This isn t a complete guide, but it should show you enough to figure out how I did this and that.
|
|
- Gavin O’Neal’
- 6 years ago
- Views:
Transcription
1 I wanted to fit a Raspberry Pi running Retropie into a Gameboy Advance SP case. I didn t want to cut any new holes and it had to close up completely; no wires sticking out, no extra buttons in places they re not meant to be. It had to look as much like a normal Gameboy as possible. This build doesn t have any sound. The backlight button was programmed to be a lights out button on mine, and shuts down the Pi so I can turn it off easily. This isn t a complete guide, but it should show you enough to figure out how I did this and that. This was not an easy build. Parts list: Gameboy Advance SP aftermarket case Gameboy Advance SP hinges Raspberry Pi Zero Micro SD card Adafruit perma-proto half-sized Adafruit Powerboost mAh Battery (Dimensions: 5 cm x 3.4 cm x 0.6 cm) Adafruit PiTFT - 320x " TFT+Touchscreen for Raspberry Pi GPIO Ribbon Cable (any wire will do but this was thin and flexible) Power switch 4x4x0.8 SMD tactile push buttons 4x4x1.5 SMD tactile push buttons Optional: Gameboy cartridge Probably the biggest job was carving out the innards of the Gameboy case without breaking it (really need to buy myself a dremel).
2 For the programming, I used exactly the same image that I used for my previous Pi handheld (because it was efficient, and I m lazy) so you can follow the guide on that one to make this one work. I ll attach it to this thingiverse page too.
3 This is where the battery and Pi ended up (you can see how much I ve cut out of the case too): The battery was taped in place with electrical tape and was the very last thing I put into the case. I wasn t sure which way to put it so that the wire would be on the right corner. The battery cover for the Gameboy was screwed into place using the proper screws, so don t cut off any plastic that s need for that. The Pi was not glued or taped into place at all, it rests against some of the plastic and I left it free to move so that it would be easier to arrange wires as I closed it up. Here s the only picture I took of the perma-proto, showing where I soldered the buttons and where I cut the board:
4 Behind this I ve cut tracks in different places and soldered wires to make one of the top rails a common ground. Sadly I didn t take a pic of where I put the powerboost, there s a gap just below the A and B buttons, it s got 2 plastic ridges that it fit perfectly between (like it was made for it!). You ll need to make sure the perma-proto isn t too long or you ll be hitting the components on the board. This means that the powerboost goes under the board for the buttons as it s about as thick as the buttons themselves. I had to trim the edge off some of the rubber button bits to help this fit comfortably. Electrical tape is your friend. The micro USB socket on the powerboost can be accessed through the hole where the Gameboy s power switch was. I hot glued the powerboost into place first, after soldering on some wires that I would need for the power switch and wires for the Pi itself. Here s where to connect the wires The battery was attached
5 once everything was tested and working and ready to be closed up to avoid me shorting anything and frying it all. The start and select buttons are on a thin strip of perma-proto that I cut off. It was hot-glued into place and the ground wires were soldered to the main ground rail I d made on the other board. The shoulder buttons were rested along the top edge of the board and hot glued into place, you can just about see one here on the right (getting the perma-proto the right size was key to making this fit easily): You can also just about see how the powerboost fits under the board for the buttons at the top left (if you re looking closely, you ll notice that I ve got the power wires in the wrong holes on the powerboost, don t do this). The buttons use the proper rubber and plastic bits that came with the case. Here s the wiring guide I used, don t forget to wire ground for the buttons (the numbers by the button layout refer to the GPIO numbers):
6 Here s the screen wired up:
7 I split the wires into a group of 5, 3, and 1, then coloured an edge, this meant I d know which was which after it when through the hinge and I think it made them slightly easier to move around within the hinge. Here s my hideous soldering on the screen:
8 I trimmed down the screen to help it fit the case. Here s the back of the screen, showing where I cut it:
9 Test things when you can:
10 I didn t cut much out of the screen part of the case, the PITFT fit fairly well after being shortened. The screen sticks out the front a bit, but there isn t much I can do; it will still fold closed just like a normal Gameboy. I used some black electrical tape to hide the silver edge of the screen and the board below. The screen isn t glued into place at all; it just fits snugly between the plastic mouldings that the original screen uses. The power switch was hot glued into place so that it could be reached through the hole for the volume control slider. I cut up a Gameboy cartridge so that it would look the part. This can still be removed and is held in place by friction:
11 Had to be Doom:
12 After wrestling the wires into place and getting everything closed up, I made sure it all still worked. I put the hinges in place (make sure you put the plastic caps onto the hinges first, then push them in) and checked that it moved the way it was meant to. There s an extra piece of plastic that covers the wires in the hinge, make sure you screw that into place before you close it up. You will also want to put the shoulder buttons in. I super glued around the edge for the lower part. The screen part was screwed together using the proper screws. Final touch: put the Nintendo badge on the top and the sticker on the bottom so that it looks the part. Were I to build this again, I could do it a lot more neatly, but I really don t want to :P If I ve forgotten to mention anything, just leave a comment or send me a message directly on Thingiverse.
13
14
Portable Apple Watch Charger
Portable Apple Watch Charger Created by Ruiz Brothers Last updated on 2017-10-22 09:58:04 PM UTC Guide Contents Guide Contents Overview Smart Charging Prerequisite Guides Parts, Tool & Supplies Circuit
More information7 Portable Multitouch Raspberry Pi Tablet
7 Portable Multitouch Raspberry Pi Tablet Created by Ruiz Brothers Last updated on 2017-02-27 04:13:53 PM UTC Guide Contents Guide Contents Overview Portable Raspberry Pi Tablet 7" Multitouch Display Parts
More information3D Printed Google AIY Voice Kit
3D Printed Google AIY Voice Kit Created by Ruiz Brothers Last updated on 2018-01-09 12:47:26 AM UTC Guide Contents Guide Contents Overview 3D Print a DIY AI enclosure for the Raspberry PI! Parts, Tools
More informationAudio Prank Gift Box. Created by Becky Stern. Last updated on :46:15 PM UTC
Audio Prank Gift Box Created by Becky Stern Last updated on 2018-08-22 03:46:15 PM UTC Guide Contents Guide Contents Overview Circuit Diagram Prepare Components Build Circuit Wrap and Give 2 3 5 6 12 14
More informationDIY Wireless DDR Dance Pad with Bluefruit EZ-Key
DIY Wireless DDR Dance Pad with Bluefruit EZ-Key Created by Paul Beaudet Last updated on 2018-08-22 03:40:07 PM UTC Guide Contents Guide Contents Overview What's DDR? Materials Cheapo method - As Shown
More informationRaspberry Pi Selfie Bot
Raspberry Pi Selfie Bot Created by Sophy Wong Last updated on 2018-08-22 04:03:16 PM UTC Guide Contents Guide Contents Overview Parts & Supplies The Circuit Power Circuit Other Connections Laser Cutting
More informationFPV Mini Display. Created by Ruiz Brothers. Last updated on :00:18 PM UTC
FPV Mini Display Created by Ruiz Brothers Last updated on 2017-07-19 01:00:18 PM UTC Guide Contents Guide Contents Overview Mini FPV monitor Adafruit Parts Tools and Supplies Circuit Diagram Electronics
More informationLED Eyes. Created by Ruiz Brothers. Last updated on :50:55 AM UTC
LED Eyes Created by Ruiz Brothers Last updated on 2018-01-13 05:50:55 AM UTC Guide Contents Guide Contents Overview Parts, Tools and Supplies Enameled Copper Magnet Wire 11 meters / 0.1mm diameter Adafruit
More informationSolar Boost Bag. Created by Becky Stern. Last updated on :44:55 PM UTC
Solar Boost Bag Created by Becky Stern Last updated on 2018-08-22 03:44:55 PM UTC Guide Contents Guide Contents Overview 3D Design Files Customize Design Assemble Circuit Prepare Solar Panel Enclosure
More informationNo-Sew LED Wristband. Created by Kathy Ceceri. Last updated on :23:40 PM UTC
No-Sew LED Wristband Created by Kathy Ceceri Last updated on 2018-11-13 09:23:40 PM UTC Guide Contents Guide Contents Overview Playing with LED Options Suggested Parts List -- Electronics Suggested Materials
More informationRandomizing dice... ELECTRONIC PRODUCTS AT OLSJ. The Project begins...
Randomizing dice... ELECTRONIC PRODUCTS AT OLSJ New And Inclusive The Project begins... Stage Are you ready...ok let s go Collect PCB, then wire wool solder side, write name on Name Randomizing dice...page
More informationAdafruit Prototyping Pi Plate. Created by Ladyada
Adafruit Prototyping Pi Plate Created by Ladyada Guide Contents Guide Contents Overview Solder it! User Manual Buy Adafruit Prototyping Pi Plate 2 3 4 14 17 Adafruit Industries http://learn.adafruit.com/adafruit-prototyping-pi-plate
More informationDIY Bluetooth Gamepad
DIY Bluetooth Gamepad Created by Ruiz Brothers Last updated on 2016-09-03 02:23:21 AM UTC Guide Contents Guide Contents Overview Prerequisite Guides Expectations Parts Tools & Supplies Circuit Diagram
More informationToy Car Speed Timer. Created by Kirby Griese. Last updated on :13:49 PM UTC
Toy Car Speed Timer Created by Kirby Griese Last updated on 2017-03-20 09:13:49 PM UTC Guide Contents Guide Contents Overview Parts needed Prerequisites 3D Printing Assembly Wiring Software Use It 2 3
More informationCircuit Playground Express Head-Tilt Ears
Circuit Playground Express Head-Tilt Ears Created by Dave Astels Last updated on 2018-10-09 04:07:03 PM UTC Guide Contents Guide Contents Overview Parts Circuit Playground Express Micro servo Lithium Ion
More informationGame Grrl. Created by lady ada. Last updated on :35:07 PM UTC
Game Grrl Created by lady ada Last updated on 2018-08-22 03:35:07 PM UTC Guide Contents Guide Contents Overview So there I was... Specifications Make Parts Tools Step by step Extra stuff Resources Other
More informationPiGRRL 2. Created by Ruiz Brothers. Last updated on :41:35 AM UTC
PiGRRL 2 Created by Ruiz Brothers Last updated on 2018-05-24 08:41:35 AM UTC Guide Contents Guide Contents Overview Raspberry Pi Retro Game Console Easier to build! Project Expectations Adafruit Parts
More informationAdafruit Pi Cobbler Kit
Adafruit Pi Cobbler Kit Created by lady ada Last updated on 2018-08-22 03:30:27 PM UTC Guide Contents Guide Contents Overview Solder it! Buy a Pi Cobbler Kit! Downloads 2 3 5 15 16 Adafruit Industries
More information7" Portable HDMI Monitor
7" Portable HDMI Monitor Created by Ruiz Brothers Last updated on 2017-05-29 05:47:14 PM UTC Guide Contents Guide Contents Overview DIY Monitor Connect to a Raspberry pi Use as a second monitor Camera
More information3D Printed LED Buckle
3D Printed LED Buckle Created by Ruiz Brothers Last updated on 2018-08-22 03:38:02 PM UTC Guide Contents Guide Contents Overview Customize the Buckle Artwork, Design and Text Scale, Adjust and Combine
More informationPocket PiGRRL. Created by Ruiz Brothers. Last updated on :47:31 PM UTC
Pocket PiGRRL Created by Ruiz Brothers Last updated on 2018-08-22 03:47:31 PM UTC Guide Contents Guide Contents Overview Raspberry Pi This Guide Prerequisite Guides Parts Tools Supplies Circuit Diagram
More informationTent Lantern. Created by Timothy Reese. Last updated on :17:25 AM UTC
Tent Lantern Created by Timothy Reese Last updated on 2017-07-14 05:17:25 AM UTC Guide Contents Guide Contents Overview Things you'll need: What You'll Learn: 3D Printing Code Assembly Wiring Diagram Soldering
More informationMini Mac Pi. Created by Ruiz Brothers. Last updated on :43:27 PM UTC
Mini Mac Pi Created by Ruiz Brothers Last updated on 2018-08-22 03:43:27 PM UTC Guide Contents Guide Contents Overview Build Your Own Mac Pi How it Works Project Advisory Challenges and Expectations Prerequisite
More informationLuminous LED Flowers. Created by Becky Stern. Last updated on :47:44 PM UTC
Luminous LED Flowers Created by Becky Stern Last updated on 2018-08-22 03:47:44 PM UTC Guide Contents Guide Contents Overview Circuit Diagram Prepare LED Sequins Affix Inside Bouquet Connect Battery &
More informationOverwatch Prop Gun: Lucio's Blaster Pt. 3
Overwatch Prop Gun: Lucio's Blaster Pt. 3 Created by John Park Last updated on 2017-11-24 09:48:21 PM UTC Guide Contents Guide Contents 3D Printing Circuit Building Assembly Front Assembly Rear Assembly
More informationPing Pong Ball Launcher
Ping Pong Ball Launcher Created by Dano Wall Last updated on 2019-01-25 03:19:13 AM UTC Guide Contents Guide Contents Overview Electronic Parts Circuit Playground Express USB cable - USB A to Micro-B Alkaline
More informationInfinity Mirror Valentine's Candy Box
Infinity Mirror Valentine's Candy Box Created by Kathy Ceceri Last updated on 2019-02-07 09:44:54 PM UTC Guide Contents Guide Contents Overview Parts List -- Mini Box Version Chibitronics Color LEDs Add-On
More information'Sup Brows. Created by Kate Hartman. Last updated on :52:04 PM UTC
'Sup Brows Created by Kate Hartman Last updated on 2018-08-22 03:52:04 PM UTC Guide Contents Guide Contents Overview Circuit Bluetooth Test Upload the Code Place the Sensor View Sensor Values Via Bluetooth
More informationCPX Mystery Dreidel. Created by Kathy Ceceri. Last updated on :51:40 PM UTC
CPX Mystery Dreidel Created by Kathy Ceceri Last updated on 2018-12-04 02:51:40 PM UTC Guide Contents Guide Contents Overview Parts List -- Electronics Circuit Playground Express USB cable - USB A to Micro-B
More informationFeatherWing Proto and Doubler
FeatherWing Proto and Doubler Created by lady ada Last updated on 2016-09-19 05:11:36 PM UTC Guide Contents Guide Contents Overview FeatherWing Proto FeatherWing Doubler Proto Pinout Proto Pinout Duplicated
More informationNeon LED Signs. Created by John Park. Last updated on :11:09 PM UTC
Neon LED Signs Created by John Park Last updated on 2018-08-22 04:11:09 PM UTC Guide Contents Guide Contents Overview Parts Materials Tools Build the Sign Driver Preparation Solder the Circuit Solder the
More information3D Printed Glow-Spike Bracelet
3D Printed Glow-Spike Bracelet Created by Rick Winscot Last updated on 2014-08-13 12:00:11 PM EDT Guide Contents Guide Contents 3D Printing Battery Compartments LED Spikes Wiring / Soldering 2 3 4 11 17
More informationPyPortal View Master Created by Ruiz Brothers. Last updated on :51:28 AM UTC
PyPortal View Master Created by Ruiz Brothers Last updated on 2019-03-13 11:51:28 AM UTC Overview In this project we re building a view master inspired device using Adafruit s PyPortal. The eyepiece makes
More informationNaughty or Nice Machine
Naughty or Nice Machine Created by Brian Corteil Last updated on 2018-08-22 03:45:31 PM UTC Guide Contents Guide Contents Overview It knows if you have been Naughty or Nice! Make It! Parts The Case The
More information3D Printed Camera LED Ring
3D Printed Camera LED Ring Created by Ruiz Brothers Last updated on 2018-08-22 03:39:34 PM UTC Guide Contents Guide Contents Overview DIY LED Ring Light Prerequisite Guide: Parts List: Tools & Supplies
More informationPaper Airplane Launcher
Paper Airplane Launcher Created by Dano Wall Last updated on 2018-08-27 08:36:14 PM UTC Guide Contents Guide Contents Overview A Launching Platform The Electronics Materials Build the Launcher Attach Motors
More informationBunny Ears with MakeCode
Bunny Ears with MakeCode Created by Erin St Blaine Last updated on 2018-08-22 04:05:47 PM UTC Guide Contents Guide Contents Introduction Tools & Other Materials Programming with MakeCode Set Up the Light
More informationEasy Sparkle Pocket T-Shirt
Easy Sparkle Pocket T-Shirt Created by Erin St Blaine Last updated on 2018-10-18 06:45:05 PM UTC Guide Contents Guide Contents Overview Parts Materials Needed Code with MakeCode Vinyl Cutting Sizing and
More informationTrinket NeoPixel LED Longboard
Trinket NeoPixel LED Longboard Created by Ruiz Brothers Last updated on 2017-10-02 06:00:32 PM UTC Guide Contents Guide Contents Overview Parts Tools & Supplies Prerequisite Guides 3D Printing PLA Material
More informationMad Science Test Tube Rack
Mad Science Test Tube Rack Created by John Park Last updated on 2016-10-17 09:21:01 PM UTC Guide Contents Guide Contents Overview Lighted Test Tube Parts Materials and Tools Optional Test Tube Rack Parts
More informationFeatherWing Proto, Doubler and Tripler
FeatherWing Proto, Doubler and Tripler Created by lady ada Last updated on 2018-11-15 10:39:12 PM UTC Guide Contents Guide Contents Overview FeatherWing Proto FeatherWing Doubler FeatherWing Tripler Proto
More informationHammer Time Mini Golf Hazard with Crickit
Hammer Time Mini Golf Hazard with Crickit Created by John Park Last updated on 2018-07-09 06:47:53 AM UTC Guide Contents Guide Contents Overview Please Hammer, Don't Hurt Em Parts Materials & Tools Program
More informationMotion-Activated Solder Fume Extractor With Lamp
Motion-Activated Solder Fume Extractor With Lamp Created by Jan Goolsbey Last updated on 2017-10-22 12:40:07 AM UTC Guide Contents Guide Contents Overview Project Components Adafruit Components: Other
More informationAdaBox 005. Created by Tyler Cooper. Last updated on :08:13 PM UTC
AdaBox 005 Created by Tyler Cooper Last updated on 2017-09-27 08:08:13 PM UTC Guide Contents Guide Contents Introduction Hi there! Who is this for? Who isn't this for? Who are you? Unboxing AdaBox 005
More informationAdafruit AMG8833 8x8 Thermal Camera Sensor
Adafruit AMG8833 8x8 Thermal Camera Sensor Created by Justin Cooper Last updated on 2017-11-27 10:00:27 PM UTC Guide Contents Guide Contents Overview Pinouts Power Pins: Logic pins: Assembly Prepare the
More informationAdabot Operation Game
Adabot Operation Game Created by John Park Last updated on 2018-08-22 04:11:17 PM UTC Guide Contents Guide Contents Overview Parts Materials & Tools Build the Operating Table Print the Board and Pieces
More informationCelebration Spectacles
Celebration Spectacles Created by Becky Stern Last updated on 2018-08-22 03:45:59 PM UTC Guide Contents Guide Contents Overview Circuit Diagram Assemble Circuit Test and Glue Wear 'em! 2 3 6 7 10 14 Adafruit
More informationFiddy - the FTDI Clip
Fiddy - the FTDI Clip Created by Timothy Reese Last updated on 2016-11-22 09:18:04 PM UTC Guide Contents Guide Contents Overview FTDI is Great! Things you'll need: What You'll Learn: 3D Printing Assembly
More information3D Printed Bone Conduction Transducer Box
3D Printed Bone Conduction Transducer Box Created by Ruiz Brothers Last updated on 2018-08-22 03:40:25 PM UTC Guide Contents Guide Contents Overview Tools & Supplies Parts 3D Printing Circuit Diagram Stereo
More informationCrickit Carnival Bumper Bot
Crickit Carnival Bumper Bot Created by John Park Last updated on 2018-08-22 04:08:52 PM UTC Guide Contents Guide Contents Overview Parts Materials and Tools Build the Bumper Bot Cut the Cardboard Chassis
More informationMINI TRICORN HAT PATTE BRIM CUT 1 BUCKRAM ADD 1CM AND EITHER CUT 2 MIN FABRIC OR CUT 1 MAIN FABRIC & CUT 1 CONTRASTING FABRIC CENTRE BACK LINE
BRIM CUT 1 BUCKRAM ADD 1CM AND EITHER CUT 2 MIN FABRIC OR CUT 1 MAIN FABRIC & CUT 1 CONTRASTING FABRIC CENTRE BACK LINE CUT SMALL CENTRE OVAL OUT OPTIONAL CUT 1 BONDAWEB MINI TRICORN HAT PATTE A1 CROWN
More informationGuardian Shield+ Zelda Breath of the Wild
Guardian Shield+ Zelda Breath of the Wild Created by Ruiz Brothers Last updated on 2018-08-22 04:01:50 PM UTC Guide Contents Guide Contents Overview Articulating Handle Rechargeable Prerequisite Guides
More informationTrellis 3D Printed Enclosure
Trellis 3D Printed Enclosure Created by Ruiz Brothers Last updated on 2018-08-22 03:39:07 PM UTC Guide Contents Guide Contents Overview Parts Tools & Supplies Modeling 123D Design Customize Measuring Parts
More informationLED Eye Prosthetic. Created by Tully Jagoe. Last updated on :00:17 AM EST
LED Eye Prosthetic Created by Tully Jagoe Last updated on 2014-12-11 11:00:17 AM EST Guide Contents Guide Contents Overview Parts List Prepare wires Solder LEDs Attach battery holder Shape it to your skull
More informationCircuit Playground Yoyo
Circuit Playground Yoyo Created by Ruiz Brothers Last updated on 2018-01-13 05:56:02 AM UTC Guide Contents Guide Contents Overview 3D Printed NeoPixel Yoyo History of the Yo-Yo Expectations Parts Tools
More informationCon Badge with Circuit Playground Express
Con Badge with Circuit Playground Express Created by Sophy Wong Last updated on 2018-04-11 05:00:16 PM UTC Guide Contents Guide Contents Overview Tools & Materials Laser Cutting Program the Circuit Playground
More information3D Printing Guide: MakerBot Replicator 2X
SOUTHERN POLYTECHNIC STATE UNIVERSITY 3D Printing Guide: MakerBot Replicator 2X Operating and Troubleshooting Guide Architecture Department 8/13/2014 Revision Table Version Dated Description By 1.00 06/25/2014
More informationStumble-Bot. Created by Dano Wall. Last updated on :04:06 AM UTC
Stumble-Bot Created by Dano Wall Last updated on 2018-09-06 05:04:06 AM UTC Guide Contents Guide Contents Overview Simply Stumbling We Have the Technology Other Supplies Leg Assembly Front Legs Back Legs
More informationRaspberry Pi Pipboy 3000
Raspberry Pi Pipboy 3000 Created by Ruiz Brothers Last updated on 2017-08-09 01:44:21 AM UTC Guide Contents Guide Contents Overview Functional Cosplay Props Electronic Parts & Components Tools & Supplies
More informationNeoPixel Fairy Crown. Created by Erin St Blaine. Last updated on :22:47 AM UTC
NeoPixel Fairy Crown Created by Erin St Blaine Last updated on 2018-12-31 02:22:47 AM UTC Guide Contents Guide Contents Overview Adafruit NeoPixel LED Dots Strand - 20 LEDs at 2" Pitch Adafruit GEMMA M0
More informationCreate your own handmade drum lampshade!
Create your own handmade drum lampshade! Using your own you can make a one-of-a-kind lampshade for a lampbase or to use as a pendant to hang from the ceiling. Included in the kit: 1 x Lampshade ring set
More informationBoomy The Boombox. Created by Ruiz Brothers. Last updated on :52:13 PM UTC
Boomy The Boombox Created by Ruiz Brothers Last updated on 2017-09-05 08:52:13 PM UTC Guide Contents Guide Contents Overview Boomy The Boombox AdaBox 004 Parts 3D Printing 3D Printed Parts Enclosure Design
More informationQi Wireless Recharging Battery Case
Qi Wireless Recharging Battery Case Created by Rick Winscot Last updated on 2015-11-04 12:50:13 PM EST Guide Contents Guide Contents Introduction Disassembly Guts! Testing 2 3 5 10 16 Adafruit Industries
More informationNeoLoch. Inquisitor Core. Assembly Instructions (9/3/2015)
NeoLoch Inquisitor Core Assembly Instructions (9/3/2015) Your kit should contain the following items. If you find a part missing, please contact NeoLoch for a replacement. Kit contents: 1 PCB 1 2.1mm DC
More informationCoffee Detonator: The TNT Plunger Grinder
Coffee Detonator: The TNT Plunger Grinder Created by John Park Last updated on 2017-04-12 08:04:36 PM UTC Guide Contents Guide Contents Overview Materials Voltage Conversion AC/DC Voltage Divider Microcontroller
More information3D Printed LED Knuckle Jewelry
3D Printed LED Knuckle Jewelry Created by Ruiz Brothers Last updated on 2015-02-20 09:31:06 AM EST Guide Contents Guide Contents Overview Prerequisite Guides Parts Tools & Supplies 3D Printing Filament
More informationCup o' Sound. Created by Becky Stern. Last updated on :30:06 PM EST
Cup o' Sound Created by Becky Stern Last updated on 2015-02-18 01:30:06 PM EST Guide Contents Guide Contents Overview Circuit Diagram Load Sound and Prepare Components Solder Circuit and Assemble Use it!
More informationLED Stego Flex Spike Hoodie
LED Stego Flex Spike Hoodie Created by Becky Stern Last updated on 2015-02-19 04:45:44 PM EST Guide Contents Guide Contents Overview Like this project? 3D Print Spikes NinjaFlex Assemble Circuit Layout
More informationSimple LED Unicorn Horn
Simple LED Unicorn Horn Created by Ruiz Brothers Last updated on 2018-08-22 03:56:14 PM UTC Guide Contents Guide Contents Overview 3D Printed Unicorn Horn Want More Magic/Colors? Great For Beginners Parts
More informationLED Breath Stats Mask
LED Breath Stats Mask Created by Michael Sklar Last updated on 2018-01-11 11:09:33 PM UTC Guide Contents Guide Contents Overview Materials Asssembly CircuitPython Code Wear It 2 3 4 6 10 13 Adafruit Industries
More informationSlider Crank Mechanism -- from Cardboard and Craft Sticks
Slider Crank Mechanism -- from Cardboard and Craft Sticks Created by John Park Last updated on 2018-08-22 04:07:21 PM UTC Guide Contents Guide Contents Overview Materials Tools Build the Slider Crank Build
More informationTRON Bag. Created by Becky Stern
TRON Bag Created by Becky Stern Last updated on 2018-08-22 03:30:39 PM UTC Guide Contents Guide Contents Overview Tools Design Soldering Sewing Detailing Splitting Finishing Buy EL! Forums 2 3 5 7 12 15
More informationCircuit Playground Express Laser Tag
Circuit Playground Express Laser Tag Created by John Park Last updated on 2017-11-14 01:56:23 AM UTC Guide Contents Guide Contents Build a Laser Tag Game Code the Laser Tag Game MakeCode Transmitting IR
More informationClockwork Goggles. Created by John Park. Last updated on :03:10 PM UTC
Clockwork Goggles Created by John Park Last updated on 2018-08-22 04:03:10 PM UTC Guide Contents Guide Contents Overview Assemble Circuit and Goggles CircuitPython Setup and Code Rock the Goggles 2 3 6
More informationMagical Mistletoe. Created by Leslie Birch. Last updated on :45:29 PM UTC
Magical Mistletoe Created by Leslie Birch Last updated on 2018-08-22 03:45:29 PM UTC Guide Contents Guide Contents Overview Tools & Supplies Circuit Diagram Test the Sensor Prepare Parts Attach LED Sequins
More informationNeoPixel Ring Bangle Bracelet
NeoPixel Ring Bangle Bracelet Created by Becky Stern Last updated on 2017-09-28 11:14:48 PM UTC Guide Contents Guide Contents Overview Circuit Diagram Build it! Arduino Code CircuitPython Code Planning
More informationTrinket-Powered Conference Room Occupancy Display
Trinket-Powered Conference Room Occupancy Display Created by Mike Barela Last updated on 2018-08-22 03:38:56 PM UTC Guide Contents Guide Contents Overview Build Wiring Diagrams Populating the Board Code
More informationMystical LED Halloween Hood
Mystical LED Halloween Hood Created by Becky Stern Last updated on 2017-09-28 11:13:20 PM UTC Guide Contents Guide Contents Overview NeoPixel GEMMA circuit Arduino Code NeoPixel Überguide: Arduino Library
More informationFLORA Pixel Brooch. Created by Becky Stern. Last updated on :19:07 PM EST
FLORA Pixel Brooch Created by Becky Stern Last updated on 2015-02-20 01:19:07 PM EST Guide Contents Guide Contents Overview Connect first signal wire Connect power and ground wires Add more pixels Program
More informationAndroid GBoard Morse Code Control with Circuit Playground Express
Android GBoard Morse Code Control with Circuit Playground Express Created by Dave Astels Last updated on 2018-08-22 04:10:30 PM UTC Guide Contents Guide Contents Overview Parts Materials for the box Installing
More informationPushrod Garage. Created by John Park. Last updated on :07:30 PM UTC
Pushrod Garage Created by John Park Last updated on 2018-08-22 04:07:30 PM UTC Guide Contents Guide Contents Overview Parts & Materials Tools Pushrod Mechanism Code it with MakeCode Functions On Start
More informationWind Blowing Emoji Prop
Wind Blowing Emoji Prop Created by John Park Last updated on 2018-08-22 04:05:17 PM UTC Guide Contents Guide Contents Overview Code it with MakeCode Start Up Variables On Loud Sound If - Else Iterate Debounce
More informationFLORA TV-B-Gone. Created by Becky Stern. Last updated on :32:57 PM UTC
FLORA TV-B-Gone Created by Becky Stern Last updated on 2018-08-22 03:32:57 PM UTC Guide Contents Guide Contents Overview Parts Tutorials Transistors Resistors LEDs Pushbutton Program it Power Fabric pinwheel
More informationFiddy - the FTDI Clip
Fiddy - the FTDI Clip Created by Timothy Reese Last updated on 2018-08-22 03:57:42 PM UTC Guide Contents Guide Contents Overview FTDI is Great! Things you'll need: What You'll Learn: 3D Printing Assembly
More informationAdafruit LED Sequins. Created by Becky Stern. Last updated on :02:00 AM UTC
Adafruit LED Sequins Created by Becky Stern Last updated on 2018-03-02 04:02:00 AM UTC Guide Contents Guide Contents Overview Sewing with conductive thread Circuit Diagram GEMMA sequin hat Arduino Code
More informationi2c/spi LCD Backpack Created by lady ada Last updated on :11:04 PM UTC
i2c/spi LCD Backpack Created by lady ada Last updated on 2017-08-16 05:11:04 PM UTC Guide Contents Guide Contents Overview Which LCD to Use? Wait - the backpack has 16 holes, but my LCD only has 14 pins!
More informationDOUBLE HOMECOMING MUM INSTRUCTIONS
Hello! Thank you for choosing Melz Mumz for your homecoming supplies! I hope you find these instructions helpful and also visit vintagescrapping.typepad.com to see lots of step by step picture braid tutorials
More informationAlldaymall A88X LCD Screen Replacement
Restore the display capabilities of your device by replacing a defective or broken LCD screen. Written By: Drhaber ifixit CC BY-NC-SA www.ifixit.com Page 1 of 12 INTRODUCTION The Alldaymall A88X features
More informationAdafruit TPL5110 Power Timer Breakout
Adafruit TPL5110 Power Timer Breakout Created by lady ada Last updated on 2017-12-11 06:28:19 AM UTC Guide Contents Guide Contents Overview Pinouts Power Pins Control Pins Assembly Prepare the header strip:
More informationFeather Weather Lamp. Created by Ruiz Brothers. Last updated on :54:26 PM UTC
Feather Weather Lamp Created by Ruiz Brothers Last updated on 2018-08-22 03:54:26 PM UTC Guide Contents Guide Contents Overview Weather Reactive Pixels Prerequisite Guides Parts Tools & Supplies Circuit
More informationAdafruit Capacitive Touch Sensor Breakouts
Adafruit Capacitive Touch Sensor Breakouts Created by Bill Earl Last updated on 2018-08-22 03:36:13 PM UTC Guide Contents Guide Contents Overview Momentary Toggle 5-Pad Momentary Assembly and Wiring Installing
More informationLarge Pi-based Thermometer and Clock
Large Pi-based Thermometer and Clock Created by Simon Monk Last updated on 2017-09-12 03:11:01 PM UTC Guide Contents Guide Contents Overview Parts Raspberry Pi 3 - Model B - ARMv8 with 1G RAM Adafruit
More informationCrawling Animatronic Hand
Crawling Animatronic Hand Created by Dano Wall Last updated on 2018-12-03 06:39:35 PM UTC Guide Contents Guide Contents Overview Parts Used Tools & Materials Prepare the Hand Your hand is now ready to
More informationProphet 600 GliGli mod
Prophet 600 GliGli mod Created by Collin Cunningham Last updated on 2018-08-22 04:04:56 PM UTC Guide Contents Guide Contents Overview What you'll need Program the Teensy++ Modify the Teensy++ Prep header
More informationArduino Lesson 6. Digital Inputs
Arduino Lesson 6. Digital Inputs Created by Simon Monk Last updated on 2018-02-27 10:20:04 PM UTC Guide Contents Guide Contents Overview Parts Part Qty Breadboard Layout Arduino Code Push Switches Other
More informationThe Scream: Interactive Screaming Painting
The Scream: Interactive Screaming Painting Created by John Park Last updated on 2018-08-22 04:10:47 PM UTC Guide Contents Guide Contents Overview Parts & Materials Optional Build the Interactive Painting
More informationNeoPixel Bike Light. Created by Ruiz Brothers. Last updated on :43:46 PM UTC
NeoPixel Bike Light Created by Ruiz Brothers Last updated on 2018-11-15 07:43:46 PM UTC Guide Contents Guide Contents Overview 3D Printed Headlight Adafruit's Feather Platform Circuit Python Powered Parts
More informationAdafruit 8x16 LED Matrix FeatherWing
Adafruit 8x16 LED Matrix FeatherWing Created by lady ada Last updated on 2016-05-20 01:58:38 PM EDT Guide Contents Guide Contents Overview Pinouts Power Pins I2C pins Address Jumpers Changing Addresses
More informationPOST-PROCESSING YOUR 3D PRINTS
MAKERBOT EDUCATORS GUIDEBOOK GOING FURTHER: POST-PROCESSING GOING FURTHER POST-PROCESSING YOUR 3D PRINTS PAGE 160 SANDING YOUR 3D PRINTS 3D printing can bring your ideas to life, but sometimes your ideas
More informationInteractive Gift Box. Created by codingpro. Last updated on :47:40 AM UTC
Interactive Gift Box Created by codingpro Last updated on 2018-01-10 01:47:40 AM UTC Guide Contents Guide Contents Overview Adafruit GEMMA M0 - Miniature wearable electronic platform Lithium Ion Polymer
More information