customer sees?
Best Practices: Kohl s TD may add a Critical Points of Attention page to the tech pack. This calls out an area of the garment that has been identified as being visually important and should be given extra
More informationINVITATION TO BID BID FORM
INVITATION TO BID BID FORM BID NO. 2013-38 POLICE UNIFORMS City of Carlsbad Please submit Bid on or before 3:00 pm 101 N. Halagueno on June 7, 2013 in the office of Carlsbad, NM 88220 Purchasing Department,
More informationCOUNTY OF HARNETT LILLINGTON, NORTH CAROLINA
COUNTY OF HARNETT LILLINGTON, NORTH CAROLINA Harnett County Finance will receive Requests for Proposals for uniforms for its Harnett County Sheriff Department by Judy Strickland, Purchasing Agent for the
More informationRegimental Coat, Commander In Chief s Guard
Regimental Coat, Commander In Chief s Guard Guide for Construction Compiled by Judith Wicker, Revised May 1989 PLEASE READ ALL DIRECTIONS BEFORE CUTTING FABRIC! Make the lining first to check proper fit.
More informationDUBITEX TEXTILES GET DRESSED FOR WORK UNIFORM BED & BATH PROMOTIONS
www.dubitex.ae Jawad@dubitex.ae DUBITEX TEXTILES GET DRESSED FOR WORK UNIFORM BED & BATH PROMOTIONS GOING FORWARD Your Services are your livelihood. Ensure your employ look the part. We present a new line
More informationClothing showcase INFORMATION ON. Clothing and Textile Showcase OBJECTIVES
INFORMATION ON Clothing and Textile Showcase D E L A W A R E 4 - H Clothing showcase The 4-H Clothing and Textiles Showcase is a contest open to all 4-H members currently enrolled in the Clothing or Exploring
More informationMADE to MEASURE BLOUSE. Version S12
MADE to MEASURE BLOUSE Version S12 WINDSOR KING LONDON KENT Collar with 1 button collar depths 30, 35 and 40 mm Collars with 2 buttons collar depths 40, 45 and 50 mm only Collars with 3 buttons collar
More informationA few notes about PDF patterns from Designs by Jude...
A few notes about PDF patterns from.... This PDF pattern requires legal size paper (8.5 x 14 ) or A4 size paper (8.27 x 11.69, 210mm x 297mm). It will not print on standard letter. Patterns containing
More informationPrinted: 15 AUG :02 AM. Page 1 of 12 BRACLET SLV FANCY STRIPE GALLERY CABLE SHIFT DRESS. 09 Cable as Swatch
7406877 Folder Summary - Apparel Sweaters Dresses (06) 70%NYLON 0%LAMBSWOOL Agent: Pre-Dev Vendor: Vendor: Li Fung Style Reference: Range: XS-XL Li Fung Stitch Reference: Technical Designer: Olena Wallerand
More informationFit Sample / 1st Submit Cover Page
Fit Sample / 1st Submit Cover Page TD Submit Due Date Received By Received Date Reviewed By Reviewed Date Approved By Approved Date Agent REJECTED 3/5/2013 EVER MELLOW By Date Received Weight Weight Ship
More informationA few notes about PDF patterns from Designs by Jude...
A few notes about PDF patterns from Designs by Jude.... This PDF pattern requires legal size paper (8.5 x 14 ) or A4 size paper (8.27 x 11.69, 210mm x 297mm). It will not print on standard letter. Patterns
More informationA few notes about PDF patterns from Designs by Jude...
A few notes about PDF patterns from.... This PDF pattern requires legal size paper (8.5 x 14 ) or A4 size paper (8.27 x 11.69, 210mm x 297mm). It will not print on standard letter. Patterns containing
More informationPUBLIC NOTICE. Bids will be received by the City until 2:10 p.m., September 17, 2010, at which time they will be opened and read aloud.
PUBLIC NOTICE The Pigeon Forge Police Department is requesting bids from qualified vendors for Police Officer uniforms. Bid specifications may be obtained at the Pigeon Forge Police Department Monday through
More informationSEWING *STATE FAIR PROJECT* THESE REQUIREMENTS SUPERSEDE YOUR PROJECT MANUAL.
SEWING *STATE FAIR PROJECT* THESE REQUIREMENTS SUPERSEDE YOUR PROJECT MANUAL. You have until May 15 to add or drop this project from your current year s enrollment. Sewing will be divided by member s current
More informationNotes: Chest and waist measurement taken with the garment closed on the flat
Jackets Size 38R MMT Centre back length 75.5 Chest 2.5 below the armhole ( front edge including wr 53.5 (front edge including wrap to 48.5 cuff 65 Across shoulders 46.5 Trousers Size 32 MMT Waist width
More informationRUGBY. The best LAUNCH. What makes our jerseys the best? What makes our jerseys the best? UNIFORMS. NEW! Titan Fabric LEAGUE & UNION 2012 RANGE
LEAGUE & UNION REINFORCEMENTS! What makes our jerseys the best? What makes our jerseys the best? datasheet pages 4-5 datasheet pages 4-5 Probably The best RUGBY UNIFORMS in the world! NEW! Titan Fabric
More informationPatternMaker Outerwear Garment Macros
Home page Svensk manual Suomeksi PatternMaker dealers Counter started 2000-01-01 Site Map December 5th, 2001 PatternMaker Pattern Drafting Sofware for PC Versions & prices Download & buy Demo version Macro
More informationCOLOMBINE Maxi dress with ruffles
COLOMBINE Maxi dress with ruffles Maxi dress with ruffled straps or full back based on the Colombine pattern Sizes 2, 3,, 6, 8 and 10 1 FOREWORD In order to sew this version of Colombine, you must own
More informationZip Attachments and Fasteners. Introduction to Zips.(Refer to Single Page Visual) Types of zips
Zip Attachments and Fasteners. Introduction to Zips.(Refer to Single Page Visual) Types of zips There are three basic types of zips: conventional, opened, and concealed. Conventional zips are closed at
More informationOrganza This delicate fabric adds weightless support to your garments without increasing bulk
The Secret Strength of Silk Organza This delicate fabric adds weightless support to your garments without increasing bulk B y M a r l a K a z e l l ( f r o m i s s u e # 1 2 4 ) If you envision frilly
More informationThe Makers Customized
The Makers Customized Men Model Manual The Makers Customized Version 6-11-2016 1 Full option models 2 Full option jackets Model Paris Slim silhouette Higher armhole Soft Pagode shoulder Small sleeve-head
More informationHow to Make a Basic Skirt
How to Make a Basic Skirt By: burdastyle http://www.burdastyle.com/projects/how-to-make-a-basic-skirt This tutorial walks you through how to draft a basic one-dart skirt sloper. This exercise can lead
More informationNotice is hereby given of the following change and Questions and Responses to the above referenced RFP:
FLORIDA DEPARTMENT OF TRANSPORTATION Procurement Office 605 Suwannee Street, MS 20 Tallahassee, Florida 32399-0450 Phone: (850) 414-4568 Fax: (850) 414-4951 ADDENDUM NO. 2 DATE: October 10, 2013 RE: RFP
More informationFOLD METHOD F04 SHORT CAPE/DOLMAN JACKET (SINGLE OR DOUBLE BREASTED) FOLD METHOD F05B COATS (SINGLE OR DOUBLE BREASTED)...
Section 11 APPAREL PRODUCT PACKAGING- Apparel AUGUST 2016 1 CONTACTS & GENERAL GUIDELINES... 3 FLAT PACKAGING - PROCEDURES... 5 IDENTIFICATION INFORMATION (FOR GARMENT ON HANGER PRODUCT ONLY)... 6 FOLD
More informationSears Holdings Management Corporation FLOOR READY GUIDELINES
Sears Holdings Management Corporation FLOOR READY GUIDELINES 2007 Sears Brands, LLC April 2007 ACCESSORIES Headwear - Hats, Visors, Caps All Categories ACC.HTS.CPS.VSR.01 HATS: Insert MAIN label into interior
More informationITEM: COAT, LONG CLOTH -PRESCRIBED WORN BY: STYLE: ! CHICAGO POLICE DEPARTMENT
! CHICAGO POLICE DEPARTMENT IDATE OF ISSUE/REVISION SPECIFICATION NO. j UNIFORM & EQUIPl'nENT SPECIFICATIONS i RESEARCH & DEVELOPMENT DIVISION March 1985 3.1502 ITEM: COAT, LONG CLOTH -PRESCRIBED WORN
More informationAction Sports Systems Inc. P.O. Box 1442, Morganton, NC 28680
Mens & Youth Custom Football Uniforms Durable Designs Delivered on-time for over 25 years Orders: 800-631-1091 Fax: 828-584-8440 Phone: 828-584-8000 sales@actionsportsuniforms. Please ask for our other
More informationBIZ CORPORATES BOULEVARD STYLE
BIZ CORPORATES 2017 WWW.BIZCORPORATES.COM BOULEVARD STYLE ISSUE No. 01 FEEL THE DIFFERENCE FEEL THE DIFFERENCE CONTENTS WITH A FOCUS ON AUTHENTICITY AND QUALITY, THE BOULEVARD RANGE REVEALS UNIQUE SHIRTING
More informationGarment Assembly & Finishing: Pieces into Products Garment assembly PIECE ASSEMBLY Construction collars Collars Collars Collars - Quality
1 2 3 4 5 6 7 8 9 10 Garment Assembly & Finishing: Pieces into Products Chapter 12 Garment assembly Pieces + pieces = products Partially assembled pieces are sewn to other partially assembled pieces to
More informationPage 1 of 8. Printed: 27 MAR :48 AM S/L CASUAL JERSEY MAXI DRESS 06 AUG :50 AM TB9NXO 27 MAR :47 AM TB6BYJ
70666 Folder Summary - Wovens 70666 06 AUG 06 07:50 AM TB9NXO 7 MAR 07 0:47 AM TB6BYJ Agent: Pre-Dev Vendor: Prod Vendor: Muslin Needed: Li Fung Size Range: XS-XL Tech Designer: Gail Branch Suy, Co Designer
More informationSTONY APPAREL CORPORATION - LIVE GENERAL INFO STYLE: DIVISION: MARKET: G2865VAVAZ G- GIRLS MAY 2018
GENERAL INFO GR TARGT3:XS (4-5) S (6-6X) M (7-8) L (10-12) XL (14-16) XXL(18-20) TBD CDFs: DESIGNER: :FERNANDA 1ST PATTERN MAKER: :YANG :2018-05 SALES PERIOD: : TREND: : CUSTOMER: :TARGET CLASSIFICATION
More informationCreative Patterns. School Uniform Pattern Catalogue. Tuesday, 15 September 2009 NOTE: Information subject to change.
1 Creative Patterns School Uniform Pattern Catalogue Tuesday, 15 September 2009 NOTE: Information subject to change. 2 Creative Patterns At Creative Patterns we strive to create and deliver the best quality
More informationDefence Clothing (DC)
Manufacturing Specification for TUNIC, OFFICERS, FOOT GUARDS Defence Clothing (DC) PROPERTY OF MINISTRY OF DEFENCE Page 1 of 46 THE PRODUCT Item Description NATO Stock No. Pattern No. TUNIC, OFFICERS,
More informationDRAFT UGANDA STANDARD
DRAFT UGANDA STANDARD DUS 1687-4 First Edition 2017-mm-dd School Clothing Part 4: Shirts Reference number DUS 1687-4: 2017 UNBS 2017 DUS 1687-4: 2017 Compliance with this standard does not; of itself confer
More informationCover Page 9604 Womens Spring 2017
Cover Page 9604 Spring 2017 Copyright 2009-2016 by Gerber Technology. All rights reserved. Page 1 of 16 Printed By @ 6/28/2016 10:24:18 PM Style Process Details 9604 Spring 2017 Class Subclass Feature
More informationEC Altering Women's Ready Made Dresses
University of Nebraska - Lincoln DigitalCommons@University of Nebraska - Lincoln Historical Materials from University of Nebraska- Lincoln Extension Extension 1972 EC72-427 Altering Women's Ready Made
More informationEC Altering Women's Ready-Made Dresses
University of Nebraska - Lincoln DigitalCommons@University of Nebraska - Lincoln Historical Materials from University of Nebraska- Lincoln Extension Extension 1961 EC61-427 Altering Women's Ready-Made
More information2009-CE-HE (DRESS) HOME ECONOMICS (DRESS AND DESIGN)
HOME ECONOMICS (DRESS AND DESIGN) AIMS The aims of the examination are to test whether candidates have acquired : 1. an understanding of the place of textiles in modern fashions and the effect of social,
More informationHOME ECONOMICS (DRESS AND DESIGN)
HOME ECONOMICS (DRESS AND DESIGN) AIMS The aims of the examination are to test whether candidates have acquired : 1. an understanding of the place of textiles in modern fashions and the effect of social,
More informationLO-CA - CAMBRIDGE LOUNGE SHIRT
LO-CA - CAMBRIDG LOUNG SHIRT Features: double neck yoke double-rolled hem Fashionable lounge shirt trendy contrast insert on the button stand, cuffs and collar raised collar design with inner bone support
More informationSafety Award Program LOGO BROCHURE. Port & Company - Washed Twill Cap. CP78. Port & Company - Beanie Cap. CP91
ITEM A - 10 Points Port & Company - Washed Twill Cap. CP78 A great casual look with a smooth washed twill texture. Fabric Structure Profile Closure 100% cotton washed twill Unstructured Low Hook and loop
More informationC U STO M F L A N N E L
CUSTOM FLANNEL STYLE CATALOG 2017 DESIGN YOUR OWN CUSTOM FLANNEL In this catalog we will walk you though our flannel program. Start by selecting your pattern/ fit and move down the list. If you get stuck
More informationISSN: [Hanan* et al., 7(7): July, 2018] Impact Factor: 5.164
IJESRT INTERNATIONAL JOURNAL OF ENGINEERING SCIENCES & RESEARCH TECHNOLOGY EFFECTIVE WAY TO ESTIMATE THE STANDARD MINUTE VALUE (SMV) OF A U3 SHIRT BY USING TIME STUDY TECHNIQUE Hanan O.A 1, Seedahmed A.I.
More informationCover Page 9613 Womens Spring 2017
Cover Page 9613 Spring 2017 Copyright 2009-2016 by Gerber Technology. All rights reserved. Page 1 of 16 Printed By @ 6/28/2016 9:04:04 PM Style Process Details 9613 Spring 2017 Class Subclass Feature Detail
More informationFrench fly, or waist stay, for trousers/shorts
French fly, or waist stay, for trousers/shorts By: carolyn-s http://www.burdastyle.com/techniques/french-fly-or-waist-stay-for-t The French fly for trousers is a hidden extra closure with an inside button
More information~========================~
8-1303 Tooe ZTA245.7 B873 no \'3J~3L-~=============i1 CHILDREN'S CLOTHES,SIZE AND SELECTION ~========================~ Texas Agricultural Extension Service. The Texas A&M University System. Daniel C. pfannstiel,
More informationShipment locations: institutions stated below.
institutions stated below. The successful bidder shall be responsible for all costs relative to any exchanges, including, but not limited to, shipping and handling, transportation arid handling fees. NLCCW
More informationMUNDARING PRIMARY SCHOOL
MUNDARING PRIMARY SCHOOL UNIFORMS MUNDARING PRIMARY SCHOOL Uniform Catalogue Opening Hours 3.00-3.30pm Wednesdays Week 1,3,5 School terms only Order form is available at the end of the catalogue 1 Microfibre
More informationDerby Hat Skill Level: Beginner
Derby Hat Skill Level: Beginner Designed By Cassie Williams Sewn By Cassie Williams http://elegantitus.com And they re off! Thesaurus had a bit of an awkward start, Apple Jack broke well, Briar Rose is
More informationAdd To Order M355 Harriton Men s Side Blocked Micro-Piqué Polo 3.8 oz., 100% polyester micro-piqué, snag resistant, moisture-wicking, UPF 15, contrast blocking side, underarms and partial back collar,
More informationHeritage Pocket Polo
Page 2 101300 Heritage Pocket Polo 101300 Heritage Pocket Polo A classic Golden Bear style. As Jack says, Learn the fundamentals of the game and stick to them. This classic, go-to golf shirt certainly
More informationApparel Catalog. Ordering Procedure
Apparel Catalog The items included in this catalog have been chosen to provide Santa Anita A s members with a selection of high quality apparel which identifies the wearer as a member of the Santa Anita
More informationWEE WEKA INSTRUCTIONS FOR SEWING A POCKET NAPPY WITH LEG GUSSETS
WEE WEKA INSTRUCTIONS FOR SEWING A POCKET NAPPY WITH LEG GUSSETS Leg gussets help to guard against mushy whoopsies from escaping through the leg holes. They are also handy if you are running short of pockets/covers
More informationWho is Anchor Uniform Mfg.?
2016 Catalog Who is Anchor Uniform Mfg.? Anchor Uniform is a unique Manufacturer and distributor committed to producing exceptional garments. With the ability to complete all apparel manufacturing requirements
More informationDamián Márquez Tailoring & Alterations 91 Vivian Rd, Harborne B17 0DR Price Guide 2017
Damián Márquez Tailoring & Alterations 91 Vivian Rd, Harborne B17 0DR 0121-427-3356 Price Guide 2017 Trousers Length, Trousers from 16 Length, Trousers (with tape) from 17 Length, Trousers (with turn up)
More informationMaking Perfect Pants
Making Perfect Pants Guide C-227 Reviewed by Wendy Hamilton 1 Cooperative Extension Service College of Agricultural, Consumer and Environmental Sciences Women s fashions come and go, but pants are here
More informationPrinted: 10 APR :37 AM. Page 1 of 11 38" STAR DOBBY DRESS 11 NOV :26 PM TB7JYW 10 APR :36 AM TB8AXB
Folder Summary - Wovens Dresses (06) SM 07 NOV 06 06:6 PM TB7JYW 0 APR 07 08:6 AM TB8AXB Agent: Pre-Dev Vendor: Prod Vendor: Muslin Needed: Li Fung Range: Tech Designer: Annmarie Borneo Li Fung Designer
More informationBASKETBALL OUTFIT YOUR TEAM ADULT & YOUTH STOCK UNIFORMS TOPS BOTTOMS LADIES & GIRLS STOCK UNIFORMS TOPS BAGS...
OUTFIT YOUR TEAM UNIFORMS BASKETBALL JERSEYS SHORTS BAGS 1060 197 788 ADULT & YOUTH STOCK UNIFORMS... 60 TOPS... 67 BOTTOMS... 72 1065 865 1770 LADIES & GIRLS STOCK UNIFORMS... 76 TOPS... 81 BAGS... 82
More informationTOWNSHIP OF NUTLEY ESSEX COUNTY NEW JERSEY SPECIFICATIONS AND PROPOSAL FOR POLICE & CROSSING GUARD UNIFORMS & EQUIPMENT
TOWNSHIP OF NUTLEY ESSEX COUNTY NEW JERSEY SPECIFICATIONS AND PROPOSAL FOR POLICE & CROSSING GUARD UNIFORMS & EQUIPMENT 2017 1 NOTICE TO BIDDERS NOTICE IS HEREBY GIVEN that sealed bids will be received
More informationPatternMaker Software Hats & Caps Pattern Collection Designer: Leena Lähteenmäki
PatternMaker Software Hats & Caps Pattern Collection Designer: Leena Lähteenmäki INTRODUCTION This is a collection of patterns (not a macro) for twelve different styles of hats and caps. Most of the hats/caps
More informationEC Guides to Buying Women's Ready Made Dresses
University of Nebraska - Lincoln DigitalCommons@University of Nebraska - Lincoln Historical Materials from University of Nebraska- Lincoln Extension Extension 1972 EC72-421 Guides to Buying Women's Ready
More informationCover Page 9643 Womens Fall 2017
Cover Page 9643 Fall 2017 Copyright 2009-2016 by Gerber Technology. All rights reserved. Page 1 of 12 Printed By @ 3/16/2017 10:23:15 AM Style Process Details 9643 Fall 2017 Class Subclass Feature Detail
More informationTag #PatternOrchard on social media when sharing photos of items made from a Pattern Orchard pattern to spread the word about this free resource.
GARMENTS PERMIT Fitting fabric to the human body This tutorial is provided for free. It is for personal use, but may be shared in a social sewing group or public school to teach others. It is not to be
More informationCATALOG. G a r m e n t s TSHIRTDAVE
G a r m e n t s TSHIRTDAVE 1-877-644-4898 H o o d i e s, T - S h i r t s, P o l o S h i r t s, W o v e n S h i r t s & S p o r t s w e a r WWW.TSHIRTDAVE.NET 1-877-644-4898 Style # 2608 Men's Pullover
More informationMaxi Dress. 44/45 (112cm) 58/60 (150cm) 4.1/4 yards 4.1/4 yards
The Fine Print All patterns, photos, and information contained in this pattern are the property of Melissa Mora. All rights reserved. Reproduction and redistribution by any means are not permitted. No
More informationCOLLAR FOR MEN S SHIRT
COLLAR FOR MEN S SHIRT OTTOBRE design 7/2017, design 6 The collar instructions have been drawn up for men s shirts sewn from cotton poplin, chambray, lightweight denim, flannel, or similar fabric. PATTERN
More informationDO YOU HAVE BLOUSON: CERTIFIED DAY SHIFT WEAR FOR FIREMEN HB PROTECTIVE WEAR
DO YOU HAVE WHAT IT TAKES TO BLOUSON: CERTIFIED DAY SHIFT WEAR FOR FIREMEN 208 HB PROTECTIVE WEAR FLAMMGARD BE THERE FOR OTHERS? Firefighting is a vocation that plays an important role in protecting us
More informationJeans Protexall jeans are 100% cotton, relaxed fit. Available in 28-52, even waist sizes only Black Jeans Denim Jeans
020221 026600 022117 026117 Work Shirts Protexall work shirts are manufactured with comfort in mind. Quality features include longer tails and extra bar-tacking on the pockets for durability. Our shirts
More informationES 838 June 1979 CREWE THE LOOK YOU. Like-WITH LINE. Oregon State University Extension Service
ES 838 June 1979 CREWE THE LOOK YOU Like-WITH LINE Oregon State University Extension Service Becky Culp* Becoming clothes influence the way you look and feel. Visible lines in your clothes create illusions
More informationFolder Summary - Apparel Knits Folder Description
PJ504050P(SS) Folder Summary - Apparel Knits Agent: Li Fung Range: XS-XL Pre-Dev Vendor: Li Fung Technical Designer: Eleanor Lam Vendor: Designer: Betsy Perez Pre-: Jessenia Colon Sourcing Area: KTD Packing
More informationRegency Gown Pattern Instructions
Regency Gown Pattern Instructions Sense and Sensibility Clothing, 1998 (Revised 2003) Notes: I created this pattern after viewing three extant gowns belonging to museum collections in Virginia, D.C. and
More informationWelcome to the Edwards Transfer Store!
STORE CATALOG 2012 Table of Contents MEN S/UNISEX pg. 3-6 LADIES pg. 7-8 ACCESSORIES pg. 9 Logo Options Welcome to the Edwards Transfer Store! The edwardstransferstore.com catalog is set up for easy viewing
More informationMy Financial Future, Beginner
My Financial Future, Beginner A. General knowledge of consumer ed concepts B. Ability to explain decisions made or results shown C. Self-evaluation of project D. Understanding of Consumer Education Activities
More informationCheerleader Apron. for Seahawk Fans Designed by Anna-Beth at our Northgate store. Making the Bib. What You ll Need. First, Some Cutting
Cheerleader Apron for Seahawk Fans Designed by Anna-Beth at our Northgate store Every Hawk Hostess needs a Seahawks Cheerleader Apron! Be the envy of the neighborhood in this cheer-y team colors kick-pleat
More information2007 CLOTHING SPECIFICATIONS
CITY OF CONWAY 1201 Oak Street Conway, Arkansas 72032 Invitation and Bid 2007-08 INVITATION TO THE VENDOR ADDRESSED: Bidders are invited to furnish the items listed herein in accordance with the terms
More informationMen s Suit Measure your best fitting suit
Men s Suit Measure your best fitting suit Please note that the suit should be laid flat on a table or smooth surface for proper measurement. JACKET HALF CHEST Button up the coat and lay it on flat surface.
More informationSears Holdings Management Corporation FLOOR READY GUIDELINES
Sears Holdings Management Corporation FLOOR READY GUIDELINES 2010 Sears Brands, LLC September 2010 Sears Holdings Management Corporation (SHMC) Floor Ready Guidelines Introduction These guidelines provide
More informationSTYLE SUMMARY. Page: 1 Time: 17:29:59 Date: 8/03/12
STYLE SUMMARY SS/OP/OS NUMBER SS 011671 Catalogue Style Y Spec Approved By GARMENT TYPE Tabards Logo In Productionon N Pattern Approved By N Marker Approved By WORKING DIAGRAM SS011671 Page: 1 Lynne Francis
More informationTHE CREATIVE SEWING WORKSHOPS
THE CREATIVE SEWING WORKSHOPS Progressive Sewing Instruction: Building your wardrobe one garment element at a time! You will be able to create custom designs from the sloper made just for your body: including
More informationSHIRT STYLE&DESIGN MANUAL
SHIRT STYLE&DESIGN MANUAL Placket style Placket style 520Q Left & right placketfront 5102 Un-functional placket front 520D Gripping hidden button front 5118 Tuxedo front 4 2.5cm pleat for each side S-
More informationPROTECTION. COMFORT. DURABILITY. VALUE.
FLAME-RESISTANT CLOTHING 017-018 1 PROTECTION. COMFORT. DURABILITY. VALUE. Protection and peace of mind you should expect nothing less from the number-one brand in workwear. From our modest start as a
More informationFire Safe Associates. Will Patterson (919)
Fire Safe Associates Will Patterson (919) 557-6374 firesafe2000@aol.com Effective April 1, 2004 JACKET 1- GENERAL CONSTRUCTION BASE 32" WITH ACTION BACK WITH YOKE ON OUTER SHELL WITH YOKE ON LINER BASE
More informationGUIDE TO A PERFECT MEN S SUIT FIT
GUIDE TO A PERFECT MEN S SUIT FIT We value quality and perfection. We know that every man is different. Your size, posture, figure, and the shape of your body all change the way your suit fits. This is
More informationhi-visibility Work shirt: class 2 level 2
hi-visibility Work shirt: class 2 level 2 SS14 Real protection for real exposure. With UPF 40 and 360 visibility, you re protected day and night. Front and back paired with either yellow/green or orange
More informationCover Page 9610 Womens Spring 2017
Cover Page 9610 Spring 2017 Copyright 2009-2016 by Gerber Technology. All rights reserved. Page 1 of 9 Printed By @ 6/28/2016 3:11:10 PM Style Process Details 9610 Spring 2017 Class Subclass Feature Detail
More informationLined with 12 oz. Modaquilt. Breathable & washable. Naturally water repellent. 2 slash inside pockets. Elastic back at waist.
L2N1USD 11 OZ. ULTRA SOFT DUCK SLEEVED JACKET LINER Flame resistant 88 % Cotton 12 % high tenacity nylon. Lined with 12 oz. Modaquilt. Breathable & washable. Naturally water repellent. 2 slash inside pockets.
More informationARROW UNIFORM. Hanes 6.1 oz. Beefy-T. Anvil 4.5 oz. Long-Sleeve Fashion Fit Tee. Gildan 6.1 oz. Ultra Cotton Tee
Hanes 6.1 oz. Beefy-T Available in Youth (5380), and Adult (5180) 52 available colors 100% preshrunk ringspun cotton (some colors cotton/polyester blend) Seamless collar Double-needle coverseamed neck
More information1. DESCRIPTION APPLICABLE DOCUMENTS BY FMV SUPPLIED MATERIAL PRODUCT REQUIREMENTS MANUFACTURING...
1(54) M7351-156000-8 Vapenrock m/ä K1 Parade uniform jacket for soldier K1 M7352-114000-7 Ridbyxor m/ä K1 Parade riding pants K1 M7352-056000-7 Långbyxor m/ä K1 Parade trousers K1 Table of contents 1.
More informationPart 10: Chapter 17 Pleated Buttoning
Part 10: Chapter 17 Pleated Buttoning OUR last chapter covered the upholstering of one of the commonest forms of chair frames. The same chair may be upholstered with deeper buttoning, but instead of indenting
More informationCatalog Yes. Awarded Vendor Page 1 of 6
Company Name SISD Vendor Number Company Contact Address, City, State, Zip Phone: Fax: Email: Web Page Deviations Warranty Period Return Policy Delivery FREIGHT: The district requests that all deliveries
More informationWhat are the Elements of Design?
The Art of Fashion What are the Elements of Design? Elements are the building blocks of design. Rules of art that will create appealing designs. Elements of Design Line Shape Texture Color What lines appear
More informationPPAI ASI PPAI ASI FOOTBALL COACHES PPAI ASI PPAI ASI 37461
PPAI 187246 ASI 37461 PPAI 187246 ASI 37461 FOOTBALL COACHES 2012 www.augustasportswear.com PPAI 187246 ASI 37461 PPAI 187246 ASI 37461 NEW ONLINE DIGITAL RESOURCES CUSTOM FLYER DESIGNER PRESELECTED UNIFORM
More informationEASY CARE OXFORD SHIRTS
2018 BEST SELLERS EASY CARE OXFORD SHIRTS 061 021 000 Button-down collar. 010 026 006 001 023 003 005 Short-Sleeve Shirt 1027 Men s / 5027 Ladies Level 1 Level 2 Level 3 $22. 50 $25. 50 $29. 50 Long-Sleeve
More informationFabric Inspection Guideline
Fabric Inspection Guideline Quality Department 1. INTRODUCTION... 2 2. GENERAL... 3 2.1 H&M documents... 3 2.2 Fabric Technical Data... 3 2.3 Approved fabric... 3 2.4 Roll ticket information... 3 2.5 Fabric
More informationSECURITYWEARHOUSE.COM 2016 SECURITY. Contact:
SECURITYWEARHOUSE.COM 2016 SECURITY Contact: Sales@SecurityWearhouse.com 2 SECURITY 5580 1580 SECURITY 3 Performance Flat Knit Polo 1580 SHORT SLEEVE 100% polyester, 4.6 oz. 1580 Men s 5580 Ladies $21.90
More informationCAVANTAL. Buying file RA INTERNATIONAL. Created by : Last update : File download : Color Proto : fmispelaere ROSE
Collection : Universe : Fashion scale : Department : Family : Sub family : Active sizes : Fit : Folding type : ESSENTIAL 6- Basic 03 10 SHIRT LONG SLEEVES SHIRT Long sleeves Shirt XS S M L XL XXL Slim
More informationWide-Brim Sun Visor. by Vicki Welsh. A free project, compliments of...
A free project, compliments of... Wide-Brim Sun Visor by Vicki Welsh All information provided herein is done so in good faith. Three Creative Studios takes no responsibility for problems or issues encountered
More informationKArIBAN. 13 colours! 100/110 g/m 2 SIZES. SIZES XS S M L xl 2XL 3XL* 4XL* A/B
90 Corporate wear 91 13 colours! KA548 JUDITH - LADIES SHORT SLEEVE EASY CARE POLYCOTTON POPLIN SHIRT 65 % Polyester 35 % Cotton Poplin. Easy Care fabric. Soft Collar. Self coloured buttons. Left chest
More informationDropped Waistline. Waistline seam placed below the natural waistline
Dropped Waistline Waistline seam placed below the natural waistline Empire Waistline High-waisted effect with seam placed directly under the bust. Popular from late 18 th c. to 1820s during Empire and
More information